Show all posts by user
People building or using RepRaps.
Re: Scaling - 12 years ago
NM my part was wacked...25.4 on a good stl works fine thought i was goin crazyby DanielG - Repetier
Scaling - 12 years ago
If a part is done in inches whats the approximate correct scale? Right now the part is tiny... I dont hae the ability to change the part to mm... I did this before but for the life of cannot find ref to it again! any help?by DanielG - Repetier
Re: Azteeg X3 Controller Pre-Order. Limited time pricing. - 12 years ago
That display looks VERY nice! You should have a enclosure ready on thingverse (or your site) at the ready when you release so people can print and mount this properly!!! They will love you for it!.. also will it come in a dark color as well?by DanielG - For Sale
Custom Buttons? - 12 years ago
Any thoughts on custom buttons like pronterface? It would make using the M42 command sooo much easier... Thanks for all your hard work! This is hands down the VERY best host period!by DanielG - Repetier
Re: Azteeg X3 Controller Pre-Order. Limited time pricing. - 12 years ago
Hows it going with the rest of the orders?by DanielG - For Sale
Re: Motors off? - 12 years ago
Yes, My bad ... I'll yap at sound.... (I knew that dunno why I asked...) ) Thanks for the lightening fast help!by DanielG - Repetier
Re: Motors off? - 12 years ago
repetier Wrote: ------------------------------------------------------- > Do you have "Go to dispose area" in your printer > config in host enabled? If yes, this move is done > after your end-Code which reenables the motors. I > should really add a motor off button there, too:-) Yes i did. Thanks!!! motor off would be great! also it would be cool to have an option to NOT add theseby DanielG - Repetier
Motors off? - 12 years ago
First thing I would like to say it (again) Thanks for your hard work on this host/firmware... Its by far the best!!!! now to the question: When I add the motors off command to the end of my parts it does not seem to work in repetier for some reason. It works fine in pronterface... any thoughts? I use the auto-fan code in sprinter and would really like to get the "all motors off command" to workby DanielG - Repetier
Re: Need more Heat Man! Heated Bed issues. - 13 years ago
yea its a pain that's why I use a heater pad with aluminum plate... back to your problem... if you have the means test the pcb separate with a higher voltage.. Alot of people with your problem separate (if you have the means) the bed voltage and crank it to 16 or so... I have a pcb and have toyed with it with glass but find the aluminum plate better....only diff is the plate has more mass.. thatby DanielG - General
Re: Why is this happening to me (dragging PLA when printing bigger ground fill) - 13 years ago
Is your print surface flat? usually aluminum prints beds are uneven unless you are using tooling plate (around 1/4 thick) If you continue to have problems with your hotend you could try a makergear.. I use them and they work great!by DanielG - General
Re: Repetier Firmware and Host - 13 years ago
Great! thanks!!!!! I really dev for this continues as it is fantastic!by DanielG - Firmware - experimental, borrowed, and future
Re: Repetier Firmware and Host - 13 years ago
First I would like to say thanks! great host! Fantastic! I do have a question...when adjusting slic3r setting I have not way to "save" the setting.. I assume maybe its a graphic glitch? BUT I have tried 3 diff pcs with the same result... So I am stuck with the default setting for now... Thanks! BTW this is what i see:by DanielG - Firmware - experimental, borrowed, and future
Re: Why is this happening to me (dragging PLA when printing bigger ground fill) - 13 years ago
Type of machine Type of extruder + extrusion temp Type of headed bed + temp Extrusion rate in firmware could help. Oh here's one thing to try as well... sand your tape with very fine paper and clean with acetone.by DanielG - General
Re: Anyone Have BotMill Feedback? - 13 years ago
For the love of GOD I hope you didn't mean this......."I sincerly hope that what Camiel is doing over there becomes a common practice." Mendel parts has been doing VERY bad things to people for 6-8 month's now or longer.... For any newbie out there reading this..stay away from the following: Mendel-parts Botmill Techzone The above three will not nothing but cause loss of money, frustration anby DanielG - General
Re: Why is this happening to me (dragging PLA when printing bigger ground fill) - 13 years ago
Try turning up your feed rate in the firmware. Plz provide complete specs of your system Danby DanielG - General
Re: How is Mendel-parts still in business? - 13 years ago
glrra19 Wrote: ------------------------------------------------------- > ok now my card says ive been credited $765 > that is alot less than the $896 that i paid. > so basically, i have lost $131 because camiel wont > do his job. > im gonna try to recover more, but im not holding > my breath. This is how he steals from people.. you are NOT the only one..by DanielG - General
Re: How is Mendel-parts still in business? - 13 years ago
People really need to stay away from this clown..... he is a train wreck waiting to take you down with him... I don't care how "nice" James and his "buddies" make him sound, his action's speak MUCH louder....he can really put a damper on the excitement of a new person joining this hobby....by DanielG - General
Re: EckerTech - 13 years ago
I got my parts VERY fast and they were of great qualityby DanielG - Reprappers
Re: Heated bed woes - 13 years ago
Replace the burned FET, and fix the heater.. Its pulling to much current.. Test on your power supply/// first.. it should yank around 10A or so ... not 13+by DanielG - RAMPS Electronics
Re: How is Mendel-parts still in business? - 13 years ago
Yea for a helpful thread! Thanks for the refund! By support I meant standing by your work and product of which you do nether.... as far as: "im giving up my weekends to help people for zero money.. so if you call that zero support sure do. I really wish I had time to help everybody, but (at this time) I simply dont, so thats why we focus now on good solid manuals that include everything. Andby DanielG - General
Re: How is Mendel-parts still in business? - 13 years ago
Camiel, Thanks for finally responding... PayPal claims are the key eh? I'll keep this simple.. I don't want to call you (I tried for weeks). I do not trust you any longer. If I owned your product I AM sure I would receive ZERO support. PLEASE reply to the claim and give back the money.. THANKS!by DanielG - General
Re: How is Mendel-parts still in business? - 13 years ago
Well its now a CLAIM with paypal... the moron had the balls to cancel the order but still wont refund??? He has time to do what HE wants including basically what amounts to is internet fraud!!!!! He keeps money until you place a claim? I don't really care who says what but the guy is a FIRST class JERK>>>>>>>>>>>>>>>>>>>>>>>>by DanielG - General
Re: How is Mendel-parts still in business? - 13 years ago
Well I filed a dispute and he responded immediately! He sure is watching our money closely. what a wack job... has no time to save a customer but will protect his paypal account filled with your money!!! (not mine anymore i hope!)by DanielG - General
Re: How is Mendel-parts still in business? - 13 years ago
when are you going? I need to open my dispute today to protect myself...... I was hoping it would not come to this.............by DanielG - General
Re: How is Mendel-parts still in business? - 13 years ago
Elidor Wrote: ------------------------------------------------------- > Where is this IRC Chet or what is ? > > Can I rich Mendel parts there ?? He has not been on IRC for a very long time.. As far as I know he cannot be reached at all...not by email, phone or any other way.....by DanielG - General
Re: How is Mendel-parts still in business? - 13 years ago
Yes tell him to answer his freakin phone and return emails!by DanielG - General
Re: How is Mendel-parts still in business? - 13 years ago
I see he has plenty of time to add new things to the website but still no time for customers.......this is the oddest thing i have ever seenby DanielG - General
Re: How is Mendel-parts still in business? - 13 years ago
Another week of no communication of any kind! I guess ill wait one more before contacting paypal.... what a bummer....by DanielG - General