Hello guys recently I faced with an issue with my 3d printer sometimes when my 3d printer is printing Z axis stop moving and my print fails can somebody help me please? this picture is one of my print wich is failedby Enzo-B - Firmware - Marlin
thank you so much bro It fixed but the problem is I can't connect to webserver control after install the new version of marlinby Enzo-B - Firmware - Marlin
the problem is with the mks tinybee board in new version of marlin beacause when I compile the marlin with other board there is no problem! I tried some ways but the error is still exist!by Enzo-B - Firmware - Marlin
Hello guys when I compile the marlin I face with this issue please help meby Enzo-B - Firmware - Marlin
thank you for your replay I checked that,It is correct the problem is only for X axis I changed the X stepper and endstop to see this problem happens for other stepper or not and It happened the problem is only for X axisby Enzo-B - Firmware - Marlin
Hi friends I have a problem with my delta,when It is homing and when X axis triggered microswitch X stepper motor start vibrating my board is skr pro and my stepper drivers are tmc2225 can you please help me to solve this problemby Enzo-B - Firmware - Marlin
thank you so much bro does mixing extruder work on cyclops hotend?by Enzo-B - Firmware - Marlin
Hi friends I want to active #define MIXING_EXTRUDER but after click on build I see this error I did what It said but error is still exist can you please tell me how can I active #define MIXING_EXTRUDERby Enzo-B - Firmware - Marlin
Hello friends I updated my printer and something that happens is,every time I turn on my printer I see this error(eeprom crc error initialize eeprom).I click reset but when I turn off the printer and turn it on again this error comes up! I used mks tinybee please helpby Enzo-B - Firmware - Marlin
Hi friends I have a mks robin nano V3.1 with ts35 v2.0 LCD,I want to install mks pwc on It but I faced with this error while mks robin nano V3.1 supports pwc module,is there any way to solve this error?by Enzo-B - Firmware - Marlin
Thanks for your explanation bro I said I have two controller,a BTT GTR V1.0 and a MKS ROBIN NANO V3 I want to use one of these controllers for my new 3d printer,I want to know which one of these controllers support both the modules(mks ups 12V & mks_pwc_module)at the same time?by Enzo-B - Firmware - Marlin
actually I want to use one of these boards,I want to know witch one can support both these module(the pictures)at the same time?by Enzo-B - Firmware - Marlin
Hi guys I have two controller,a BTT GTR V1.0 and a MKS ROBIN NANO V3 can I use ups module(power lose recovery) and auto power off after print is done module for the both boards at the same time?by Enzo-B - Firmware - Marlin
Yeah bro I remove the keying tab on the connector as you see in the picture of my previous comment Now both LCD and SD card work perfectby Enzo-B - Firmware - Marlin
The issue fixed I said It's not a hardware issue because there was 2 boards with same issue I just remove this part of wire with cutter and turn It 180 degree and It worked! thanks of all who tried to help me.by Enzo-B - Firmware - Marlin
Does anybody run 128x64 reprap discount smart controller with mks tinybee?by Enzo-B - Firmware - Marlin
thanks bro I tested that but the Issue still exist!by Enzo-B - Firmware - Marlin
It's my lcd you didn't answer me how can I be sure It is hardware issue or not?by Enzo-B - Firmware - Marlin
yes It is REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER because on ramps works fine How can I be sure It is a hardware issue or not?because I have 2 mks tiny boards with same problem!by Enzo-B - Firmware - Marlin
Is there any way to solve this issue or I lost my money?by Enzo-B - Firmware - Marlin
Thank you bro I checked that,there is connection between 2 sd card cansby Enzo-B - Firmware - Marlin
can you explain more how I test the connection between both sd card cans?by Enzo-B - Firmware - Marlin
Yes It is still flashingby Enzo-B - Firmware - Marlin
I tested that,stil black LCD Is there any setting in marlin for 128x64 reprap discount smart controller? maybe I did not active some settings!by Enzo-B - Firmware - Marlin
I bought 2 mks tinybee yesterday you mean both boards have same issue?by Enzo-B - Firmware - Marlin
I checked that and It is stable I guess It is marlin issueby Enzo-B - Firmware - Marlin