Quotewidespreaddeadhead QuoteDnixon123 Right now I'm using white PLA... My stock extruder jammed on Hatchbox White PLA, and I've since changed to an e3d lite 6 hotend and have had zero issues with clogs. A lot of people were mentioning this to me, but at the time I didn't really think it was necessary to spend more money on something. Eventually I ordered the e3d lite6, installed it and have beeby Dnixon123 - Prusa i3 and variants
Quotewidespreaddeadhead QuoteDnixon123 Quotewidespreaddeadhead QuoteDnixon123 Over the past few days I've been having some issues with the extruder on my printer. It will staart making a skipping noise and the filament will get caught. I've fixed it several times by opening up the extruder and removing the mangled and squished piece of filament but it keeps happening. I think that the extruder isby Dnixon123 - Prusa i3 and variants
Quotewidespreaddeadhead QuoteDnixon123 Over the past few days I've been having some issues with the extruder on my printer. It will staart making a skipping noise and the filament will get caught. I've fixed it several times by opening up the extruder and removing the mangled and squished piece of filament but it keeps happening. I think that the extruder is the issue but it could also be the filby Dnixon123 - Prusa i3 and variants
Over the past few days I've been having some issues with the extruder on my printer. It will staart making a skipping noise and the filament will get caught. I've fixed it several times by opening up the extruder and removing the mangled and squished piece of filament but it keeps happening. I think that the extruder is the issue but it could also be the filament that I'm using. It's the cheap haby Dnixon123 - Prusa i3 and variants
QuoteVanbot QuoteDnixon123 I got my end stops working, I reset the x end stop pins to the z max end stop pins in marlin. The printer is now working and I'm getting ready to start my first print! Hope it goes well. Thanks! I really appreciate the help!by Dnixon123 - Prusa i3 and variants
I got my end stops working, I reset the x end stop pins to the z max end stop pins in marlin. The printer is now working and I'm getting ready to start my first print!by Dnixon123 - Prusa i3 and variants
QuoteSteveRoy QuoteDnixon123 QuoteVanbot I had the same problem with my Folger build. Their manual has some errors in it. Try moving the X end stop plug onto the set of end stop pins on RAMPS that is second from the bottom. The Folger manual says to use the bottom-most pins but that position is for a Min end stop. Because Folger puts their X end stop on the right side of the printer it is actualby Dnixon123 - Prusa i3 and variants
QuoteVanbot QuoteDnixon123 I'm having some serious trouble getting the printer homing configured. It's only the x-axis that I'm really having problems with. I followed the build and configuration instructions from Folger Tech so I have my x end stop to the right and I have my marlin and repetier host set how they recommended. Without changing anything, the x-carriage slides to the left but doesn'by Dnixon123 - Prusa i3 and variants
I'm having some serious trouble getting the printer homing configured. It's only the x-axis that I'm really having problems with. I followed the build and configuration instructions from Folger Tech so I have my x end stop to the right and I have my marlin and repetier host set how they recommended. Without changing anything, the x-carriage slides to the left but doesn't stop at the end stop. I'vby Dnixon123 - Prusa i3 and variants
I just got the rev B kit and I'm having trouble with the end stop on the y axis. There are no bearing holders for the switch to contact like in the rev A kit. I can't seem to figure out a way to mount them, how did you guys do it?by Dnixon123 - Prusa i3 and variants