Just finish a print and it's just so wavy I put back my sbase 1.3 on my D-bot with external TMC2208 on XYZ and DRV8825 for E the current I set to 480mA for XY and 780mA for Z, after this print I increase the current on XY to 700mA but the wavy is still there. I enabled linear advance with K value at 0.1 JUNCTION_DEVIATION_MM 0.022 or should I use Jerk? enabled S_CURVE_ACCELERATION Other paramby Keshan - General
I put the extruder motor to other positions, XYZ, all work fine, so that I can rule out the possible damage of the particular motor and no it won't move on both direction if I put it back on E0, I saw some people in facebook group had the same problem, an LV8729 or older Marlin solved the problem. unfortunately old Marlin didn't help in my case, I ordered some LV8729 see if it will work.by Keshan - General
I am not sure if I fully understand your question, my wires are red-blue-green-black from left to right just like my other 3 motors.by Keshan - General
I am using SKR V1.3 with 4 TMC2208 in UART, X, Y, Z all work well and home correctly, when I was trying to do extrusion calibration tonight, I found that my E motor doesn't move at all. I disabled/comment out the cold extrusion prevention. steps I've tried so far to narrow down the problem: swap the E TMC2208 to Z and Z works fine. swap the E motor to Z and when I home Z, the E motor turns uby Keshan - General
thanks Dust, after a long talk with the seller, they rule out the firmware fault (by sending me a firmware they configured and believed it's correct) , and we agreed that the problem could be from hardware, so they are sending out a new replacement board, what a lucky day, they sell thousands of boards all year long and I get a lemon.by Keshan - General
I finally get ready to upgrade my printer and found out that my X+ is always triggered. The board I am using is an SKR v1.3 and the end switches I am using..... well it's really irrelevant, I tried different types of switches on X+ and nope they are all stuck at triggered (not because I set the logical wrong in marlin). The same happens to X- Y-, so only Y+ Z- and Z+ works fine, but I really needby Keshan - General
I started to assemble my delta printer today and only find out that the sense voltage on X+ X- and Y- endstops are only about 3.1v where the Y+ Z- and Z+ are 3.3V so my X is always TRIGGERED or OPEN (depends on the marlin config) and it won't change. I tried to replace the 180 ohm resistor on the optical endstop with a 100 ohm and I also tried to add a 220 ohm resistor on top of 180 ohm per theby Keshan - Controllers
Just wondering if anyone tried to run marlin 2.0 on this board, I spent the day try to make it boot, but with marlin 2.0 compiled and copied to the sd card, it just won't boot, the firmware.bin always changed to FIRMWARE.CUR, but the control board just won't boot.by Keshan - Controllers
Quotejmaurin Arthur, can you tell me from which version support for PT100 and bed leveling was fully implemented? That's the only features that I need.....so I'll try down to this version instead of latest. Note that author of issue ticket know the problem and possible solution (but Ican't tbe sure, see: ), but it doesn't want to help He is frustraded with MKS (and he is right!) and for thatby Keshan - Controllers
I am also using PlatformIO with Atom, but on Windows 10 and MacOS, both with no success I am uninstall everything and give it another go. update: it seems my pfsense blocks something.by Keshan - Firmware - Marlin
I was trying to compile marlin 2 for my sbase since last night. but I always get QuoteProcessing LPC1768 (platform: https://github.com/p3p/pio-nxplpc-arduino-lpc176x/archive/master.zip; board: nxp_lpc1768; framework: arduino) PackageManager: Installing framework-arduino-lpc176x @ >=0.0.2 Error: Detected unknown package 'framework-arduino-lpc176x' Board name: BOARD_MKS_SBASE Build type: buildby Keshan - Firmware - Marlin