It is like the_digital_dentist said, with more complex prints the failure occure more. I had it with the honeycomb infill. Small fast movements.by gforce1 - Reprappers
Why do you post everything double?by gforce1 - Reprappers
Hello, Four bearings can cause binding. See alsoby gforce1 - Mechanics
take a look at this corexy :by gforce1 - General
I guess your steps for the z-axis should be 5120 and not 10240. (M8 leadscrew, 1/16 microstepping, 0,9 degrees).by gforce1 - General Mendel Topics
There is a setting in marlin (repetier) configuration.h that prevents extrusion with a low hotend temperature. Set this on zero or below your roomtemp. Just for testing.by gforce1 - General Mendel Topics
Also a kit from spain And one from polandby gforce1 - General
Lower your max feedrate in marlin for your z-axs. Also lower your homing speed in marlin.by gforce1 - Reprappers
You can also set a waiting time between two layers or a minimum layertime in your slicer.by gforce1 - General
En waarom in het engels? Je hebt ook al eens in het nederlands gepost zie: Quotegaraguido Hallo Eddie4 Kan je mij jouw beschrijving geven van het uploaden van bootloader voor de ATMEGA 1284 met een USBASP programmer . Ik heb er ook zo een en wil mijn Melzi board van mijn 3D printer , die waarschijnlijk door mezelf gecracht is wegens een foutieve com poort , terug uploaden met een nieuwe bootlby gforce1 - Dutch User Group - Archive
Z-axis: set max feedrate on 2 (standard 5). X-axis:Your endstop is on the right side, so this is the max.endstop. is it connected on the max position of your (ramps)board?by gforce1 - Prusa i3 and variants
I use one M8 leadscrew and two 12mm smooth rods with 4 linear lm-bearings.by gforce1 - CoreXY Machines
Have you calibrated your amount of extruded filament and your axis? See:by gforce1 - Printing
Search on thingiverse egby gforce1 - General Mendel Topics
Ik kan mijn prints (abs) altijd van het kapton (rol: 20cm breed) krijgen als het bed ongeveer tot 60 graden is afgekoeld. Soms wel met de nodige kracht, het kapton scheurt eigenlijk nooit. Nieuw kapton plakken doe ik met een beetje zeepsop op de spiegel en dan met een bankpasje de luchtbellen er uit wrijven.by gforce1 - Warmtebed en Printbed
Why would you lift the carriage with belts, x and y rods and two motors? lowering only the heatbed is much easier.by gforce1 - CoreXY Machines
when your having M5 for the z-axis with 1/16 microstepping and 1.8 degrees motors your steps/mm must be 4000 see: Lower your max feedrate for the z-axis from 5 to 2.by gforce1 - General Mendel Topics
Calculate your steps/mm here and put the value in config.h in marlin.by gforce1 - Reprappers
QuoteGRAYWOLF Is there something in the G-code that could cause this? No. I think you have a problem with the direction off your axis. Or at least one off them When you press + 50 mm for x-axis is the carriage moving to the right? When you press + 50 mm for y-axis is the heatbed moving towards you ?by gforce1 - Printing
Have you calibrated your axis (x,y and z) and tested them? Eg. 100 mm movement with pronterface is actual 100 mm. Extruding not to much filament? Measured the filament diameter and calibrated the extruded length? What is your layerheight?by gforce1 - Reprappers
Have you allready changed the thermistor? I had the same problem with my hotend thermistor, but only when printing.by gforce1 - Projekte
Try set the vref on the stepper a little bit higher. Lower the z-axis speed and acceleration in marlin.by gforce1 - Printing
@ MindRealm Don't you have any problems with the z-nuts falling out? You have your x-axis ( motormount and idler) upside down. Hans.by gforce1 - Printing
I guess one of your axis (y-axis?)is going the wrong way. What printer do you have? Edit: also mirrored printsby gforce1 - Printing
Looks like a loose wire or contact. It is impossible to get those temperature leaps in such a short time. Sorry for the english, my german writing is not that good. Hans.by gforce1 - Projekte
Met die snelheid ben je dus ruim 1000 uur bezig om die 200kg te verwerken.by gforce1 - Projecten
20 Amp is enough for a printer with heatbed and only one hotend. Have you measured the voltage on the heatbed?by gforce1 - General Mendel Topics
Setz mal die geschwindichkeit fur die z-achse in marlin herunter. Hans.by gforce1 - Elektrik & Elektronik