Show all posts by user
Page 1 of 2
Pages: 12
Results 1 — 30 of 51
Ok I have an Easythreed X1
I am trying to connect the Bed to the Board and having no luck making it hit 60C best I have got so far is 58C and that was P900 I200 D1000 It's so cold it times out before the PID AutoTune can start, and I am pumping in 13VDC from a 25Amp supply the Board and Heat bed are Rated for 12 to 24VDC the Original would ache ave 61C with a 12VDC 2.5Amp Brick people suggested
by
Justinjjhcs1
-
Calgary
well If you buy a china Product, the Data sheet is in Mandarin or Non existent mine was a Kit with 4 Pads it did say 12/24VDC, but they had it hooked Directly to..
by
Justinjjhcs1
-
Reprappers
thanks Ill try this on my Rep Rap Wallace there is a possibility that I forgot to do something I have done before... Ill check the Codes and change what is Different the Default for all printers now is Front, left for home... If this dose not work Ill try switching motors right for left and left for right...
by
Justinjjhcs1
-
General Mendel Topics
same and no and nope... this only occurs when I home the Z axis not X or Y I have this issue with my pruas Mendel II3 but it will still home and Print so I am thinking bad Wire or Motor or stepper driver?? but if that were the issue it would not even move. I am getting this on my Rep-rap Wallace now but there is no cause... I have done a Cube simulated print the printer goes through its Gcode pro
by
Justinjjhcs1
-
General Mendel Topics
I have this same problem the only way I ave solved it in the passed was downloading a Fresh copy of Marlin and then only changing precisely what I needed so try a Default copy and see it it occurs...
by
Justinjjhcs1
-
General Mendel Topics
Ok I am no stranger to Marlin and how it works.... there is no lines for fixing this Issue 2 things the Z tends to Jam and it will only go Down... Early versions of Marlin had a way to correct this issue but I cant find it in Marlin 1.1.9...and it cant be that hardware I had it running on my Hypercube some weeks back think its the same issue as always 2 motors one Driver.. getting half of everyth
by
Justinjjhcs1
-
Firmware - Marlin
I have the exact same problem...
I think this is a Marlin Bug....
It dose not allow your to set Mixing extruder and Cyclops extruder functions, Marlin is not Intuitive like you think.
If you Set it up in the Obvous way just looking at the Code it will not allow the C++ compiler to verify? Even if you look.
I think there is a basic command missing like #define EXTRUDERS 2 or that string le
by
Justinjjhcs1
-
Printing
I have since fixed this issue by using older Marlin Firmware and installing the proper pin library for the Display... all problems seem to disappear when I installed a Version of sprinter that had support from my display...
by
Justinjjhcs1
-
Controllers
trying to get this vertion of Marlin to work with my Gen 2 Mendel P V3II (I say V3II because it has been extensively Modified over the years) I am having trouble making mine Home Z.
No matter what I do it still behaves like I have the endstop Triggers set wrong... no matter what I do I have checked the plugs and they are all in the right way. X and Y are fine. I know how Sprinter works and how to
by
Justinjjhcs1
-
Mendel90
anyone still admin this forum?
by
Justinjjhcs1
-
Slic3r
Do you need replacement parts for your PM? If so let me know I sell a Full set of PLA parts for 65.00 CND Shipping Included. most parts for this Home built 3D DIY you can get from your Hardware store. or Electronics parts shop. they can even be made from 3 or 4 scrap printers.
by
Justinjjhcs1
-
Plastic RepRap Parts for Sale
Still selling the Persa Mendle Variant I put together Next mod is a Pusher Extrude to prevent X axis Wobble. Will print you out parts you need for 5 Bucks plus 9 shipping. will use CPS. slow but they will arrive alive.
by
Justinjjhcs1
-
Plastic RepRap Parts for Sale
Ok Calibration for Merlin is compleatly different from Sprinter, I thought I could just Copy the Steps and Endstops. I cannot get Merlin to work for me as reliably as Sprinter.the Steps and every part of the Calculations are Totaly Different.
Sprinter
#define _AXIS_STEP_PER_UNIT {83, 83, 3200/1.25, 400}
Merlin
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200.0*8/3,760*1.1}
Yeah I know
by
Justinjjhcs1
-
RAMPS Electronics
it did but every correction led to another error... I just downloaded another version and found out where to stick the library updates problem solved.
by
Justinjjhcs1
-
General Mendel Topics
I was careful to install the LCD the right way around.... I had a Y axes Carriage Fail and a RAMPS SHIELD Fuse burn out on me too. Ill repair it with an Auto Fuse holder and check the diodes for damage but in the mean time I had to cannabis my other PM3 to get one running to make a new carriage, but then I just said why not get another extruder from A2AElectronics and save the hassle but I go
by
Justinjjhcs1
-
General Mendel Topics
Yeah I saw and corrected the 3 then I re-downloaded the hole thing Marlin_Marlinv1 AKA V3 and now it works but the steps per MM are wrong and the ((Actrualsteps/desired steps) *value in firmware code) dose not seem to work well with values like 78.987*1.75--- and that is not a Z value that is an X value.
by
Justinjjhcs1
-
General Mendel Topics
I am trying to install an LCD on my Persa Mendel I followed the Instructions on RepRap for Marlin V1 and It keeps giving my Errors I think the Definition of Variables is wrong in the Scripting I even tryed using the generic settings still nothing.
here is the LCD Script for marlin.
I need to know where the error is.
//LCD and SD support
//#define ULTRA_LCD //general LCD support, also 16x2
#defin
by
Justinjjhcs1
-
General Mendel Topics
Current wire Config
Don't you have to Reset the firmware
//-----------------------------------------------------------------------
// Inverting axis direction
//-----------------------------------------------------------------------
const bool INVERT_X_DIR = false;
const bool INVERT_Y_DIR = false;
const bool INVERT_Z_DIR = true;
const bool INVERT_E_DIR = false;
All True?
My bed is X 200mm Y 2
by
Justinjjhcs1
-
Repetier
I think I am having the same problem I have a Persa Mendel and the Y motor is at the Front of the Printer it is 0,0 at the back right of the Printer and the end-stops are set for the Low I think I keep getting a Backwards Print even though the part still works I feel it is Screwing up the Printing do I have to move my end stops to the Front right for the Y and Left for the X?
by
Justinjjhcs1
-
Repetier
Hello all I have acheaved my Goal of having a Working 3D Printer with No Donations
I will print you out a Full set of Plastic ABS Parts for a Printer for $50.00 Individual parts are the Cost of Plastic I will do them in PLA if you want. My build is 180mmX180mmX100mm
Red or white Even Pink.
Here is my site for my Persa Mendel Fund. If you live in Wastern Canada I will print in 3 days and you ca
by
Justinjjhcs1
-
Plastic RepRap Parts for Sale
Ill make you a Go Pro Mount for Nothing...
by
Justinjjhcs1
-
Calgary
or go to the Frame department of the Craft shop A mirror is good but you need Archive Glass it has been Annealed to withstand Temp Change
by
Justinjjhcs1
-
Calgary
are you still interested in Parts I have a Persa Mendel with roughly 180X180mm Build space and I will only charge the cost of ABS Plastic plus 10 Bucks. Depending on the Object and % of Solid.
by
Justinjjhcs1
-
Calgary
I found out my problem my Drivers are Fried I am Ordering new Drivers I cross connected the Motors to the Extruder driver and the Motor Moved... so Some of the Drivers are Fried and Maybe I have a corrupted Version of Arduino Down-loader it seems to work fine on my Older laptop.... but not on the More Powerful new one... So I will use the Old one for my 3D printer.
by
Justinjjhcs1
-
General Mendel Topics
Error Message when I try to compile and upload I have no SD card and the Script is now compileing because of this Problem
think I might have Fried my Electronics.... I did get the Script to Upload but there is no Movement.....
#define _AXIS_STEP_PER_UNIT {62.3, 62.3, 3200/1.41111,375}
by
Justinjjhcs1
-
General Mendel Topics
downloaded a Fresh copy and now It will not Compile or Upload to my Arduino Mega 2560 I have changed the Script in the way I have done 1000 times and now I get a Script Error that starts as soon as Arduino tool checks the Script.
Can anyone Help me?
by
Justinjjhcs1
-
Firmware - mainstream and related support
Page 1 of 2
Pages: 12