Hi, The following code control an LCD I can make it work on a arduino uno with the default pin rx(0)-tx(1): How to use the aux-1 on my RAMPS to do the same program? #include void setup() { // put your setup code here, to run once: pinMode(13,OUTPUT); Serial.begin(9600); } void loop() { // put your main code here, to run repeatedly: //envoyer image 0 à p0: 2 seconde : digitalWrite(13,HIby TechMage - RAMPS Electronics
thx everyone I found the problem. Yap the motor shaft was loose. Jasonby TechMage - General Mendel Topics
Thx for your advise jcrbrer but its the motor that doesn't move move correctly. Now its not working in the extruder tab either. (software)by TechMage - General Mendel Topics
Hi, My mendel seem to work fine. But during the printing the extruder motor don't push the plastic in the extruder its just moving up and down i'm not sure what to do. It's working when I go to the extruder tab just not when I do a print. Jasonby TechMage - General Mendel Topics
Hi, When I start the reprap I heat the extruder and then wait for 190 C. After I start the printing everything is moving correctly but the extruder stop heating and the plastic solidify. Can you help me? I'm using Techzone Gen 3 remix electronic and Software version 20100806 Jasonby TechMage - Controllers
Hi, When I load a gcode, Heat the extruder and press print the reprap go from the lower left corner to the upper-left corner then to the upper-right and finally in the lower-right. After, it just stops moving and the extruder motor is making sound, but it's not moving. Can someone help me? All the axes and the extruder are working individually. I'm using gen 3 electronic (remix) from techzone Jby TechMage - Reprappers
I think openscad will work I just need to learn how to use the program thx guys Jasonby TechMage - 3D Design tools
Hi, I try a some freeware I found but none of them allow you to enter an equation (parabolic, hyperbolic...) to create the basic form and then make the modification, its all manual. If I want to create a complex form is there an other solution then take the equation extrapolate the points, draw a polygon an place the points one by one ? Any freeware or low cost software can do this (and export/bby TechMage - 3D Design tools
Hi, When the extruder reach 170 C it stop heating up (and the ramping stop too) and even if i click back on ramping it did'nt work. The target temperature is 190 C. I also try target temperature at 210 C its shuting down at 190 C. Always 20 degree below. Someone can help me? I'm using Gen3 electronic Jasonby TechMage - Controllers
electronic: Techzone Gen3 And the firmware is 20100719by TechMage - Firmware - mainstream and related support
I just found a file (pins.h) I ave atmega644 so I will try to change that line: #define EXTRUDER_1_HEATER_PIN (byte)24 for: #define EXTRUDER_1_HEATER_PIN (byte)15 Please tell me if you think I'm not doing the right thing.by TechMage - Firmware - mainstream and related support
Hello everyone, I just burn out the mosfet on A+/A- (and a power supply) I would like to now how to change the firmware so it use the second mosfet. So far I found this picture: I guess I have to change pin A1 for D11 somewhere in the program. thanks TechMageby TechMage - Firmware - mainstream and related support
Hello DelarnLeviathan, I'm not sure I understand your question complitely you can see exemple of printed object at thingiverse. The precision is around .5 mmby TechMage - Canada, Montreal RUG
Hello tout le monde, Je construis une reprap en se moment, la partie mécanique est presque terminée. Et je devrais commander l'électronique la semaine prochaine.by TechMage - Canada, Montreal RUG