@Hallo Helmut Wähle mal das Board aus dann sollte es funktionieren MFG Stefanby Micro3D - FAQ - Bei Problemen und allgemeinen Fragen ...
@Hallo Er hat nacht der Anleitung Gebaut wenn ich das richtig mitbekommen habe MFG Stefanby Micro3D - Allgemeines
@Hallo Test es mal so Only thing you need to do is: #define SERIAL_PORT -1 // is the USB port #define SERIAL_PORT_2 0 // is the serialport for the TFT #define BAUDRATE 115200 // for the serialport and make sure that the firmware on you TFT 3.2 is sett to 115200 and Marlin.. MFG Stefanby Micro3D - Software
Ich schau mir das Morgen mal anby Micro3D - Allgemeines
@Hallo Ich tippe mal auf Cura Settings, was für eine Linienbreite hast du eingestellt am besten auf 0.4mm Düsen Durchmesser einstellen. MFG Stefanby Micro3D - Allgemeines
Hallo Wenn das zweite Bild ( image1.jpeg ) dein Drucker von zeigt dann ist der Y_Endstop falsch konfiguriert und elektrisch falsch gesteckt , du musst in als MIN_Endstop Einstellen und stecken . MFG Stefanby Micro3D - Software
@phyber Verstehe ich das richtig , dein X_Endstop Rechts und dein Y_Endstop ist Vorne. Sollte es so sein dann musst du das so einstellen. // @section homing // Specify here all the endstop connectors that are connected to any endstop or probe. // Almost all printers will be using one per axis. Probes will use one or more of the // extra connectors. Leave undefined any used for non-endstop anby Micro3D - Software
@Hallo Nimra Ich hab mir mal deine Config.h angesehen Ich glaube du hast dieses Board // The following define selects which electronics board you have. // Please choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_14_EFB #endif // @section homing // Specify here all the endstop connectors that are connected to any endstop or probe. //by Micro3D - Software
@Hallo Stephan So musst du das beim Ramps einstellen. // Enable pullup for all endstops to prevent a floating state #define ENDSTOPPULLUPS #if DISABLED(ENDSTOPPULLUPS) // Disable ENDSTOPPULLUPS to set pullups individually //#define ENDSTOPPULLUP_XMAX //#define ENDSTOPPULLUP_YMAX //#define ENDSTOPPULLUP_ZMAX #define ENDSTOPPULLUP_XMIN #define ENDSTOPPULLUP_YMIN #define ENDSTOPPULLUby Micro3D - Software
@Hallo phyber darf ich fragen was für ein Board du verbaut hast, davon hängen auch die Endstops Settings ab. //=========================================================================== //============================== Endstop Settings =========================== //=========================================================================== // @section homing // Specify here all the endstopby Micro3D - Software
@Helmut Deine Z-Steps passen nicht /** * Default Axis Steps Per Unit (steps/mm) * Override with M92 * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] */ #define DEFAULT_AXIS_STEPS_PER_UNIT { 100, 100, 4000, 105 } Im Video hat man das gesehen das die Düse auf 0.3mm fahren wollte ist aber auf 3.0mm gefahren. Weil wir alle Daten kennen können wir die neuen Z-by Micro3D - FAQ - Bei Problemen und allgemeinen Fragen ...
@luclass was meinst du wie schnell kann man da mit Drucken /** * Default Max Feed Rate (mm/s) * Override with M203 * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] */ #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } /** * Default Max Acceleration (change/s) change = mm/s * (Maximum start speed for accelerated moves) * Override with M201 *by Micro3D - Allgemeines
@Hallo Quote Es muss doch moeglich sein, dass ueber den Abstand von Sensor zu Nozzles dann die jeweilige Position ueber dem Bett berechnet wird. Oder sehe ich da etwas falsch? Das mach Marlin ja , ich sehe da nur ein Problem wenn der Sensor auf denn 0 Punkt steht denn ist die Düse in Negativen Bereich die frage ist würde das richtig ausgeglichen werden ? Ich bin der Meinug werendes des levelingby Micro3D - Allgemeines
@Robin Du brauchst nicht zu testen mir ist da wohl ein Fehler unterlaufen , du wirst wohl Druck Volumen verlieren das steht fest . Jetzt müssen wir ein vorgehen überlegen um das beste b.z.w. mögliche größte Druck Volumen heraus zu holen . MFG Stefanby Micro3D - Allgemeines
@Hallo Das habe ich geändert , kannst ja mal testen // The size of the print bed #define X_BED_SIZE 300 #define Y_BED_SIZE 400 // Travel limits (mm) after homing, corresponding to endstop positions. #define X_MIN_POS -50 #define Y_MIN_POS -40 #define Z_MIN_POS 0 #define X_MAX_POS X_BED_SIZE #define Y_MAX_POS Y_BED_SIZE #define Z_MAX_POS 268 #if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(by Micro3D - Allgemeines
@Hallo Poste mal Bitte deine Config.hby Micro3D - Allgemeines
@Hallo Wintex Bantha Hardwarekiller Hier steht das auf Schwartz und Weiß ( auch wenn man nicht Englisch kann sollte man das verstehen )by Micro3D - Elektrik & Elektronik
@Hallo CKCMorgoth Marlin 2.0 läuft auf die Stock Board. Quote ......oder ein anständiges Tutorial wie ich die Backlash Calibration in 1.1.9 einbinde........ Zeig mal ein paar Bilder von die Druck Ergebnisse . Stell mal die Config.h zur verfügung .by Micro3D - Elektrik & Elektronik
Schau dir auch noch das Video an Dann versteht man das auch. Edit: Probier das mal aus, ich weiß ja nicht was für Endstop du benutzt und so die sitzen. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). #define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. #define Y_MIN_ENDSTOP_INVERTING true // Set to true toby Micro3D - Software
@Hallo Micha1911 /** * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT -1 Stell mal Bitte noch ein Paar Bilder hier rein. Uby Micro3D - Software
@Hallo Chris1994 und Willkommen Wenn der X_Endstop sich auf der linke Seite befindet dann ist es X_HOME_DIR -1 ( Dieser wert wird dann nicht mehr verändert ) INVERT_X_DIR false oder true anpassen , sollte sich das Homig verhalten sich nicht verändern dann stimmt was mit dem Endstop Setting.nicht. MFG Stefanby Micro3D - Software
@Hallo Srek kannst du von dein DuoCube ein Foto machen wo der Z-Endstop sitzt ich kann mir grade darunter nichts vorstellen und am besten deine Config.h zur verfügung stellen. Für mich klingt das so das mit dem Endstops Settings noch nichts stimmt. Hast du zur erst X & Y Gehomt und dann Z ? Edit: Eine Idee hatte ich noch ( ich weiss nicht was für ein Z-Endstop du hast ) wen du z.B. einenby Micro3D - Allgemeines
@Hallo Freki_0815 Hast du diese Marlin 2.0 geladen , die version brauchst du für dein Board MFG Stefanby Micro3D - Software
@Hallo cheffeundwackl Versuch mal das , wenn dein Temp zum Beispiel unter 50°C geht dann geht die Pumpe aus // @section extruder /** * Extruder cooling fans * * Extruder auto fans automatically turn on when their extruders' * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. * * Your board's pins file specifies the recommended pins. Override those here * or set to -1 to disable coby Micro3D - Software
@Hallo Andre Ich habe grob in Marlin 2.0 nach gestellt , das board wird auf jeden fall unterstüzt #define MOTHERBOARD BOARD_GT2560_V3. Grob mit disen werten /** * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN * * Enable this option for a probe connected to the Z Min endstop pin. */ #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN /** * Z Servo Probe, such as an endstop switch on a rotating arm. */ #defiby Micro3D - Software
@Hallo /** Number of servos For some servo-related options NUM_SERVOS will be set automatically. Set this manually if there are extra servos needing manual control. Leave undefined or set to 0 to entirely disable the servo subsystem. */ #define NUM_SERVOS 2 // Servo index starts with 0 for M280 command Gib mal eins an . MFG Stefanby Micro3D - Software
@Hallo botchjob-rbt was für beschleunigungswerten hast in der FW eingestellt. Mach mal Test weise diese werte. MAX_TRAVEL_ACCELERATION_UNITS_PER_SQ_SECOND_X 2400 MAX_ACCELERATION_UNITS_PER_SQ_SECOND_X 2400 Und nicht vergessen bei Aktivierten EEPROM wieder auf Werkseinstellung zu setzen. MFG Stefanby Micro3D - Projekte
@Hallo Rene Kannst du mal von dein MELZI Board ein Foto machen das interessiert mich mal . Quote .....dass er dort anfängt zu drucken, wo er vorher nach dem homing hingefahren ist.... Das sollte das Problem Lösen Lösch mal bitte das + TRONXY_X_BED_OFFSET & das + TRONXY_Y_BED_OFFSET raus. // Travel limits (mm) after homing, corresponding to endstop positions. #define X_MIN_POS TRONXY_X_Bby Micro3D - Software
@Hallo rawyal kannst du mal Bitte die Configuration.h zur verfügung stellen Danke. Ist noch diese Bed größe eingetragen ? // The size of the print bed #define X_BED_SIZE 340 #define Y_BED_SIZE 315 Ist das deine Bed göße (noch mal nach messen) // The size of the print bed #define X_BED_SIZE 225 #define Y_BED_SIZE 230 Wenn das bei dir Aktiviert ist sollte er nach XY Homing das Z in die Mitteby Micro3D - Software
@Hallo Conrad die Z_CLEARANCE_DEPLOY_PROBE , Z_CLEARANCE_BETWEEN_PROBES & Z_CLEARANCE_MULTI_PROBE die würde ich auf 5 lassen. Z_AFTER_PROBING sorgt da für das nach dem Z-Homing auf 0 fährt , und das Z_PROBE_LOW_POINT -2 muss so bleiben ( sonst "Probing gescheitert" ). /** * Z probes require clearance when deploying, stowing, and moving between * probe points to avoid hitting the bed andby Micro3D - Software