I did try the bugfix-2.0.X this morning and can confirm it solves the problem for reprapworld_keypad with Megatronics 3.3. Thanks!by bbg - Firmware - Marlin
I think I found the problem (and think it is a bug in Marlin). In the file "buttons.h" BUTTON_CLICK is defined when IS_RRW_KEYPAD (lines 71-75): #ifdef EN_C #define BUTTON_CLICK() ((buttons & EN_C) || RRK(EN_KEYPAD_MIDDLE)) #else #define BUTTON_CLICK() RRK(EN_KEYPAD_MIDDLE) #endif where EN_C is the bitmask associated with the encoder switch. I think the idea is that clicks caby bbg - Firmware - Marlin
@Dust Sharp! However, the keypad is compatible with Megatronics 3.3. In Megatronics 3.2 they changed the pin-out of headers (always a bad idea) causing that specific version to be incompatible with the keypad. In version 3.3 they reverted back to the old pin-out before V3.2 (but did rotate the header 180 degrees wrt V3.1) . So the keypad is specifically not compatible with 3.2 but it is compatibby bbg - Firmware - Marlin
Hi all, Recently I upgraded to 2.0.9.2 and added a 2004 character LCD display and a reprapworld_keypad to one of my printers. As controller board I'm using a Megatronics V3.3 . The LCD and encoder (with switch) are working correctly if I'm enable ULTIPANEL in the configuration file: #define ULTIPANEL However, when I also enable REPRAPWORLD_KEYPAD the encoder (and switch) stops working: #defiby bbg - Firmware - Marlin
Hello, I might have missed this one, but is it possible in Slic3r to automatically compensate for the extrusion width? Let me explain further. A cylinder which is drawn in CAD with an outer diameter of 10.0mm will be printed as a cylinder with diameter 10.4mm (my extrusion width is 0.4mm). Slic3r generates a tool path that follows exactly the outer contours of the STL file. Is there an option iby bbg - Slic3r
Het bouwen is redelijk gevorderd. Ik heb alles nog los op een plaat triplex staan maar de eerste (redelijk fatsoenlijke) printjes komen eruit. Ik ben de boel nog aan het calibreren. Daarbij gebruik ik Triffids Calibration Guide (http://reprap.org/wiki/Triffid_Hunter's_Calibration_Guide). Met name het fine tunen van de steps van de Extruder moet nog afgemaakt worden. Maar bij het printen van grotby bbg - Projecten
Not sure if this helps as your problem description is not very specific. But last night I was testing myself the cold extruder of the Prusa i3 I'm building and ran into the following. I was giving "G1 E10" commands and the filament was not moving at all. Till I realized the E10 were absolute coordinates. Switching to relative coordinates with "G91" solved it. Now the extruder was feeding 10mm wiby bbg - Prusa i3 and variants
Dank je Frans. Gister de electronica aan elkaar geknoopt. Megatronics v3.0 board met DRV8825 drivers en nema17 motoren. Op het board de test firmware van RRW geflashed. Alles lijkt naar behoren te functioneren. Max stroom van de 8825 voor nu op 1A afgeregeld (2.5A Motoren). Dat gaan we later wel tunen. De DRV8825 hebben een "fault signal" in geval van te veel warmte/te grote stroom. Deze fout cby bbg - Projecten
Hallo allemaal, Ik ga de komende weken proberen een Prusa i3 te bouwen. De meeste onderdelen zijn binnen. De kunstof onderdelen krijg ik pas volgende week. Maar ik kan beginnen met de electronics. Met het bouwen van de printer hoop ik veel te leren over 3D printen (en wat belangrijk is bij het ontwerpen van een 3D printer). Ik heb een (profesionele) achtergrond in mechatronica (dynamics &by bbg - Projecten