Quotekd6hq Currently I'm using Marlin 1.1.0 - RC6 for a printer that I have attached a Laser to. I have been using M106, M107 and D9 (connection) for laser on, off and power control. I see that in Marlin 1.1.8 M3, M4 and M5 have been set up for spindle / Laser control. Is there any advantage of M3, M4, M5 over using M106/107? I know that I would need to switch to a 5V PWM pin but is theby mstitdk - Firmware - Marlin
and the reason why I don't use: #define E0_AUTO_FAN_PIN -1 //er lig med linje:208 i pins_ramps.h #define E1_AUTO_FAN_PIN -1 #define E2_AUTO_FAN_PIN -1 #define E3_AUTO_FAN_PIN -1 #define E4_AUTO_FAN_PIN -1 #define EXTRUDER_AUTO_FAN_TEMPERATURE 50 #define EXTRUDER_AUTO_FAN_SPEED 255 // == full speed Is that I S3D use M106 to controle fan speed when bridging and other stuff. unlessby mstitdk - Firmware - Marlin
Is is posible to code that FW turn on a fan on a custom pin when extruder is above 80 degrees or something like: #define EXTRUDER_AUTO_FAN_TEMPERATURE 50 #define EXTRUDER_AUTO_FAN_SPEED 255 // == full speedby mstitdk - Firmware - Marlin
Error: you cannot set extruder_0_auto_fan_pin equal to fan_pin This is caused when you try to, as the error message states, set the EXTRUDER_0_AUTO_FAN_PIN in Configuration_adv.h to the same pin as FAN_PIN in the respective pins file. For the purposes of this particular guide, the specific pins file we’re looking at is the pins_RAMPS.h file. Before addressing the fix, let’s look at the cause.by mstitdk - Firmware - Marlin
#define CONTROLLERFAN_PIN 7 //Pin used for the fan to cool controller (-1 to disable) #define CONTROLLERFAN_SECS 50 //How many seconds, after all motors were disabled, the fan should run #define CONTROLLERFAN_SPEED 255 // == full speed that part work tested OK what about the #define E0_AUTO_FAN_PIN 9 then i get this error: exit status 1 #error "You cannot set E0_AUTO_FAN_PIN equal to FAN_PIN.by mstitdk - Firmware - Marlin
i have this one // // Heaters / Fans // #ifndef MOSFET_D_PIN #define MOSFET_D_PIN -1 #endif #ifndef RAMPS_D8_PIN #define RAMPS_D8_PIN 8 #endif #ifndef RAMPS_D9_PIN #define RAMPS_D9_PIN 9 #endif #ifndef RAMPS_D10_PIN #define RAMPS_D10_PIN 10 #endif does the -1 be 7?by mstitdk - Firmware - Marlin
QuoteDust "you migth also help me with a nother issue, is that the fan on hot-end is off the first two layer, is there som where with in the marlin FW something that control that" no, that is a slicer setting. Slic3r or cura, or what ever your using. i found that back to subject i get this error now exit status 1 #error "You cannot set E0_AUTO_FAN_PIN equal to FAN_PIN. #define CONTROLLERFANby mstitdk - Firmware - Marlin
QuoteDust The fan needs to be connected to a output with a mosfet from your options are d7,d8,d9,d10 Do you have anything in d7? If not plug the fan into d7 set #define CONTROLLERFAN_PIN 7 thx a lot for your answer, that solution have crossed my mind, but i was unsure on that. you migth also help me with a nother issue, is that the fan on hot-end is off the first two layer, is there somby mstitdk - Firmware - Marlin
Hello i will try again, under this sub cat. what pin do i add for the code below this, to control the fan on a MKS Gen v1.4, i would like to yse the 12 to 24 voltage out put on the board //This is for controlling a fan to cool down the stepper drivers //it will turn on when any driver is enabled //and turn off after the set amount of seconds from last driver being disabled again #define CONTROLby mstitdk - Firmware - Marlin
CLOSED, i got it by my self.by mstitdk - Firmware - experimental, borrowed, and future
I got it to Work after all, it was display that have some defects, i got a new one, and now it wotk. Thx for all the helpby mstitdk - Firmware - Marlin
Hello I have bougth a MKS Gen v1.4 controller for my Creality Afinibot A9 with TMC2100 motor driver, and what a change in noise level. but i have some issues that i cant figure out or know how to solw, and tried for two days now on other forums and people my power supply is on 24v,and i have 24v fans connected on D9 and the AUX 12 to 24v out put on the board. does any one know how to control fby mstitdk - Controllers
QuoteGRAYWOLF Have you enabled it in the firmware before up loading the firmware? I think you need to remove the # on the opproate line to enable it. i dont think that you know what you are talking about...! so you suggest that i put in "define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER" on line 560 intered of "#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER"by mstitdk - Firmware - Marlin
Hello any one that have the newste marline firmware custome made for a Creality 3D Afinibot A9 printerby mstitdk - Firmware - experimental, borrowed, and future
Hello i have some very wird issus. First i have a Creality 3D Afinibot A9 printer, it is a very fine one, and it fit my need. i have now startet to add some extensions on it. the first thing is that i have a full graphic smart controller, and not matter what i do, i just cant cant that display to show anything. things that i have tried: - uplaode std firmware -- turned arround the cable - uploby mstitdk - Firmware - Marlin