I added BLtouch and upgrade firmware. Now it looks like BLtouch doesn't work. It doesn't do nothing when I press probe, it smashes nozzle to the heatbed. I have uploaded firmware for Z homing. Connected black and white to Z switch. Printer is Ender 3 pro with SKR-mini-E3 board Any idea?by Blisk - Firmware - Marlin
there are mostly DIY but controllers support all of thatby Blisk - Prusa i3 and variants
Almost all of that clones already haveby Blisk - Prusa i3 and variants
there are prusa clones which works with prusa firmware.by Blisk - Prusa i3 and variants
Did anyone tried to install MMU2 on printer whihc is not Prusa?by Blisk - Prusa i3 and variants
Is there any 3D printer controller which is 32 bit and have extrenal stepper drivers (support TMC2208) and support marlin and multi colors printing?by Blisk - General
It is HIC printer, made from alu profiles. But it will be more like build new printer from old one, because I will change almost all. What is my major concerne is that movable parts have almost none tolerance, of shaking and vibrating.by Blisk - Mechanics
Does anybody have some close pictures of new printers like this http://www.nexi-tech.com/wp-content/uploads/2017/05/Snap-2017-05-22-at-18.36.05-1282x500.png I like to upgrade my Z and X axis with gears like this on picture. Is it possible to buy that spare parts somewhere? If not if someone have printer please put some close pictures here to see how it is build. Thank you.by Blisk - Mechanics
I have changed stepper drivers now it works OKby Blisk - Prusa i3 and variants
This is second print and it is the same don't know what happend but printer start to print a fev mm to left. (Layer Shifting or Misalignment) On second print it start to print after a while fev mm to back of Y. Any idead why this is happening? Belts are ok and tight, what else can be? I have upgraded firwmare to bugfix 1.1.xby Blisk - Prusa i3 and variants
I have manage to update marlin it is now 1.1.8 Problem is because sensor recognise heatbead but doesn't stop Z motors it continue to Z min switch. what can be wrong?by Blisk - Prusa i3 and variants
I have disabled safe_homing_z now it worksby Blisk - Firmware - Marlin
After uploading marlin 1.1.8 to my I3 printer and autobed levelling was already enabled Z axis switch doesn't work. I tested with M119 code and it say z_min: open when I press z switch it say z_min triggered. X and Y works OK. I also noticed when I press Z home in repetier, on LCD shows this G28 Z forbidden Can't find what can be wrong.by Blisk - Firmware - Marlin
How can I update Merlin?? I searched on board manufacturer for new firmware but all is dated on 2015by Blisk - Prusa i3 and variants
I am trying to upgrade my printer with filament sensor and heatbead auto level. Now with installing that on printer all goes ok, but problem is with code, with arduino, because I can not find where to change code in my firmware for that. I followed this but stuck with code for setup filament sensor. There were 2 changes needed to the pins_ULTIMAKER.h file: under the Limit Switches section, chby Blisk - Prusa i3 and variants
I have changed the whole extruder and now prints as it shouldby Blisk - Prusa i3 and variants
Thank you I checked all but still the same. Last time I tried to press filament in but it didn't go in, when I pulled out and than pushed in than it works again. I have sandisk SD card. When I check filament it is eatedout by stepper, so something stuck that fillament and it males stop to print. Filament is good quality not the cheapest one.by Blisk - Prusa i3 and variants
Is there no Alu mounting kit??? just printed one?by Blisk - Prusa i3 and variants
Can someone explain to me, how it is J-head extruder mounted on printer, I didn't find any holder or something to use to mount that on printer.by Blisk - Prusa i3 and variants
I have the same problem whe I calibrate printer and everytime when I upload firmware nothing changes. I still didn't solved problem.by Blisk - Prusa i3 and variants
NO, still not working and have no clue what can be wrong. I even raise tempereture to 208 for PLA and still the same.by Blisk - Prusa i3 and variants
It is hard enough. I have changed now stepper motor to see if it works ok.by Blisk - Prusa i3 and variants
Don't know why printer stops to print, filament just stop coming out of nozzle. Sometimes that happends after 10% sometimes after 50% of finished model. I have changed nozzle and throath and still the same, like nozzle get clogged and after that I push by hand filament in it and it works again until the same happend.by Blisk - Prusa i3 and variants
Both of them are GT2650 Will try againby Blisk - Firmware - Marlin
I have 2 of this printers and never needed to do that beforeby Blisk - Firmware - Marlin
And how to do that with arduino software?by Blisk - Firmware - Marlin
I have tried to calibrate my printer again but after uploading firmware it doesn't remember changes, it is still like before, everytime I change settings in marlin firmware nothing changes after uploading it. What can ve wrong??by Blisk - Firmware - Marlin
I have calibrated printer and it is about 0.2 mm tolerance. But still get holes distance closer together than it should be. Also I tried to prin this and and doesn't fit together especially that U part, because hole in U part is smaller than anything else which must fit in. Any advice how to solve that?by Blisk - Printing
When I print something out, holes on printed objects are always smaller and closer together than on 3D software where I draw that object. is there some compensation settings in Cura for that, so holes in printed object are the same as on drawing and distance from holes are also the same as on drawing and not 20% closer together?by Blisk - Printing
And yet holes are printed undersized. Why Slicer haven't any settings for compensation where people can set compensation parameters for holes?by Blisk - Printing