Guys, thank you very much) Everything worked out and works))))by kasper - Firmware - experimental, borrowed, and future
Quotegloomyandy It looks to me like you are connecting to at least one of P0_15, P0_16, P0_17 via the pins in EXP1, don't do this, use the pins on J7 (you are already doing this for two of the pins, but I can't tell from the photos which ones), you basically want all three of those connections to go to J7. If you are still having problems please take some more pictures that show the connectionsby kasper - Firmware - experimental, borrowed, and future
Quotejay_s Maybe you could try reflashing the ESP software based on PCR's instructions Yes I've tried it once or twice )by kasper - Firmware - experimental, borrowed, and future
Quotejay_s Theres a typo on the wiki Please change it to lpc.board = mkssbase_1.3 checked, replaced... didn't help )by kasper - Firmware - experimental, borrowed, and future
to the root of the /sys folderby kasper - Firmware - experimental, borrowed, and future
SENDING:M122 P200 == Configurable Board.txt Settings == lpc.board = generic leds.diagnostic = 1.18 stepper.enablePins = { NoPin NoPin NoPin NoPin NoPin } stepper.stepPins = { NoPin NoPin NoPin NoPin NoPin } stepper.directionPins = { NoPin NoPin NoPin NoPin NoPin } stepper.digipotFactor = 0.00 stepper.TmcUartPins = { NoPin NoPin NoPin NoPin NoPin } stepper.numSmartDrivers = 0 heat.tempSensePins =by kasper - Firmware - experimental, borrowed, and future
Power is connected to the Vin on Wi-Fi on Sbase to the 5v pin in the EXP-1 connector board.txt // Board Hardware configuration file for MKS Sbase 1.3 // generated by RepRapFirmware Configuration Tool (LPC Version) v2 // on Tue Jun 02 2020 09:07:48 GMT+0300 (Москва, стандартное время) //Note: Each line should be less than 120 characters. // : Unwanted options can be commented out or set toby kasper - Firmware - experimental, borrowed, and future
It seems to have done everything as in an article on GitHubby kasper - Firmware - experimental, borrowed, and future
Good day. Tell me about this error. >>> M552 S0 SENDING:M552 S0 WiFi module started Error: Failed to initialise WiFi module, code -7 Error: Failed to initialise WiFi module, code -7 MKS Sbase v1.3 I did everything just like hereby kasper - Firmware - experimental, borrowed, and future
the fact is , Sanguino loader size is very large , so do not have enough memory . I was not able to solve the problem is not asking loaderby kasper - Prusa i3 and variants
Hey. I gathered here a programmer to LPT . You need to alter the boot loader is obligatory ( referred to above is written ) . The fact that you have flashed boot loader and takes a lot of memory to Atmega , therefore gives this error . just do not have enough memory for firmware . Now I have a programmer ) ) ) ) ) ) ) I have everything turned out) ) )by kasper - Prusa i3 and variants
good afternoon. I had a problem that after flashing all axes motors move only in one direction. the thing is that you need to flash the right loader . after I flashed right loader and native firmware , I have all earned the right immediately . The loader of Sanguino is not correct . here's the link will have everything that you need to solve the problem firmware for use arduino-1.0.6. I apologizby kasper - Prusa i3 and variants
Quotejfd Hi, - Marlin source code - Update Utility - Firmware hex with auto level (I have compiled a version without auto level) - Documentation THX. Very useful information . But everywhere I see uses proximity sensors , and I would like to connect a servo , which he had hidden , and took out a trailer .by kasper - Prusa i3 and variants
Hello friends. something like I read a forum (with English bad-I) and realized that ABL do with the sensor. And who do probyval ABL with servomotor. (No sensor and servo available) Can knows where to connect? Printer P802M. Melzi 2.0 1284P Reprap Control Maynboard THXby kasper - Prusa i3 and variants