Dust > Thank You I was given some code below and appears to require all lines enabled to function correctly. // Path:Marlin\Configuration_adv.h #define PROBE_OFFSET_WIZARD #define PROBE_OFFSET_WIZARD_START_Z -4.0 #define BABYSTEPPING #define BABYSTEP_DISPLAY_TOTAL #define BABYSTEP_ZPROBE_OFFSETby Roberts_Clif - Firmware - Marlin
You could be correct. I found the BABYSTEP_ZPROBE_OFFSET after I posted though, it is in a different LCD menu tree, still confusing me. Did some preliminary tests it kind of does what I wanted to do. will have to do full testing to be sure.by Roberts_Clif - Firmware - Marlin
I was watching a Youtube video showing CR Touch installation. In the video it shows I could adjust the Z-Offset live and save the offset image below simple set Offset click and nozzle moves to height. I do not know how to enable this menu help me. Complete video Here this is in Z-Offset section 5 at 21:30 Thank you in advance for your help. I should note that I have a 2004LCD an not the LCDby Roberts_Clif - Firmware - Marlin
Have you tried to invert the Stepper direction here #define INVERT_X_DIR true #define INVERT_Y_DIR true #define INVERT_Z_DIR trueby Roberts_Clif - Prusa i3 and variants
I use a simple G-Code in start/end G-Codes to start my fans M106 P0 S128 ; P0 = 1st Fan M106 P1 S128 ; P1 = 2nd Fanby Roberts_Clif - Firmware - Marlin
I have noted after I have flash the Marlin 2.0.9.3 firmware if you do not initialize EEProm some functions do not work correctly. Click Select Configuration Click Select Advanced Settings Click Initialize EEProm Click When I install Marlin 2.0.9.3 on my controller none of the steppers motors worked an various other problems. After completing above procedure all work as intended.by Roberts_Clif - Firmware - Marlin
I am using Dual X and Dual Y steppers code below. This configuration is working on a MPCNC. #define USE_XMIN_PLUG #define USE_YMIN_PLUG #define USE_ZMIN_PLUG #define USE_XMAX_PLUG #define USE_YMAX_PLUG Configuration_adv.h #define Y_DUAL_STEPPER_DRIVERS #if ENABLED(Y_DUAL_STEPPER_DRIVERS) #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions #defby Roberts_Clif - Firmware - Marlin
Well hello Guess What!!! I have a 3D Touch working on my newest 3D Printer. Have not yet designed a modified mount the my Slide adjustable thumb screw Mount work. I Need to acquire some extension wires as my 3D Touch only has about 6 inches of wire. New if I put my mind to it would find the solution.by Roberts_Clif - Firmware - Marlin
I configured Marlin 1.1.9BF several time today for Bl-Touch with no success. Could not get the 3D-Touch to connect with D11 Pins so I pulled off the white connector plastic cap. This exposed all 12 pin headers however 3 pins were cut short seen in image below. This could also explain why I could never get it to work before, the pins were not long enough. My 3DTouch has a different wiring neediby Roberts_Clif - Firmware - Marlin
Direct from the configuration.h file of Marlin Firmware 2.0.9.3 /** * Stepper Drivers * * These settings allow Marlin to tune stepper driver timing and enable advanced options for * stepper drivers that support them. You may also override timing options in Configuration_adv.h. * * A4988 is assumed for unspecified drivers. * * Use TMC2208/TMC2208_STANDALONE for TMC2225 drivers and TMC22by Roberts_Clif - Firmware - Marlin
I believe you need to enable these before the fans can function correctly. //#define E1_DRIVER_TYPE A4988 //#define E2_DRIVER_TYPE A4988 If you are using a single extruder in pins_TRIGORILLA_14 and connect fan2 to pin 44 should enable this to allow "Has_Multi_Hotend" for pins_TRIGORILLA_14 // For Cyclops or any "multi-extruder" that shares a single nozzle. //#define SINGLENOZZLE should enabby Roberts_Clif - Firmware - mainstream and related support
Well I would really like to have step/direction/enable pins. Though this controller does not have any pins that control the step/direction/enable. I only created this pin mapping because Hictop Users have asked many times for a Pin diagram, include myself. Have been trying to configure the BL-Touch for use with my Hictop 3D Printer, an without knowing the pin layout it makes any firmware chanby Roberts_Clif - Prusa i3 and variants
Then I am finished with the Hictop controller Pin-out Mapping. The pin-out mapping is very similar to the Base v1.3 an MPX.3 they do not have a H6 connector You may note : two ICSP ports on controller. H6 is a standard ICSP header, but for programming the ATmega 16U2 This will give the Hictop users a more detailed look at our controllers pin-out. Older Hictop controllers have basically the sby Roberts_Clif - Prusa i3 and variants
Oh!!! Of course forgot that the ATmega 16U2 can be programmed. Thank youby Roberts_Clif - Prusa i3 and variants
I have a controller from Hictop MPK V1. I do not have a complete board Connector Pin-out. Please supply me any information you may have regarding connector labeled with an " H6 ". More information they replaced the FT232RL - FTDI with an ATmega 16U2 High Speed USB controller this is where H6 connects. Thank Youby Roberts_Clif - Prusa i3 and variants
I had this problem for a while on My Hictop 3D Printer. I decided to get a different Proximity sensor from the original shown below So I purchased a Omron TL-W3MC2 this is a flat sensor, I re-designed the Mount above shown below. I went from 65 mm behind the nozzle to 20mm behind the nozzle.by Roberts_Clif - Prusa i3 and variants
I have setup my ramps.this works the Cable is Black, Green, Red and Blue. Check your wiring.by Roberts_Clif - RAMPS Electronics
Had problems with this found that I could use #define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow I use for stow with an Adjustable thumb screw for fine tuningby Roberts_Clif - Firmware - Marlin
Honestly! Politicians Promises last longer than New Years Resolutions. Anyway . Here goes !!! I have became a lounge lizard during the Covid and have slowed down considerable doing most of my hobbies. This is for sure what we did yesterday will cost of more in the future. Hope everyone can still afford this Hobby. I Plan to upgrade one of my single color printer to a Tri-Color 3D Printer. Wouby Roberts_Clif - General
I too killed the regulators. There is many post as to how to replace the AMS1117-5.0 I however replaced with a higher current Buck Converter. And more here I previously had replaced the AMS1117-5.0 regulator it was not too long before it fried again, my solution was to increase the regulator current to 3 amps I choose this buck converter because of 3amp current, preset voltage levels / variaby Roberts_Clif - RAMPS Electronics
Depending on your level of programming skills you could use it in virtually a million projects. From a simply Z80 machine emulator to a Wristwatch. For more questions search the web all projects and learning tutorials are located in the millions of online tutorials.by Roberts_Clif - General Mendel Topics
You are most welcome . . .by Roberts_Clif - Firmware - Marlin
Your Marlin appears correct though my code has an additional line. // ************************************************************************************************************************ // The RepRapDiscount Smart Controller (Red PC // #define REPRAP_DISCOUNT_SMART_CONTROLLER // CL: Stock HICi3 20x4 LCD controller #define NEWPANEL // enable this if you have aby Roberts_Clif - Firmware - Marlin
I cannot retrieve Marlin from anything you have posted???by Roberts_Clif - Firmware - Marlin
Then if you post your Marlin configuration file to a share like google drive and post a link. I would take a look at your configuration, an may spot a configuration error...by Roberts_Clif - Firmware - Marlin
I found that if you want to get the best out of Octoprint then you should not use the minimum components. Note Right Model below vs the Left Model I was using Raspberry Pi 2 this Pi does not have the power required to 3D Print while using Octolapse add-on feature in Octoprint. Using a faster Raspberry pi with Octoprint will eliminate the fuzzy exterior texture.by Roberts_Clif - Firmware - Marlin
On the back of your LCD there is a contrast control potentiometer turning it will adjust the LCD contrast.by Roberts_Clif - Firmware - Marlin
On the back of the LCD controller there is a contrast control Have you tried to adjust it. if not then Post your Marlin Config will have a look.by Roberts_Clif - Firmware - Marlin
Both the connectors in top most photo this is the new LCD from BIgTree the Next photo down is my original controller from Hictop a 2004 LCD, I think hictop 2004 LCD is a clone of the RepRap Smart controller. THe hictop 2004 LCD also has right angle Connectors. Look at the Red Cable wire and note which side it is on. You will also note the both connectors on the big tree controller are the opposby Roberts_Clif - Firmware - Marlin