Show all posts by user
Page 1 of 1 Pages: 1
Results 1 — 22 of 22
Yeah me to. In 1993-94 I studied electronics watchmaking; prestigious watch testors power the part from the multimeter, so the exact consumption per h/sec was allowing to see battery use predisctions.
In my Kossel/arduino/ramps (discontinued) it was odd how precision was to be obtained. First see pic need a microscrew driver , during power on adjust the step motor feed to 0.350mili volt with a te
by
[email protected]
-
Prusa i3 and variants
Whatever works yeah after rp+yrs of microchip printing life would be easy by now in printing with extruders.
Why am I in wrong forrum?? I enjoy not finding my specific model
by
[email protected]
-
Prusa i3 and variants
I found cilicon lubricant works well for those slider bearings ( the propellant in can dissolves what seem's to have beeen oil from manufacturer that dried.
I suggest strap conditionner for squeeky straps in cars. It will (by brush to backside be little sticky byt prevent strap slipping. Not recommended on toothed side (more gunk for motor to tread through)
Cilicon, as your oil must be vegetal
by
[email protected]
-
Prusa i3 and variants
Heat control working on that now fluid mechanics for hot end, and most fun (missing fan RPM and CFM)
Fourier's law/newton's law of cooling for extruder jam's and heat conductivity to parts and /PLA/ABS, lastly Ohm's law for all electronics heat distribution
Ideally, a transparent garbage bag filled with CO2 isolate heats sources to where they should be applied (pla/abs bond after extrusion.
by
[email protected]
-
Prusa i3 and variants
I'm bad with arfuino site 6oo pages of forrum no complete how to guide.
My 1o$ multimeter/tester measures o.35 no thousanth decimal, and for consumption of electricity in moovement a testor must provide an exxact volt amp rate.
We simply lack programming skills to compensate for a real ohm's law mechanical issue.
Open source is messages like this with few solutions to shelf in your own homw. Yea
by
[email protected]
-
Prusa i3 and variants
That was easy, mine had bond fee 0lane hier than ground brokerage fee... Internationnal sales of shipping did not include foren taxes, shipper paid an bingo EXTRA7o$. Dan's gone? Shipper acknowledges the fee could be waved because the location of pickup Foldgerteck us had old soft could not inform folgerteck the fee uppon ship.
No scam there, just an internet lookup to find taxes, and a www sit
by
[email protected]
-
Prusa i3 and variants
[email protected]
This file would be good for pimped my ride kind of show.
Imagin mounting your electronics in a transparent gerrycan and have fluorescent cooling non conducting fluids, fanned with bubles ). I call my. Projects landing a can on a plate.
P.S.: would love to post my build experience as I recall and embellish it to 2015 festive games time Toronto sports.
Competitors here
by
[email protected]
-
Prusa i3 and variants
This file would be good for pimped my ride kind of show.
Imagin mounting your electronics in a transparent gerrycan and have fluorescent cooling non conducting fluids, fanned with bubles ). I call my. Projects landing a can on a plate.
by
[email protected]
-
Prusa i3 and variants
Try the links for setting on this engineers blogs
or search Richard Horne (RichRap) is an Electronics Engineer, Product Designer, Salesman, and Problem Solver working in a wide range of industries and applications, across many platforms and technologies for the last 20 years.
Lots of articles on settings in slic3r
by
[email protected]
-
Canada, Toronto RepRap User Group
Kossel 2020 Full 3D Printer Kit w/Auto-Level
-
-List of filament to etruder nosle heat loss per mm/sec
-step by step X,Y,Z callibration for dummies (used level on plate
-Followed all setings from fabricant ok
could open source have setting packs named to printer models?
-Must read disorganised info on www sites, is nothing compiled into text files for ofline reading/studying
.Back to Arduino.cc
by
[email protected]
-
Mechanics
Still configuring , faulted circut, then shorted USB 8foot, then Arduino out of stock mega 2560 r3.
Working on understanding X;Y,Z callibration, some how stopped being able to update arduino, must figure out how to export message errors, found tip in troubleshooting at arduino (short set some setting and the rest are faulted)
35$/euro mistake tripped on usb eh.
Crash during calibration, sitting
by
[email protected]
-
Mechanics
Find motor power needed, neasure weight of parts (tada)
This is the good technical stuff if your printer extrudes and advances with calibrated mesurable data.
My kit is new, I turtured it. I have a technical background, an uncle told me 'i don't understand I follow datasheets" and repaired electronics. Studied electronic watchmaking, have a diploma had many manual experiences, hobby lover,
by
[email protected]
-
Mechanics
That was new! Eh next time I'll get it to engrave my full signature
Yeah open source read all info before usage, and it's all online not included with the software you download in many cases, found it hard to stay relevant, might just be a vocabulary thing.
Maybe a good book from sybex...
by
[email protected]
-
Canada, Toronto RepRap User Group
Same here software calibration to get solid bond on extruder layers.
Some terminology changes from one soft to another , so as a newbie my kessel. Brings me to think hey algebra was fine for electronics but this. XYZ axis thing diametre, vs isometric drawing is like calculus (I skipped that for trades )
Hehe
So help with settings to slic3r and pronterface. I HAVE to meanwhile remove material
by
[email protected]
-
Canada, Toronto RepRap User Group
Canadian tire main store has 1kg 3colours 1.75 filament brand dremmel 36$
Walmart is selling 3D printers too... See the online prices varry in shipping..
I WANT wax filament to make castings... The conductive filament to after print do electroplating
Currently it's like 175$ for dipping solutions to coat the abs with conductive layer.
by
[email protected]
-
Canada, Toronto RepRap User Group
I HAVE Arduino - 1.6.4 it will help load the cards it supports (open source free soft)
Ummm not femilliar with your product but it's worth a try, I downloaded schematics and many informative how to's.
Even a bread board setup...
Also chech sparkfun electronics they have all the board accessories hardware and courses, ect
That's all I have as a newbie, hope this helped.
by
[email protected]
-
Canada, Toronto RepRap User Group
Just finished my Kossel 2o20 from Folgertech and have lots reading to do
Like following the Folgertech Kossel configuration manual then having to configure pronterface then slic3r...
Tried. Quick print after first document drove the nosel right into the aluminum heating plate 2x nosel got clogged, but I happen to have o.39 drill bits and smaller .
Open source is my eniigma, as most informative m
by
[email protected]
-
Canada, Toronto RepRap User Group