There are very few videos available on this board, and not much information on how to get the 2209's V1.2 working with the GTR V1.0 board. I'm running all this on an Ender 5 Plus, with a BTT 12864 LCD screen (the ribbon cable for the TFT70 I ordered arrived damaged and is being replaced). Currently my hot end and heat bed work, and my stepper motors turn the correct direction, but the X/Y axisby Recoil1980 - Controllers
I replaced the original Creality board in my Ender 5 Plus with a Big Tree Tech SKR 1.4 Turbo. I do not know what happened, but suddenly after 3 weeks the board quit connecting to the TFT screen and OctoPrint. After a discussion with BTT's support, I determined the board (somehow) was fried. I could not place blame on the company as I could not determine if it was a manufacturing issue or if Iby Recoil1980 - General
Currently I have an Ender 5 Plus with Marlin 2.0.6.1 installed on a Big Tree Tech SKR 1.4 Turbo and TFT35 V2.0. The TFT is touch screen only, so not sure what impact that has, but when I start a print on the OctoPrint webpage the TFT stays on the screen it was previously set on (if I was in the move axis screen it will stay there). This has caused problems when I start a print and I forget to sby Recoil1980 - Firmware - Marlin
Sorry I am just getting back around to responding. I eventually sent the printer back. I think the sensor was just bad, then the LCD screen went white and I was unable to use it at all. I spend the extra money and got an Ender 5 Plus. So far the new one is running, but there are still a few issues with it.by Recoil1980 - CoreXY Machines
Currently I am having some issues with the proximity sensor that came with the printer (see here), so I have hooked up the extra limit switch that it came with and wired it to the board. Does anyone know what settings to change in Marlin to remove the proximity sensor and just use the limit switch instead? I am not clear on what I am supposed to comment and uncomment.by Recoil1980 - CoreXY Machines
I just purchased this printer: Tronxy X5SA Pro The first day after everything was setup it was printing fine on the heatbed with stock firmware. I honestly have no idea what changed, either mechanically or otherwise, but it began not wanting to bring the nozzle all the way down to the bed. The z offset was saving correctly, but it would still return to the same height on the bed. The first thby Recoil1980 - Reprappers
I have 3 of these, or should say had, connected and verified the polarity on them (https://www.amazon.com/gp/product/B00BF3S83C/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1). They still were not working no matter which pins I was trying to hook up. So I took them off and tested a couple of other fans, which worked...the fans I originally was trying are no longer working for some reason.by Recoil1980 - Controllers
Update: I went through the Marlin configuration for my Anet setup, and cross verified several settings that were not made when I did a fresh install for this new board. There are too many to list individually, but that fixed my issue with the axis movements... My end stops were wired up wrong, and I had to wire them up to be connected to the GND and D# pins on the connectors. The only problemby Recoil1980 - Controllers
Apologies in advance for a lengthy post. I am fairly new to 3d printing. I recently converted my Anet A8 to the AM8, running only 1 z motor with a timing belt at the top of the frame. Shortly after upgrading it would run a priming line at the front, but then started printing at the front where it stopped priming at instead of moving to the center. No settings had changed to cause this, it staby Recoil1980 - Controllers