Quotebogaskilop I sorted out this connections i used MISO MOSI SCK from ISP1 connector my three tmc2130 (CS pins for x y z ) are connected to D14 D30 D31 on EXP3 ( needed to add CS pin to rumba board at section steppers). also Endstops are connected to TMC2130 so sensorless homing works ---------------- | | DIR | | STby crumb4life - RAMPS Electronics
I built the D-bot from Works great. Recently I added a proximity sensory or Auto Level also works. However when I home the Z it will not move to the center of the bed. It will home in the back left corner of the bot. Now If I swap the X and Y motors and switch Y to a min stop versus a Max stop. It will home in the center of the bed no problem Buit all my prints are facing backwards( not the enby crumb4life - CoreXY Machines
I would suggest using the beta firmware located here Start with that. QuotePonyTailSteve Quotecrumb4life QuotePonyTailSteve Hello, So I got my FT 2020 i3 built and printing; however I do have a couple of issues that I am unsuccessful so far in resolving. 1. It prints in a mirrored fashion. Meaning the resulting print is that exact mirror of what the original is. I can resolve this in the Reby crumb4life - Prusa i3 and variants
QuotePonyTailSteve Hello, So I got my FT 2020 i3 built and printing; however I do have a couple of issues that I am unsuccessful so far in resolving. 1. It prints in a mirrored fashion. Meaning the resulting print is that exact mirror of what the original is. I can resolve this in the Repitier Host by selecting the "mirror" button, but really would like to permanently fix it. I did some searchiby crumb4life - Prusa i3 and variants
QuoteNeverdone Quotetjnamtiw QuoteNeverdone I have been running my printer now for about a year and half. LOVE THIS THING! But I am gearing up to do some upgrades. I want to start with auto bed leveling, I have printed a few pieces, servo mount and arm, but I am coming up short on where to go to find the code on how to do this or maybe a how to. Can anyone help me out? This will fit your 202by crumb4life - Prusa i3 and variants
QuoteDynamiteHack Quotecrumb4life Amazon has plenty of boards available through Prime if you want to go with what came with the printer.. Have you purchased boards from Amazon. If so, any vendor recommendations?? Prices are good but some of the reviews are troubling. Heated beds seem to be problematic for the cheap clones. Not sure I want to learn how to change MOSFETs. Well funny thing is eveby crumb4life - Prusa i3 and variants
Quotetjnamtiw QuoteMendingThings So I have been using my F/T 2020 i3 for quite some time now and I don't know why I didn't think of this question before but here it is anyway. Since our height limit is the carriage contacting the motors, which by the way, I have upgraded to the motor extensions, why do we have the hot end mounted so far low below the carriage? If we were to raise it up to just bby crumb4life - Prusa i3 and variants
Amazon has plenty of boards available through Prime if you want to go with what came with the printer.by crumb4life - Prusa i3 and variants
After flashing the Firmware like 40 more times I finally got it to work proper. I don't know why it wasn't working the first flash. But now it is. On to the next problem.by crumb4life - Printing
Not sure what happened but recently I upgraded my X axis to a V-Slot from a bearing style. It has been working and printing fine. This morning I went to print something and it behaves very strange. When printing the perimeter it will come to nearly a stop before changing directions.And when not printing and moving to print again slow as heck. I am not sure why as it was fine below are my acc andby crumb4life - Printing
I have a folger tech i3 2020 that I recently setup auto level on. I have a micro switch and I have the unit probing in 4 fours and the offsets on the hot end are within .2mm prints are turning out very good from this. However even though I centered the object in cura the prints are not centered they are printing far right as if that is the center. I am not sure what is the cause of this. I have aby crumb4life - Mechanics
Quoteiamquestar Quotecrumb4life Can someone help me and tell me what is wrong has my prints move up they seem to be getting smushed at the top closer to the base they are fine(minus the poor bed adhesion on this one) Printing in PLA at 195c. I am kind of lost on what this could be. I have checked my Z steps and they are moving in the right increments. It looks to me to be a temp issue. PLA needby crumb4life - Prusa i3 and variants
Quotetjnamtiw Quotecrumb4life Quotemfisch The mega would show under Devices and printers in control panel for windows.Since your manual control was via the computer, it is seeing the mega.Maybe your comm settings are off and you are dropping characters or commands. It seems like mine is dropping characters or commands. I will have to try using the sd card.The Pi came in so I have been trying toby crumb4life - Prusa i3 and variants
Quotemfisch The mega would show under Devices and printers in control panel for windows.Since your manual control was via the computer, it is seeing the mega.Maybe your comm settings are off and you are dropping characters or commands. It seems like mine is dropping characters or commands. I will have to try using the sd card.The Pi came in so I have been trying to get that setup with Octoprint.by crumb4life - Prusa i3 and variants
Can someone help me and tell me what is wrong has my prints move up they seem to be getting smushed at the top closer to the base they are fine(minus the poor bed adhesion on this one) Printing in PLA at 195c. I am kind of lost on what this could be. I have checked my Z steps and they are moving in the right increments.by crumb4life - Prusa i3 and variants
Quotetjnamtiw Quotecrumb4life QuoteMach Make sure your X axis endstop is plugged in one spot over from the right on your ramps board. Manually press the X axis endstop, and type m119 into the gcode bar under manual controls. What does to command log say when you do this? Can you copy and paste your config.h file in pastbin and give a link to it. Also, can you take a screen snippet of you printerby crumb4life - Prusa i3 and variants
QuoteMach Make sure your X axis endstop is plugged in one spot over from the right on your ramps board. Manually press the X axis endstop, and type m119 into the gcode bar under manual controls. What does to command log say when you do this? Can you copy and paste your config.h file in pastbin and give a link to it. Also, can you take a screen snippet of you printer shape setting in repetier. Thiby crumb4life - Prusa i3 and variants
Just built my i3 got it printing today. After I borrowed a ramps board from a friend, mine is bad. I am printing a test print now which is working. But I can't seem to get the X Axis to home. I hit home in Repetier and it doesn't move to the right where the end stop is. Any suggestions I can try?by crumb4life - Prusa i3 and variants
Sorry wrong forums to post this.Please delete.by crumb4life - Prusa i3 and variants