Weird issue that I can't seem to figure out. I have auto bed leveling working on my Folgertech i3 2020 and my start code has G28, G29. Prints are coming out beautifully, but for some reason when using Repetier my printer decides to do another G29 after the print. Most of the time this causes the servo arm to bend/smash my print. This doesn't happen in MatterControl, but I prefer Repetier for now.by nmh5028 - Prusa i3 and variants
Weird issue that I can't seem to figure out. I have auto bed leveling working and my start code has G28, G29. Prints are coming out beautifully, but for some reason when using Repetier my printer decides to do another G28 after the print. Most of the time this causes the servo arm to bend/smash my print. This doesn't happen in MatterControl, but I prefer Repetier for now. I have checked my end coby nmh5028 - Prusa i3 and variants
[email protected] I can get it "working" by changing settings or pin plug-ins. But what I can not figure out is why when I hit Y or Z they home like they should but the X just marks where ever it is sitting as the new "home" location. I've gone through the whole thread and I'm in exactly the same place as you. I just flashed the firmware linked a few posts ago and it does the same thiby nmh5028 - Prusa i3 and variants
INteresting, wonder if there is an issue with the Folgertech firmware. This is my log when connection to the printer in Reptier. Lots of errors but I'm not sure what they mean. Also, the RAMPS test code runs fine, so I'm pretty sure FOlgertech has an error in the config, but I'm not sure how to troubleshoot that. 15:38:09.066 : Printer reset detected - initalizing 15:38:09.066 : start 15:38:09.0by nmh5028 - Prusa i3 and variants
Ok, so I'm a few steps closer than earlier after a lot of troubleshooting and part replacement. I have my Y and Z axes working properly, but my X will not do much. If I push home, it moves a few mm and stops, then sets that position to 0. If I move it in the other direction, no matter if I command 1mm, 10mm, or 50mm, it moves the same few mm and stops. I can only move it each direction 1 time andby nmh5028 - Prusa i3 and variants
Quotego_gn Have you installed the stepper driver boards properly? In the right orientation? Yes, the adjustment screw is facing away from the power connections as in the photo in the build guideby nmh5028 - Prusa i3 and variants
Quotemarkts So you "homed everything" manually by pushing the extruder to the stops? They didn't move when pressed the home button? Yes and yes, I tried pushing the Home button in the software and nothing happened (X and Y axis). I then moved the Y axis to the home position (at the end stop), and couldn't get it to move either direction. There is no sound or anything from the motorsby nmh5028 - Prusa i3 and variants
Hey everyone, I just finished assembling my i3 2020 and I am having an issue controlling it. I am new to this so I;m not sure exactly what to do. When connecting to Reptier, I can heat the bed and extruder, but I can't get any of the motors to move. I have homed everything and still no luck. It looks like the commands are sent and received, but there is no response from the printer. I have followby nmh5028 - Prusa i3 and variants
I'll give that a read, but that doesn't sound like it would solve the issue of losing USB connection with 4 or 5 of the stepper drivers installed. My PC can detect it with 2, 2, or 3. If I add the 4th it connects and immediately disconnectsby nmh5028 - Prusa i3 and variants
Just finished assembly of my Folger Tech Prusa i3 2020 and I'm not having any luck getting the motors to move. Wiring has been check and rechecked multiple times, and is fine. There are a few signs that something is wrong, but I'm new to this and don't know where to start troubleshooting. 1. I lose my USB connection to the Arduino if I connect more than 3 of the stepper drivers to the RAMPS 2.by nmh5028 - Prusa i3 and variants