Kenne ich mit Smoothieware auch.by ManuelW - Allgemeines
Hey there, where can i find a changelog for smoothieware firmware?by ManuelW - Smoothie
Ich möchte mich auch nochmal dazu äußern. Habe mein Hotend nun auf Micro Swiss Düse und Heatbreak umgestellt und damit lässt sich das Filament nun auch ganz gut drucken. Trotzdem muss eine für PLA untypisch hohe Temperatur eingestellt werden, nämlich bei mir 235°C für den ersten Layer, sonst hält es gar nicht, und für den Druck 230°C bei 100mm/s. Aber zumindest druckt es damit jetzt problemlos,by ManuelW - Kommerzielle Angebote & Produktvorstellungen
Hallo Roman, erstmal danke für deine ausführliche Antwort und Hinweise. Ich habe natürlich alles bereits geprüft, mein Pancake läuft mit 0,9A und hat nen Lüfter dran, E3D Clone wird vor dem Einbau immer als erstes mit hochwertigem PTFE bestückt, Retract ist bei 0,8mm. Wie gesagt, andere PLA drucke ich ohne Probleme bei 210°C mit 100mm/s. Aber, um auch noch ein mögliches Problem mit der Nozzle aby ManuelW - Kommerzielle Angebote & Produktvorstellungen
Also, nachdem ich nun noch grünes PLA und PETG von Das Filament getestet habe kann ich nur sagen, nie wieder. Das grüne lässt sich besser drucken als das blaue, anfangs sogar perfekt bei 80mm/s aber etwas weiter auf der Rolle begannen dann auch die Förderprobleme. Also über 60mm/s scheint das Filament undruckbar. Beim PETG hatte ich ähnliche Probleme. Das Filament fängt im Druck an zu krisselnby ManuelW - Kommerzielle Angebote & Produktvorstellungen
Hallo zusammen, möchte nochmal nachfragen, mit was für Einstellungen ihr aktuelle dieses Filament druckt. Ich habe gerade meine erste Rolle von Das Filament drauf, PLA - Königsblau. Ich kann das nur relativ langsam drucken, komme über 60mm/s nicht hinweg und bin da bei 240°C. bei über 60mm/s bekomme ich immer wieder extrusion Probleme, war mit der Temp auch schon bis auf 250°C hochgegangen. Abby ManuelW - Kommerzielle Angebote & Produktvorstellungen
My Problem isn't that i can't flash the board. Flashing works fine and if i flash the old firmware 1.1.6-bugfix it works also. The Problem is, that the new 1.1.7 firmware only boot 1 time. If i make the printer powerless and power them on again, 1.1.7 won't boot.by ManuelW - Firmware - Marlin
Hey there, i have a strange behavior with Marlin 1.1.7. I flashed 1.1.7 to my printer, Marlin starts and everything is fine. But if i shutdown the printer an restart, then the display is empty and nothing happens. I try'd with recompiling and flashing again, but its always the same. I flashed back to 1.1.6-bugfix (latest) it works fine. I don't know whats wrong. Checked everything in the confby ManuelW - Firmware - Marlin
Found the problem. I did a G28 after G29, that deletes the measured values. No i go with G1 X0 Y0 back to home position and leveling works.by ManuelW - Firmware - Marlin
Hey there, i enabled bilinear ABL on my Marlin 1.1.6 bugfix (downloaded today). It does the M29 well and gives me the measured values on the end. But if i start a print, the values don't used, the bed wont go up/down as needed. I attached my configs and my start script. Maybe someone can help me with this problem. Regards Manuelby ManuelW - Firmware - Marlin