Show all posts by user
Группа Пользователей RepRap
Re: Pronterface Missing -Z Jog Option? - 10 months ago
... there was no negative indication on the Z-jog or XY ... it will move into only one axis direction, if it's not homed correctly or outside of the "allowed" moving range. Here a screenshot of my old modified Pronterface from arond 10 years ago:by VDX - Printrun/Pronterface
Re: Pronterface Missing -Z Jog Option? - 10 months ago
... IIRC, you can set an offset in the firmware and you can define the "home" coordinates in pronterface too ... didn't work with it some years now ...by VDX - Printrun/Pronterface
Re: Pronterface Missing -Z Jog Option? - 10 months ago
... you have to configure the axes directions and switch-positions (min/max and eventually inverting the switches) accordingly to your setup, otherwise it can show such behaviour.by VDX - Printrun/Pronterface
Re: Pronterface Missing -Z Jog Option? - 10 months ago
... check for the ref-button-status with "M119" - if not "homed" for Z or still triggered status, then it runs only in one direction ...by VDX - Printrun/Pronterface
Re: IPG Lasersystem - Pulsed Ytterbium Fiber Laser (2007) Hilfe - 10 months ago
... wenn du das mit einem E1701D aufbauen willst - die Software BeamConstruct von HALaser ist kostenlos (nutzt den Controller als "Dongle") - hier die features - Der Controller selber kostet je nach Aufbau (mit zusätlichen CNC-Achsen und I/O's) glaube inzwischen um 800€ - ich hatte den Anfangs noch für 600€ bekommen ... hab' auch noch ein paar Varianten davon (z.B. für einen XY-Plotter mit eineby VDX - Laser-Ecke
Re: IPG Lasersystem - Pulsed Ytterbium Fiber Laser (2007) Hilfe - 10 months ago
... zur Reparatur eines propriäteren chinesischen Controllers kann ich dir auch nicht helfen ... solltest du dir aber selber einen aufbauen wollen, kann ich dir ggf. ein paar Tips und Links geben. In "meinen" Faserlasern habe ich jeweils den Controller E1701D von HAlaser drin, welcher auch die IPG-Faserlaser direkt ansteuern kann ... zur Not könnte ich den IPG auch probeweise an einen meiner Conby VDX - Laser-Ecke
Re: M42 in old Marlin 1.1.x - 10 months ago
... I'm remembering something like "M42 P2 S255" for activating a Pin D2 (and accordingly "... S0" to deactivate)by VDX - General
Re: Monster8 - Marlin 2.1.2.1 Configuration for XYZE0E1AUV + Laser cooling - 10 months ago
... this was some 10+ years ago and I've done most of the developing and programming then too "on my own" ... so actually no active programmers available around.by VDX - Developers
Re: Monster8 - Marlin 2.1.2.1 Configuration for XYZE0E1AUV + Laser cooling - 10 months ago
... my "high power"-lasers and tinkering with the broken fiber-lasers and salvaged laserdiodes is all hobby - in my job I'm developing different applications for "laser assisted material transfer" with UV-DPSS- and "ultra-short-puls"-lasers ... they have 20W averaged. Some years ago, when developing jetting paste-dispensers, I've used Marlin4Due together with Pronterface/Printrun to control theby VDX - Developers
Re: Monster8 - Marlin 2.1.2.1 Configuration for XYZE0E1AUV + Laser cooling - 10 months ago
... I'm from Germany The housing in the images is from a 50 Watt CW fiberlaser - have several with different wreckage types ... some with exploded fiber-couplings for backreflection ... some with broken electronics (one with 130Watts is emitting fine, when supporting the diodes with current only) ... some with cut external fiber ... They are all air-cooled - the housing is a "sandwich" of twoby VDX - Developers
Re: Monster8 - Marlin 2.1.2.1 Configuration for XYZE0E1AUV + Laser cooling - 10 months ago
... for the "medium size" diodes I'm too using peltiers - here I've reworked a fiber-laser housing with 4 ventilators into a peltier-heat-exchanger with 6x 30Watt PZT-modules. Here some images of the setup with 2 of the diodes and 3x Peltiers under every diode and a 10mm alu sheet for heat-distributing ... for an ambien temp. of around 20degC the emitted hot air will be at around 55 to 60degC atby VDX - Developers
Re: 3D-Scanner zum Einstieg gesucht - 10 months ago
... ob der gute Mann den Scanner nach nun 7 Jahren immer noch sucht?by VDX - 3D-Scanner
Re: Monster8 - Marlin 2.1.2.1 Configuration for XYZE0E1AUV + Laser cooling - 10 months ago
Quotelukaari How much of the coolng power you actualy need for the lasers? ... this depends - the small modules around 50W, the DPSS-lasers 800 to 1000W (up to 1kW) ...by VDX - Developers
Re: Monster8 - Marlin 2.1.2.1 Configuration for XYZE0E1AUV + Laser cooling on the chamber pin - 10 months ago
... depending on the needed cooling power (I have some laserdiodes or lasers with up to 1kW needed for proper cooling) you can think about stand-alone coolers, as common used for water-cooled lasers (one of my water-coolers has 1.5kW)by VDX - Developers
Re: Laserdioden werden immer stärker - wofür verwenden? - 10 months ago
... die nächste "Eskalationsstufe" - 310Watt @975nm bei 43 Ampereby VDX - Laser-Ecke
Re: Thermoset Type Plastics used in a extrusion type printer? - 10 months ago
... repeated melting plastic materials will degrade them - so maybe better working with solvents or lower temps. One of my related ideas was to laser-sinter dark plastic powders or lignin-powder (have some from Tecnaro)by VDX - Polymer Working Group
Re: Relay 5v wont go off - 10 months ago
... look into the datasheet for common use/schematics -- sometimes you'll need resistors or a specific polarity of the transistor/mosfet ...by VDX - General
Re: Need signal when printing finished. - 10 months ago
... to get all available pins you can use "M43" - Which pins are assigned to your actual configuration should be found in the documentation to your board ...by VDX - General
Re: New to the forum, greetings and questions - 10 months ago
... there could be some RADDS boards available -by VDX - General
Re: Need signal when printing finished. - 10 months ago
... read into the G-code "M42" -by VDX - General
Re: Thermoset Type Plastics used in a extrusion type printer? - 10 months ago
... check for "hot melt dispensing", as shown here (look at the video too) - This could be ued with "filled" materials too ...by VDX - Polymer Working Group
Re: DIY printhead - 10 months ago
... check the date of the last post ... seems quite old, so maybe no reaction to awaitby VDX - Powder Printing and Selective Laser Sintering
Re: Voron 2.4 mit RepRap - 11 months ago
... wie schon geschrieben - warte noch ein Bischen, ob/wann sich jemand meldet, der sich mit deinem Drucker bzw. der Ansteuerung besser auskennt. Ich habe meine noch Alle mit Pronterface/Marlin mit den Arduino-Boards (oder Marlin4Due mit ArduinoDue) und als Drucker auch eher ältere Typen (Darwin- und Mendel-Varianten, Orca, Eigenbau) ... und mich auch schon länger nicht mehr mit Kunststoff-FDM-3by VDX - Allgemeines
Re: Voron 2.4 mit RepRap - 11 months ago
... das RepRap-Projekt wurde 2006 gestartet und die "aktivste Zeit" ging von etwa 2007 bis 2011, bis sich das Thema ausreichend weit rumgesprochen hatte ... danach haben die Chinesischen Copy-Cats "übernommen" und die eigentlichen Entwickler hatten nicht mehr so die Lust, ihre in den Foren vorgestellten Open-Source-Entwicklungen nach ein paar Monaten als (schlechte) Kopien bei Alibaba oder Amazonby VDX - Allgemeines
Re: Voron 2.4 mit RepRap - 11 months ago
Hallo Daniel, ... willkommen bei RepRap! Nachdem die "aktive" Zeit schon etwas her ist, ist es hier im Forum etwas ruhiger geworden, die Antworten könnten also etwas länger dauern. Noch ein Tip fürs Suchen in den Foren - ganz unten in der rechten Combo-Box "jeden Alters" auswählen, sonst wird nur über die letzten 30 Tage gesucht ...by VDX - Allgemeines
Re: Please delete my account - 11 months ago
... done ...by VDX - Administration, Announcements, Policy
Re: Two different home positions - 11 months ago
... check the settings in your configuration and if you have some different G-codes in a pre-/post-macro. You have to define yhe position of the limit-/homing-switches and the seeking direction for homing accordingly ...by VDX - Firmware - Marlin