Show all posts by user

Re: MKS TFT28 english manual? - 9 years ago

Because MKS TFT28 V1.3 is out!!

Re: New 32 bits ARM MKS Robin with TFT?? - 9 years ago

Quotegrimlok2000 Makerbase official Aliexpress shop All ordered on link above was delivered in less than 10 days.Nice and safe packing, fast replay and respond when you need help, My Robin is connected and working fine, Lucky you!!! where you are located? i'm in Canada and still waiting ... last updated was on Oct 28 for the Sbase and the Robin was Nov 04....:-(

Re: New 32 bits ARM MKS Robin with TFT?? - 9 years ago

:-( I was the first one to discovered the board, and the fifth in purchase it from TaoBao, but still waiting my board to arrive after long issue with the shipping and finally got it shipped out thanks to the intervention from Aliexpress' Ms Zhong still waiting my Sbase board as well...... sad now..

Re: troubleshooting with TFT28 V1.2 - 9 years ago

Quotemajurca Updated for firmware 1.1.4, all graphics/buttons available Great work and thanks for sharing!!!

Re: troubleshooting with TFT28 V1.2 - 9 years ago

there is not step by step. just download from the github the right version of the firmware onto the SD card's root and that's all MKSTFT_V1.1.5_English is what you needdirect to the folder

Re: P802M Prusa i3 Unofficial Support Thread - 9 years ago

Quotesiblues Well with a lot of help from a good friend it's up and running.I just wanted to ask about leveling the bed.I have seen a few videos on everyones own version of the right way to do it.I just have one question regarding the sensor on the extruder.The sensor comes in contact with the bed before the actual nozzle.I can adjust the sensor up and down but it will take a little dissasembly t

Re: New 32 bits ARM MKS Robin with TFT?? - 9 years ago

Quotechris33 I've been on the maker base site and doesn't have this board on their site and not on the aliexpress shop they have so its hard to know what it supports I went to their chinese site and github and it is there. I think they just lunched this board. it is just put on Aliexpress but with very poor info there comparing the one found in taobao.com Yes, it is a closed source, but I believ

Re: P802M Prusa i3 Unofficial Support Thread - 9 years ago

try to adjust the hot bed screws to start with. Follow the instruction given by the mfg on how to level the bed. Or search in YouTube to see Tom's video. It is the first thing you would have to learn after you assembled the printer. Then a lot of reading! Use the search to find topics of your issue or doubts. Cheers

Re: New 32 bits ARM MKS Robin with TFT?? - 9 years ago

Re: New 32 bits ARM MKS Robin with TFT?? - 9 years ago

New 32 bits ARM MKS Robin with TFT?? - 9 years ago

Just saw a "NEW" card from M K S Have anybody saw this or have ordered?

Re: BIQU MKS SBASE Help - 9 years ago

Have you tried to seek info from MKS's GitHub ? You might want to also go to thread of MKS SBASE 32 bits smoothie compatible from China

Re: P802M Prusa i3 Unofficial Support Thread - 9 years ago

QuoteScottyBoyo im not sure if this belongs here but my machine is a Pursa I3 Pro so ima put it here I added a bed leveling sensor to my Printer and enabled all the Auto bed leveling code but the safe homing feature doesnt seem to work when homing the machine it just goes to the end of the bed and then goes down and with no end stop it just hits the bed and keeps trying to go down the safe homi

Re: P802M Prusa i3 Unofficial Support Thread - 9 years ago

hahaah.... same here... I have a 5 years old and my time is "all" about to be 5 mins to 25 mins then after the little one goes to bed.... I totally get that!!! happyt wife ....happy print lol cherrs

Re: P802M Prusa i3 Unofficial Support Thread - 9 years ago

Hum mm I have never ever got that! Try to adjust the pressure from the screw that pressure the gear. It should be strong but not that strong....... The sweet spot And good luck!

Re: TB6600 4A steeper motor drive : what controller? - 9 years ago

Great info DC!! Thanks for taking the time to reply back!!! Yes , they are expensive for grl. Consumers. They are all over in the robotic industry running with all sort of application and field.

Re: TB6600 4A steeper motor drive : what controller? - 9 years ago

Thanks DC42, I can see that. It all comes down what I want as print quality, speed ... One thing that still puzzles me is why we can not run our printer directly from a PC... Without a secondary brain.... Since the PC is so powerful this days, why there's nothing out there that you can just connect PC to stepper driver...... I guess, it is about the cost of developing such SW, HW that we won't be

Re: TB6600 4A steeper motor drive : what controller? - 9 years ago

Well, may be I didn't digg deep. The Ramps could run it... Found the post from Italian forum! .

TB6600 4A steeper motor drive : what controller? - 9 years ago

Dear all, I am planning the build of my second printer Cartesian replicator type. Since I am planning to use some automation scraps from my work, I would need to RN my X and Y most likely with Nema23. The DRV 8825 or 4289 are out of equation, so I am seeing the affordable eBay TB6600 4A stepper driver. The controller that I have on hand are Melzi and Ramps 1.4 since Melzi. Melzi is out, then

Re: P802M Prusa i3 Unofficial Support Thread - 9 years ago

Quotebitslapper QuoteBobyni Bitslapper, definitely you would need to adjust the Z off set!!! You are away from the bed and that's way there isn't enough "pressure" from the nozzle to "compress" the extruded plastic. Eg.02mm resolution, nozzle 0.4mm then the nozzle should start not at Z=o rather Z=0.2 . But when using the Sensor, the sensor is higher ( further) than the nozzle you would need to

Re: New MKS SBASE Smoothieware-compatible board from China - 9 years ago

By adding a pull down in smoothie

Re: New MKS SBASE Smoothieware-compatible board from China - 9 years ago

Thanks for sharing

Re: New MKS SBASE Smoothieware-compatible board from China - 9 years ago

great sharing! Thanks

Re: Solution trouvé aux endstop optique sur MKS SBase 1.3 - 9 years ago

Quoteflyway97 hello, do you mean the endstop doesn't work? He meant he has found the solution for the optic end stop to work.

Re: Solution trouvé aux endstop optique sur MKS SBase 1.3 - 9 years ago

Bravo! Merci bien de voter contribution! je passerais voter solution a Des outer membre anglophone.

Re: P802M Prusa i3 Unofficial Support Thread - 9 years ago

Bitslapper, definitely you would need to adjust the Z off set!!! You are away from the bed and that's way there isn't enough "pressure" from the nozzle to "compress" the extruded plastic. Eg.02mm resolution, nozzle 0.4mm then the nozzle should start not at Z=o rather Z=0.2 . But when using the Sensor, the sensor is higher ( further) than the nozzle you would need to let the board to know that

Re: P802M Prusa i3 Unofficial Support Thread - 9 years ago

Quotebitslapper I got the sensor working . Now i just need to get it as close to the head z position as possible as my prints were coming out crappy and not sticking since the head was way too high. I was messing with the position last night and got way too over zealous as the head smashed into the bed and proceeded to drag in the x dir -_- ... luckily i had blue painters tape on so it softene

Re: P802M Prusa i3 Unofficial Support Thread - 9 years ago

Aluminum Bed Plate.... Dear all, I believe the new Zonestar P802N has a aluminum plate for the hot bed. Would you please confirm? I've tried to contact Zonestar, but no answer yet from them. basically, our 802M model which is all acrylic and 6mm thickness, would not stand high temp when printing ABS for log/big prints. Mine was deformed, due to high temp plus electronics failure. I think it w

Re: P802M Prusa i3 Unofficial Support Thread - 9 years ago

I connected only the Sig When open =o When triggered = high ( 4.6V) When testing, have your Z up to the middle of the frame, then tray to home all, and have handy a piece of metal ( screw driver would work). If z is coming down try to trigger the sensor. I always have my finger on the power off switch, just in case it goes too deep and hit the bed.. Etc.... Good luck

Re: P802M Prusa i3 Unofficial Support Thread - 9 years ago

Quotebitslapper Now I just need to get my inductive sensor to work -_- . Seems it's not getting power... Mine takes power directly from the PSU. 12V Then reduced using resistors Signal gets about 4.3v And it is connected to Sig pin One pin for the Z gets connected! Dbl check your grill of probing! Good luck