Quotedc42 You will get layer shifts if you use stealthChop mode at high speeds. That's why these chips have an option to switch automatically to spreadCycle mode above a certain speed. I print 60mm/s also same travel speed. QuoteDust your only options are to Increase your current or lower your speed. X and Y have 800mA as before but i will try increase current. Thanks for adviceby keremdikmen - Controllers
Thanks for advice. Now interpolate false and all drivers 256 microsteps. Motors seems like warm as before. Now same printing speed and it has layer shifting unfortunatelly. X and Y drivers has 800mA current as before. Only shifting stops when i lower speed around %50-60 percent. what is the cause shifting? Thank you very muchby keremdikmen - Controllers
Thanks for reply. If i set 256 micro stepping, motors gonna be very loud (Like video on my previous post) Doesn't matter interpolation on or off. What cause of this sound? (Even Stealthchop ON, it gives weird sound like frequence ) Now i'm using 16microsteps all driver. It's working stealthchop mode and noise same as before (no uart soldered pin). (But if i close stealthchop mode its gives noby keremdikmen - Controllers
Thank you very much QuoteDust I see from a earlier post you have SKR 1.3 for UART mode you need to remove all jumpers under the stepper driver modules, and connect up the UART pins as indicated I thought if i do only this and it must work but also i must soldered 2 jumpers each driver. Now its can be communicating. But now there is interestin problem showed up. Interpolation is enabled and miby keremdikmen - Controllers
Hi, i configured driver to 256 microsteps. And i don't know exactly but must be at least 16 steps. I try to calculate steps/mm on reprap prusa calculator. If i chose 1/16 microSteps and 2mm pitch my steps settings should be 1600. But now i using only 200steps/mm. So i using 1/2 microSteps? Also my xy configiration is 40Steps/mm. But 2mm belt pitch and 20teeth pulley it has 1/8 Microsteps? So whby keremdikmen - Controllers
Quoteinvernomuto Where do you buy replacement for C15 and R17? I am in on the same boat... Thanks!! I didn't buy, I removed them from old parts(motherboard etc.). But you can find this way. Also If you have you can buy from local electronic shop or internet. For SKR 1.3 R17=4.7k and C15=10ufby keremdikmen - Smoothie
But is there any way to do pid tuning for heated bed because my heated bed gives me thermal runaway error constantly. Maybe if i can do pid settings its can be work right or is there any different settings for it. And my problem is: i set up 100 degrees and it can be reach any problem. But after reach its goes down 95 - 94 degrees and printer is displayed printer halted error. Probably code saysby keremdikmen - Controllers
QuoteOhmarinus Can it be the jumper pin isn't installed on 'int' power setting? It's in the middle of the board where you can choose to either power it through USB or INTernal 12v? I'm not sure what else could be the problem, this is where I would look first. Thanks for your inqury. But i know jumpers purpose. Normally it works with usb and int pin (only usb cable connected pc) also it can be cby keremdikmen - Controllers
Thank you for reply. Firsly i didn't receive any sd card and i use different sd card. My friend and me bought same board. I can use pronterface or other programs with his board. Also i can connect my board previously. Now i don't know whats happened. I need PID settigs for my heated bed but its hard to make without pc connection. Note: You can see. it can be connected and controlled on pcby keremdikmen - Controllers
Hi, unfortunately i have connection issue recently. Before i can connect board any problems. I don't know why but now i try two computers and I saw just Unknown Device in device menager. I use win10 both computer and as far as i know no need driver for win10. Also i find "smoothieware-usb-driver-v1.1" on the internet. But it doesn't help. Any help would be very good. Thanks.by keremdikmen - Controllers
Finally i solve this. Firstly thermistor's capacitor is failure and because of i see wrong value on screen. After then i replaced it but i can't properly solder resistor so its give wrong value again. Now both are okey and i see true value. Thanks for helpby keremdikmen - Smoothie
I checked c15 capacitor, it failured and i change it but unfortunately same as before. Can i fix that or use other thermistor connector?by keremdikmen - Smoothie
Hi, i have skr 1.3. I decided make a heated bed my printer. Everything is done but something wrong my board. Firstly doesn’t have heated bed settings on my LCD then i change bed termistor code 0 to 1 in configiration.h. I read 120degrees without NTC and if i plug it it change little bit. I measured thermistor connector on board. It has 3 thermistor connector and two of them has 3.3v and my failedby keremdikmen - Smoothie
Sorry for late reply. Thank you for your comment. I have tried your said before create this topic. I edited platformio.ino, Configuration.h and Configuration_adv.h at the same time and it gave continously LPC1768 error after build some reason. After then i started over and this time i goes step by step and build them. Thereafter it's successfully build and upload. So, that's how i did. Maybe helby keremdikmen - Firmware - Marlin
Hi, i recently received SKR 1.3 board. I tried upload latest marlin version. When i try upload arduino always times out. Here it is error code: avrdude: stk500v2_ReceiveMessage(): timeout avrdude: stk500v2_ReceiveMessage(): timeout avrdude: stk500v2_ReceiveMessage(): timeout avrdude: stk500v2_ReceiveMessage(): timeout avrdude: stk500v2_ReceiveMessage(): timeout avrdude: stk500v2_ReceiveMessage():by keremdikmen - Firmware - Marlin