Hi, I had this problem also ones , but this was because skip stepping and endstop problem .by garaguido - Firmware - Marlin
I used the latest Marlin 2.0.7.2 bugfix from 18 feb 2021 and can not run my endscript any more.I think there is a define mode M84 in the software that I must undefine. M84 is now incorporated in the software , when I compiled the software and run it the software is stopping al motors when print is done and not running my endscript where I controlled the M84 myself . This problem was not in Marliby garaguido - Firmware - Marlin
My setting Z_AFTER_PROBING 5 is enabled , but no succes The problem is not by probing , but by HOME or G28 command , the head stays on pos 0,0 I want it 5mm from the bed .by garaguido - Firmware - Marlin
Hi For you is this a verry good solution , I see. I have no trouble with the first layer on my bed , I use Mesh leveling ( 9 points) and is always , after a fiew testprints OK. My problem is the distance from the bed when the printhead is at Home position X=0 Y=0 (rest position afther home command) , I wand this Z at least 5mm high.by garaguido - Firmware - Marlin
Hi My settings are the same "#define Z_CLEARANCE_DEPLOY_PROBE 10" and "#define Z_CLEARANCE_BETWEEN_PROBES 5" But by Auto homing , my Z hight is at min. 0.1 mm and still to close to the bed , my magnetique flex printbed temp. will stand for max. 150 degrees C , but the extruder go's 215 degrees C. Therefore I will the head at min. 5mm from the bed when Auto homing or homing with G28 . I haveby garaguido - Firmware - Marlin
How to set , in Marlin, X=0 Y=0 and Z=5mm after G28 homing? The raison is :to protecting my flex magnetique printbed by warming up , preventing the nozzle touching or to close the bed .by garaguido - Firmware - Marlin
I have tryed using RCfixbugs branch , but no succes . The changing , i discover on the display menu was a extra sub layer , concerning bed leveling command . But still , my bed leveling dos not work via the LCD. By compiling it , i had several warnings from Arduino IDE about the Dutch language file (language_nl) , uploading to MP was no problem .by garaguido - Firmware - Marlin
I have up-loaded the newest Marlin 1.1.0 RC5 software with activated the "Mesh_bed_leveling " and "Man_bed_leveling " in the configuration.h file. When i uploaded it with Arduino IDE_nightly (= 1.6.8 with bugs solved , there is a communication problem within 1.6.8 ) , i can give a command G29 S1 ( = mesh bed leveling ) from Repetier Host and it is working after i give a M420 S1 ( = bed level aby garaguido - Firmware - Marlin
The Marlin RC5 was a clean-up (text and code) from RC4 and great improvemend , RC4 was not working for me ,when i make a print direct from the LCD SD card . When i compiled and uploaded it there was for me no difference in working except on the LCD this was great improvemend . For the evaluation and settings between two files , i use Winmerge (free software), verry usefull and verry fast for cby garaguido - Firmware - Marlin
I use a MKS_BASE compatible board , on my Prusa i3 printer. It is the Xinray Melzi board and is compatible in Marlin 1.1.0 RC5 with " Ramps 1.4 EFB " or with "MKS_BASE " Have you tried these configurations ?by garaguido - Firmware - Marlin
Voor diegene die het nog niet moesten weten .....? Vandaag is de Marlin 1.1.0 RC4 te verkrijgen op de website van Github , er zijn verschillende verbeteringen en bugs in de software aangepast.by garaguido - Software
Het rare is dat er een Z hoogte verschil ontstaat , van ongeveer + 0,3mm , na de eerste print . Ik gebruik inderdaad een - Z offset in Marlin en die is steeds perfect bij mijn eerste print , indien de printer een tijd heeft uit gestaan bv:printen de volgende dag , en nee er is niets dat te warm wordt ivm uitzetting van materialen , dan moest ik dit vroeger reeds hebben gehad zonder bed level sby garaguido - Electronica
Heb nog wat aan het testen geweest ,resultaat was dat als ik via het LCD display een "Auto home " zend voor een autobed level commando dit probleem , nml .Z hoogte verschil niet heb . Op het LCD display wordt dan ook de Z hoogte aangeduid . Wanneer ik een autobed level commando (G29) laat uitvoeren , via de begin Gcode in Slic3r ,er bij de 2e print een hoogte verschil ontstaat en er ook geenby garaguido - Electronica
Ondertussen zijn alle kinderziekten van dit bord ook werkend met een nieuw aangekocht full-grafics LCD opgelost. De autobed leveling werkt ook , maar nu is er toch een raar fenomeen , ik weet niet of de nieuwste Marlin RC3 software is . Repetier is het zeker niet en ook de Slic3r niet heb dit met oudere stabiele versies getest en zelfde resultaat nml 1e print eerste layer perfect op bed , 2e nby garaguido - Electronica
Opgelost , het vermogen van de spanning stabilisator is max 500mA , met de Melzi 2.0 en de LCD is dit op het randje van het vermogen daarom flikkert hij.by garaguido - Electronica
Opgelost , in de instelling van Marlin stond de CRC check van de SD card aan .by garaguido - Electronica
Wanneer ik een eerste printlaag print , met mijn autobedlevel (G29) en ingesteld met Marlin 1.1.0 RC3 , is dit een perfecte 1ste laag met goede hechting . Maar wanneer ik daarna , op dezelde dag nog een tweede en zelfde stuk print , zonder wijziging van instellingen in Slic3r , is er na een autobedlevel (G29) een verschil in hoogte van 0.35mm ivm de eerste printlaag. Om dit te corrigeren moetby garaguido - Software
In Ikea Belgie vind je er nog denk ik .by garaguido - Warmtebed en Printbed
Ik heb folie gebruikt die achter radiatoren wordt gebruikt 2lagen de bovenste laag extra met kapton tape voor tempby garaguido - Warmtebed en Printbed
Ik gebruik al meer dan een jaar spiegelglas 200x200 van IKEA , ook op 100gr bed temp en nog nooit een probleem gehad . Heeft nog een voordeel nml de warmte wordt goed verdeeld via de kwiklaag van de spiegel . Er zijn 4 spiegels in een pak , je kan gemakkelijk ook van glas wisselen ivm afkoelen van je print .by garaguido - Warmtebed en Printbed
Here are two supliers from Belgium. Velleman from Oudenaarde see at 〈=nl&id=418896 Charlies 3D store see atby garaguido - Extruder, Hotend en Filament
Have anybody also the same problem as me ? Reading from the SD card (Gcode ) on the LCD is very slow , I use the newest Marlin software Marlin 1.1.0 RC3 Anybode a solution for it ?by garaguido - Firmware - Marlin
Heeft er iemand ook opgemerkt dat , het lezen van de geheugenkaart , in dit LCD display , ook zo traag verloopt ? Iemand een oplossing ? Of is het een Marlin probleem , ik werk nu met Marlin RC3 van 1-12-15 ?by garaguido - Electronica
Melzi 2.0 stepperdriver bord voor 3D printer , voorzien A4982 stepperdrivers Melzi 2.0 ATMEGA1284P . Bijbehorend een Reprap Full graffics LCD display 12864 1 jaar oud en weinig gebruikt Prijs op aanvraag .by garaguido - Marktplaats
Yes , I try it to find out , with jumper settings , but still no succes , i must buy a compatible one I supose . Thanks for your responseby garaguido - Prusa i3 and variants
I used my LCD12864 Full Grafics on my Melzi 2.0 ( Arduino 1280) and was working always fine for a year now . Now I upgraded my motherboard to a Xinray board ( Melzi update board ). I neaded this for more memory on the Arduino 2560 ( compatible with Ramp 1.4 or MKS BASE) and the LCD12864 is not working anymore . The settings are correct in Marlin 1.6.0 with the newest 8glib software inclosedby garaguido - Prusa i3 and variants
Is there a Prusa i3 user , that has used and instaled such a motherboard ? My question is , how the config file is set and the sketch setting in Arduino for uploading to the board ?by garaguido - Prusa i3 and variants
Dit probleem is nu opgelost Het heeft te maken met de 5V stabilisatie van de chip , kan maar 500mA leveren en met de LCD er bij is dit juist iets te veel . Een mogelijke oplossing is , via een apparte gevoede USB hub , de processor alleen te voeden na het instellen van de jumper op het bord.by garaguido - Electronica
Is er iemand die reeds zo een upgrade bord , ATMEGA 2560 van Xinray, heeft gebruikt ? Wat is de configuratie.h file ervan , zoals type bord , baudrate , welk Arduino bord type bij upload van sketch enz....? Graag enige hulp daarover , ik gebruik nu een Melzi 2.0 met LCD display , voor Prusa i3 aangepast naar bowden extruder.by garaguido - Electronica
Ik heb ook mijn , Heacent Prusa i3 , geupgraded met een bowden extruder en automatische bedleveling of trimming . Dit is vrij aardig gelukt en de printjes zijn redelijk goed , alleen is er een probleem van retracting , dit heeft met het bowden princiepe te maken . Na aanpassing van de rectract lengte en snelheid , in Slic3r , was het wel beter, moet volgens mij ingesteld worden als multimaker priby garaguido - Projecten