Hi Mihai, I´m experimenting with M572 too. Do you enabled coast in Simplify3D as well? What about Wipe? Can you please post your settings in S3d? I know that I can´t copy it to my settings because of different filament, speeds etc. But what is your best experience so far? regards Dirkby critical_limit - Delta Machines
still available 1390,- € incl. shipment in Germany 1410,- € incl. shipment EU countriesby critical_limit - For Sale
Hi David, thanx for your reply. But I´m not talking about ONE IR board on a Delta. On each tower I would use a IR-Board. But I don´t know how to connect to the duet. As far as I know the duet has these pins on endstops: GRD -- +3.3V -- Signal Can I connect your IR-Boards to the endstop pins on the duet and will it work? Hall-O Boards are out there enough. But what I read is that they are nby critical_limit - Controllers
Hi All, anybody knows if it is possible to use the IR-Mini Sensorboard as endstop and how to connect to the duet? Maybe David can answer this question and how to connect or what to do. Found that Davids IR-Board is more accurate than simple mechanical switches and so I want to use it for the endstops. Possible? Or any other simple, most accurate solution to connect to the duet? Thanxby critical_limit - Controllers
The additional homing buttons were not shown. It was after a print when it was finished and I set a new bed temp for the next print. You can see that nozzle temp is still higher than room temperature. Maybe the controler was resetting itself? Hm, don´t know because after finished print I was not at the printer. Will keep it watched and report if it happens again.... thanxby critical_limit - Controllers
Hi David, found this after setting bed temp. There are half icons in the background (see pic). After going to print screen back to control screen all normal again. cheers Dirkby critical_limit - Controllers
Hi Chris, back to my issue with file upload. Checked it now with differnt browsers. All the same. It´s going to 100% complete, but not showing the final window. So it failed. Not every time, not due to filesize. Have it with config.g sometimes too. Maybe it´s because of my network, but all other is working fine. Have a fitzbox running. Had no issues with my smoothieboard, but only the webserveby critical_limit - Controllers
Hi Chris, issue with G28 solved. After probing it is going home now. But look at this: Calibrated 6 factors using 13 points, deviation before 0.813 after 155.657 This was after probing.by critical_limit - Controllers
Have a issue too. I have a G28 command in the end in the bed.g All probing is done but G28 is not performed. And in the console I se strange values. Normally I have 0.02-0.06 after probing. Now the value is 1234.56by critical_limit - Controllers
ok, I will try with another browser. But maybe someone else can confirm that using Safari is causing trouble. I want make a osx-app for your webcontrol. But this requires to be fully Safari compatible. cheers Dirkby critical_limit - Controllers
Hi Chris, nice release! Checked it with your fork and Davids fork. Working without any new problem so far. Here are some things I´m dreaming of for the next releases: 1) configuration file in settings menue is not scrollable. Only complete page is to scroll, but not the configuratiopn file itself. Maybe interesting when larger config file is loaded. 2) is it possible to edit the config file iby critical_limit - Controllers
Today I offer my brandnew ATOM 2.0 Kit. New and untouched. Just opend to have a look. Too bad that I´m short on Money actually. Otherwise I would build it by myself, but need the Money urgently.... 1550,-€ incl. shipment in Germany. 1575,-€ incl shipment EU Countries. If you are interested, please leave a PM. Thanxby critical_limit - For Sale
I agree, thats the best option at the moment. But you know how critical it is to lift, pause and resume during the first layer. Specially when you use Filament which is not sticking like hell to the bed. Changing height during movement without lifting retracting, pausing etc is much safer. Thats why I asked for such a function/command. M114 is only reading. M401 and M402 are not available in reby critical_limit - Controllers
Yes, of course it works. Sorry for my bad english. but you have to know the layerhight and enter the absolute value you want to have. If you print many different parts one after the other you often don´t rememebr the layerhigh or can´t have a look so fast. What I mean was, that it would be nice to have a button or command or something like that which adds oder subs e.g. 0.01mm by one click. Soby critical_limit - Controllers
Thanx David for the quick reply. But moving the Z with one relative command isnt that a problem for the rest of the gcode? Its set in the beginning of the file to absolute values. When you send G92 during printing wouldnt it set to relative then for the rest of the print? So you need always 2 commands, do you? First for moving the head up or down, second to go back to absolute mode? hm, have toby critical_limit - Controllers
Hi all, sometimes it happens that I have to change Z0 during the print because I see that the first lines are either to far away or to close. In the moment I stop the print and change via G31 the Z value, upload the config and start again with calibration. The IR Probe is very accurate within 0.01-0.02mm, but the Endstops are 0.01-0.03mm. So it happend that Z0 is off by 0.05mm. Not a big deal foby critical_limit - Controllers
Quotedc42 Great, but please try the new PanelDue firmware I linked to in my previous post and see if that works with your original macro file. Print finished a few minutes ago. Have checked other files in other directoies. All is working fine. Thanks again for your great work! Maybe another idea: hide the file extensions. Actually the files are shown as: "Blabla.gcode". For better reading itby critical_limit - Controllers
@doug:by critical_limit - Controllers
Hi All, due to I was tired to leave the Livingroom every 10 mins to check the printer working in the workshop, I added a view lines into the original reprap.htm in the www folder on the SDcard. Just open the reprap.htm and search for the "<!-- Print Status -->" section. Just under the div class "panel-heading" insert the link of your cams livestream.Thats it. Would be nice when Christianby critical_limit - Controllers
While you worked on the characters I integrated my webcam stream into Webinterface... ;-)by critical_limit - Controllers
You solved it. Loaded your testfile to the macro folder and now it works. Actually I have a print running, but will do other tests after. But I think you solved it completly. Big Thanx!!by critical_limit - Controllers
David, made a test uploading your file. On Web Interface it´s ok like all other accented characters. On the Panel not. See pics:by critical_limit - Controllers
Quotedc42 Just a thought: what size display are you using? I did my tests using a 4.3 inch display. Same here. 4.3 displayby critical_limit - Controllers
Hi David, thanx for the test you did. I erased the files thousend times. Doesnt matter. Maybe it´s because I use a german Win/OSX? Web Interface is using utf-8 and there it´s working. DuePanel is using iso..blabla. Maybe that´s the reason? It´s not a big deal as long as there is no language support in the PanelDue. But maybe others have same issues when using a OS other than english? I don´t knby critical_limit - Controllers
Quotedc42 Two suggestions: 1. Can you confirm that you are running my fork of RepRapFirmware, preferably version 1.09k? 2. Please attach one of the problem macro or gcode files so that I can try uploading it to my Duet with the same name. hm, I see. Yours displayed correct. Yes I run your latest fork. Have attached a makro test file which I´ve downloaded to the card via Web Interface not shoby critical_limit - Controllers
Quotedc42 Accented characters come out properly in the gcode file list for me. Do they for you? Do macro names work properly in the web interface? I can't think why macro files would be any different from gcode files. However, the files with accented characters on my SD card were uploaded over the web interface. If you write the files to the SD card in a PC, then perhaps the PC was using a diffeby critical_limit - Controllers
Have 1.12 installed yesterday night. On startup after connecting to the duet the bed temeratur is showing "-273" in active °C instead of "0" like the hotend. Once you tap field it´s switching to "0". After leaving the menue its switching back to -273°C And in the Macro menue the "German Umlaute" are not shown correctly. Instead of ü, ä, ö there symbols shown. But all other is working fine. Thby critical_limit - Controllers
Now I installed Beta 3. very nice. Fan is not reacting to the button. Think it is because M106 only and not M106 P0 S or M106 P1 S, right? CR in console is nice!! Maybe letters can be smaller tooby critical_limit - Controllers
@ Olaf: In simplyfy3d this feature is offered and I don´t know if other slicers offer this too @David: Is this not shown because it only listen to M106 S$ ?? Same in Web Control. Never changed to M106 P0 S$ or M106 P1 S$ Maybe there must be 2 Fan buttons now because of the 2 PWM Fan outputs?by critical_limit - Controllers
Also I have a request: Is it possible to insert a "Key" Button? During printing or setup the Panel can be locked so it doesnt do nothing when you hit the panel accidentially.by critical_limit - Controllers