At this point I do not have a PC only iMac. I can not fine a way to update the PanelDue to 1.16 with the Mac. Do I need to pull the Due and take to to work to do on a PC? Thanks,by 3D-Print - Duet
When I try to send this command after uploading the new "DuetWebControl-1.15a.bin" to the SD card via the web interface, I receive this message: M997 S:2 Invalid module number '2' Is that expected? I am running Firmware: 1.18.1 (2017-04-09)by 3D-Print - Duet
Curious as to the advantage of this command code.by 3D-Print - Duet
Thank you, made the changes and it works perfectly with the M307 commands!by 3D-Print - Duet
I jsut updated by firmware from 1.12a-dc42 to 1.18.1 and now my PID setting are not working. I seems like my bed is using bang bang pulses vs. PID. Prior to the update, my SSR would flicker and maintain a very stable bed temp. Now it is either on or off and quite variable. Here are my M301 codes from the config file: M301 H0 P24 I0.80 D105 T0.50 S1.0 ; PID settings for Print Bed (-P means bby 3D-Print - Duet
The file I sliced with Slic3r with settings to use firmware retraction is working beautifully. I have set the retraction to 6.8 mm. Thanks, Danby 3D-Print - Duet
I can not find firmware retraction with MatterSlicer or with KISSlicer........by 3D-Print - Duet
I just looked at the print g-code after setting to firmware and I can see that the G10 does not define the amount, thus to answer my own question, this should mean that the only retraction that will occur is defined by M207by 3D-Print - Duet
More specifically, will the print gcode retraction only apply to the active tool, and the M207 to all my active and mix enabled tools?by 3D-Print - Duet
Awesome. I just found the firmware retraction check box in Slic3r. Does this mean that retraction (e.g. G1 E-6.80000 F1800.00000) command in my print will be active and on top of that retraction, there will be 6.0 mm for all three with the "M207 S6.0 F2400"by 3D-Print - Duet
Does M207 S6.0 F2400 work with firmware newer than Z0.075-rc1-dc4? I installed RepRapFirmware-1.11-dc42.bin and the retraction with all three stepper is not working, only the printing stepper. Do I need to go back a version? Or look somewhere else for this behavior. Thanks!by 3D-Print - Duet
Quotedeckingman Quote3D-Print You are correct..... when I finally sliced the STL in relative, it a works...... It does make sense why all the issues..... The tool change is also is seamless without any issues. Thanks although this was painful to watch, I appreciate all your help and persistence........ learning continues. The over retraction and over feeding of filament doesn't occur!!!!!by 3D-Print - Duet
You are correct..... when I finally sliced the STL in relative, it a works...... It does make sense why all the issues..... The tool change is also is seamless without any issues. Thanks although this was painful to watch, I appreciate all your help and persistence........ learning continues. The over retraction and over feeding of filament doesn't occur!!!!!! Awesome stuff!!! When I doby 3D-Print - Duet
Quotedeckingman Change you slicer setting to use relative E distance or extruder setting, however it is worded. Then slice your object again and look at the resultant gcode. The E numbers should all be small values throughout the file, not just at the beginning. Do not try to print something that was sliced using absolute extruder settings with your printer set to use relative. I think that is wby 3D-Print - Duet
Both Cura and Matter Control slicer does the same thing and the behavior with relative and absolute is the same. Is there something in my config.g?by 3D-Print - Duet
I placed an M82 command at the front of the print g-file. then prior to the M567 command put and M83 like below. it still did the same pause but only for 5 seconds, but the stepper still screamed. My firmware is 1.09z-ch (2016-03-20) Dan ............................... G0 X-0.008 Y19.4 G0 X0 Y19.75 G0 X0 Y19.75 Z0.6 M83 M567 P0 E0.0:1.0:0.0 ;###################### M82 ; LAYER:2 M106 S15by 3D-Print - Duet
Thank you! I have the M207 S5.0 F2400 in my config.g file. As well added the G10 since as you mentioned..... it makes since for all extruders to retract and minimize stringing. When I use M83 I have high extrusion rate that strip the filament. I have calibrated my extruders and my steps for my extruder which is a Nema 17 (5.18:1 geared) is 461.35 steps/mm. I will try a different slicer?by 3D-Print - Duet
I did chagne it back to relative, but when I started to print it went crazy printing and stripped out the filament. Thus, I forgot I changed it back to absolute. Not sure why with relative it went crazy?by 3D-Print - Duet
I tried it again and it starts printing layer 75, then stops and makes the high pitch sound. The pause last almost exactly 30 seconds later (I have a movie of this) it restarts printing with the new mix ratio. What if I added an M400 code before and after the M567 code?by 3D-Print - Duet
Awesome results today. I was successful in sending the M567 P0 E0.0:1.0:0.0 command during a print from the web interface with seamless change of the mixing ratio from extruder #1 to extruder #2. I also placed this M567 into the print gcode file and was able to change the mixing ratio and color with the command. I set up second change later in the print and changed from M567 P0 E0.0:1.0:0.0by 3D-Print - Duet
Quotedc42 Perhaps you have a Duet 0.8.5 and deckingman has a Duet 0.6? The numbering of the DueX4 drivers and heaters depends on which version of Duet it is paired with. I do indeed have the 0.8.5.by 3D-Print - Duet
Quotedeckingman M563 P0 D0:1:2 H1 ; Define tool 0 with all 3 extruders I was curious how your extruders are pluged into the Duet and Duex4 since you have set up drives 0, 1 and 2. I am set up on 2, 3 and 4 since I could not get the first Duex4 terminal to work. Likely due to my set up. Thanks,by 3D-Print - Duet
Quotedeckingman Quote3D-Print Sending the M567 to change the mixing ratio of a sellected and active tool makes more sense. This I know I can do!!! Awesome. I will try this and see what happens. As I think about it I don't really need to do a retraction and unretract with the diamond head since oozing from another head is not an issue. Simply change the extruders ratios from the command linby 3D-Print - Duet
Quotedc42 What I meant was to send an M567 command to set new mixing ratios for the current tool. I'll look into why sending a Tn command during the print doesn't work. If I also click on the "heater 1" link on the web interface it also locks up the system as described above.by 3D-Print - Duet
Sending the M567 to change the mixing ratio of a sellected and active tool makes more sense. This I know I can do!!! Awesome. I will try this and see what happens. As I think about it I don't really need to do a retraction and unretract with the diamond head since oozing from another head is not an issue. Simply change the extruders ratios from the command line or drop the M567 code into tby 3D-Print - Duet
I am tying to modify my g-code print files to change tools (different extruders). I am using the RoStock V2 delta with the Duet and Duex4 with the Diamond print head. i am able to easily print with any of the three extruders and can change tools (extruders) with the pause and resume command, but have had trouble putting the code into the print file gcode. As noted below I can sent the M567 comby 3D-Print - Experimental
Thank you, the python script function is quite nice. I still not sure from this how to structure the change commands. I left this message as well in the other thread. ..................... Of note: The successes!!!!!! If I pause and then change tools by clicking on the web-interface "heater 1" and then selecting another tool, this now works to change the extruder and color. i think this nowby 3D-Print - Duet
Quotedc42 If you are going to do a manual tool change in the middle of a print, using different extruders on the two tools, then you must use relative extruder coordinates in the gcode file. Thanks. Of note, I did try to upload my print g-code for your review, however, it was too large. I would need to zip it if it was still important to review. To summarize my task list. There are two issuby 3D-Print - Duet
Quotedeckingman I've never tried passing tool commands during a print - mine are always embedded in the gcode file itself. . .. What are the codes that you insert into your print g-code to make a tool change?by 3D-Print - Duet
What are the codes that you insert into your print g-code to make a tool change?by 3D-Print - Duet