https://reprap.org/mediawiki/api.php?action=feedcontributions&user=Merlucin&feedformat=atomRepRap - User contributions [en]2024-03-29T05:02:35ZUser contributionsMediaWiki 1.30.0https://reprap.org/mediawiki/index.php?title=TMC2100&diff=181865TMC21002018-03-20T17:39:55Z<p>Merlucin: /* Sources and where to get it: */</p>
<hr />
<div>{{Languages}}<br />
{{Development<br />
<!--Header--><br />
|name = TMC2100<br />
|status = working<br />
<!--Image--><br />
|image = TMC2100_preview.jpg<br />
<!--General--><br />
|description = TMC2100 stepper motor driver<br />
|license = [[CC-BY-SA]]<br />
|author = Skimmy<br />
|reprap = unknown<br />
|categories =<br />
{{tag| surface-mount electronics}};<br />
{{tag| stepper motor drivers}};<br />
{{tag| Electronics}};<br />
|cadModel = [https://github.com/watterott/SilentStepStick github.com/watterott/SilentStepStick Eagle source files]<br />
|url = <br />
}}<br />
TMC2100 are the quietest Pololu compatible stepper motor drivers currently available on the market. The size corresponds to the popular Pololu drivers: the pinout is compatible, but not identical. The driver can be used on all major electronics, eg 8-bit electronics as RAMPS, Rumba, GT2560 or 32-bit electronics as RADDS or AZSMZ and all other Pololu compatible RepRap electronics.<br />
<br />
==Specification==<br />
<br />
*Driver-IC: [https://www.trinamic.com/products/integrated-circuits/details/tmc2100/ Trinamic TMC2100], noiseless operation (in certain modes)<br />
*Hardware compatible with Step Stick and Pololu A4988<br />
*1.25A RMS '''continuous current''' (equivalent to about 1,77A I<sub>max</sub>)<br />
*'''short-time''' peak current 2.5A per motor coil<br />
*Motor voltage: 5.5 - 46V or 4.75 - 46V (5V SilentStepStick) <br />
*Step/Dir interface with micro-step function (interpolation of up to 256 micro-steps)<br />
*automatic standby current reduction<br />
*stealthChop mode - for a noiseless operation<br />
*spreadCycle mode - for a high dynamic and torque<br />
<br />
==Special features in comparison to other stepper motor drivers==<br />
<br />
The TMC2100 stepper motor drivers a few peculiarities must be observed.<br />
<br />
*The driver board is "upside down" mounted, with the chip and the potentiometer down. To allow this, the pinout is mirrored too.<br />
*The heat sink is mounted on the circuit board on the back. This is much better, because the heat is much better guided by the vias (heat pipes) of the board, than the thick plastic layer of the chip itself.<br />
*The potentiometer is mounted upside down and adjustable via a hole through the board.<br />
*The "stealthChop" operating mode is noiseless and suitable for most cases (except a 3D printer extruder). It can lead to step losses since the torque is considerably reduced. If you have problems like step losses then you can use a slower acceleration or you can use the more powerful spreadCycle mode.<br />
*The "spreadCycle" operating mode gives more torque, but is not completly noiseless.<br />
<br />
==Pin Configuration==<br />
<br />
Since many different electronic boards available such as RAMPS, RADDS, RUMBA, etc, the wiring of config pins (CFG1, CFG2 and CFG3) is solved differently, so it's recommended not to connect config pins. This prevents that change of the electronics implies adjusting the driver. Be joined, that the "spreadCycle" mode also needs the pin CFG1 connected to GND. This can be realized by a small wire bridge (see photo).<br />
<br />
Some Chinese boards have been seen in the wild that have CFG1-3 printed out of order on the bottom of the PCB. So CFG3 is connected to MS1 and is actually CFG1 (see photo). Because the configuration pins ship open, you must close them by bridging with solder as shown in the photo in addition to connecting MS1 to GND.<br />
<br />
The pins and DIAG1 DIAG2 have no function and may also be omitted.<br />
<br />
Various operating modes to provide a through connection of the 3 config pins that green highlighted lines are the recommended operation modes:<br />
<br />
{| class="wikitable"<br />
|-<br />
! CFG1 !! CFG2 !! Schrittteilung !! Interpolation !! Mode<br />
|-<br />
| GND || GND || 1 (full step) || none || spreadCycle<br />
|-<br />
| VCC || GND || 2 (half-step) || none || spreadCycle<br />
|-<br />
| open || GND || 2 (half-step) || 256 µ-Schritte || spreadCycle<br />
|-<br />
| GND || VCC || 4 (quarter-step) || none || spreadCycle<br />
|-<br />
| VCC || VCC || 16 µ-steps || none || spreadCycle<br />
|-<br />
| open || VCC || 4 (quarter-step) || 256 µ-steps || spreadCycle<br />
|- style="background:lightgreen" <br />
|GND || open || 16 µ-steps || 256 µ-steps || spreadCycle<br />
|-<br />
| VCC || open || 4 (quarter-step) || 256 µ-steps || stealthChop<br />
|- style="background:lightgreen" <br />
| open || open || 16 µ-steps || 256 µ-steps || stealthChop<br />
|}<br />
<br />
==Images==<br />
<br />
{| width="90%" align="center"<br />
| [[File:TMC2100_Schematic.png | center | thumb | circuit diagram]]<br />
| [[File:TMC2100_Schematic_simple.png | center | thumb | wiring diagram]]<br />
| [[File:TMC2100_CFG_PINS.png | center | thumb | CFG Pins]]<br />
| [[File:TMC2100_boardlayout.jpg | center | thumb | pin assignment]]<br />
|-<br />
| [[File:TMC2100_spreadcycle_topview.jpeg | thumb | top view (spreadcycle)]]<br />
| [[File:TMC2100_spreadcycle_bottomview.jpeg | thumb | bottom view (spreadcycle)]]<br />
| [[File:TMC2100_Vref_pins.jpeg | thumb | Vref pins]]<br />
<br />
|-<br />
|[[File:TMC2100-chinese-cfg1-bottom.png | thumb | bottom view (spreadcycle, mislabeled chinese pcb solder bridge)]]<br />
|[[File:TMC2100-chinese-cfg1-top.png | thumb | top view (spreadcycle, mislabeled chinese pcb)]]<br />
|}<br />
<br />
==Setting the reference voltage / motor current==<br />
<br />
The best way to adjust the motor current, the voltage at V<sub>ref</sub>-Pin (0 - 2,5V)to measure and then adjust the potentiometer. The maximum continuous current is 1,25A (I<sub>rms</sub>) or 1,77A (I<sub>max</sub>) and is determined by the 0,11Ω-sense resistor.<br />
<br />
Chinese PCB's have been reported with a 6.8k Ohm potentiometer instead of 20k. This limits the maximum current significantly.<br />
<br />
These steppers require active cooling over Vref voltages of around 0.55.<br />
<br />
'''Formulas for calculating the values:'''<br />
<br />
I<sub>rms</sub> = (V<sub>ref</sub> * 1.77A) / 2.5V<br />
<br />
I<sub>rms</sub> = V<sub>ref</sub> * 0.71<br />
<br />
I<sub>max</sub> = 1.41 * I<sub>rms</sub><br />
<br />
V<sub>ref</sub> = (I<sub>rms</sub> * 2.5V) / 1.77A<br />
<br />
V<sub>ref</sub> = I<sub>rms</sub> * 1.41<br />
<br />
V<sub>ref</sub> = I<sub>max</sub><br />
<br />
<br />
'''Example:''' <br />
A voltage of 1.0V at the VREF pin sets the motor current to 0,71A I<sub>rms</sub> / 1A I<sub>max</sub>.<br />
<br />
V<sub>ref</sub> = (I<sub>rms</sub> * 2.5V) / 1.77A <br />
<br />
1V = (0,71A * 2.5V) / 1.77A<br />
<br />
'''Please note:''' In some stepper motor drivers, such as the A4988, it represents the maximum current (Imax) with other the RMS current (Irms), such as the TMC2100.<br />
<br />
==Further information==<br />
<br />
Github: [https://github.com/watterott/SilentStepStick SilentStepStick]<br />
<br />
Summary PDF: [[File:SilentStepStick_v1.0_summary.pdf]]<br />
<br />
==Sources and where to get it:==<br />
<br />
[http://www.watterott.com/en/SilentStepStick TMC2100 SilentStepStick (3-5V) at watterott.com] DE<br />
<br />
[http://www.watterott.com/en/SilentStepStick-TMC2100-5V TMC2100 SilentStepStick (5V) at watterott.com] DE<br />
<br />
[http://stepstick.pl/?58,pl_sterownik-silnika-krokowego-silent-stepstick-tmc2100-(watterott) TMC2100 SilentStepStick (3-5V) at stepstick.pl] PL<br />
<br />
[https://e3d-online.com/tmc2100 TMC2100 SilentStepStick (5V) at e3d-online.com] UK<br />
<br />
[https://www.filastruder.com/products/silentstepstick-tmc2100-stepper-motor-driver TMC2100 SilentStepStick (3-5V) at filastruder.com] USA<br />
<br />
'''Clones (no schematics available):'''<br />
<br />
[https://orballoprinting.com/en/home/174-tmz-2100.html TMC2100 SilentStepStick at orballoprinting.com] ES<br />
<br />
[https://www.robotdigg.com/product/944 TMC2100 SilentStepStick at robotdigg.com] CN (will charge lots for shipping, theres a reason they don't list shipping rates)<br />
<br />
[http://store.thingibox.com/en/mechanical/268-driver_TMC2100_256_microsteps.html TMC2100 SilentStepStick at Thingibox.com]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Prusa_i3_ION/es&diff=181788Prusa i3 ION/es2018-02-28T16:02:01Z<p>Merlucin: /* Introducción */</p>
<hr />
<div>{{Languages}}<br />
<br />
{{Development<br />
<!--Header--><br />
|name = Prusa ION V6<br />
|status = working<br />
<!--Image--><br />
|image = Prusa i3 ION.PNG<br />
<!--General--><br />
|description = <br />
|reprap = Prusa i3<br />
|license = [[GPL]]<br />
|author = ThingiBOX<br />
|categories =<br />
[[:Category:Prusa i3|Prusa i3]],<br />
{{tag|Prusa i3 Development}},<br />
{{tag|Prusa Mendel Development}},<br />
{{tag|Prusa Mendel}},<br />
{{tag|Mendel Variations}},<br />
{{tag|Cartesian-XZ-head}}<br />
|CAD Models = https://github.com/Thingibox<br />
|External Link = http://store.thingibox.com/es/22-ion-v6<br />
}}<br />
<br />
<br />
=Introducción=<br />
[[Image:Prusai3 ION Front.jpg|thumb|300px|left|Prusa ION V6]]<br />
<br />
::La '' 'Prusa ION V6' '' es una impresora 3D inspirada en el Prusa i3, pero con muchos cambios, mejoras y actualizaciones. Ha sido diseñado por el equipo técnico de [http://store.thingibox.com ThingiBOX], una tienda en línea cuyos productos están relacionados con el mundo de la impresión 3D.<br />
<br />
::El objetivo del proyecto era diseñar una estructura hecha con metacrilato donde todas las partes estuvieran cortadas con una máquina láser CNC, el otro objetivo era mantener todos los componentes electrónicos dentro de la impresora para que se viera limpia y ordenada. Para facilitar el enfriamiento de la electrónica, hay instalados dos ventiladores.<br />
<br />
:: El volumen máximo de impresión es de 200x200x150mm en una cama calefactada de acero con una base de silicona y encima de un vidrio de borosilicato (preparado para el cambio abrupto entre las temperaturas), por lo que se puede imprimir con ABS sin ningún problema (si se aplica laca).<br />
<br />
<br><br><br><br><br />
<br />
::El extrusor es un v5 E3D de metal que puede calentar hasta 300 ºC. En esta impresora se pueden utilizar todo tipo de material plástico (ABS, PLA, etc.) disponible en el mercado. Existe la opción de elegir el diámetro del filamento que admite la extrusora, por lo que lo ofrecemos en 3 mm o 1,75 mm. La boquilla tiene un orificio de 0,4 mm en ambos casos.<br />
<br />
::También hay un ventilador (y su soporte) para el radiador de la extrusora cuya función es evitar que el filamento obstruya el conducto.<br />
<br />
::Para impulsar el filamento, hay una rueda dentada que aumenta la fuerza que puede hacer el paso a paso e impulsa un perno con tuerca MK8.<br />
<br />
:: Para el eje Z (la altura) contiene las barras Tr8x8 porque eso mejora la calidad de impresión significativamente.<br />
<br />
:: Para el movimiento de los otros dos ejes se utilizan poleas GT2 y correas síncronas.<br />
<br />
:: Para la electrónica; Se usa un Arduino MEGA 2560 junto con una RAMPAS 1.4, que también incluye 4 controladores A4988 que manejan 5 motores paso a paso NEMA17. También se incluyen 2 interruptores de fin de carrera y un sensor capacitivo para hacer el autohome de los ejes automáticamente y el autocalibrado.<br />
<br> <br> <br><br />
:: Para dar la potencia necesaria también se proporciona una fuente de alimentación que emite 12 V y 5 A (60 W) ya que la base caliente se contecta a 220V y no consume amperaje. <br />
<br />
:: Los cables que están fuera de la base de la impresora están confinados en una cadena de cable para protegerlos durante el movimiento del eje y para que quede todo ordenado.<br />
<br />
:: En la parte posterior de la base hay dos conectores, uno para conectar con el interruptor de alimentación de CA y un conector USB integrado. También tiene un espacio si desea conectar una Raspberry Pi (no incluida) para controlar la máquina con Ocotprint a través de Internet.<br />
<br />
:: También se incluye una LCD 2004 que incorpora un lector de tarjetas SD, para poder controlar la impresora y imprimir piezas directamente desde la pantalla.<br />
<br />
= Datos técnicos =<br />
<br />
{| class="wikitable sortable" border="1" align="center"<br />
|-<br />
| Marco || Metacrilato blanco 8 mm metacrilato transparente 5 mm<br />
|-<br />
| Varillas lisas || Acero 304, tolerancia H9<br />
|-<br />
| Varillas roscadas || Subproceso Tr8x8 <br />
|-<br />
| Volumen de impresión || 200x200x150 mm<br />
|-<br />
| Extrusora || E3D v5 (Todo de metal)<br />
|-<br />
| Diámetro del filamento || 1.75 / 3 mm (opcional)<br />
|-<br />
| Tipos de filamentos || Todos los tipos (PLA, ABS, Nylon, etc.)<br />
|-<br />
| Electrónica || Arduino MEGA 2560 - RAMPAS 1.4<br />
|-<br />
| Controladores || 4 x A4988<br />
|-<br />
| Fuente de poder || 12V / 5A<br />
|-<br />
| Plataforma de compilación || Cama de acero con base de silicona ( 220 V)<br />
|-<br />
| Display || LCD 2004 con lector de tarjetas SD<br />
|}<br />
<br />
== Documentación ==<br />
* [http://es.docs.thingibox.com/ Manual de montaje]<br />
* [https://github.com/Thingibox/ThingiBOX_Marlin Firmware configurado]<br />
* [https://github.com/Thingibox/Prusa-i3-ION/tree/master/Slic3r_Configuration Configuración del perfil de slic3r]<br />
<br />
= Funciones =<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION axial fans.jpg|150px|thumb|Ventiladores axiales]] ||<br />
:: A diferencia del Prusa i3 original, nuestra versión tiene una abertura para la electrónica y la fuente de alimentación de la impresora. Gracias a la carcasa, los componentes electrónicos, como los paneles de control, la fuente de alimentación, los cables y los conectores, se guardan de forma ordenada y segura.<br />
<br />
:: Dos pequeños ventiladores axiales asegurarán la refrigeración de los componentes electrónicos. La fuente de alimentación cuenta con un control de temperatura incorporado que corta la energía eléctrica en caso de sobrecalentamiento.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Alu-Sili.jpg|150px|thumb|Cama caliente]] ||<br />
:: El volumen máximo de impresión es 200x200x190mm. Los objetos están impresos en un vidrio de borosilicato de 3 mm de espesor que presenta una baja expansión térmica. Debajo del vidrio, colocamos una cama calefactada de acero que proporciona rigidez adicional y al mismo tiempo permite imprimir filamentos que presentan problemas de adherencia al imprimir a baja temperatura, como el ABS.<br />
<br />
:: Dependiendo de las condiciones de humedad y la temperatura ambiente, la cama calentada puede alcanzar una temperatura de 130ºC.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION extruder.jpg|150px|thumb|Extrusora]] ||<br />
:: La extrusora es un hotend de metal completo E3D v5 que permite imprimir a temperaturas tan altas como 300ºC. Es compatible con casi todos los filamentos disponibles. La boquilla tiene un diámetro de 0.4 mm, esto es un compromiso entre la precisión de impresión y la velocidad.<br />
<br />
:: Un ventilador adicional evita que el filamento se derrita antes de tiempo y obstruya el conducto. La extrusora incorpora componentes estándar y puede desmontarse por completo; esto facilita la limpieza y los reemplazos de repuestos.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION MK8 drive gear wheel.jpeg|150px|thumb|MK8 rueda dentada]] ||<br />
:: El ION Prusa i3 usa una rueda dentada de transmisión MK8 para alimentar el filamento en la extrusora. La rueda se fija en un eje con un engranaje en un extremo que aumenta en un factor cinco la potencia que se transmite por el motor. De esta forma, podemos usar un motor más pequeño en la extrusora, reduciendo la inercia del motor y aumentando la calidad de impresión al mismo tiempo. Esto se aplica especialmente cuando la extrusora cambia repentinamente su velocidad, por ejemplo cuando se imprimen esquinas.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION Z axis.jpeg|150px|thumb|eje Z]] ||<br />
:: Para el eje Z (que es responsable de levantar el cabezal de la impresora), contiene las barras roscadas Tr8x8 porque mejoran considerablemente los resultados de impresión. Las barras métricas tradicionales, no calibradas son significativamente menos costosas, pero pueden causar ondas en el objeto impreso que son más visibles en el taller del objeto.<br />
<br />
:: Con las barras Tr8x8 empleamos tuercas POM maquinadas que eliminan completamente la barra invertida, típica en las configuraciones tradicionales de barras roscadas. Para una precisión aún mayor, nuestras tuercas POM son 10 mm más largas que las tuercas habituales.<br />
<br />
:: Para el movimiento del otro eje de la impresora utiliza GT2 síncrono y cinturones con tensores manuales.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION electronics.jpg|150px|thumb|Arduino MEGA 2560]] ||<br />
:: En cuanto a la electrónica, esta impresora incluye un controlador Arduino MEGA 2560 junto con una pantalla RAMPS 1.4 que incorpora 4 controladores A4988 que mueven 5 motores paso a paso NEMA17. También se incluyen 2 interruptores de final de carrera con cable y un sensor capacitivo para hacer el autohome y la auta calibrción.<br />
<br />
<br />
:: Los cables externos de la impresora se mantienen en una cadena de cable. De esta forma, los cables se mantienen ordenados y seguros mientras el eje se mueve.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION socket.jpeg|150px|thumb|Toma con interruptor]] ||<br />
:: Dos conectores se encuentran en la parte posterior, uno para la fuente de alimentación de CA a través de un zócalo con interruptor y uno para conexiones USB en caso de que desee controlar la impresora directamente desde su PC.<br />
<br />
:: La carcasa también cuenta con una abertura y perforaciones para una Raspberry Pi 2 (no incluida) que permite conectar la impresora a Internet y controlarla a través de Octoprint.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION LCD.jpeg|150px|thumb|Pantalla LCD 2004]] ||<br />
:: Viene incorporada una pantalla LCD 2004 para monitorear la impresora. El controlador de pantalla incluye una tarjeta SD que permite cargar diseños sin necesidad de una PC.<br />
<br />
:: No hay necesidad de modificar el firmware para la configuración de la pantalla. Con esta placa puede controlar la velocidad de impresión sin tener que esperar que el hotend se enfríe, precaliente la impresora, modifique los parámetros del firmware o cambie el filamento en el medio del proceso de impresión; todo esto sin una PC<br />
| -<br />
|}<br />
<br />
=Otras versiones=<br />
<br />
También se encuentra disponible una versión XL con una superficie de impresión de 200x300<br />
<br />
=Dónde Comprar=<br />
<br />
- [http://store.thingibox.com/es/ion-v6/373-ION_v6_kit_completo.html Kit completo de la Prusa ION V6 en ThingiBOX] Ya a la venta!</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Prusa_i3_ION&diff=181787Prusa i3 ION2018-02-28T16:00:54Z<p>Merlucin: </p>
<hr />
<div>{{Languages}}<br />
<br />
{{Development<br />
<!--Header--><br />
|name = ION V6<br />
|status = working<br />
<!--Image--><br />
|image = Prusa i3 ION.PNG<br />
<!--General--><br />
|description = 3D printer inspired in the Prusa i3<br />
|reprap = Prusa i3<br />
|license = [[GPL]]<br />
|author = ThingiBOX<br />
|categories =<br />
[[:Category:Prusa i3|Prusa i3]],<br />
{{tag|Prusa i3 Development}},<br />
{{tag|Prusa Mendel Development}},<br />
{{tag|Prusa Mendel}},<br />
{{tag|Mendel Variations}},<br />
{{tag|Cartesian-XZ-head}}<br />
}}<br />
<br />
<br />
=Introduction=<br />
<br />
[[Image:Prusai3 ION Front.jpg|thumb|300px|left|Front image Prusa i3 ION]]<br />
<br />
::The '' 'Prusa ION V6' '' is a 3D printer inspired by the Prusa i3, but with many changes, improvements and updates. It has been designed by the technical team of [http://store.thingibox.com ThingiBOX], an online store whose products are related to the world of 3D printing.<br />
<br />
:: The objective of the project was to design a structure made of acrylic where all the parts were cut with a CNC laser machine, the other objective was to keep all the electronic components inside the printer so that it looked clean and tidy. To facilitate the cooling of the electronics, there are two fans working.<br />
<br />
:: The maximum printing volume is 200x200x150mm in a heated steel bed with a silicone base and on top of a borosilicate glass (prepared for the abrupt change between temperatures), so you can print with ABS without any problem (if lacquer is applied).<br />
<br />
:: The extruder is a metal E3D v5 that can heat up to 300 ° C. In this printer you can use all kinds of plastic material (ABS, PLA, etc.) available in the market. There is the option to choose the diameter of the filament that the extruder admits, so we offer it in 3 mm or 1.75 mm. The nozzle has a 0.4 mm hole in both cases.<br />
<br />
:: There is also a fan (and its support) for the radiator of the extruder whose function is to prevent the filament from clogging the conduit.<br />
<br />
:: To drive the filament, there is a cogwheel that increases the force that can be made step by step and drives a bolt with MK8 nut.<br />
<br />
:: For the Z axis (the height) it contains the Tr8x8 bars because that improves the print quality significantly.<br />
<br />
:: For the movement of the other two axes, GT2 pulleys and synchronous belts are used.<br />
<br />
:: For electronics; An Arduino MEGA 2560 is used along with a RAMPAS 1.4, which also includes 4 A4988 controllers that drive 5 NEMA17 stepper motors. Also included are 2 limit switches and a capacitive sensor for automatically autohome axes and autocalibration.<br />
<br> <br> <br><br />
:: To provide the necessary power, a power supply that emits 12 V and 5 A (60 W) is also provided, since the hot base is rated at 220V and does not consume amperage.<br />
<br />
:: The cables that are outside the base of the printer are confined in a cable chain to protect them during the movement of the axis and so that everything is tidy.<br />
<br />
:: On the back of the base there are two connectors, one to connect to the AC power switch and an integrated USB connector. It also has a space if you want to connect a Raspberry Pi (not included) to control the machine with Ocotprint over the Internet.<br />
<br />
:: Also included is a 2004 LCD that incorporates an SD card reader, to control the printer and print parts directly from the screen.<br />
<br />
=Technical Data=<br />
{| class="wikitable sortable" border="1" align="center"<br />
|-<br />
| Frame || White methacrylate 10mm Transparent methacrylate 5mm<br />
|-<br />
| Smooth rods|| 304 Steel, tolerance H9 <br />
|-<br />
| Threaded rods || Thread Tr8x8 or M8 (optional)<br />
|-<br />
| Print volume || 200x200x150 mm<br />
|-<br />
| Extruder || E3D v5 (All metal)<br />
|-<br />
| Filament diameter || 1.75/3 mm (optional) <br />
|-<br />
| Filament types || All types (PLA, ABS, Nylon, etc...)<br />
|-<br />
| Electronics || Arduino MEGA 2560 - RAMPS 1.4<br />
|-<br />
| Drivers || 4 x A4988<br />
|-<br />
| Power source || 12V/5A<br />
|-<br />
| Build platform || Steel bed with silicone base (220 V)<br />
|-<br />
| Display|| LCD 2004 with SD card reader<br />
|}<br />
<br />
==Documentation==<br />
* [http://es.docs.thingibox.com/ Assembly instructions and commissioning guide]<br />
* [https://github.com/Thingibox/ThingiBOX_Marlin Configured firmware]<br />
* [https://github.com/Thingibox/Prusa-i3-ION/tree/master/Slic3r_Configuration Configured Slic3r profile]<br />
<br />
==Features==<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION axial fans.jpg|150px|thumb|Axial fans]] ||<br />
::Unlike the original Prusa i3, our version has an opening for the electronics and the printer’s power supply. Thanks to the housing the electronic components such as control boards, power supply, cables and connectors are stowed in an orderly and safe manner.<br />
<br />
::Two small axial fans ensure the cooling of the electronics. The power supply features a built-in temperature control that cuts off electrical power in case of overheating.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Alu-Sili.jpg|150px|thumb|Heated bed]] ||<br />
:: The maximum printing volume is 200x200x190mm. The objects are printed on a 3 mm thick borosilicate glass that has a low thermal expansion. Under the glass, we place a heated steel bed that provides additional stiffness and at the same time allows to print filaments that have problems of adherence when printing at low temperature, such as ABS.<br />
<br />
::Depending on humidity conditions and room temperature, the heated bed can reach a temperature of 130ºC.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION extruder.jpg|150px|thumb|Extruder]] ||<br />
::The extruder is an E3D v5 full metal hotend that allows to print at temperatures as high as 300ºC. It is compatible with almost all available filaments. The nozzle has a 0.4mm diameter, this is a compromise between printing precision and speed.<br />
<br />
::An additional fan prevents the filament from melting before time and thus clogging the duct. The extruder incorporates standard components and can be completely disassembled; this makes cleaning and spare part replacements easier.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION MK8 drive gear wheel.jpeg|150px|thumb|MK8 drive gear wheel]] ||<br />
::The Prusa i3 ION uses a MK8 drive gear wheel to feed the filament into the extruder. The wheel is fixed on an axis with a gear on one end which increases by factor five the power that is transmitted by the motor. This way we can use a smaller motor in the extruder, reducing the motor’s inertia and increasing printing quality at the same time. This applies specially where the extruder suddenly changes its speed, for instance when printing corners.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION Z axis.jpeg|150px|thumb|Z axis]] ||<br />
:: For the Z axis (which is responsible for lifting the printer head), it contains the Tr8x8 threaded rods because they considerably improve the printing results. Traditional, uncalibrated metric bars are significantly less expensive, but can cause ripples in the printed object that are more visible in the object's workshop.<br />
<br />
:: With the Tr8x8 bars we use machined POM nuts that completely eliminate the inverted bar, typical in traditional threaded bar configurations. For even greater precision, our POM nuts are 10 mm longer than the usual nuts.<br />
<br />
:: For the movement of the other axis of the printer, it uses synchronous GT2 and belts with manual tensioners.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION electronics.jpg|150px|thumb|Arduino MEGA 2560]] ||<br />
:: Regarding electronics, this printer includes an Arduino MEGA 2560 controller together with a RAMPS 1.4 screen that incorporates 4 A4988 controllers that move 5 NEMA17 stepper motors. Also included are 2 limit switches with cable and a capacitive sensor for autohome and auto-calibration.<br />
<br />
:: The external wires of the printer are kept in a cable chain. In this way, the cables are kept in order and safe while the axis moves.<br />
<br />
<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION socket.jpeg|150px|thumb|Socket with switch]] ||<br />
::Two connectors are situated on the back side, one for the AC power supply through a socket with switch and one for USB connections in case you wish to control the printer directly from your PC.<br />
<br />
::The housing features also an opening and bores for a Raspberry Pi 2 (not included) which allows to connect the printer to the internet and control it via Octoprint.<br />
|-<br />
|}<br />
<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION LCD.jpeg|150px|thumb|LCD 2004 screen]] ||<br />
:: A 2004 LCD screen is included to monitor the printer. The screen driver includes an SD card that allows you to load designs without the need for a PC.<br />
<br />
:: There is no need to modify the firmware for the configuration of the screen. With this board you can control the printing speed without having to wait for the hotend to cool, preheat the printer, modify the firmware parameters or change the filament in the middle of the printing process; all this without a PC<br />
|-<br />
|}<br />
<br />
=Other versions=<br />
<br />
An XL version with a 200x300 printing surface is also available<br />
<br />
=Where to buy=<br />
<br />
- [http://store.thingibox.com/es/ion-v6/373-ION_v6_kit_completo.html Complete Kit in ThingiBOX] Now Available!<br />
- [http://store.thingibox.com/es/ion-v6/374-ION_v6_XL_kit_completo.html Complete Kit XL in ThingiBOX] Now Available!</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Prusa_i3_ION/es&diff=181786Prusa i3 ION/es2018-02-28T15:48:17Z<p>Merlucin: </p>
<hr />
<div>{{Languages}}<br />
<br />
{{Development<br />
<!--Header--><br />
|name = Prusa ION V6<br />
|status = working<br />
<!--Image--><br />
|image = Prusa i3 ION.PNG<br />
<!--General--><br />
|description = <br />
|reprap = Prusa i3<br />
|license = [[GPL]]<br />
|author = ThingiBOX<br />
|categories =<br />
[[:Category:Prusa i3|Prusa i3]],<br />
{{tag|Prusa i3 Development}},<br />
{{tag|Prusa Mendel Development}},<br />
{{tag|Prusa Mendel}},<br />
{{tag|Mendel Variations}},<br />
{{tag|Cartesian-XZ-head}}<br />
|CAD Models = https://github.com/Thingibox<br />
|External Link = http://store.thingibox.com/es/22-ion-v6<br />
}}<br />
<br />
<br />
=Introducción=<br />
[[Image:Prusai3 ION Front.jpg|thumb|300px|left|Prusa ION V6]]<br />
<br />
::La '' 'Prusa ION V6' '' es una impresora 3D inspirada en el Prusa i3, pero con muchos cambios, mejoras y actualizaciones. Ha sido diseñado por el equipo técnico de [http://store.thingibox.com ThingiBOX], una tienda en línea cuyos productos están relacionados con el mundo de la impresión 3D.<br />
<br />
::El objetivo del proyecto era diseñar una estructura hecha con metacrilato donde todas las partes estuvieran cortadas con una máquina láser CNC, el otro objetivo era mantener todos los componentes electrónicos dentro de la impresora para que se viera limpia y ordenada. Para facilitar el enfriamiento de la electrónica, hay instalados dos ventiladores.<br />
<br />
:: El volumen máximo de impresión es de 200x200x150mm en una cama calefactada de acero con una base de silicona y encima de un vidrio de borosilicato (preparado para el cambio abrupto entre las temperaturas), por lo que se puede imprimir con ABS sin ningún problema (si se aplica laca).<br />
<br />
<br><br><br><br><br />
<br />
::El extrusor es un v5 E3D de metal que puede calentar hasta 300 ºC. En esta impresora se pueden utilizar todo tipo de material plástico (ABS, PLA, etc.) disponible en el mercado. Existe la opción de elegir el diámetro del filamento que admite la extrusora, por lo que lo ofrecemos en 3 mm o 1,75 mm. La boquilla tiene un orificio de 0,4 mm en ambos casos.<br />
<br />
::También hay un ventilador (y su soporte) para el radiador de la extrusora cuya función es evitar que el filamento obstruya el conducto.<br />
<br />
::Para impulsar el filamento, hay una rueda dentada que aumenta la fuerza que puede hacer el paso a paso e impulsa un perno con tuerca MK8.<br />
<br />
:: Para el eje Z (la altura) contiene las barras Tr8x8 porque eso mejora la calidad de impresión significativamente.<br />
<br />
:: Para el movimiento de los otros dos ejes se utilizan poleas GT2 y correas síncronas.<br />
<br />
:: Para la electrónica; Se usa un Arduino MEGA 2560 junto con una RAMPAS 1.4, que también incluye 4 controladores A4988 que manejan 5 motores paso a paso NEMA17. También se incluyen 2 interruptores de fin de carrera y un sensor capacitivo para hacer el autohome de los ejes automáticamente y el autocalibrado.<br />
<br> <br> <br><br />
:: Para dar la potencia necesaria también se proporciona una fuente de alimentación que emite 12 V y 5 A (60 W) ya que la base caliente se contecta a 220V y no consume amperaje. <br />
<br />
::Para dar la potencia necesaria se dispone de una fuente de alimentación que proporciona 12V y 5A (60W), ya que la base de silicona funciona con 220V conectados a la entrada de la fuente, por lo que se puede utilizar una fuente de alimentación de menor amperaje.<br />
<br />
:: Los cables que están fuera de la base de la impresora están confinados en una cadena de cable para protegerlos durante el movimiento del eje y para que quede todo ordenado.<br />
<br />
:: En la parte posterior de la base hay dos conectores, uno para conectar con el interruptor de alimentación de CA y un conector USB integrado. También tiene un espacio si desea conectar una Raspberry Pi (no incluida) para controlar la máquina con Ocotprint a través de Internet.<br />
<br />
:: También se incluye una LCD 2004 que incorpora un lector de tarjetas SD, para poder controlar la impresora y imprimir piezas directamente desde la pantalla.<br />
<br />
= Datos técnicos =<br />
<br />
{| class="wikitable sortable" border="1" align="center"<br />
|-<br />
| Marco || Metacrilato blanco 8 mm metacrilato transparente 5 mm<br />
|-<br />
| Varillas lisas || Acero 304, tolerancia H9<br />
|-<br />
| Varillas roscadas || Subproceso Tr8x8 <br />
|-<br />
| Volumen de impresión || 200x200x150 mm<br />
|-<br />
| Extrusora || E3D v5 (Todo de metal)<br />
|-<br />
| Diámetro del filamento || 1.75 / 3 mm (opcional)<br />
|-<br />
| Tipos de filamentos || Todos los tipos (PLA, ABS, Nylon, etc.)<br />
|-<br />
| Electrónica || Arduino MEGA 2560 - RAMPAS 1.4<br />
|-<br />
| Controladores || 4 x A4988<br />
|-<br />
| Fuente de poder || 12V / 5A<br />
|-<br />
| Plataforma de compilación || Cama de acero con base de silicona ( 220 V)<br />
|-<br />
| Display || LCD 2004 con lector de tarjetas SD<br />
|}<br />
<br />
== Documentación ==<br />
* [http://es.docs.thingibox.com/ Manual de montaje]<br />
* [https://github.com/Thingibox/ThingiBOX_Marlin Firmware configurado]<br />
* [https://github.com/Thingibox/Prusa-i3-ION/tree/master/Slic3r_Configuration Configuración del perfil de slic3r]<br />
<br />
= Funciones =<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION axial fans.jpg|150px|thumb|Ventiladores axiales]] ||<br />
:: A diferencia del Prusa i3 original, nuestra versión tiene una abertura para la electrónica y la fuente de alimentación de la impresora. Gracias a la carcasa, los componentes electrónicos, como los paneles de control, la fuente de alimentación, los cables y los conectores, se guardan de forma ordenada y segura.<br />
<br />
:: Dos pequeños ventiladores axiales asegurarán la refrigeración de los componentes electrónicos. La fuente de alimentación cuenta con un control de temperatura incorporado que corta la energía eléctrica en caso de sobrecalentamiento.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Alu-Sili.jpg|150px|thumb|Cama caliente]] ||<br />
:: El volumen máximo de impresión es 200x200x190mm. Los objetos están impresos en un vidrio de borosilicato de 3 mm de espesor que presenta una baja expansión térmica. Debajo del vidrio, colocamos una cama calefactada de acero que proporciona rigidez adicional y al mismo tiempo permite imprimir filamentos que presentan problemas de adherencia al imprimir a baja temperatura, como el ABS.<br />
<br />
:: Dependiendo de las condiciones de humedad y la temperatura ambiente, la cama calentada puede alcanzar una temperatura de 130ºC.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION extruder.jpg|150px|thumb|Extrusora]] ||<br />
:: La extrusora es un hotend de metal completo E3D v5 que permite imprimir a temperaturas tan altas como 300ºC. Es compatible con casi todos los filamentos disponibles. La boquilla tiene un diámetro de 0.4 mm, esto es un compromiso entre la precisión de impresión y la velocidad.<br />
<br />
:: Un ventilador adicional evita que el filamento se derrita antes de tiempo y obstruya el conducto. La extrusora incorpora componentes estándar y puede desmontarse por completo; esto facilita la limpieza y los reemplazos de repuestos.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION MK8 drive gear wheel.jpeg|150px|thumb|MK8 rueda dentada]] ||<br />
:: El ION Prusa i3 usa una rueda dentada de transmisión MK8 para alimentar el filamento en la extrusora. La rueda se fija en un eje con un engranaje en un extremo que aumenta en un factor cinco la potencia que se transmite por el motor. De esta forma, podemos usar un motor más pequeño en la extrusora, reduciendo la inercia del motor y aumentando la calidad de impresión al mismo tiempo. Esto se aplica especialmente cuando la extrusora cambia repentinamente su velocidad, por ejemplo cuando se imprimen esquinas.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION Z axis.jpeg|150px|thumb|eje Z]] ||<br />
:: Para el eje Z (que es responsable de levantar el cabezal de la impresora), contiene las barras roscadas Tr8x8 porque mejoran considerablemente los resultados de impresión. Las barras métricas tradicionales, no calibradas son significativamente menos costosas, pero pueden causar ondas en el objeto impreso que son más visibles en el taller del objeto.<br />
<br />
:: Con las barras Tr8x8 empleamos tuercas POM maquinadas que eliminan completamente la barra invertida, típica en las configuraciones tradicionales de barras roscadas. Para una precisión aún mayor, nuestras tuercas POM son 10 mm más largas que las tuercas habituales.<br />
<br />
:: Para el movimiento del otro eje de la impresora utiliza GT2 síncrono y cinturones con tensores manuales.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION electronics.jpg|150px|thumb|Arduino MEGA 2560]] ||<br />
:: En cuanto a la electrónica, esta impresora incluye un controlador Arduino MEGA 2560 junto con una pantalla RAMPS 1.4 que incorpora 4 controladores A4988 que mueven 5 motores paso a paso NEMA17. También se incluyen 2 interruptores de final de carrera con cable y un sensor capacitivo para hacer el autohome y la auta calibrción.<br />
<br />
<br />
:: Los cables externos de la impresora se mantienen en una cadena de cable. De esta forma, los cables se mantienen ordenados y seguros mientras el eje se mueve.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION socket.jpeg|150px|thumb|Toma con interruptor]] ||<br />
:: Dos conectores se encuentran en la parte posterior, uno para la fuente de alimentación de CA a través de un zócalo con interruptor y uno para conexiones USB en caso de que desee controlar la impresora directamente desde su PC.<br />
<br />
:: La carcasa también cuenta con una abertura y perforaciones para una Raspberry Pi 2 (no incluida) que permite conectar la impresora a Internet y controlarla a través de Octoprint.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION LCD.jpeg|150px|thumb|Pantalla LCD 2004]] ||<br />
:: Viene incorporada una pantalla LCD 2004 para monitorear la impresora. El controlador de pantalla incluye una tarjeta SD que permite cargar diseños sin necesidad de una PC.<br />
<br />
:: No hay necesidad de modificar el firmware para la configuración de la pantalla. Con esta placa puede controlar la velocidad de impresión sin tener que esperar que el hotend se enfríe, precaliente la impresora, modifique los parámetros del firmware o cambie el filamento en el medio del proceso de impresión; todo esto sin una PC<br />
| -<br />
|}<br />
<br />
=Otras versiones=<br />
<br />
También se encuentra disponible una versión XL con una superficie de impresión de 200x300<br />
<br />
=Dónde Comprar=<br />
<br />
- [http://store.thingibox.com/es/ion-v6/373-ION_v6_kit_completo.html Kit completo de la Prusa ION V6 en ThingiBOX] Ya a la venta!</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Prusa_i3_ION/es&diff=181785Prusa i3 ION/es2018-02-28T15:44:55Z<p>Merlucin: </p>
<hr />
<div>{{Languages}}<br />
<br />
{{Development<br />
<!--Header--><br />
|name = Prusa ION V6<br />
|status = working<br />
<!--Image--><br />
|image = Prusa i3 ION.PNG<br />
<!--General--><br />
|description = <br />
|reprap = Prusa i3<br />
|license = [[GPL]]<br />
|author = ThingiBOX<br />
|categories =<br />
[[:Category:Prusa i3|Prusa i3]],<br />
{{tag|Prusa i3 Development}},<br />
{{tag|Prusa Mendel Development}},<br />
{{tag|Prusa Mendel}},<br />
{{tag|Mendel Variations}},<br />
{{tag|Cartesian-XZ-head}}<br />
}}<br />
<br />
<br />
=Introducción=<br />
[[Image:Prusai3 ION Front.jpg|thumb|300px|left|Prusa ION V6]]<br />
<br />
::La '' 'Prusa ION V6' '' es una impresora 3D inspirada en el Prusa i3, pero con muchos cambios, mejoras y actualizaciones. Ha sido diseñado por el equipo técnico de [http://store.thingibox.com ThingiBOX], una tienda en línea cuyos productos están relacionados con el mundo de la impresión 3D.<br />
<br />
::El objetivo del proyecto era diseñar una estructura hecha con metacrilato donde todas las partes estuvieran cortadas con una máquina láser CNC, el otro objetivo era mantener todos los componentes electrónicos dentro de la impresora para que se viera limpia y ordenada. Para facilitar el enfriamiento de la electrónica, hay instalados dos ventiladores.<br />
<br />
:: El volumen máximo de impresión es de 200x200x150mm en una cama calefactada de acero con una base de silicona y encima de un vidrio de borosilicato (preparado para el cambio abrupto entre las temperaturas), por lo que se puede imprimir con ABS sin ningún problema (si se aplica laca).<br />
<br />
<br><br><br><br><br />
<br />
::El extrusor es un v5 E3D de metal que puede calentar hasta 300 ºC. En esta impresora se pueden utilizar todo tipo de material plástico (ABS, PLA, etc.) disponible en el mercado. Existe la opción de elegir el diámetro del filamento que admite la extrusora, por lo que lo ofrecemos en 3 mm o 1,75 mm. La boquilla tiene un orificio de 0,4 mm en ambos casos.<br />
<br />
::También hay un ventilador (y su soporte) para el radiador de la extrusora cuya función es evitar que el filamento obstruya el conducto.<br />
<br />
::Para impulsar el filamento, hay una rueda dentada que aumenta la fuerza que puede hacer el paso a paso e impulsa un perno con tuerca MK8.<br />
<br />
:: Para el eje Z (la altura) contiene las barras Tr8x8 porque eso mejora la calidad de impresión significativamente.<br />
<br />
:: Para el movimiento de los otros dos ejes se utilizan poleas GT2 y correas síncronas.<br />
<br />
:: Para la electrónica; Se usa un Arduino MEGA 2560 junto con una RAMPAS 1.4, que también incluye 4 controladores A4988 que manejan 5 motores paso a paso NEMA17. También se incluyen 2 interruptores de fin de carrera y un sensor capacitivo para hacer el autohome de los ejes automáticamente y el autocalibrado.<br />
<br> <br> <br><br />
:: Para dar la potencia necesaria también se proporciona una fuente de alimentación que emite 12 V y 5 A (60 W) ya que la base caliente se contecta a 220V y no consume amperaje. <br />
<br />
::Para dar la potencia necesaria se dispone de una fuente de alimentación que proporciona 12V y 5A (60W), ya que la base de silicona funciona con 220V conectados a la entrada de la fuente, por lo que se puede utilizar una fuente de alimentación de menor amperaje.<br />
<br />
:: Los cables que están fuera de la base de la impresora están confinados en una cadena de cable para protegerlos durante el movimiento del eje y para que quede todo ordenado.<br />
<br />
:: En la parte posterior de la base hay dos conectores, uno para conectar con el interruptor de alimentación de CA y un conector USB integrado. También tiene un espacio si desea conectar una Raspberry Pi (no incluida) para controlar la máquina con Ocotprint a través de Internet.<br />
<br />
:: También se incluye una LCD 2004 que incorpora un lector de tarjetas SD, para poder controlar la impresora y imprimir piezas directamente desde la pantalla.<br />
<br />
= Datos técnicos =<br />
<br />
{| class="wikitable sortable" border="1" align="center"<br />
|-<br />
| Marco || Metacrilato blanco 8 mm metacrilato transparente 5 mm<br />
|-<br />
| Varillas lisas || Acero 304, tolerancia H9<br />
|-<br />
| Varillas roscadas || Subproceso Tr8x8 <br />
|-<br />
| Volumen de impresión || 200x200x150 mm<br />
|-<br />
| Extrusora || E3D v5 (Todo de metal)<br />
|-<br />
| Diámetro del filamento || 1.75 / 3 mm (opcional)<br />
|-<br />
| Tipos de filamentos || Todos los tipos (PLA, ABS, Nylon, etc.)<br />
|-<br />
| Electrónica || Arduino MEGA 2560 - RAMPAS 1.4<br />
|-<br />
| Controladores || 4 x A4988<br />
|-<br />
| Fuente de poder || 12V / 5A<br />
|-<br />
| Plataforma de compilación || Cama de acero con base de silicona ( 220 V)<br />
|-<br />
| Display || LCD 2004 con lector de tarjetas SD<br />
|}<br />
<br />
== Documentación ==<br />
* [http://es.docs.thingibox.com/ Manual de montaje]<br />
* [https://github.com/Thingibox/ThingiBOX_Marlin Firmware configurado]<br />
* [https://github.com/Thingibox/Prusa-i3-ION/tree/master/Slic3r_Configuration Configuración del perfil de slic3r]<br />
<br />
= Funciones =<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION axial fans.jpg|150px|thumb|Ventiladores axiales]] ||<br />
:: A diferencia del Prusa i3 original, nuestra versión tiene una abertura para la electrónica y la fuente de alimentación de la impresora. Gracias a la carcasa, los componentes electrónicos, como los paneles de control, la fuente de alimentación, los cables y los conectores, se guardan de forma ordenada y segura.<br />
<br />
:: Dos pequeños ventiladores axiales asegurarán la refrigeración de los componentes electrónicos. La fuente de alimentación cuenta con un control de temperatura incorporado que corta la energía eléctrica en caso de sobrecalentamiento.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Alu-Sili.jpg|150px|thumb|Cama caliente]] ||<br />
:: El volumen máximo de impresión es 200x200x190mm. Los objetos están impresos en un vidrio de borosilicato de 3 mm de espesor que presenta una baja expansión térmica. Debajo del vidrio, colocamos una cama calefactada de acero que proporciona rigidez adicional y al mismo tiempo permite imprimir filamentos que presentan problemas de adherencia al imprimir a baja temperatura, como el ABS.<br />
<br />
:: Dependiendo de las condiciones de humedad y la temperatura ambiente, la cama calentada puede alcanzar una temperatura de 130ºC.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION extruder.jpg|150px|thumb|Extrusora]] ||<br />
:: La extrusora es un hotend de metal completo E3D v5 que permite imprimir a temperaturas tan altas como 300ºC. Es compatible con casi todos los filamentos disponibles. La boquilla tiene un diámetro de 0.4 mm, esto es un compromiso entre la precisión de impresión y la velocidad.<br />
<br />
:: Un ventilador adicional evita que el filamento se derrita antes de tiempo y obstruya el conducto. La extrusora incorpora componentes estándar y puede desmontarse por completo; esto facilita la limpieza y los reemplazos de repuestos.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION MK8 drive gear wheel.jpeg|150px|thumb|MK8 rueda dentada]] ||<br />
:: El ION Prusa i3 usa una rueda dentada de transmisión MK8 para alimentar el filamento en la extrusora. La rueda se fija en un eje con un engranaje en un extremo que aumenta en un factor cinco la potencia que se transmite por el motor. De esta forma, podemos usar un motor más pequeño en la extrusora, reduciendo la inercia del motor y aumentando la calidad de impresión al mismo tiempo. Esto se aplica especialmente cuando la extrusora cambia repentinamente su velocidad, por ejemplo cuando se imprimen esquinas.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION Z axis.jpeg|150px|thumb|eje Z]] ||<br />
:: Para el eje Z (que es responsable de levantar el cabezal de la impresora), contiene las barras roscadas Tr8x8 porque mejoran considerablemente los resultados de impresión. Las barras métricas tradicionales, no calibradas son significativamente menos costosas, pero pueden causar ondas en el objeto impreso que son más visibles en el taller del objeto.<br />
<br />
:: Con las barras Tr8x8 empleamos tuercas POM maquinadas que eliminan completamente la barra invertida, típica en las configuraciones tradicionales de barras roscadas. Para una precisión aún mayor, nuestras tuercas POM son 10 mm más largas que las tuercas habituales.<br />
<br />
:: Para el movimiento del otro eje de la impresora utiliza GT2 síncrono y cinturones con tensores manuales.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION electronics.jpg|150px|thumb|Arduino MEGA 2560]] ||<br />
:: En cuanto a la electrónica, esta impresora incluye un controlador Arduino MEGA 2560 junto con una pantalla RAMPS 1.4 que incorpora 4 controladores A4988 que mueven 5 motores paso a paso NEMA17. También se incluyen 2 interruptores de final de carrera con cable y un sensor capacitivo para hacer el autohome y la auta calibrción.<br />
<br />
<br />
:: Los cables externos de la impresora se mantienen en una cadena de cable. De esta forma, los cables se mantienen ordenados y seguros mientras el eje se mueve.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION socket.jpeg|150px|thumb|Toma con interruptor]] ||<br />
:: Dos conectores se encuentran en la parte posterior, uno para la fuente de alimentación de CA a través de un zócalo con interruptor y uno para conexiones USB en caso de que desee controlar la impresora directamente desde su PC.<br />
<br />
:: La carcasa también cuenta con una abertura y perforaciones para una Raspberry Pi 2 (no incluida) que permite conectar la impresora a Internet y controlarla a través de Octoprint.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION LCD.jpeg|150px|thumb|Pantalla LCD 2004]] ||<br />
:: Viene incorporada una pantalla LCD 2004 para monitorear la impresora. El controlador de pantalla incluye una tarjeta SD que permite cargar diseños sin necesidad de una PC.<br />
<br />
:: No hay necesidad de modificar el firmware para la configuración de la pantalla. Con esta placa puede controlar la velocidad de impresión sin tener que esperar que el hotend se enfríe, precaliente la impresora, modifique los parámetros del firmware o cambie el filamento en el medio del proceso de impresión; todo esto sin una PC<br />
| -<br />
|}<br />
<br />
=Otras versiones=<br />
<br />
También se encuentra disponible una versión XL con una superficie de impresión de 200x300<br />
<br />
=Dónde Comprar=<br />
<br />
- [http://store.thingibox.com/es/ion-v6/373-ION_v6_kit_completo.html Kit completo de la Prusa ION V6 en ThingiBOX] Ya a la venta!</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=File:Alu-Sili.jpg&diff=181784File:Alu-Sili.jpg2018-02-28T15:44:12Z<p>Merlucin: </p>
<hr />
<div></div>Merlucinhttps://reprap.org/mediawiki/index.php?title=File:Prusai3_ION_heated_bed.jpg&diff=181783File:Prusai3 ION heated bed.jpg2018-02-28T15:43:51Z<p>Merlucin: Merlucin uploaded a new version of &quot;File:Prusai3 ION heated bed.jpg&quot;</p>
<hr />
<div>MK3 heated bed</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=File:Prusai3_ION_heated_bed.jpg&diff=181782File:Prusai3 ION heated bed.jpg2018-02-28T15:41:35Z<p>Merlucin: Merlucin uploaded a new version of &quot;File:Prusai3 ION heated bed.jpg&quot;: Reverted to version as of 15:40, 28 February 2018</p>
<hr />
<div>MK3 heated bed</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=File:Prusai3_ION_heated_bed.jpg&diff=181781File:Prusai3 ION heated bed.jpg2018-02-28T15:41:24Z<p>Merlucin: Merlucin uploaded a new version of &quot;File:Prusai3 ION heated bed.jpg&quot;</p>
<hr />
<div>MK3 heated bed</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=File:Prusai3_ION_heated_bed.jpg&diff=181780File:Prusai3 ION heated bed.jpg2018-02-28T15:40:22Z<p>Merlucin: Merlucin uploaded a new version of &quot;File:Prusai3 ION heated bed.jpg&quot;</p>
<hr />
<div>MK3 heated bed</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=File:Prusai3_ION_heated_bed.jpg&diff=181779File:Prusai3 ION heated bed.jpg2018-02-28T15:25:03Z<p>Merlucin: Merlucin uploaded a new version of &quot;File:Prusai3 ION heated bed.jpg&quot;</p>
<hr />
<div>MK3 heated bed</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Prusa_i3_ION/es&diff=181778Prusa i3 ION/es2018-02-28T15:01:55Z<p>Merlucin: </p>
<hr />
<div>{{Languages}}<br />
<br />
{{Development<br />
<!--Header--><br />
|name = Prusa ION V6<br />
|status = working<br />
<!--Image--><br />
|image = Prusa i3 ION.PNG<br />
<!--General--><br />
|description = <br />
|reprap = Prusa i3<br />
|license = [[GPL]]<br />
|author = ThingiBOX<br />
|categories =<br />
[[:Category:Prusa i3|Prusa i3]],<br />
{{tag|Prusa i3 Development}},<br />
{{tag|Prusa Mendel Development}},<br />
{{tag|Prusa Mendel}},<br />
{{tag|Mendel Variations}},<br />
{{tag|Cartesian-XZ-head}}<br />
}}<br />
<br />
<br />
=Introducción=<br />
[[Image:Prusai3 ION Front.jpg|thumb|300px|left|Prusa ION V6]]<br />
<br />
::La '' 'Prusa ION V6' '' es una impresora 3D inspirada en el Prusa i3, pero con muchos cambios, mejoras y actualizaciones. Ha sido diseñado por el equipo técnico de [http://store.thingibox.com ThingiBOX], una tienda en línea cuyos productos están relacionados con el mundo de la impresión 3D.<br />
<br />
::El objetivo del proyecto era diseñar una estructura hecha con metacrilato donde todas las partes estuvieran cortadas con una máquina láser CNC, el otro objetivo era mantener todos los componentes electrónicos dentro de la impresora para que se viera limpia y ordenada. Para facilitar el enfriamiento de la electrónica, hay instalados dos ventiladores.<br />
<br />
:: El volumen máximo de impresión es de 200x200x150mm en una cama calefactada de acero con una base de silicona y encima de un vidrio de borosilicato (preparado para el cambio abrupto entre las temperaturas), por lo que se puede imprimir con ABS sin ningún problema (si se aplica laca).<br />
<br />
<br><br><br><br><br />
<br />
::El extrusor es un v5 E3D de metal que puede calentar hasta 300 ºC. En esta impresora se pueden utilizar todo tipo de material plástico (ABS, PLA, etc.) disponible en el mercado. Existe la opción de elegir el diámetro del filamento que admite la extrusora, por lo que lo ofrecemos en 3 mm o 1,75 mm. La boquilla tiene un orificio de 0,4 mm en ambos casos.<br />
<br />
::También hay un ventilador (y su soporte) para el radiador de la extrusora cuya función es evitar que el filamento obstruya el conducto.<br />
<br />
::Para impulsar el filamento, hay una rueda dentada que aumenta la fuerza que puede hacer el paso a paso e impulsa un perno con tuerca MK8.<br />
<br />
:: Para el eje Z (la altura) contiene las barras Tr8x8 porque eso mejora la calidad de impresión significativamente.<br />
<br />
:: Para el movimiento de los otros dos ejes se utilizan poleas GT2 y correas síncronas.<br />
<br />
:: Para la electrónica; Se usa un Arduino MEGA 2560 junto con una RAMPAS 1.4, que también incluye 4 controladores A4988 que manejan 5 motores paso a paso NEMA17. También se incluyen 2 interruptores de fin de carrera y un sensor capacitivo para hacer el autohome de los ejes automáticamente y el autocalibrado.<br />
<br> <br> <br><br />
:: Para dar la potencia necesaria también se proporciona una fuente de alimentación que emite 12 V y 5 A (60 W) ya que la base caliente se contecta a 220V y no consume amperaje. <br />
<br />
::Para dar la potencia necesaria se dispone de una fuente de alimentación que proporciona 12V y 5A (60W), ya que la base de silicona funciona con 220V conectados a la entrada de la fuente, por lo que se puede utilizar una fuente de alimentación de menor amperaje.<br />
<br />
:: Los cables que están fuera de la base de la impresora están confinados en una cadena de cable para protegerlos durante el movimiento del eje y para que quede todo ordenado.<br />
<br />
:: En la parte posterior de la base hay dos conectores, uno para conectar con el interruptor de alimentación de CA y un conector USB integrado. También tiene un espacio si desea conectar una Raspberry Pi (no incluida) para controlar la máquina con Ocotprint a través de Internet.<br />
<br />
:: También se incluye una LCD 2004 que incorpora un lector de tarjetas SD, para poder controlar la impresora y imprimir piezas directamente desde la pantalla.<br />
<br />
= Datos técnicos =<br />
<br />
{| class="wikitable sortable" border="1" align="center"<br />
|-<br />
| Marco || Metacrilato blanco 8 mm metacrilato transparente 5 mm<br />
|-<br />
| Varillas lisas || Acero 304, tolerancia H9<br />
|-<br />
| Varillas roscadas || Subproceso Tr8x8 <br />
|-<br />
| Volumen de impresión || 200x200x150 mm<br />
|-<br />
| Extrusora || E3D v5 (Todo de metal)<br />
|-<br />
| Diámetro del filamento || 1.75 / 3 mm (opcional)<br />
|-<br />
| Tipos de filamentos || Todos los tipos (PLA, ABS, Nylon, etc.)<br />
|-<br />
| Electrónica || Arduino MEGA 2560 - RAMPAS 1.4<br />
|-<br />
| Controladores || 4 x A4988<br />
|-<br />
| Fuente de poder || 12V / 5A<br />
|-<br />
| Plataforma de compilación || Cama de acero con base de silicona ( 220 V)<br />
|-<br />
| Display || LCD 2004 con lector de tarjetas SD<br />
|}<br />
<br />
== Documentación ==<br />
* [http://es.docs.thingibox.com/ Manual de montaje]<br />
* [https://github.com/Thingibox/ThingiBOX_Marlin Firmware configurado]<br />
* [https://github.com/Thingibox/Prusa-i3-ION/tree/master/Slic3r_Configuration Configuración del perfil de slic3r]<br />
<br />
= Funciones =<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION axial fans.jpg|150px|thumb|Ventiladores axiales]] ||<br />
:: A diferencia del Prusa i3 original, nuestra versión tiene una abertura para la electrónica y la fuente de alimentación de la impresora. Gracias a la carcasa, los componentes electrónicos, como los paneles de control, la fuente de alimentación, los cables y los conectores, se guardan de forma ordenada y segura.<br />
<br />
:: Dos pequeños ventiladores axiales asegurarán la refrigeración de los componentes electrónicos. La fuente de alimentación cuenta con un control de temperatura incorporado que corta la energía eléctrica en caso de sobrecalentamiento.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION heated bed.jpg|150px|thumb|Cama caliente]] ||<br />
:: El volumen máximo de impresión es 200x200x190mm. Los objetos están impresos en un vidrio de borosilicato de 3 mm de espesor que presenta una baja expansión térmica. Debajo del vidrio, colocamos una cama calefactada de acero que proporciona rigidez adicional y al mismo tiempo permite imprimir filamentos que presentan problemas de adherencia al imprimir a baja temperatura, como el ABS.<br />
<br />
:: Dependiendo de las condiciones de humedad y la temperatura ambiente, la cama calentada puede alcanzar una temperatura de 130ºC.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION extruder.jpg|150px|thumb|Extrusora]] ||<br />
:: La extrusora es un hotend de metal completo E3D v5 que permite imprimir a temperaturas tan altas como 300ºC. Es compatible con casi todos los filamentos disponibles. La boquilla tiene un diámetro de 0.4 mm, esto es un compromiso entre la precisión de impresión y la velocidad.<br />
<br />
:: Un ventilador adicional evita que el filamento se derrita antes de tiempo y obstruya el conducto. La extrusora incorpora componentes estándar y puede desmontarse por completo; esto facilita la limpieza y los reemplazos de repuestos.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION MK8 drive gear wheel.jpeg|150px|thumb|MK8 rueda dentada]] ||<br />
:: El ION Prusa i3 usa una rueda dentada de transmisión MK8 para alimentar el filamento en la extrusora. La rueda se fija en un eje con un engranaje en un extremo que aumenta en un factor cinco la potencia que se transmite por el motor. De esta forma, podemos usar un motor más pequeño en la extrusora, reduciendo la inercia del motor y aumentando la calidad de impresión al mismo tiempo. Esto se aplica especialmente cuando la extrusora cambia repentinamente su velocidad, por ejemplo cuando se imprimen esquinas.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION Z axis.jpeg|150px|thumb|eje Z]] ||<br />
:: Para el eje Z (que es responsable de levantar el cabezal de la impresora), contiene las barras roscadas Tr8x8 porque mejoran considerablemente los resultados de impresión. Las barras métricas tradicionales, no calibradas son significativamente menos costosas, pero pueden causar ondas en el objeto impreso que son más visibles en el taller del objeto.<br />
<br />
:: Con las barras Tr8x8 empleamos tuercas POM maquinadas que eliminan completamente la barra invertida, típica en las configuraciones tradicionales de barras roscadas. Para una precisión aún mayor, nuestras tuercas POM son 10 mm más largas que las tuercas habituales.<br />
<br />
:: Para el movimiento del otro eje de la impresora utiliza GT2 síncrono y cinturones con tensores manuales.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION electronics.jpg|150px|thumb|Arduino MEGA 2560]] ||<br />
:: En cuanto a la electrónica, esta impresora incluye un controlador Arduino MEGA 2560 junto con una pantalla RAMPS 1.4 que incorpora 4 controladores A4988 que mueven 5 motores paso a paso NEMA17. También se incluyen 2 interruptores de final de carrera con cable y un sensor capacitivo para hacer el autohome y la auta calibrción.<br />
<br />
<br />
:: Los cables externos de la impresora se mantienen en una cadena de cable. De esta forma, los cables se mantienen ordenados y seguros mientras el eje se mueve.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION socket.jpeg|150px|thumb|Toma con interruptor]] ||<br />
:: Dos conectores se encuentran en la parte posterior, uno para la fuente de alimentación de CA a través de un zócalo con interruptor y uno para conexiones USB en caso de que desee controlar la impresora directamente desde su PC.<br />
<br />
:: La carcasa también cuenta con una abertura y perforaciones para una Raspberry Pi 2 (no incluida) que permite conectar la impresora a Internet y controlarla a través de Octoprint.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION LCD.jpeg|150px|thumb|Pantalla LCD 2004]] ||<br />
:: Viene incorporada una pantalla LCD 2004 para monitorear la impresora. El controlador de pantalla incluye una tarjeta SD que permite cargar diseños sin necesidad de una PC.<br />
<br />
:: No hay necesidad de modificar el firmware para la configuración de la pantalla. Con esta placa puede controlar la velocidad de impresión sin tener que esperar que el hotend se enfríe, precaliente la impresora, modifique los parámetros del firmware o cambie el filamento en el medio del proceso de impresión; todo esto sin una PC<br />
| -<br />
|}<br />
<br />
=Otras versiones=<br />
<br />
También se encuentra disponible una versión XL con una superficie de impresión de 200x300<br />
<br />
=Dónde Comprar=<br />
<br />
- [http://store.thingibox.com/es/ion-v6/373-ION_v6_kit_completo.html Kit completo de la Prusa ION V6 en ThingiBOX] Ya a la venta!</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Prusa_i3_ION/es&diff=181777Prusa i3 ION/es2018-02-28T14:59:26Z<p>Merlucin: /* Funciones */</p>
<hr />
<div>{{Languages}}<br />
<br />
{{Development<br />
<!--Header--><br />
|name = Prusa ION V6<br />
|status = working<br />
<!--Image--><br />
|image = Prusa i3 ION.PNG<br />
<!--General--><br />
|description = <br />
|reprap = Prusa i3<br />
|license = [[GPL]]<br />
|author = ThingiBOX<br />
|categories =<br />
[[:Category:Prusa i3|Prusa i3]],<br />
{{tag|Prusa i3 Development}},<br />
{{tag|Prusa Mendel Development}},<br />
{{tag|Prusa Mendel}},<br />
{{tag|Mendel Variations}},<br />
{{tag|Cartesian-XZ-head}}<br />
}}<br />
<br />
<br />
=Introducción=<br />
[[Image:Prusai3 ION Front.jpg|thumb|300px|left|Prusa ION V6]]<br />
<br />
::La '' 'Prusa ION V6' '' es una impresora 3D inspirada en el Prusa i3, pero con muchos cambios, mejoras y actualizaciones. Ha sido diseñado por el equipo técnico de [http://store.thingibox.com ThingiBOX], una tienda en línea cuyos productos están relacionados con el mundo de la impresión 3D.<br />
<br />
::El objetivo del proyecto era diseñar una estructura hecha con metacrilato donde todas las partes estuvieran cortadas con una máquina láser CNC, el otro objetivo era mantener todos los componentes electrónicos dentro de la impresora para que se viera limpia y ordenada. Para facilitar el enfriamiento de la electrónica, hay instalados dos ventiladores.<br />
<br />
:: El volumen máximo de impresión es de 200x200x150mm en una cama calefactada de acero con una base de silicona y encima de un vidrio de borosilicato (preparado para el cambio abrupto entre las temperaturas), por lo que se puede imprimir con ABS sin ningún problema (si se aplica laca).<br />
<br />
<br><br><br><br><br />
<br />
::El extrusor es un v5 E3D de metal que puede calentar hasta 300 ºC. En esta impresora se pueden utilizar todo tipo de material plástico (ABS, PLA, etc.) disponible en el mercado. Existe la opción de elegir el diámetro del filamento que admite la extrusora, por lo que lo ofrecemos en 3 mm o 1,75 mm. La boquilla tiene un orificio de 0,4 mm en ambos casos.<br />
<br />
::También hay un ventilador (y su soporte) para el radiador de la extrusora cuya función es evitar que el filamento obstruya el conducto.<br />
<br />
::Para impulsar el filamento, hay una rueda dentada que aumenta la fuerza que puede hacer el paso a paso e impulsa un perno con tuerca MK8.<br />
<br />
:: Para el eje Z (la altura) contiene las barras Tr8x8 porque eso mejora la calidad de impresión significativamente.<br />
<br />
:: Para el movimiento de los otros dos ejes se utilizan poleas GT2 y correas síncronas.<br />
<br />
:: Para la electrónica; Se usa un Arduino MEGA 2560 junto con una RAMPAS 1.4, que también incluye 4 controladores A4988 que manejan 5 motores paso a paso NEMA17. También se incluyen 2 interruptores de fin de carrera y un sensor capacitivo para hacer el autohome de los ejes automáticamente y el autocalibrado.<br />
<br> <br> <br><br />
:: Para dar la potencia necesaria también se proporciona una fuente de alimentación que emite 12 V y 5 A (60 W) ya que la base caliente se contecta a 220V y no consume amperaje. <br />
<br />
::Para dar la potencia necesaria se dispone de una fuente de alimentación que proporciona 12V y 5A (60W), ya que la base de silicona funciona con 220V conectados a la entrada de la fuente, por lo que se puede utilizar una fuente de alimentación de menor amperaje.<br />
<br />
:: Los cables que están fuera de la base de la impresora están confinados en una cadena de cable para protegerlos durante el movimiento del eje y para que quede todo ordenado.<br />
<br />
:: En la parte posterior de la base hay dos conectores, uno para conectar con el interruptor de alimentación de CA y un conector USB integrado. También tiene un espacio si desea conectar una Raspberry Pi (no incluida) para controlar la máquina con Ocotprint a través de Internet.<br />
<br />
:: También se incluye una LCD 2004 que incorpora un lector de tarjetas SD, para poder controlar la impresora y imprimir piezas directamente desde la pantalla.<br />
<br />
= Datos técnicos =<br />
<br />
{| class="wikitable sortable" border="1" align="center"<br />
|-<br />
| Marco || Metacrilato blanco 8 mm metacrilato transparente 5 mm<br />
| -<br />
| Varillas lisas || Acero 304, tolerancia H9<br />
| -<br />
| Varillas roscadas || Subproceso Tr8x8 <br />
| -<br />
| Volumen de impresión || 200x200x150 mm<br />
| -<br />
| Extrusora || E3D v5 (Todo de metal)<br />
| -<br />
| Diámetro del filamento || 1.75 / 3 mm (opcional)<br />
| -<br />
| Tipos de filamentos || Todos los tipos (PLA, ABS, Nylon, etc.)<br />
| -<br />
| Electrónica || Arduino MEGA 2560 - RAMPAS 1.4<br />
| -<br />
| Controladores || 4 x A4988<br />
| -<br />
| Fuente de poder || 12V / 5A<br />
| -<br />
| Plataforma de compilación || Cama de acero con base de silicona ( 220 V)<br />
| -<br />
| Display || LCD 2004 con lector de tarjetas SD<br />
|}<br />
<br />
== Documentación ==<br />
* [http://es.docs.thingibox.com/ Manual de montaje]<br />
* [https://github.com/Thingibox/ThingiBOX_Marlin Firmware configurado]<br />
* [https://github.com/Thingibox/Prusa-i3-ION/tree/master/Slic3r_Configuration Configuración del perfil de slic3r]<br />
<br />
== Funciones ==<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION axial fans.jpg|150px|thumb|Ventiladores axiales]] ||<br />
:: A diferencia del Prusa i3 original, nuestra versión tiene una abertura para la electrónica y la fuente de alimentación de la impresora. Gracias a la carcasa, los componentes electrónicos, como los paneles de control, la fuente de alimentación, los cables y los conectores, se guardan de forma ordenada y segura.<br />
<br />
:: Dos pequeños ventiladores axiales asegurarán la refrigeración de los componentes electrónicos. La fuente de alimentación cuenta con un control de temperatura incorporado que corta la energía eléctrica en caso de sobrecalentamiento.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION heated bed.jpg|150px|thumb|Cama caliente]] ||<br />
:: El volumen máximo de impresión es 200x200x190mm. Los objetos están impresos en un vidrio de borosilicato de 3 mm de espesor que presenta una baja expansión térmica. Debajo del vidrio, colocamos una cama calefactada de acero que proporciona rigidez adicional y al mismo tiempo permite imprimir filamentos que presentan problemas de adherencia al imprimir a baja temperatura, como el ABS.<br />
<br />
:: Dependiendo de las condiciones de humedad y la temperatura ambiente, la cama calentada puede alcanzar una temperatura de 130ºC.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION extruder.jpg|150px|thumb|Extrusora]] ||<br />
:: La extrusora es un hotend de metal completo E3D v5 que permite imprimir a temperaturas tan altas como 300ºC. Es compatible con casi todos los filamentos disponibles. La boquilla tiene un diámetro de 0.4 mm, esto es un compromiso entre la precisión de impresión y la velocidad.<br />
<br />
:: Un ventilador adicional evita que el filamento se derrita antes de tiempo y obstruya el conducto. La extrusora incorpora componentes estándar y puede desmontarse por completo; esto facilita la limpieza y los reemplazos de repuestos.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION MK8 drive gear wheel.jpeg|150px|thumb|MK8 rueda dentada]] ||<br />
:: El ION Prusa i3 usa una rueda dentada de transmisión MK8 para alimentar el filamento en la extrusora. La rueda se fija en un eje con un engranaje en un extremo que aumenta en un factor cinco la potencia que se transmite por el motor. De esta forma, podemos usar un motor más pequeño en la extrusora, reduciendo la inercia del motor y aumentando la calidad de impresión al mismo tiempo. Esto se aplica especialmente cuando la extrusora cambia repentinamente su velocidad, por ejemplo cuando se imprimen esquinas.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION Z axis.jpeg|150px|thumb|eje Z]] ||<br />
:: Para el eje Z (que es responsable de levantar el cabezal de la impresora), contiene las barras roscadas Tr8x8 porque mejoran considerablemente los resultados de impresión. Las barras métricas tradicionales, no calibradas son significativamente menos costosas, pero pueden causar ondas en el objeto impreso que son más visibles en el taller del objeto.<br />
<br />
:: Con las barras Tr8x8 empleamos tuercas POM maquinadas que eliminan completamente la barra invertida, típica en las configuraciones tradicionales de barras roscadas. Para una precisión aún mayor, nuestras tuercas POM son 10 mm más largas que las tuercas habituales.<br />
<br />
:: Para el movimiento del otro eje de la impresora utiliza GT2 síncrono y cinturones con tensores manuales.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION electronics.jpg|150px|thumb|Arduino MEGA 2560]] ||<br />
:: En cuanto a la electrónica, esta impresora incluye un controlador Arduino MEGA 2560 junto con una pantalla RAMPS 1.4 que incorpora 4 controladores A4988 que mueven 5 motores paso a paso NEMA17. También se incluyen 2 interruptores de final de carrera con cable y un sensor capacitivo para hacer el autohome y la auta calibrción.<br />
<br />
<br />
:: Los cables externos de la impresora se mantienen en una cadena de cable. De esta forma, los cables se mantienen ordenados y seguros mientras el eje se mueve.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION socket.jpeg|150px|thumb|Toma con interruptor]] ||<br />
:: Dos conectores se encuentran en la parte posterior, uno para la fuente de alimentación de CA a través de un zócalo con interruptor y uno para conexiones USB en caso de que desee controlar la impresora directamente desde su PC.<br />
<br />
:: La carcasa también cuenta con una abertura y perforaciones para una Raspberry Pi 2 (no incluida) que permite conectar la impresora a Internet y controlarla a través de Octoprint.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION LCD.jpeg|150px|thumb|Pantalla LCD 2004]] ||<br />
:: Viene incorporada una pantalla LCD 2004 para monitorear la impresora. El controlador de pantalla incluye una tarjeta SD que permite cargar diseños sin necesidad de una PC.<br />
<br />
:: No hay necesidad de modificar el firmware para la configuración de la pantalla. Con esta placa puede controlar la velocidad de impresión sin tener que esperar que el hotend se enfríe, precaliente la impresora, modifique los parámetros del firmware o cambie el filamento en el medio del proceso de impresión; todo esto sin una PC<br />
| -<br />
|}<br />
<br />
==Otras versiones==<br />
<br />
También se encuentra disponible una versión XL con una superficie de impresión de 200x300<br />
<br />
=Dónde Comprar=<br />
<br />
- [http://store.thingibox.com/es/ion-v6/373-ION_v6_kit_completo.html Kit completo de la Prusa ION V6 en ThingiBOX] Ya a la venta!</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Prusa_i3_ION/es&diff=181776Prusa i3 ION/es2018-02-28T14:53:55Z<p>Merlucin: </p>
<hr />
<div>{{Languages}}<br />
<br />
{{Development<br />
<!--Header--><br />
|name = Prusa ION V6<br />
|status = working<br />
<!--Image--><br />
|image = Prusa i3 ION.PNG<br />
<!--General--><br />
|description = <br />
|reprap = Prusa i3<br />
|license = [[GPL]]<br />
|author = ThingiBOX<br />
|categories =<br />
[[:Category:Prusa i3|Prusa i3]],<br />
{{tag|Prusa i3 Development}},<br />
{{tag|Prusa Mendel Development}},<br />
{{tag|Prusa Mendel}},<br />
{{tag|Mendel Variations}},<br />
{{tag|Cartesian-XZ-head}}<br />
}}<br />
<br />
<br />
=Introducción=<br />
[[Image:Prusai3 ION Front.jpg|thumb|300px|left|Prusa ION V6]]<br />
<br />
::La '' 'Prusa ION V6' '' es una impresora 3D inspirada en el Prusa i3, pero con muchos cambios, mejoras y actualizaciones. Ha sido diseñado por el equipo técnico de [http://store.thingibox.com ThingiBOX], una tienda en línea cuyos productos están relacionados con el mundo de la impresión 3D.<br />
<br />
::El objetivo del proyecto era diseñar una estructura hecha con metacrilato donde todas las partes estuvieran cortadas con una máquina láser CNC, el otro objetivo era mantener todos los componentes electrónicos dentro de la impresora para que se viera limpia y ordenada. Para facilitar el enfriamiento de la electrónica, hay instalados dos ventiladores.<br />
<br />
:: El volumen máximo de impresión es de 200x200x150mm en una cama calefactada de acero con una base de silicona y encima de un vidrio de borosilicato (preparado para el cambio abrupto entre las temperaturas), por lo que se puede imprimir con ABS sin ningún problema (si se aplica laca).<br />
<br />
<br><br><br><br><br />
<br />
::El extrusor es un v5 E3D de metal que puede calentar hasta 300 ºC. En esta impresora se pueden utilizar todo tipo de material plástico (ABS, PLA, etc.) disponible en el mercado. Existe la opción de elegir el diámetro del filamento que admite la extrusora, por lo que lo ofrecemos en 3 mm o 1,75 mm. La boquilla tiene un orificio de 0,4 mm en ambos casos.<br />
<br />
::También hay un ventilador (y su soporte) para el radiador de la extrusora cuya función es evitar que el filamento obstruya el conducto.<br />
<br />
::Para impulsar el filamento, hay una rueda dentada que aumenta la fuerza que puede hacer el paso a paso e impulsa un perno con tuerca MK8.<br />
<br />
:: Para el eje Z (la altura) contiene las barras Tr8x8 porque eso mejora la calidad de impresión significativamente.<br />
<br />
:: Para el movimiento de los otros dos ejes se utilizan poleas GT2 y correas síncronas.<br />
<br />
:: Para la electrónica; Se usa un Arduino MEGA 2560 junto con una RAMPAS 1.4, que también incluye 4 controladores A4988 que manejan 5 motores paso a paso NEMA17. También se incluyen 2 interruptores de fin de carrera y un sensor capacitivo para hacer el autohome de los ejes automáticamente y el autocalibrado.<br />
<br> <br> <br><br />
:: Para dar la potencia necesaria también se proporciona una fuente de alimentación que emite 12 V y 5 A (60 W) ya que la base caliente se contecta a 220V y no consume amperaje. <br />
<br />
::Para dar la potencia necesaria se dispone de una fuente de alimentación que proporciona 12V y 5A (60W), ya que la base de silicona funciona con 220V conectados a la entrada de la fuente, por lo que se puede utilizar una fuente de alimentación de menor amperaje.<br />
<br />
:: Los cables que están fuera de la base de la impresora están confinados en una cadena de cable para protegerlos durante el movimiento del eje y para que quede todo ordenado.<br />
<br />
:: En la parte posterior de la base hay dos conectores, uno para conectar con el interruptor de alimentación de CA y un conector USB integrado. También tiene un espacio si desea conectar una Raspberry Pi (no incluida) para controlar la máquina con Ocotprint a través de Internet.<br />
<br />
:: También se incluye una LCD 2004 que incorpora un lector de tarjetas SD, para poder controlar la impresora y imprimir piezas directamente desde la pantalla.<br />
<br />
= Datos técnicos =<br />
<br />
{| class="wikitable sortable" border="1" align="center"<br />
|-<br />
| Marco || Metacrilato blanco 8 mm metacrilato transparente 5 mm<br />
| -<br />
| Varillas lisas || Acero 304, tolerancia H9<br />
| -<br />
| Varillas roscadas || Subproceso Tr8x8 <br />
| -<br />
| Volumen de impresión || 200x200x150 mm<br />
| -<br />
| Extrusora || E3D v5 (Todo de metal)<br />
| -<br />
| Diámetro del filamento || 1.75 / 3 mm (opcional)<br />
| -<br />
| Tipos de filamentos || Todos los tipos (PLA, ABS, Nylon, etc.)<br />
| -<br />
| Electrónica || Arduino MEGA 2560 - RAMPAS 1.4<br />
| -<br />
| Controladores || 4 x A4988<br />
| -<br />
| Fuente de poder || 12V / 5A<br />
| -<br />
| Plataforma de compilación || Cama de acero con base de silicona ( 220 V)<br />
| -<br />
| Display || LCD 2004 con lector de tarjetas SD<br />
|}<br />
<br />
== Documentación ==<br />
* [http://es.docs.thingibox.com/ Manual de montaje]<br />
* [https://github.com/Thingibox/ThingiBOX_Marlin Firmware configurado]<br />
* [https://github.com/Thingibox/Prusa-i3-ION/tree/master/Slic3r_Configuration Configuración del perfil de slic3r]<br />
<br />
== Funciones ==<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION axial fans.jpg|150px|thumb|Ventiladores axiales]] ||<br />
:: A diferencia del Prusa i3 original, nuestra versión tiene una abertura para la electrónica y la fuente de alimentación de la impresora. Gracias a la carcasa, los componentes electrónicos, como los paneles de control, la fuente de alimentación, los cables y los conectores, se guardan de forma ordenada y segura.<br />
<br />
:: Dos pequeños ventiladores axiales asegurarán la refrigeración de los componentes electrónicos. La fuente de alimentación cuenta con un control de temperatura incorporado que corta la energía eléctrica en caso de sobrecalentamiento.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION heated bed.jpg|150px|thumb|Cama caliente]] ||<br />
:: El volumen máximo de impresión es 200x200x190mm. Los objetos están impresos en un vidrio de borosilicato de 3 mm de espesor que presenta una baja expansión térmica. Debajo del vidrio, colocamos una cama calefactada de acero que proporciona rigidez adicional y al mismo tiempo permite imprimir filamentos que presentan problemas de adherencia al imprimir a baja temperatura, como el ABS.<br />
<br />
:: Dependiendo de las condiciones de humedad y la temperatura ambiente, la cama calentada puede alcanzar una temperatura de 130ºC.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION extruder.jpg|150px|thumb|Extrusora]] ||<br />
:: La extrusora es un hotend de metal completo E3D v5 que permite imprimir a temperaturas tan altas como 300ºC. Es compatible con casi todos los filamentos disponibles. La boquilla tiene un diámetro de 0.4 mm, esto es un compromiso entre la precisión de impresión y la velocidad.<br />
<br />
:: Un ventilador adicional evita que el filamento se derrita antes de tiempo y obstruya el conducto. La extrusora incorpora componentes estándar y puede desmontarse por completo; esto facilita la limpieza y los reemplazos de repuestos.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION MK8 drive gear wheel.jpeg|150px|thumb|MK8 rueda dentada]] ||<br />
:: El ION Prusa i3 usa una rueda dentada de transmisión MK8 para alimentar el filamento en la extrusora. La rueda se fija en un eje con un engranaje en un extremo que aumenta en un factor cinco la potencia que se transmite por el motor. De esta forma, podemos usar un motor más pequeño en la extrusora, reduciendo la inercia del motor y aumentando la calidad de impresión al mismo tiempo. Esto se aplica especialmente cuando la extrusora cambia repentinamente su velocidad, por ejemplo cuando se imprimen esquinas.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION Z axis.jpeg|150px|thumb|eje Z]] ||<br />
:: Para el eje Z (que es responsable de levantar el cabezal de la impresora), contiene las barras roscadas Tr8x8 porque mejoran considerablemente los resultados de impresión. Las barras métricas tradicionales, no calibradas son significativamente menos costosas, pero pueden causar ondas en el objeto impreso que son más visibles en el taller del objeto.<br />
<br />
:: Con las barras Tr8x8 empleamos tuercas POM maquinadas que eliminan completamente la barra invertida, típica en las configuraciones tradicionales de barras roscadas. Para una precisión aún mayor, nuestras tuercas POM son 10 mm más largas que las tuercas habituales.<br />
<br />
:: Para el movimiento del otro eje de la impresora utiliza GT2 síncrono y cinturones con tensores manuales.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION electronics.jpg|150px|thumb|Arduino MEGA 2560]] ||<br />
:: En cuanto a la electrónica, esta impresora incluye un controlador Arduino MEGA 2560 junto con una pantalla RAMPS 1.4 que incorpora 4 controladores A4988 que mueven 5 motores paso a paso NEMA17. También se incluyen 2 interruptores de final de carrera con cable y un sensor capacitivo para hacer el autohome y la auta calibrción.<br />
<br />
<br />
:: Los cables externos de la impresora se mantienen en una cadena de cable. De esta forma, los cables se mantienen ordenados y seguros mientras el eje se mueve.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION socket.jpeg|150px|thumb|Toma con interruptor]] ||<br />
:: Dos conectores se encuentran en la parte posterior, uno para la fuente de alimentación de CA a través de un zócalo con interruptor y uno para conexiones USB en caso de que desee controlar la impresora directamente desde su PC.<br />
<br />
:: La carcasa también cuenta con una abertura y perforaciones para una Raspberry Pi 2 (no incluida) que permite conectar la impresora a Internet y controlarla a través de Octoprint.<br />
| -<br />
|}<br />
<br />
{|<br />
| -<br />
| [[File:Prusai3 ION LCD.jpeg|150px|thumb|Pantalla LCD 2004]] ||<br />
:: Viene incorporada una pantalla LCD 2004 para monitorear la impresora. El controlador de pantalla incluye una tarjeta SD que permite cargar diseños sin necesidad de una PC.<br />
<br />
:: No hay necesidad de modificar el firmware para la configuración de la pantalla. Con esta placa puede controlar la velocidad de impresión sin tener que esperar que el hotend se enfríe, precaliente la impresora, modifique los parámetros del firmware o cambie el filamento en el medio del proceso de impresión; todo esto sin una PC<br />
| -<br />
|}<br />
<br />
=Otras versiones=<br />
<br />
También se encuentra disponible una versión XL con una superficie de impresión de 200x300<br />
<br />
=Dónde Comprar=<br />
<br />
- [http://store.thingibox.com/es/ion-v6/373-ION_v6_kit_completo.html Kit completo de la Prusa ION V6 en ThingiBOX] Ya a la venta!</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Prusa_i3_ION/es&diff=181775Prusa i3 ION/es2018-02-28T11:53:04Z<p>Merlucin: </p>
<hr />
<div>{{Languages}}<br />
<br />
{{Development<br />
<!--Header--><br />
|name = Prusa ION V6<br />
|status = working<br />
<!--Image--><br />
|image = Prusa i3 ION.PNG<br />
<!--General--><br />
|description = <br />
|reprap = Prusa i3<br />
|license = [[GPL]]<br />
|author = ThingiBOX<br />
|categories =<br />
[[:Category:Prusa i3|Prusa i3]],<br />
{{tag|Prusa i3 Development}},<br />
{{tag|Prusa Mendel Development}},<br />
{{tag|Prusa Mendel}},<br />
{{tag|Mendel Variations}},<br />
{{tag|Cartesian-XZ-head}}<br />
}}<br />
<br />
<br />
=Introducción=<br />
[[Image:Prusai3 ION Front.jpg|thumb|300px|left|Prusa i3 ION]]<br />
<br />
::La Prusa ION V6 es una impresora 3D inspirada en la Prusa i3, pero con muchas cambios, mejoras y actualizaciones. Ha sido diseñada por el equipo técnico de ThingiBOX, una tienda virtual cuyos productos están relacionados con el mundo de la impresión 3D.<br />
<br />
::El proyecto tenía como objetivo diseñar una estructura de metacrilato que aunara todo los elementos necesarios para su funcionamiento, a diferencia de las reprap tradicionales donde la electrónica de control y la fuente de alimentación iba separada de la estructura. Además, el metacrilato transparente ayuda a que el diseño sea más limpio y atractivo.<br />
<br />
::En esta impresora el marco, la estructura y la mayoría de los componentes están hechos con metacrilato blanco y metacrilato transparente respectivamente que hace que el diseño sea elegante, limpio y robusto a la vez. Todas estas piezas están diseñadas por nosotros y las cortamos con una CNC láser de alta precisión, así que disponemos de repuestos.<br />
<br><br><br><br><br />
<br />
::Una característica que la hace distinta a la Prusa i3 normal es la caja que alberga la electrónica que hace a su vez de base de la impresora. En esa caja los elementos electrónicos como las placas de control, la fuente de alimentación, cables y conectores quedan recogidos de manera ordenada y dentro del perímetro de la impresora aprovechando el espacio. Para facilitar la refrigeración de la electrónica hay unos ventiladores que se encargan.<br />
<br />
::El volumen máximo de impresión de las piezas es de 200x200x150mm sobre una base de acero, con una base de silicona y encima un cristal de borosilicato (preparado para el cambio brusco entre temperaturas), así que se puede imprimir con ABS sin ningún problema (si además se pone laca fijadora).<br />
<br />
::El extrusor es un E3D v5 hecho todo de metal ya que así puede calentar hasta a una temperatura de 300ºC. Todos los filamentos de material plástico (ABS, PLA, etc...) disponibles en el mercado pueden utilizarse en esta impresora. Existe la opción de escoger el diámetro del filamento que el extrusor admite, ya que lo ofrecemos en 3mm o en 1,75mm. El nozzle o boquilla tiene un orificio de 0,4mm en ambos casos.<br />
::Se incluye un ventilador (y su soporte) para el radiador del extrusor cuya función es evitar que el filamento funda antes de lo previsto y se obstruya el conducto.<br />
<br />
::Para empujar el filamento al extrusor se usa una rueda dentada MK8 fijada a un eje en cuyo extremo hay un engranaje que magnifica la fuerza que el motor le transmite.<br />
<br />
::Para el Eje Z (el de la altura) se dispone de barras Tr8x8 ya que permiten mejorar la calidad de la impresión de manera notable.<br />
::Para el movimiento de los otros dos ejes se utilizan poleas y correas síncronas GT2.<br />
<br />
::En cuanto a la electrónica se usa una placa Arduino MEGA 2560 junto con una RAMPS 1.4, incluyendo 4 drivers A4988 que mueven 5 motores paso a paso NEMA17. También se incluyen 2 finales de carrera con cable y un sensor capacitivo para que se pueda hacer “homing” de manera automática y un auto calibrado de precisión sobre cualquier superficie de impresión.<br />
<br />
::Para dar la potencia necesaria se dispone de una fuente de alimentación que proporciona 12V y 5A (60W), ya que la base de silicona funciona con 220V conectados a la entrada de la fuente, por lo que se puede utilizar una fuente de alimentación de menor amperaje.<br />
<br />
::Los cables que están fuera de la base de la impresora están confinados dentro de una cadena portacables ayudando así a que estéticamente se vea todo ordenado y además los cables queden protegidos durante el movimiento de los ejes.<br />
<br />
::En la parte trasera se empotran dos conectores, uno para conectar la alimentación con la red AC con interruptor y otro con toma USB. Además dispone de un espacio por si se quiere conectar una Raspberry Pi (no incluida) para controlar la máquina con Ocotprint a través de internet.<br />
<br />
::Viene incluida una LCD 2004 que lleva incorporado un lector de tarjetas SD con la que se puede leer y imprimir los archivos gcode de las piezas. Además permite hacer lo mismo que desde un ordenador como por ejemplo mover ejes por separado o cambiar configuraciones desde un botón rotatorio.<br />
<br />
=Dónde Comprar=<br />
<br />
- [http://store.thingibox.com/es/ion-v6/373-ION_v6_kit_completo.html Kit completo de la Prusa ION V6 en ThingiBOX] Ya a la venta!</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Prusa_i3_Variants&diff=181645Prusa i3 Variants2018-02-01T10:11:04Z<p>Merlucin: /* Placeholder for now */</p>
<hr />
<div>== Introduction==<br />
<br />
The Prusa i3 is a Cartesian style Open Source RepRap 3D printer designed by Josef Prusa. The design of the Prusa i3 did not emerge out of the vacuum, it is actually - as its name indicates - the third iteration of a basic design by Josef Prusa, and as such it was preceded by the Prusa i2.<br />
<br />
However, this page is not concerned with what preceded the Prusa i3, but rather with what followed it!<br />
<br />
The design of the Prusa i3 can be described by various subjective qualities (e.g. "clean", "simple", "good-looking", etc) but it is due to some very objective factors that the Prusa i3 has spawned a large number of variants worldwide:<br />
* The Prusa i3 design is licensed under the GPL.<br />
* The Prusa i3 design and assembly process are properly documented.<br />
* The Prusa i3 is a low cost design.<br />
<br />
The Prusa i3 variants use various different materials for the frame, and have specific design objectives in relation to the original Prusa i3. These various objectives can be one or a combination of:<br />
* a reduction in cost.<br />
* a reduction in the total number of parts.<br />
* a reduction in the number of printed parts, or their replacement altogether with parts resulting from a different production process (e.g. laser-cutting).<br />
* a reduction in the time required for assembly or adjustments.<br />
* increased rigidity of the frame.<br />
* increased robustness of the parts.<br />
* changes in the "looks" for simple aesthetic reasons.<br />
* other possible optimizations.<br />
<br />
== Graber i3 Laser Cut ==<br />
<br />
<br />
[[File:Prusa-i3-wood.jpg|thumb|none|alt=Wood style sheet frame|Wood style sheet frame]]<br />
[[File:Prusa-i3-wood-in-melamime.jpg|thumb|right|alt=Wood style sheet frame, made out of melamine-resin particle board|Wood style sheet frame, made out of melamine-resin particle board]]<br />
<br />
This is a version of the sheet frame that is designed to be laser cut out of wood or plastic (e.g., acrylic) if you don't have access to a water&ndash;jet cutter. The only difference is that this version has support gussets on the back side of the vertical frame (the side that doesn't have the Z&ndash;threaded rods); construction is the same.<br />
<br />
A [http://github.com/sgraber/Prusa3_LC github repository] with laser cutting files has been created by S. Graber.<br />
<br />
'''Pro:'''<br />
<br />
* Looks professional (subjective).<br />
<br />
'''Con:'''<br />
<br />
* Requires specialized tools (e.g., laser cutter).<br />
* Less rigid connection between XZ&ndash;frame and Y&ndash;frame part (connects in the same way as the aluminium sheet frame).<br />
<br />
<br />
== Placeholder for now ==<br />
<br />
There are numerous Prusa i3 variants published on GitHub and Thingiverse:<br />
<br />
* ''Prusa i3 Improved for laser cut by Twelvepro.com'' - [http://www.thingiverse.com/thing:39889] (also see [http://twelvepro.com/news/category/prusa-i3-by-twelvepro/ these pictures of an assembled Prusa i3 Twelvepro] )<br />
<br />
* ''P3Steel by irobri'', a Prusa i3 Twelvepro remix using laser-cut 3mm steel - ([[P3Steel]])<br />
<br />
* ''Prusa i3 aluminum frame w/ aluminum upgrades'' by Nathaniel E. Bolin - [http://www.thingiverse.com/thing:68296]<br />
<br />
* ''Prusa I3 using aluminum profile'' by ju jusujn - [http://www.thingiverse.com/thing:322025]<br />
<br />
* ''Graber i3 Laser Cut'' by S. Graber: complete laser cut design (no printed parts) - http://twelvepro.com/index.php?route=product/product&product_id=52 Assembly pictures are here - http://twelvepro.com/news/graber-i3-assembly/<br />
<br />
* ''Prusa i3 Rework''<br />
<br />
* ''Prusa i3 PowerCode''<br />
<br />
* ''Prusa i3 EiNSTeIN''<br />
<br />
* ''Ṕrusa i3 Hephestos''<br />
<br />
* [[Prusa i3d]]<br />
<br />
* ''Wilson TS''<br />
<br />
*[http://reprap.org/wiki/Prusa_i3_ION Prusa ION V6] [http://store.thingibox.com/es/ion-v6/373-ION_v6_kit_completo.html by Thingibox ] with assembly manual<br />
<br />
== Evolution timeline==<br />
<br />
== Table of Prusa i3 variants==<br />
<br />
== Notes==<br />
<br />
[[Category:Prusa i3 Development]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Prusa_i3_Variants&diff=181644Prusa i3 Variants2018-01-31T10:56:28Z<p>Merlucin: /* Placeholder for now */</p>
<hr />
<div>== Introduction==<br />
<br />
The Prusa i3 is a Cartesian style Open Source RepRap 3D printer designed by Josef Prusa. The design of the Prusa i3 did not emerge out of the vacuum, it is actually - as its name indicates - the third iteration of a basic design by Josef Prusa, and as such it was preceded by the Prusa i2.<br />
<br />
However, this page is not concerned with what preceded the Prusa i3, but rather with what followed it!<br />
<br />
The design of the Prusa i3 can be described by various subjective qualities (e.g. "clean", "simple", "good-looking", etc) but it is due to some very objective factors that the Prusa i3 has spawned a large number of variants worldwide:<br />
* The Prusa i3 design is licensed under the GPL.<br />
* The Prusa i3 design and assembly process are properly documented.<br />
* The Prusa i3 is a low cost design.<br />
<br />
The Prusa i3 variants use various different materials for the frame, and have specific design objectives in relation to the original Prusa i3. These various objectives can be one or a combination of:<br />
* a reduction in cost.<br />
* a reduction in the total number of parts.<br />
* a reduction in the number of printed parts, or their replacement altogether with parts resulting from a different production process (e.g. laser-cutting).<br />
* a reduction in the time required for assembly or adjustments.<br />
* increased rigidity of the frame.<br />
* increased robustness of the parts.<br />
* changes in the "looks" for simple aesthetic reasons.<br />
* other possible optimizations.<br />
<br />
== Graber i3 Laser Cut ==<br />
<br />
<br />
[[File:Prusa-i3-wood.jpg|thumb|none|alt=Wood style sheet frame|Wood style sheet frame]]<br />
[[File:Prusa-i3-wood-in-melamime.jpg|thumb|right|alt=Wood style sheet frame, made out of melamine-resin particle board|Wood style sheet frame, made out of melamine-resin particle board]]<br />
<br />
This is a version of the sheet frame that is designed to be laser cut out of wood or plastic (e.g., acrylic) if you don't have access to a water&ndash;jet cutter. The only difference is that this version has support gussets on the back side of the vertical frame (the side that doesn't have the Z&ndash;threaded rods); construction is the same.<br />
<br />
A [http://github.com/sgraber/Prusa3_LC github repository] with laser cutting files has been created by S. Graber.<br />
<br />
'''Pro:'''<br />
<br />
* Looks professional (subjective).<br />
<br />
'''Con:'''<br />
<br />
* Requires specialized tools (e.g., laser cutter).<br />
* Less rigid connection between XZ&ndash;frame and Y&ndash;frame part (connects in the same way as the aluminium sheet frame).<br />
<br />
<br />
== Placeholder for now ==<br />
<br />
There are numerous Prusa i3 variants published on GitHub and Thingiverse:<br />
<br />
* ''Prusa i3 Improved for laser cut by Twelvepro.com'' - [http://www.thingiverse.com/thing:39889] (also see [http://twelvepro.com/news/category/prusa-i3-by-twelvepro/ these pictures of an assembled Prusa i3 Twelvepro] )<br />
<br />
* ''P3Steel by irobri'', a Prusa i3 Twelvepro remix using laser-cut 3mm steel - ([[P3Steel]])<br />
<br />
* ''Prusa i3 aluminum frame w/ aluminum upgrades'' by Nathaniel E. Bolin - [http://www.thingiverse.com/thing:68296]<br />
<br />
* ''Prusa I3 using aluminum profile'' by ju jusujn - [http://www.thingiverse.com/thing:322025]<br />
<br />
* ''Graber i3 Laser Cut'' by S. Graber: complete laser cut design (no printed parts) - http://twelvepro.com/index.php?route=product/product&product_id=52 Assembly pictures are here - http://twelvepro.com/news/graber-i3-assembly/<br />
<br />
* ''Prusa i3 Rework''<br />
<br />
* ''Prusa i3 PowerCode''<br />
<br />
* ''Prusa i3 EiNSTeIN''<br />
<br />
* ''Ṕrusa i3 Hephestos''<br />
<br />
* [[Prusa i3d]]<br />
<br />
* ''Wilson TS''<br />
<br />
*"Prusa ION V6" [http://store.thingibox.com/es/ion-v6/373-ION_v6_kit_completo.html by Thingibox with assembly manual]<br />
<br />
== Evolution timeline==<br />
<br />
== Table of Prusa i3 variants==<br />
<br />
== Notes==<br />
<br />
[[Category:Prusa i3 Development]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=NEMA_17_Stepper_motor&diff=181354NEMA 17 Stepper motor2018-01-19T14:20:25Z<p>Merlucin: </p>
<hr />
<div>{{Vitamin<br />
|name = NEMA 17 Stepper motor<br />
|image = Motor-pap.png<br />
|description = A NEMA 17 sized stepper motor.<br />
|wikipedia = [[Wikipedia:Stepper motor|Stepper motor]]<br />
}}<br />
<br />
[[image:RepRap-NEMA-17.jpg|thumb|another NEMA-17 size motor]]<br />
<br />
<br />
A '''NEMA 17 stepper motor''' is a [[Stepper motor|stepper motor]] with a 1.7 x 1.7 inch (43.2 x 43.2 mm) faceplate. The NEMA 17 is larger and generally heavier than for example a NEMA 14, but this also means it has more room to put a higher torque. However, its size is ''not'' an indication of its power.<br />
<br />
== Dimensions ==<br />
[[File:Step motor nema 17 stepper motor.jpg|450px]]<br />
<br />
<br />
== Common Stepper Motor Models ==<br />
<br />
The most commonly used stepper motors in Reprap&ndash;based 3D printers are the Kysan 1124090/42BYGH4803, Rattm 17HS8401, and Wantai 42BYGHW609.<br />
<br />
However, motors close to NEMA 17 size, with approximately the following specifications, can also work:<br />
<br />
* 1.5A to 1.8A current per phase<br />
* 1-4 volts<br />
* 3 to 8 mH inductance per phase<br />
* 44 N&middot;cm (62oz&middot;in, 4.5kg&middot;cm) or more holding torque<br />
* 1.8 or 0.9 degrees per step (200/400 steps/rev respectively)<br />
<br />
''You are welcome to add information on any stepper motor you encounter, but please add only steppers (not other motors), which were tested to actually work on some or all printers.''<br />
<br />
<!-- Please keep the tables in manufacturer-alphabetical order! --><br />
{| class="wikitable sortable" <br />
<br />
! Model !! Holding Torque !! Rated voltage !! Shaft !! Step angle !! Motor length !! Rated current !! Inductance<br />
|-<br />
| 42HT47|| 44&nbsp;N&middot;cm || 2.8&nbsp;V || Ø&nbsp;5&nbsp;mm Dual || 1.8° || 47&nbsp;mm<br />
|-<br />
| 42SHD0404-22 || 52&nbsp;N&middot;cm || 3.84&nbsp;V || Ø&nbsp;5&nbsp;mm Single || 1.8° || 48&nbsp;mm <br />
|-<br />
| 42BYGH4803(SKU&nbsp;1124030)|| 54.0&nbsp;N&middot;cm || 4.2&nbsp;V || Ø&nbsp;5&nbsp;mm single || 1.8° || 48&nbsp;mm<br />
|-<br />
| 42BYGH4803-DC (SKU&nbsp;1124090) || 54.0&nbsp;N&middot;cm || 4.2&nbsp;V || Ø&nbsp;5&nbsp;mm single || 1.8° || 48&nbsp;mm <br />
|- <br />
| LDO-42STH47-1684A || 50&nbsp;N&middot;cm || 2.8&nbsp;V || Ø&nbsp;5&nbsp;mm single or dual || 1.8° || 47&nbsp;mm || 1.68A || 2.8 mH<br />
|- <br />
| LDO-42STH47-1684AC || 50&nbsp;N&middot;cm || 2.8&nbsp;V || Ø&nbsp;5&nbsp;mm single or dual || 1.8° || 47&nbsp;mm || 1.68A || 2.8 mH<br />
|- <br />
| 4118S-62-07|| 31&nbsp;N&middot;cm || &nbsp; || Ø&nbsp;5&nbsp;mm || 1.8° || 34&nbsp;mm <br />
|-<br />
| 17HS4417 || 40.0&nbsp;N&middot;cm || 2.6&nbsp;V || Ø&nbsp;5&nbsp;mm single || 1.8° || 40&nbsp;mm || 1.7A || 2.8 mH<br />
|-<br />
| SM-42BYG011-25 || 23.0&nbsp;N&middot;cm || 12&nbsp;V || Ø&nbsp;5&nbsp;mm single || 1.8° || 34&nbsp;mm || 0.33A || 46 mH<ref>With such inductance, this stepper is incapable of any speed and is unusable for a printer, as are most very low current steppers.</ref><br />
|- <br />
| 17HS1011-20B || 28.0&nbsp;N&middot;cm || 4.8&nbsp;V || Ø&nbsp;5&nbsp;mm single || 1.8° || 34&nbsp;mm <br />
|-<br />
| 17HS3001-20B || 40.0&nbsp;N&middot;cm || 2.0&nbsp;V || Ø&nbsp;5&nbsp;mm single || 1.8° || 40&nbsp;mm || 1.2 A || 4.5 mH<br />
|-<br />
| 17HS5005-S24 || 44.0&nbsp;N&middot;cm || 3&nbsp;V || Ø&nbsp;5&nbsp;mm double || 1.8° || 48&nbsp;mm <br />
|-<br />
| 17HS6002-27B || 65.0&nbsp;N&middot;cm || 4.05&nbsp;V || Ø&nbsp;5&nbsp;mm single flat|| 1.8° || 60&nbsp;mm <br />
|-<br />
| 17HD2038E || 45.0&nbsp;N&middot;cm || &nbsp; || Ø&nbsp;5&nbsp;mm single || 1.8° || &nbsp; <br />
|-<br />
| 17HS19-1684S || 55&nbsp;N&middot;cm || 2.8&nbsp;V || Ø&nbsp;5&nbsp;mm single || 1.8° || 47&nbsp;mm || 1.68A || 2.8mH<br />
|-<br />
| KH42JM2B087C || 33&nbsp;N&middot;cm || 6.7&nbsp;V || Ø&nbsp;5&nbsp;mm single || 1.8° || 42&nbsp;mm<br />
|-<br />
| SY42STH47-1206A || 31.1&nbsp;N&middot;cm || 4.0&nbsp;V || Ø&nbsp;5&nbsp;mm single || 1.8° || 40&nbsp;mm || 1.2A || 2.8 mH<br />
|-<br />
| SY42STH47-1504A || 55.0 N&middot;cm || 2.8&nbsp;V || Ø&nbsp;5&nbsp;mm || 1.8° || 47&nbsp;mm <br />
|-<br />
| SY42STH47-1684A || 43.1&nbsp;N&middot;cm || 2.8&nbsp;V || Ø&nbsp;5&nbsp;mm single || 1.8° || 48&nbsp;mm<br />
|-<br />
| SY42STH47-1684B || 43.1&nbsp;N&middot;cm || 2.8&nbsp;V || Ø&nbsp;5&nbsp;mm double || 1.8° || 48&nbsp;mm<br />
|-<br />
|TB35HT36-1004A || 35.3&nbsp;N&middot;cm || 2.8&nbsp;V || Ø&nbsp;5&nbsp;mm single|| 1.8° || 36&nbsp;mm<br />
|-<br />
|TB35HT36-1004B || 35.3&nbsp;N&middot;cm || 2.8&nbsp;V || Ø&nbsp;5&nbsp;mm double|| 1.8° || 36&nbsp;mm<br />
|-<br />
|QSH4218-51-049 || 49&nbsp;N&middot;cm || &nbsp; || Ø&nbsp;5&nbsp;mm || 1.8° || 47&nbsp;mm <br />
|-<br />
| 42BYGH W811 || 47.0&nbsp;N&middot;cm || 3.1&nbsp;V || Ø&nbsp;5&nbsp;mm || 1.8° || 48&nbsp;mm || 2.5A || 1.8 mH <br />
|-<br />
| 42HB34F103AB || 23.5&nbsp;N&middot;cm || &nbsp; || Ø&nbsp;5&nbsp;mm single || 1.8° || 34&nbsp;mm <br />
|-<br />
| 42SHD0412-175S || 44&nbsp;N&middot;cm || 2.8&nbsp;V || Ø&nbsp;8mm&nbsp;mm dual L175mm || 1.8º || 44&nbsp;mm <br />
|-<br />
| 1704HS168A || 54&nbsp;N&middot;cm || 2.8&nbsp;V || Ø&nbsp;5&nbsp;mm single flat|| 1.8° || 48&nbsp;mm || 1.68A || 2.8mH<br />
|-<br />
| 1703HS168A || 44&nbsp;N&middot;cm || 2.8&nbsp;V || Ø&nbsp;5&nbsp;mm single flat|| 1.8° || 40&nbsp;mm || 1.68A || 3.6mH<br />
|-<br />
| 1704HD150AW || 55&nbsp;N&middot;cm || 4.2&nbsp;V || Ø&nbsp;5&nbsp;mm single flat|| 1.8° || 48&nbsp;mm<br />
|-<br />
| JK42HS34-1334AC || 22&nbsp;N&middot;cm || 2.8&nbsp;V || Ø&nbsp;5&nbsp;mm single flat|| 1.8° || 34&nbsp;mm || 1.33A || 2.5mH<br />
|-<br />
| 17HS16-2004S1 || 45&nbsp;N&middot;cm || - || Ø&nbsp;5&nbsp;mm single flat|| 1.8° || 40&nbsp;mm || 2A || 2.6mH<br />
|-<br />
| 17HS24-1206S || 65&nbsp;N&middot;cm || - || Ø&nbsp;5&nbsp;mm single flat|| 1.8° || 60&nbsp;mm || 1.2A || 7mH<br />
|-<br />
| 17HS6002-N27BA || 65&nbsp;N&middot;cm || 4.05&nbsp;V || Ø&nbsp;5&nbsp;mm single flat|| 1.8° || 60&nbsp;mm || 1.5A || 6.5mH<br />
|-<br />
| 17HS8401B || 52&nbsp;N&middot;cm || - || Ø&nbsp;5&nbsp;mm double || 1.8° || 48&nbsp;mm || 1.8A || 3.2mH<br />
|-<br />
|-<br />
|}<br />
<br />
== 0.9° Stepper Motor Models ==<br />
<br />
{| class="wikitable sortable" <br />
<br />
! Model !! Holding Torque !! Rated voltage !! Shaft !! Step angle !! Motor length !! Rated current !! Inductance<br />
|-<br />
| 42BYGHM809 || 48&nbsp;N&middot;cm || 3.06&nbsp;V || Ø&nbsp;5&nbsp;mm no flat|| 0.9° || 48&nbsp;mm || 1.7A || 2.8mH<br />
|-<br />
| 17HM19-2004S || 46&nbsp;N&middot;cm || - || Ø&nbsp;5&nbsp;mm|| 0.9° || 48&nbsp;mm || 2A || 3mH<br />
|-<br />
|}<br />
<br />
== Geared stepper ==<br />
<br />
{| class="wikitable sortable" <br />
<br />
! Model !! Holding Torque !! Rated voltage !! Shaft !! Step angle !! Motor length !! Rated current !! Inductance || Gear ratio<br />
|-<br />
| 1040222 || 220&nbsp;N&middot;cm || 2.6&nbsp;V || Ø&nbsp;8&nbsp;mm single flat|| 1.8° || 34+27&nbsp;mm || 1A || 3.5 mH || 5.2:1<br />
|- <br />
| 17HS1070-C5X|| 260&nbsp;N&middot;cm || 2&nbsp;V || Ø&nbsp;8&nbsp;mm single flat|| 1.8° || 34+27&nbsp;mm || 1.3A || 2.4 mH || 5:1<br />
|- <br />
| 1702HS040-AWP518|| 260&nbsp;N&middot;cm || 12&nbsp;V || Ø&nbsp;8&nbsp;mm single flat|| 1.8° || 34+31&nbsp;mm || 0.4A || 37 mH || 5.18:1<br />
|-<br />
|}<br />
<br />
{{reflist}}<br />
<br />
[[Category:Vitamin]] [[Category:Stepper motors]]<br />
<br />
== Where to buy? ==<br />
<br />
[http://store.thingibox.com/en/8-mechanical Thingibox]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Stepper_motor&diff=181353Stepper motor2018-01-19T13:57:43Z<p>Merlucin: </p>
<hr />
<div>{{Vitamin<br />
|name = Stepper motor<br />
|image = Motor-pap.png<br />
|description = A stepper motor (NEMA 17 size)<br />
|wikipedia = [[Wikipedia:Stepper motor|Stepper motor]]<br />
}}<br />
[[image:StepperMotor-reprap-stepper.jpg|thumb|The original RepRap, Darwin, used this stepper motor (NEMA 23 size).]]<br />
A '''stepper motor''' is [[Motor FAQ|one kind of electric motor]] used in the robotics industry. Stepper motors move a known interval for each pulse of power. These pulses of power are provided by a stepper [[motor driver]] and is referred to as a step. As each step moves the motor a known distance it makes them handy devices for repeatable positioning. There is a good [[Wikipedia:Stepper motor|article on Wikipedia]] explaining the technology behind stepper motors. The mechanical operation of a stepper motor is shown in [http://www.engineersgarage.com/articles/stepper-motors this article].<br />
<br />
== Properties ==<br />
<br />
=== Step angle ===<br />
Stepper motors have a step angle. A full 360° circle divided by the step angle gives the number of steps per revolution. For example, ''1.8° per full step'' is a common step size rating, equivalent to ''200 steps per revolution''.<br />
<br />
Most stepper motors used for a Mendel have a step angle of 1.8 degrees. It is sometimes possible to use motors with larger step angles, however for printing to be accurate, they will need to be geared down to reduce the angle moved per step, which may lead to a slower maximum speed.<br />
<br />
=== Micro stepping ===<br />
A stepper motor always has a fixed number of steps. Microstepping is a way of increasing the number of steps by sending a sine/cosine waveform to the coils inside the stepper motor. In most cases, micro stepping allows stepper motors to run smoother and more accurately.<br />
<br />
Microstepping between pole-positions is made with lower torque than with full-stepping, but has much lower tendency for mechanical oscillation around the step-positions and you can drive with much higher frequencies.<br />
<br />
If your motors are near to mechanical limitations and you have high friction or dynamics, microsteps don't give you much more accuracy over half-stepping. When your motors are 'overpowered' and/or you don't have much friction, then microstepping can give you much higher accuracy over half-stepping. You can transfer the higher positioning accuracy to moving accuracy too.<br />
<br />
=== Bipolar ===<br />
[[image:StepperMotor-bipolar_stepper_sch.png|thumb|The two coils of a bipolar motor.]]<br />
Bipolar refers to the internals of the motor, and each type has a different stepper driver circuit board to control them. In theory a RepRap could use a unipolar motor, but in practice most are bipolar. They are also the type of motors we are using in the RepRap Project's Mendel and Darwin designs.<br />
<br />
Bipolar motors are the strongest type of stepper motor. You identify them by counting the leads - there should be four or eight. They have two coils inside, and stepping the motor round is achieved by energising the coils and changing the direction of the current within those coils. This requires more complex electronics than a unipolar motor, so we use a [[stepper motor driver#Stepper driver chips | special driver chip]] to take care of all that for us. Some designs (the eight-wire ones) split each coil in the middle so you can wire the motor either as bipolar (short the middles) or unipolar (short the middles and treat the link as the centre tap - see below).<br />
<br />
=== Unipolar ===<br />
[[image:StepperMotor-unipolar_stepper_sch.png|thumb|The two coils of a unipolar motor, each with a centre tap.]]<br />
Unipolar motors also have two coils, but each one has a centre tap. They are readily recognizable because they have 5, 6 or even 8 leads. It is possible to drive 6 or 8 lead unipolar motors as bipolar motors if you ignore the centre tap wires. A 5 lead motor has both centre taps connected, so re-wiring them to a 4 lead version requires at least opening the motor, if it can be done at all.<br />
<br />
The main beauty of unipolar motors is that you can step them without having to reverse the direction of current in any coil, which makes the electronics simpler. Some early RepRap prototypes used this trick. Because the centre tap is used to energise only half of each coil at a time, unipolar motors generally have less torque than bipolar motors.<br />
<br />
<br />
=== Holding torque ===<br />
Stepper motors do not offer as much torque or holding force as comparable DC servo motors or DC gear motors. Their advantage over these motors is one of positional control. Whereas DC motors require a closed loop feedback mechanism, as well as support circuitry to drive them, a stepper motor has positional control by its nature of rotation via fractional increments.<br />
<br />
The Mendel officially requires approximately 13.7 N&middot;cm torque (19.4 ozf&middot;in) of holding torque (or more) for each of the X, Y and Z axis motors to avoid issues, although one stepper with less has been used successfully (see below). Recent designs for extruders ([[ExtruderController]]) almost exclusively require stepper motors as well, but no torque requirements have been given in those designs. If in doubt, higher is better.<br />
<br />
For [[Wade's Geared Extruder]] (most widely used one as of 2012) it is suggested to use motor that is capable of creating a holding torque of at least 40 N&middot;cm.<br />
<br />
If you need to convert between different units for the torque you can use the [http://www.numberfactory.com/nf%20torque.htm torque unit converter].<br />
<br />
In September 2013, [[User:Willy|Willy]] did a comparison of a number of commonly used NEMA17 [[Stepper torque | steppers and their torque]] at various speeds.<br />
<br />
=== Size ===<br />
The physical size of stepper motors are usually described via a US-based [[NEMA Motor|NEMA standard]], which describes the bolt-up pattern and shaft diameter. In addition to the NEMA size rating, stepper motors are also rated by the depth of the motor in mm. Typically, the power of a motor is proportional to the physical size of the motor.<br />
<br />
If using the smaller [[NEMA 14 Stepper motor|NEMA 14 motors]], aim for the high torque option. NEMA 14s are neater, lighter and smaller, but can be hard to obtain with the appropriate holding torque. [[NEMA 17 Stepper motor|NEMA 17s]] are quite easy to get in the specification that Mendel needs, but are bulkier and less neat. NEMA 14s are running near the edge of their envelope: they will get warm. NEMA 17s are well inside what they can do, and will run much cooler.<br />
<br />
=== NEMA ===<br />
: ''main: [[NEMA Motor]]''<br />
Refers to the frame size of the motor as standardized by the US [http://en.wikipedia.org/wiki/National_Electrical_Manufacturers_Association National Electrical Manufacturers Association] in its [http://classxboats.com/htdocs/Engineering_Research/NEMA/ics_16.pdf Publication ICS 16-2001]. It specifies the 'face' size of the motor but not its length. For example a NEMA 23 stepper has a face of 2.3 x 2.3 inches with screw holes to match. Note: just because a motor is bigger does not mean it is more powerful in terms of torque. It is perfectly possible for a NEMA 14 to 'out pull' a NEMA 17 or a NEMA 23.<br />
<br />
Based upon the NEMA 17 specification (from what I can find) the mounting holes are spaced 31 mm (1.22 inch) apart along the edge of the motor. This should help if you are using second-hand/salvaged parts.<br />
<br />
=== Shaft ===<br />
Any part that goes on a stepper motor shaft expects the shaft to be roughly Ø 5 mm. If the shaft is a different size, you will need to make allowances for this in the (plastic) parts you obtain/make.<br />
<br />
=== Wiring ===<br />
Steppers motors come in several wiring configurations. It is fairly common to find 4, 6 and 8 wires, and these work fine with the standard RepRap electronics.<br />
Stepper motors with 5 wires exist but won't work with the standard RepRap electronics, because the 5th wire connects to both coil centers. See [[stepper wiring]] for more details.<br />
<br />
=== Heat ===<br />
Most of the motors specs give the current for two coils that will give an 80 °C rise, i.e. they can run at 100 °C! When using them on plastic brackets you need to under-run them to keep the brackets from melting. With PLA's glass transition temperature between 60-65 °C, you have to seriously under-run them! Fortunately temperature rise is proportional to power, which is in turn proportional to the square of current (P=I<sup>2</sup>R), but torque is directly proportional so you can keep temperature under control without losing too much torque. For example, running a stepper at 70% of the rated current would result 70% of the torque and 49% (0.7<sup>2</sup>=0.49) of the power dissipation and thermal rise.<br />
<br />
=== Power and current ===<br />
All recent stepper controllers use a current-limiting design. Because of this, the resistance (ohms, Ω) of the coils doesn't matter, as long as it is low enough for the current to rise fast enough for the current-limiting design to come into play. If the resistance is too high (i.e. 24 V steppers) the current simply doesn't raise enough. For this reason, stepper motors rated for 3-5 V and 1-1.5 A are generally recommended, as these motors will perform near their peak torque with a current-limiting stepper controller (such as a Pololu A4988).<br />
<br />
Designs which use a separate "extruder controller board" sometimes use H-bridges (which are designed for running a DC motor) instead of a proper current-limiting stepper controller. On these boards, you need to be careful not to turn the current (PWM) too high, especially with low-ohm (low voltage) motors. You run the risk of overheating both the stepper motor and the H-bridge chip.<br />
<br />
== Getting and using your stepper motors ==<br />
<br />
=== Purchasing a motor ===<br />
The following are unscientific rules of thumb for purchasing the right motor:<br />
<br />
# Generally, the longer the motor body, the more torque the motor has.<br />
# If a motor is rated to more amps or volts than your driver can produce, your motor will not produce the manufacturer's rated torque.<br />
# A motor can safely exceed its rated voltage with a chopping stepper driver (which is all the RepRap stepper drivers, save only the Gen3 electronics extruder board hack). A motor that exceeds its rated current (amps) will severely overheat and die a quick death.<br />
# Stepper motors are generally rated for a 50 °C temperature rise at rated current/torque.<br />
# ABS melts at 105-120 °C but softens at 80 °C. Therefore you probably can't run your steppers at their full rated torque without melting your plastic motor mounts.<br />
# Power is measured in watts (W) and is calculated as volts (V) × current (A).<br />
# Power made available to a motor will be turned into heat and motion.<br />
# The more power made available to the motor the higher the amount of heat and motion. Heat is proportional to current squared while motion is proportional to current, so losing a little motion (torque) can lose a lot of heat.<br />
# Current and torque are related. The more current, the more torque. More current also means more power requirement and more heat on motor and stepper driver.<br />
# A motor's rated amps, volts, or ohms (if missing from the spec sheet) can be calculated with the other two numbers using [[Wikipedia:Ohm's law|Ohm's law]]. Or you can cheat and use a [http://www.ohmslawcalculator.com/ohms_law_calculator.php calculator].<br />
<br />
''Does the rule of thumb at''<br />
''[http://techref.massmind.org/techref/io/stepper/estimate.htm Massmind: Estimating Stepper Motor Size]''<br />
''work for RepRaps/RepStraps?''<br />
<br />
=== Models ===<br />
<br />
The different stepper motor models can be found on their respective pages:<br />
<br />
* [[NEMA 08 Stepper motor]]<br />
* [[NEMA 11 Stepper motor]]<br />
* [[NEMA 14 Stepper motor]]<br />
* [[NEMA 17 Stepper motor]]<br />
* [[NEMA 23 Stepper motor]]<br />
<br />
=== Discovering unknown motors ===<br />
<br />
For starters, see what [[User:Traumflug | Traumflug]] [http://forums.reprap.org/read.php?249,223405,223467#msg-223467 wrote in the forum] (in german).<br />
<br />
=== Driving stepper motors ===<br />
<br />
To control your stepper motor, you'll need a [[stepper motor driver]].<br />
<br />
=== Wiring Your Stepper ===<br />
<br />
See [[Stepper wiring]].<br />
<br />
=== Electro-mechanical linear actuators ===<br />
As an alternative, rather than the motor spinning the lead screw as in most CNC designs, a [[Wikipedia:Linear actuator#Electro-mechanical actuators|linear actuator]] spins an internal lead nut. This pulls the motor up and down a stationary lead screw that passes all the way through the motor. The electronics works identically to other stepper motors - standard stepper motor electronics can drive it. One RepRap researcher points out that this makes the mechanics simpler and, with a few changes to the design, could potentially lower total cost of a RepRap. See [http://builders.reprap.org/2008/04/first-tests-of-haydon-linear-actuator.html First tests of the Haydon linear actuator stepper motor][http://web.archive.org/web/20120502194754/http://www.3dreplicators.com/cgi-bin/cblog/index.php?/archives/391-Engaging-the-windmill.html][http://web.archive.org/web/20120716022616/http://www.3dreplicators.com/cgi-bin/cblog/index.php?/archives/454-Selecting-a-linear-actuator-for-the-T2-z-axis.html] by Forrest Higgs.<br />
<br />
== History ==<br />
<br />
=== Darwin (RepRap v1.0) ===<br />
The RepRap Darwin used a NEMA 23 stepper motor. This stepper motor was a unipolar stepper motor which could be configured as a bipolar. This design used 3 stepper motors, one for each axis, and a DC motor for its extruder. Later many people upgraded their extruders to increase their control of the extruder. <br />
<br />
Note the Generation 2 electronics supported the first configuration with 3 stepper driver circuit boards for the steppers and a PWM circuit board to control the DC motor.<br />
<br />
The Darwin stepper motor requirements were as follows:<br />
<br />
{| class="wikitable"<br />
|- style="background-color:#f0f0f0;"<br />
! Parameter !! Specification<br />
|-<br />
| Size || NEMA 23 <br />
|-<br />
| Type || Bipolar <br />
|-<br />
| Shaft || Dual-output shaft<br />
|-<br />
| Torque || 71 N&middot;cm (100 oz&middot;in)<br />
|-<br />
| Resistance || about 10 Ω, or 1 to 30 Ω <br />
|}<br />
<br />
Note: If you are using the [[DarwinStepperController_1_2|PIC controller]] (Note: Generation 1 electronics) you need a motor that will use about 1A per winding at 12V - that is, around 10 ohms. The Arduino circuit can be adjusted to accommodate a wider range of steppers, but remember that if you specify a low-resistance one and the Arduino controller has to chop the voltage to limit the current going through it, that will also limit the torque.<br />
<br />
Comments: Nema23 stepper motor is NOT the best choice for Darwin or other reprap strong 3d printers if you use a 2A stepper driver. At least 24V power supply for a Nema23 stepper and a strong stepper driver up to 3A or 4A are ideal. So if you use 12V and a stepper driver within 2A drive ability, a Nema17 long body stepper motor is recommend or a geared stepper motor is good. A Nema17 60mm stepper motor can have 0.65N.m holding torque. In the other side, a Nema17 60mm stepper motor is much cheaper than a Nema23 stepper or a geared nema17 stepper motor. --[[User:Robotdigg|Robotdigg]] 03:47, 30 July 2013<br />
<br />
Comment to the comment: NEMA23 steppers work at 12&nbsp;V just as fine as NEMA17 ones. The bigger diameter results in more torque at the cost of some speed. Speed is rarely a limitation on belt driven drives. --[[User:Traumflug|Traumflug]] 06:26, 30 July 2013 (UTC)<br />
<br />
=== Mendel (RepRap v2.0) ===<br />
The RepRap Mendel used either NEMA 17 or NEMA 14 bipolar stepper motors. It used four stepper motors: one for each of the three axes and one for the extruder. <br />
<br />
Note this configuration of four stepper motors was supported by the 3rd generation electronics.<br />
<br />
The Mendel stepper motor requirements were as follows:<br />
<br />
{| class="wikitable"<br />
|- style="background-color:#f0f0f0;"<br />
! Parameter !! Specification<br />
|-<br />
| Size || NEMA 17 or 14 (prototype was NEMA 14)<br />
|-<br />
| Type || Bipolar <br />
|-<br />
| Shaft || Dual-output shaft (need to make knurling the stepper shaft easier, not applicable to recent geared extruders)<br />
|-<br />
| Torque || 13.7 N&middot;cm (19.4 oz&middot;in)<br />
|-<br />
| Resistance || Must be over 6 Ω (not applicable to recent stepper controllers, see [[#Power and current|Power and current]] above)<br />
|}<br />
<br />
== Further reading ==<br />
*[[Stepper motor driver]]<br />
*[[Motor control loop]]<br />
*[[NEMA_17_Stepper_motor]]<br />
*[[Printed stepper motors]]<br />
*[[Choosing_stepper_for_a_delta]]<br />
<br />
* [http://www.geckodrive.com/gecko/images/cms_files/Step%20Motor%20Basics%20Guide.pdf] Some details about steppers and driver electronics<br />
<br />
<br />
[[Category:General motion control]]<br />
[[Category:Stepper motors| ]]<br />
<br />
== Where to buy? ==<br />
<br />
[http://store.thingibox.com/en/8-mechanical Nema 14,17 and 23] from Thingibox.</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Clone_Wars:_Tiendas/es&diff=181309Clone Wars: Tiendas/es2018-01-17T15:49:14Z<p>Merlucin: /* Servicios de Corte */</p>
<hr />
<div>{{Languages|Clone_Wars:_Tiendas}} <br />
== Tiendas ==<br />
Sección donde se listan por orden alfabético las tiendas donde es posible encontrar componentes para tu impresora 3d:<br />
=== On-line España ===<br />
<br />
{| class="wikitable sortable"<br />
|- style="background-color:#f0f0f0;"<br />
! style="vertical-align: bottom;" | Tienda<br />
! style="vertical-align: bottom;" | Localización<br />
! {{Vertical|2em|16em|&nbsp;Kits&nbsp;completos}}<br />
! {{Vertical|2em|16em|&nbsp;Piezas&nbsp;impresas}}<br />
! {{Vertical|2em|16em|&nbsp;Electrónica}}<br />
! {{Vertical|2em|16em|&nbsp;Motores}}<br />
! {{Vertical|2em|16em|&nbsp;Fusores&nbsp;y&nbsp;extrusores}}<br />
! {{Vertical|2em|16em|&nbsp;Rodamientos,&nbsp;varillas,&nbsp;correas, &nbsp;poleas&nbsp;y&nbsp;mecánica&nbsp;en&nbsp;general}}<br />
! {{Vertical|2em|16em|&nbsp;Consumibles}}<br />
! {{Vertical|2em|16em|&nbsp;Servicio&nbsp;de&nbsp;impresión &nbsp;y&nbsp;prototipado}}<br />
! {{Vertical|2em|16em|&nbsp;Cursos&nbsp;y&nbsp;talleres}}<br />
! style="vertical-align: bottom;" | Desarrolladores de...<br />
! style="vertical-align: bottom;" class="unsortable" | Reseñas<br />
|-<br />
| [http://www.3dcpi.com/ 3DCPI] || Barcelona<br />
| &#x2713; || || || || || || &#x2713; ||||&#x2713; <br />
| ||<br />
|-<br />
| [http://3despana.com/ 3DEspana.com] || Madrid<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| [[Ulticampy]] ||<br />
|-<br />
| [http://3dinvasion.com/ 3Dinvasion] || Canarias<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || || &#x2713;<br />
| ||<br />
|-<br />
| [http://3dmatic.es/ 3Dmatic] || Valencia<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||<br />
| ||<br />
|-<br />
| [http://www.3dorobotics.com/tienda/ 3DoRobotics] || Valladolid<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; <br />
| ||<br />
|-<br />
| [http://www.3dprinters-shop.com/es/ 3DPrinters-shop] || Málaga<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||&#x2713;<br />
| [[Prusa MAXI & Prusa MEGA]] ||<br />
|-<br />
| [http://www.3dpenedes.com/ 3DPenedes] || Barcelona<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; <br />
| ||<br />
|-<br />
| [http://www.3dsmart.es/ 3DSmart] || Jaén<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||<br />
| ||<br />
|-<br />
| [http://bcndynamics.com/ BCN Dynamics] || Barcelona<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||<br />
| [http://bcndynamics.com/es/MaduixaCNC MaduixaCNC] [http://bcndynamics.com/es/product/frax-3d Frax3D] ||<br />
|-<br />
| [http://chupacabras3d.com/ Chupacabras3D] || Barcelona<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || || ||<br />
| Aceptamos Bitcoin <br />
|-<br />
| [http://clonemaker3d.com/ CloneMaker3D]|| Zaragoza<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| ||<br />
|-<br />
| [http://shop.createc3d.com/ Createc 3D Shop] || Granada<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||&#x2713;<br />
| ||<br />
|-<br />
| [http://domotek.es/ DomoTek] || San Sebastián<br />
| || || || || || || &#x2713; || &#x2713; ||<br />
| ||<br />
|-<br />
| [https://www.DIYania.com/ DIYania] || Sevilla<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| En pedidos nacionales superiores a 50€ el envío es gratuito.<br />
|-<br />
| [https://www.en3dstudios.com/ en3DStudios] || Barcelona<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| Distribuidor Oficial Europa CR-10 (Creation Reality) <br />
|-<br />
| [http://www.fffworld.com/ FFF World] || Álava<br />
| || || || || || || &#x2713; || ||<br />
| ||<br />
|-<br />
| [http://www.filament2print.com/ Filament2print] || A Coruña<br />
| &#x2713; || || || || || || &#x2713; || || &#x2713;<br />
| ||<br />
|-<br />
| [http://gades3d.es/tienda/ Gades3D] || Cádiz<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713;<br />
| ||<br />
|-<br />
| [https://garagedays3d.com/es/ Garage Days 3D] || Súria<br />
| || &#x2713; || &#x2713; || &#x2713; || || &#x2713; || &#x2713; || &#x2713; || <br />
| ||<br />
|-<br />
| [http://www.iberobotics.com/shop/index.php?cPath=94 IBEROBOTICS Shop] || Santander<br />
| &#x2713; || || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| ||<br />
|-<br />
| [http://ifusionshop.com/ iFusionShop] || Tarragona<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||<br />
| ||<br />
|-<br />
| [http://impresoras3dlowcost.com/ Impresoras3DLowCost.com] || Córdoba<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| ||<br />
|-<br />
| [http://onlineshop.iniciativas3d.com/Iniciativas3D Iniciativas3D] || Córdoba y Málaga<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||<br />
| ||<br />
|-<br />
| [http://www.kitprinter3d.com/ KitPrinter3D ] || Madrid<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| ||<br />
|-<br />
| [http://www.lemonstore.es/ LemonStore] || Murcia<br />
| &#x2713; || || || || || || &#x2713; || ||<br />
| ||<br />
|-<br />
| [http://malagamakers.es/ MalagaMakers] || Málaga<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||&#x2713;<br />
| ||<br />
|-<br />
| [http://makergal.es/ MakerGal] || Santiago de Compostela<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||&#x2713;<br />
| [[Mendel Max XL]] ||<br />
|-<br />
| [https://moebyus.com/ Moebyus Machines] || Madrid<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||&#x2713;<br />
| [SIRIUS], One, Melta XL, M3, Amigo || También tienda física <br />
|-<br />
| [http://mprime.io/ M Prime] || Madrid<br />
| || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || || || <br />
| [http://mprime.io/es/m-prime-one M Prime One]||<br />
|-<br />
| [http://orballoprinting.com/ Orballo Printing] || Vigo<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || || <br />
| || <br />
|-<br />
| [http://plasticdreams.es/shop Plastic Dreams] || Murcia<br />
| &#x2713; || &#x2713; || &#x2713; || || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || [http://plasticdreams.es/producto/kit-p3steel-extension-200x300/ Extensión eje Y para P3Steel] ||<br />
|-<br />
| [https://www.impresora3d.es/ Printed Dreams] || Madrid/Cartagena<br />
| &#x2713; || || || || || || &#x2713; || &#x2713; || &#x2713;<br />
| ||<br />
|-<br />
| [http://presolid.com/es/ PRESolid Tech] || Barcelona<br />
| &#x2713; || || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || || &#x2713;<br />
| [http://presolid.com/es/content/category/2-productos ResinCAT] ||<br />
|-<br />
| [http://www.staticboards.es/productos/ StaticBoards] || A Coruña<br />
| || || &#x2713; || || || || || ||<br />
| [http://www.staticboards.es/productos/ramps14sb/ RAMPS 1.4SB] ||<br />
|-<br />
| [http://store.thingibox.com/ ThingiBOX] || Barcelona<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713;<br />
| [http://store.thingibox.com/es/22-ion-v6 ION V6 y V6 XL] || Envíos a todo el mundo<br />
|}<br />
<br />
=== ENLACES EN CUARENTENA ===<br />
(dan error de carga - se eliminarán a los 60 dias)<br />
<br />
{| class="wikitable sortable"<br />
|- style="background-color:#f0f0f0;"<br />
! style="vertical-align: bottom;" | Tienda<br />
! style="vertical-align: bottom;" | Localización<br />
! {{Vertical|2em|16em|&nbsp;Kits&nbsp;completos}}<br />
! {{Vertical|2em|16em|&nbsp;Piezas&nbsp;impresas}}<br />
! {{Vertical|2em|16em|&nbsp;Electrónica}}<br />
! {{Vertical|2em|16em|&nbsp;Motores}}<br />
! {{Vertical|2em|16em|&nbsp;Fusores&nbsp;y&nbsp;extrusores}}<br />
! {{Vertical|2em|16em|&nbsp;Rodamientos,&nbsp;varillas,&nbsp;correas, &nbsp;poleas&nbsp;y&nbsp;mecánica&nbsp;en&nbsp;general}}<br />
! {{Vertical|2em|16em|&nbsp;Consumibles}}<br />
! {{Vertical|2em|16em|&nbsp;Servicio&nbsp;de&nbsp;impresión &nbsp;y&nbsp;prototipado}}<br />
! {{Vertical|2em|16em|&nbsp;Cursos&nbsp;y&nbsp;talleres}}<br />
! style="vertical-align: bottom;" | Desarrolladores de...<br />
! style="vertical-align: bottom;" class="unsortable" | FECHA ERROR<br />
|-<br />
| [http://madrid3dprint.com/ madrid3DPrint] || Madrid<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| || 20/5/17<br />
|-<br />
| [http://www.nativa3d.com Nativa3D] || Cádiz<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713;<br />
| || 20/5/17<br />
|-<br />
| [http://shop.reclone3d.com/ Reclone3D] || Málaga<br />
| || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||<br />
| [[J Head Hispania]] || 20/5/17<br />
|}<br />
<br />
<br />
<br />
=== On-line (Resto del Mundo) ===<br />
<br />
Europa:<br />
* [http://www.mendel-parts.com/ Mendel parts] (Holanda)<br />
* [http://www.xyzprinters.com/ http://www.xyzprinters.com/] (Holanda)<br />
* [http://shop.arcol.hu/ arcol.hu] (Hungría) <br />
* [https://shop.grrf.de/ German RepRap fundation] (Alemania)<br />
* [http://reprapsource.com/ reprapsource.com]<br />
* [http://reprapworld.com/ Reprap world] (Holanda) [filamento]<br />
* [https://0xfb.com/shop.html Future Bits] La tienda de Kliment! (Alemania)<br />
* [http://www.hotends.com/ hotends]<br />
* [http://www.orbi-tech.de/index_english.htm Orbi-tech]. Plástico (Alemania)<br />
* [http://reprap-3d-printer.com/ Reprap-3D-printer] (Francia)<br />
<br />
EEUU / América (ojo aduanas)<br />
* [http://www.makergear.com/ Makergear] (EEUU)<br />
* [http://www.lulzbot.com/en/ Lulzbot] (EEUU)<br />
* [http://gala-automation.com/ Gala automation] (EEUU)<br />
* [http://techpaladin.com/ techpaladin] (EEUU)<br />
* [http://www.centralreprap.com/prestashop/ CentralReprap]<br />
* [http://ultimachine.com/ Ultimachine] (EEUU)<br />
* [http://www.makermex.com/ MakerMex] (México)<br />
* [http://www.3dm.mx/ 3DM] (México) Impresoras 3D RepRap al Mejor Precio de México. Entrega Inmediata, consumibles y componentes.<br />
* [http://www.impresoras3dprusai3.com.mx/ Impresoras 3D en México] (CIUDAD DE MEXICO) D.F. Kit Prusa i3 Steel con marco en acero estructural, varillas acero inoxidable.<br />
* [massieu11@gmail.com] (CIUDAD DE MEXICO) sur del D.F. massieu11@gmail.com Componentes para armar tu impresora 3D excelente atención y servicio, banda, poleas, arduino,rodamientos, bujes de bronce, varilla lisa rectificada, banda cerrada/abierta, motores, hotend, cama caliente, kapton, ramps, LCD etc.<br />
<br />
Otros <br />
* [http://www.3dacessorieshub.com/ 3D Acessories Hub ].Una ventanilla única para todos los componentes de RepRap y las impresoras 3D<br />
* [http://www.goodluckbuy.com/ http://www.goodluckbuy.com/]. Tienda en china donde venden motores, varillas roscadas...<br />
* [http://www.futurlec.com/ Futurlec] Electrónica en general<br />
* [http://www.taydaelectronics.com/ Tayda Electronics] Electrónica en general<br />
* [http://www.dealextreme.com/ Dealextreme] Tienda china con prácticamente cualquier cosa. (contrasta precios antes de comprar)<br />
* [http://www.bitsbox.co.uk/ BitsBox] Componentes electrónicos, algunos especialmente baratos. Envía por ~3€<br />
* [http://www.emakershop.com/ eMAKERshop] Tienda online que vende productos de varios vendedores externos, como un portal de venta.<br />
* [http://www.zappautomation.co.uk/index.php?language=ES Zappautomation] Tienda con todo tipo de productos para CNCs (UK)<br />
* [http://makemendel.com/ Makemendel]<br />
* [http://www.ebay.com/itm/1pc-200mm-X-100ft-High-Temperature-Resistant-Kapton-Tape-/170864710486?ssPageName=ADME:L:OU:ES:3160 Kapton en eBay]: Cinta kapton de 20cm de ancho<br />
* [http://www.reprap.cc/ Reprap Austria] Tienda de todo tipo de material para Reprap tambien en ebay: [http://www.ebay.es/sch/reprapper/m.html?_nkw=&_armrs=1&_from=&_ipg=&_trksid=p3686 reprapper]<br />
<br />
<br />
<br />
=== Otros enlaces de Interés ===<br />
<br />
<br />
* [http://www.copsula.es/ '''Copsula'''] (Chiclana - Cádiz) Centro multidisciplinar de referencia para makers, artistas, musicos y diversos gremios. Punto de recogida y taller de http://www.gades3d.es/ , impresoras 3D, consumibles, repuestos, Arduino, Raspberry-pi, Meriendas Makers, Cursos, Venta y reparacion de informatica (PC y MAC), Distribuidor Oficial BQ.<br />
* [http://www.madtek3d.com/ '''MADTEK3D''']Empresa de Córdoba dedicada a la venta de Impresoras 3D, componentes y consumibles. Filamento de alta calidad y precios bajos. ¡Ampliando catálogo!<br />
* [http://shop.menextech.com/index.php MENEXTECH] (España) Todo lo necesario para que construyas tu impresora y componentes informaticos.<br />
* [http://www.moebyus.com/ Moebyus Machines ](España) Envío en 24h. Impresoras, partes, consumibles, repuestos, etc. Impresión bajo demanda, modelado, cursos. Tienda física en Principe de Vergara 206, Madrid.<br />
* [http://www.plabs3d.com/ '''Plabs 3D'''] - Extenso catálogo de filamentos para impresora 3D - Máxima calidad - Donostia (Gipuzkoa)<br />
* [http://www.rationalstock.es/ Rational Stock] (España) Ferretería online. Variedad y buenos precios para tornillería. Permite comprar por unidades. Envío económico en 24-48 horas.<br />
* [http://www.repparts3d.com/ '''RepParts 3D'''] (España) ABS, PLA, Conductor, Termocrómico, LayWood, LayBrick, Glow in the Dark, Nylon, HIPS. Con la mas amplia gama de colores<br />
<br />
<br />
=== Tiendas Físicas ===<br />
<br />
* [[Clone_wars:_Tiendas_en_Andalucia|Andalucía]]<br />
* [[Clone_wars:_Tiendas_en_asturias|Asturias]]<br />
* [[Clone_wars:_Tiendas_en_barcelona|Barcelona]]<br />
* [[Clone_wars:_Tiendas_en_burgos|Burgos]]<br />
* [[Clone_wars:_Tiendas_en_Cantabria|Cantabria]]<br />
* [[Clone_wars:_Tiendas_en_castellon|Castellón]]<br />
* [[Clone_wars:_Tiendas_en_galicia|Galicia]]<br />
* [[Clone_wars:_Tiendas_en_leon|León]]<br />
* [[Clone_wars:_Tiendas_en_madrid|Madrid]]<br />
* [[Clone_wars:_Tiendas_en_navarra|Navarra]]<br />
* [[Clone_wars:_Tiendas_en_valencia|Valencia]]<br />
* [[Clone_wars:_Tiendas_en_zaragoza|Zaragoza]]<br />
[http://goo.gl/maps/Md32Y Mapa] de tiendas y talleres<br />
<br />
<br />
=== LISTA NEGRA DE TIENDAS ===<br />
<br />
Tiendas con las que hemos tenido malas experiencias:<br />
* [http://myworld.ebay.es/drumas09/ drumas09] (UK). Este vendedor no envía los pedidos. Pedro tuvo un problema con este vendedor.<br />
<br />
* [http://www.leon-3d.es/ LEÓN 3D]. Ha habido problemas de licencias CC con algunos productos de esta empresa. [https://groups.google.com/forum/#!topic/asrob-uc3m-impresoras-3d/CXieuC0XtD0 Más datos en este hilo].<br />
<br />
<br />
== Servicios de Corte ==<br />
<br />
'''Cortenfrio'''<br />
*Empresa de corte en frio ubicada en Zaragoza.<br />
*[http://cortenfrio.com/index.htm Cortenfrio]<br />
<br />
'''Nativa3D Technologies'''<br />
*Servicios de Corte en Láser, Agua y Plasma<br />
*[http://www.nativa3d.com/ Nativa3D Technologies]<br />
*Email: contacto@nativa3d.com<br />
*Teléfono: 615 01 00 92<br />
<br />
'''Laserebro'''<br />
*Son un grupo de empresas con muchas sedes, tienes una cerca de casa seguro :D mira en el mapa de localizacion, en su web, en el apartado: Grupo Láser Ebro.<br />
*[http://www.laserebro.com/frame1.htm Laserebro]<br />
<br />
'''Naivan'''<br />
*Empresa de corte por Laser y otros servicios en Vitoria.<br />
*[http://www.naivan.com/ Naivan]<br />
*Email para enviar los planos de corte: naivan@naivan.com (enviar en dxf o pdf acotado)<br />
*Teléfono:945 259 857<br />
<br />
'''HJL'''<br />
*Empresa de corte por Laser y otros servicios en Murcia.<br />
*[http://www.hjl.es/ HJL]<br />
*Teléfono:968 802 044<br />
<br />
'''ThingiBOX'''<br />
*Corte por Laser en Viladecans (Barcelona).<br />
*[http://www.thingibox.com/ ThingiBOX]<br />
*Teléfono: 931 462 701 <br />
<br />
'''Acottado'''<br />
*Empresa de corte por laser ubicada en Leganés (Madrid).<br />
*[http://acottado.com/laser/ Acottado]<br />
<br />
<br />
<br />
{| class="wikitable"<br />
|-<br />
|<br />
[[File:Clone-Wars-logo.png|border|100px|link=Proyecto Clone Wars]]<br />
| [[Proyecto Clone Wars]]<br />
|}<br />
<br />
[[Category:Clone wars/es]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Clone_Wars:_Tiendas/es&diff=181307Clone Wars: Tiendas/es2018-01-17T15:36:29Z<p>Merlucin: /* On-line España */</p>
<hr />
<div>{{Languages|Clone_Wars:_Tiendas}} <br />
== Tiendas ==<br />
Sección donde se listan por orden alfabético las tiendas donde es posible encontrar componentes para tu impresora 3d:<br />
=== On-line España ===<br />
<br />
{| class="wikitable sortable"<br />
|- style="background-color:#f0f0f0;"<br />
! style="vertical-align: bottom;" | Tienda<br />
! style="vertical-align: bottom;" | Localización<br />
! {{Vertical|2em|16em|&nbsp;Kits&nbsp;completos}}<br />
! {{Vertical|2em|16em|&nbsp;Piezas&nbsp;impresas}}<br />
! {{Vertical|2em|16em|&nbsp;Electrónica}}<br />
! {{Vertical|2em|16em|&nbsp;Motores}}<br />
! {{Vertical|2em|16em|&nbsp;Fusores&nbsp;y&nbsp;extrusores}}<br />
! {{Vertical|2em|16em|&nbsp;Rodamientos,&nbsp;varillas,&nbsp;correas, &nbsp;poleas&nbsp;y&nbsp;mecánica&nbsp;en&nbsp;general}}<br />
! {{Vertical|2em|16em|&nbsp;Consumibles}}<br />
! {{Vertical|2em|16em|&nbsp;Servicio&nbsp;de&nbsp;impresión &nbsp;y&nbsp;prototipado}}<br />
! {{Vertical|2em|16em|&nbsp;Cursos&nbsp;y&nbsp;talleres}}<br />
! style="vertical-align: bottom;" | Desarrolladores de...<br />
! style="vertical-align: bottom;" class="unsortable" | Reseñas<br />
|-<br />
| [http://www.3dcpi.com/ 3DCPI] || Barcelona<br />
| &#x2713; || || || || || || &#x2713; ||||&#x2713; <br />
| ||<br />
|-<br />
| [http://3despana.com/ 3DEspana.com] || Madrid<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| [[Ulticampy]] ||<br />
|-<br />
| [http://3dinvasion.com/ 3Dinvasion] || Canarias<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || || &#x2713;<br />
| ||<br />
|-<br />
| [http://3dmatic.es/ 3Dmatic] || Valencia<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||<br />
| ||<br />
|-<br />
| [http://www.3dorobotics.com/tienda/ 3DoRobotics] || Valladolid<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; <br />
| ||<br />
|-<br />
| [http://www.3dprinters-shop.com/es/ 3DPrinters-shop] || Málaga<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||&#x2713;<br />
| [[Prusa MAXI & Prusa MEGA]] ||<br />
|-<br />
| [http://www.3dpenedes.com/ 3DPenedes] || Barcelona<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; <br />
| ||<br />
|-<br />
| [http://www.3dsmart.es/ 3DSmart] || Jaén<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||<br />
| ||<br />
|-<br />
| [http://bcndynamics.com/ BCN Dynamics] || Barcelona<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||<br />
| [http://bcndynamics.com/es/MaduixaCNC MaduixaCNC] [http://bcndynamics.com/es/product/frax-3d Frax3D] ||<br />
|-<br />
| [http://chupacabras3d.com/ Chupacabras3D] || Barcelona<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || || ||<br />
| Aceptamos Bitcoin <br />
|-<br />
| [http://clonemaker3d.com/ CloneMaker3D]|| Zaragoza<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| ||<br />
|-<br />
| [http://shop.createc3d.com/ Createc 3D Shop] || Granada<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||&#x2713;<br />
| ||<br />
|-<br />
| [http://domotek.es/ DomoTek] || San Sebastián<br />
| || || || || || || &#x2713; || &#x2713; ||<br />
| ||<br />
|-<br />
| [https://www.DIYania.com/ DIYania] || Sevilla<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| En pedidos nacionales superiores a 50€ el envío es gratuito.<br />
|-<br />
| [https://www.en3dstudios.com/ en3DStudios] || Barcelona<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| Distribuidor Oficial Europa CR-10 (Creation Reality) <br />
|-<br />
| [http://www.fffworld.com/ FFF World] || Álava<br />
| || || || || || || &#x2713; || ||<br />
| ||<br />
|-<br />
| [http://www.filament2print.com/ Filament2print] || A Coruña<br />
| &#x2713; || || || || || || &#x2713; || || &#x2713;<br />
| ||<br />
|-<br />
| [http://gades3d.es/tienda/ Gades3D] || Cádiz<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713;<br />
| ||<br />
|-<br />
| [https://garagedays3d.com/es/ Garage Days 3D] || Súria<br />
| || &#x2713; || &#x2713; || &#x2713; || || &#x2713; || &#x2713; || &#x2713; || <br />
| ||<br />
|-<br />
| [http://www.iberobotics.com/shop/index.php?cPath=94 IBEROBOTICS Shop] || Santander<br />
| &#x2713; || || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| ||<br />
|-<br />
| [http://ifusionshop.com/ iFusionShop] || Tarragona<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||<br />
| ||<br />
|-<br />
| [http://impresoras3dlowcost.com/ Impresoras3DLowCost.com] || Córdoba<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| ||<br />
|-<br />
| [http://onlineshop.iniciativas3d.com/Iniciativas3D Iniciativas3D] || Córdoba y Málaga<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||<br />
| ||<br />
|-<br />
| [http://www.kitprinter3d.com/ KitPrinter3D ] || Madrid<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| ||<br />
|-<br />
| [http://www.lemonstore.es/ LemonStore] || Murcia<br />
| &#x2713; || || || || || || &#x2713; || ||<br />
| ||<br />
|-<br />
| [http://malagamakers.es/ MalagaMakers] || Málaga<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||&#x2713;<br />
| ||<br />
|-<br />
| [http://makergal.es/ MakerGal] || Santiago de Compostela<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||&#x2713;<br />
| [[Mendel Max XL]] ||<br />
|-<br />
| [https://moebyus.com/ Moebyus Machines] || Madrid<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||&#x2713;<br />
| [SIRIUS], One, Melta XL, M3, Amigo || También tienda física <br />
|-<br />
| [http://mprime.io/ M Prime] || Madrid<br />
| || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || || || <br />
| [http://mprime.io/es/m-prime-one M Prime One]||<br />
|-<br />
| [http://orballoprinting.com/ Orballo Printing] || Vigo<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || || <br />
| || <br />
|-<br />
| [http://plasticdreams.es/shop Plastic Dreams] || Murcia<br />
| &#x2713; || &#x2713; || &#x2713; || || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || [http://plasticdreams.es/producto/kit-p3steel-extension-200x300/ Extensión eje Y para P3Steel] ||<br />
|-<br />
| [https://www.impresora3d.es/ Printed Dreams] || Madrid/Cartagena<br />
| &#x2713; || || || || || || &#x2713; || &#x2713; || &#x2713;<br />
| ||<br />
|-<br />
| [http://presolid.com/es/ PRESolid Tech] || Barcelona<br />
| &#x2713; || || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || || &#x2713;<br />
| [http://presolid.com/es/content/category/2-productos ResinCAT] ||<br />
|-<br />
| [http://www.staticboards.es/productos/ StaticBoards] || A Coruña<br />
| || || &#x2713; || || || || || ||<br />
| [http://www.staticboards.es/productos/ramps14sb/ RAMPS 1.4SB] ||<br />
|-<br />
| [http://store.thingibox.com/ ThingiBOX] || Barcelona<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713;<br />
| [http://store.thingibox.com/es/22-ion-v6 ION V6 y V6 XL] || Envíos a todo el mundo<br />
|}<br />
<br />
=== ENLACES EN CUARENTENA ===<br />
(dan error de carga - se eliminarán a los 60 dias)<br />
<br />
{| class="wikitable sortable"<br />
|- style="background-color:#f0f0f0;"<br />
! style="vertical-align: bottom;" | Tienda<br />
! style="vertical-align: bottom;" | Localización<br />
! {{Vertical|2em|16em|&nbsp;Kits&nbsp;completos}}<br />
! {{Vertical|2em|16em|&nbsp;Piezas&nbsp;impresas}}<br />
! {{Vertical|2em|16em|&nbsp;Electrónica}}<br />
! {{Vertical|2em|16em|&nbsp;Motores}}<br />
! {{Vertical|2em|16em|&nbsp;Fusores&nbsp;y&nbsp;extrusores}}<br />
! {{Vertical|2em|16em|&nbsp;Rodamientos,&nbsp;varillas,&nbsp;correas, &nbsp;poleas&nbsp;y&nbsp;mecánica&nbsp;en&nbsp;general}}<br />
! {{Vertical|2em|16em|&nbsp;Consumibles}}<br />
! {{Vertical|2em|16em|&nbsp;Servicio&nbsp;de&nbsp;impresión &nbsp;y&nbsp;prototipado}}<br />
! {{Vertical|2em|16em|&nbsp;Cursos&nbsp;y&nbsp;talleres}}<br />
! style="vertical-align: bottom;" | Desarrolladores de...<br />
! style="vertical-align: bottom;" class="unsortable" | FECHA ERROR<br />
|-<br />
| [http://madrid3dprint.com/ madrid3DPrint] || Madrid<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || ||<br />
| || 20/5/17<br />
|-<br />
| [http://www.nativa3d.com Nativa3D] || Cádiz<br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713;<br />
| || 20/5/17<br />
|-<br />
| [http://shop.reclone3d.com/ Reclone3D] || Málaga<br />
| || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; || &#x2713; ||<br />
| [[J Head Hispania]] || 20/5/17<br />
|}<br />
<br />
<br />
<br />
=== On-line (Resto del Mundo) ===<br />
<br />
Europa:<br />
* [http://www.mendel-parts.com/ Mendel parts] (Holanda)<br />
* [http://www.xyzprinters.com/ http://www.xyzprinters.com/] (Holanda)<br />
* [http://shop.arcol.hu/ arcol.hu] (Hungría) <br />
* [https://shop.grrf.de/ German RepRap fundation] (Alemania)<br />
* [http://reprapsource.com/ reprapsource.com]<br />
* [http://reprapworld.com/ Reprap world] (Holanda) [filamento]<br />
* [https://0xfb.com/shop.html Future Bits] La tienda de Kliment! (Alemania)<br />
* [http://www.hotends.com/ hotends]<br />
* [http://www.orbi-tech.de/index_english.htm Orbi-tech]. Plástico (Alemania)<br />
* [http://reprap-3d-printer.com/ Reprap-3D-printer] (Francia)<br />
<br />
EEUU / América (ojo aduanas)<br />
* [http://www.makergear.com/ Makergear] (EEUU)<br />
* [http://www.lulzbot.com/en/ Lulzbot] (EEUU)<br />
* [http://gala-automation.com/ Gala automation] (EEUU)<br />
* [http://techpaladin.com/ techpaladin] (EEUU)<br />
* [http://www.centralreprap.com/prestashop/ CentralReprap]<br />
* [http://ultimachine.com/ Ultimachine] (EEUU)<br />
* [http://www.makermex.com/ MakerMex] (México)<br />
* [http://www.3dm.mx/ 3DM] (México) Impresoras 3D RepRap al Mejor Precio de México. Entrega Inmediata, consumibles y componentes.<br />
* [http://www.impresoras3dprusai3.com.mx/ Impresoras 3D en México] (CIUDAD DE MEXICO) D.F. Kit Prusa i3 Steel con marco en acero estructural, varillas acero inoxidable.<br />
* [massieu11@gmail.com] (CIUDAD DE MEXICO) sur del D.F. massieu11@gmail.com Componentes para armar tu impresora 3D excelente atención y servicio, banda, poleas, arduino,rodamientos, bujes de bronce, varilla lisa rectificada, banda cerrada/abierta, motores, hotend, cama caliente, kapton, ramps, LCD etc.<br />
<br />
Otros <br />
* [http://www.3dacessorieshub.com/ 3D Acessories Hub ].Una ventanilla única para todos los componentes de RepRap y las impresoras 3D<br />
* [http://www.goodluckbuy.com/ http://www.goodluckbuy.com/]. Tienda en china donde venden motores, varillas roscadas...<br />
* [http://www.futurlec.com/ Futurlec] Electrónica en general<br />
* [http://www.taydaelectronics.com/ Tayda Electronics] Electrónica en general<br />
* [http://www.dealextreme.com/ Dealextreme] Tienda china con prácticamente cualquier cosa. (contrasta precios antes de comprar)<br />
* [http://www.bitsbox.co.uk/ BitsBox] Componentes electrónicos, algunos especialmente baratos. Envía por ~3€<br />
* [http://www.emakershop.com/ eMAKERshop] Tienda online que vende productos de varios vendedores externos, como un portal de venta.<br />
* [http://www.zappautomation.co.uk/index.php?language=ES Zappautomation] Tienda con todo tipo de productos para CNCs (UK)<br />
* [http://makemendel.com/ Makemendel]<br />
* [http://www.ebay.com/itm/1pc-200mm-X-100ft-High-Temperature-Resistant-Kapton-Tape-/170864710486?ssPageName=ADME:L:OU:ES:3160 Kapton en eBay]: Cinta kapton de 20cm de ancho<br />
* [http://www.reprap.cc/ Reprap Austria] Tienda de todo tipo de material para Reprap tambien en ebay: [http://www.ebay.es/sch/reprapper/m.html?_nkw=&_armrs=1&_from=&_ipg=&_trksid=p3686 reprapper]<br />
<br />
<br />
<br />
=== Otros enlaces de Interés ===<br />
<br />
<br />
* [http://www.copsula.es/ '''Copsula'''] (Chiclana - Cádiz) Centro multidisciplinar de referencia para makers, artistas, musicos y diversos gremios. Punto de recogida y taller de http://www.gades3d.es/ , impresoras 3D, consumibles, repuestos, Arduino, Raspberry-pi, Meriendas Makers, Cursos, Venta y reparacion de informatica (PC y MAC), Distribuidor Oficial BQ.<br />
* [http://www.madtek3d.com/ '''MADTEK3D''']Empresa de Córdoba dedicada a la venta de Impresoras 3D, componentes y consumibles. Filamento de alta calidad y precios bajos. ¡Ampliando catálogo!<br />
* [http://shop.menextech.com/index.php MENEXTECH] (España) Todo lo necesario para que construyas tu impresora y componentes informaticos.<br />
* [http://www.moebyus.com/ Moebyus Machines ](España) Envío en 24h. Impresoras, partes, consumibles, repuestos, etc. Impresión bajo demanda, modelado, cursos. Tienda física en Principe de Vergara 206, Madrid.<br />
* [http://www.plabs3d.com/ '''Plabs 3D'''] - Extenso catálogo de filamentos para impresora 3D - Máxima calidad - Donostia (Gipuzkoa)<br />
* [http://www.rationalstock.es/ Rational Stock] (España) Ferretería online. Variedad y buenos precios para tornillería. Permite comprar por unidades. Envío económico en 24-48 horas.<br />
* [http://www.repparts3d.com/ '''RepParts 3D'''] (España) ABS, PLA, Conductor, Termocrómico, LayWood, LayBrick, Glow in the Dark, Nylon, HIPS. Con la mas amplia gama de colores<br />
<br />
<br />
=== Tiendas Físicas ===<br />
<br />
* [[Clone_wars:_Tiendas_en_Andalucia|Andalucía]]<br />
* [[Clone_wars:_Tiendas_en_asturias|Asturias]]<br />
* [[Clone_wars:_Tiendas_en_barcelona|Barcelona]]<br />
* [[Clone_wars:_Tiendas_en_burgos|Burgos]]<br />
* [[Clone_wars:_Tiendas_en_Cantabria|Cantabria]]<br />
* [[Clone_wars:_Tiendas_en_castellon|Castellón]]<br />
* [[Clone_wars:_Tiendas_en_galicia|Galicia]]<br />
* [[Clone_wars:_Tiendas_en_leon|León]]<br />
* [[Clone_wars:_Tiendas_en_madrid|Madrid]]<br />
* [[Clone_wars:_Tiendas_en_navarra|Navarra]]<br />
* [[Clone_wars:_Tiendas_en_valencia|Valencia]]<br />
* [[Clone_wars:_Tiendas_en_zaragoza|Zaragoza]]<br />
[http://goo.gl/maps/Md32Y Mapa] de tiendas y talleres<br />
<br />
<br />
=== LISTA NEGRA DE TIENDAS ===<br />
<br />
Tiendas con las que hemos tenido malas experiencias:<br />
* [http://myworld.ebay.es/drumas09/ drumas09] (UK). Este vendedor no envía los pedidos. Pedro tuvo un problema con este vendedor.<br />
<br />
* [http://www.leon-3d.es/ LEÓN 3D]. Ha habido problemas de licencias CC con algunos productos de esta empresa. [https://groups.google.com/forum/#!topic/asrob-uc3m-impresoras-3d/CXieuC0XtD0 Más datos en este hilo].<br />
<br />
<br />
== Servicios de Corte ==<br />
<br />
'''Cortenfrio'''<br />
*Empresa de corte en frio ubicada en Zaragoza.<br />
*[http://cortenfrio.com/index.htm Cortenfrio]<br />
<br />
'''Nativa3D Technologies'''<br />
*Servicios de Corte en Láser, Agua y Plasma<br />
*[http://www.nativa3d.com/ Nativa3D Technologies]<br />
*Email: contacto@nativa3d.com<br />
*Teléfono: 615 01 00 92<br />
<br />
'''Laserebro'''<br />
*Son un grupo de empresas con muchas sedes, tienes una cerca de casa seguro :D mira en el mapa de localizacion, en su web, en el apartado: Grupo Láser Ebro.<br />
*[http://www.laserebro.com/frame1.htm Laserebro]<br />
<br />
'''Naivan'''<br />
*Empresa de corte por Laser y otros servicios en Vitoria.<br />
*[http://www.naivan.com/ Naivan]<br />
*Email para enviar los planos de corte: naivan@naivan.com (enviar en dxf o pdf acotado)<br />
*Teléfono:945 259 857<br />
<br />
'''HJL'''<br />
*Empresa de corte por Laser y otros servicios en Murcia.<br />
*[http://www.hjl.es/ HJL]<br />
*Teléfono:968 802 044<br />
<br />
'''ThingiBOX'''<br />
*Corte por Laser en Viladecans (Barcelona).<br />
*[http://www.thingibox.com/ ThingiBOX]<br />
*Teléfono: 93 590 39 39<br />
<br />
'''Acottado'''<br />
*Empresa de corte por laser ubicada en Leganés (Madrid).<br />
*[http://acottado.com/laser/ Acottado]<br />
<br />
<br />
<br />
{| class="wikitable"<br />
|-<br />
|<br />
[[File:Clone-Wars-logo.png|border|100px|link=Proyecto Clone Wars]]<br />
| [[Proyecto Clone Wars]]<br />
|}<br />
<br />
[[Category:Clone wars/es]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=RAMPS_1.4/es&diff=181306RAMPS 1.4/es2018-01-17T15:26:06Z<p>Merlucin: </p>
<hr />
<div>{{RAMPS}}<br />
<br />
{{Languages|RAMPS 1.4}}<br />
<br />
{{Development<br />
|image = RAMPS1-3 fin.JPG<br />
|status = Working<br />
|name = RAMPS 1.4<br />
|description = RepRap Arduino Mega Pololu Shield<br />
Arduino MEGA based modular RepRap electronics.<br />
|license = [[GPL]]<br />
|author = johnnyr<br />
|reprap = Pololu Electronics<br />
|categories = [[:Category:RAMPS|RAMPS]][[Category:RAMPS]]<br />
}}<br />
<br />
<br/><br />
<br />
= Resumen =<br />
<br />
En la RAMPS 1.4, las resistencias y condensadores son ahora de montaje en superficie para albergar más componentes pasivos. Esto le añade otro controlador, pero nos mantuvimos con los tamaños más grandes para hacerlo más cómodo. <br />
<br />
<gallery><br />
Image:RAMPS1-3 fin.JPG<br />
Image:Arduinomega1-4connectors.png<br />
Image:RAMPS1.4schematic.png<br />
Image:Ramps_v1.4_shield_bothsides.png<br />
</gallery><br />
<br />
= RAMPS 1.4 SB Premium =<br />
<br />
Existen muchas versiones de RAMPS 1.4, sobre todo fabricadas en China. Suelen tener MOSFETs de baja calidad, que se calientan demasiado tras horas de impresión. Además usan conectores de plástico barato que es fácil que se acabe derritiendo.<br />
<br />
En España se fabrica la [https://www.staticboards.es/productos/ramps14sb/ RAMPS 1.4 SB Premium] que intenta solucionar todo esto. Usa MOSFETs de marca, con poca resistencia interna, que no necesitan ventiladores para funcionar. Además los conectores molex soportan la corriente necesaria.<br />
<br />
= Consejo de Seguridad=<br />
<br />
<br />
[[image:Generation3Electronics-achtung.gif|thumb]]<br />
<br />
Una vez que usted conecte la electricidad en su RepRap - incluso a sólo 12 voltios - usted tiene que tomar las precauciones básicas y de sentido común para evitar incendios. Por si acaso esto no funciona, pruebe el detector de humo de su taller. ¿No consiguió ningún detector de humo? ¡Obtenga uno! <br />
<br />
<br clear="all"/><br />
<br />
= Ensamblaje =<br />
== Soldadura de componentes ==<br />
== Herramientas necesarias ==<br />
Usted debe tener:<br />
Soldadura de hierro, alambre de soldadura, pinzas buenas<br />
Usted realmente necesita:<br />
Fieltro de soldadura, ventosa para desoldar, flux<br />
Métodos opcionales a utilizar:<br />
Pasta de soldadura, placa caliente o un horno <br />
<br />
=== Ensamblaje del escudo o shield === <br />
[[Image: RAMPS1-3pasteapplied.JPG | thumb]]<br />
Soldar la RAMPS 1,4 incluye tanto soldadura de montaje superficial y soldadura de orificio pasante.<br />
<br />
El montaje en superficie se puede hacer de varias maneras. Dado que todos los componentes de SMT en esta placa están sobre grandes pistas o pad se puede soldar pin por pin muy fácil con equipos de soldadura normal. Comience por poner una pequeña cantidad de soldadura en un pad. Si tiene flux, cobra el pad soldado. Utilice las pinzas para sujetar el componente en la posición y el calor de la soldadura para girar el componente en su lugar (asegúrese de que la gota de soldadura fluye para asegurarse de no tener una soldadura en frío). Luego soldar el otro pad. También es común el uso de pasta de soldar, horno de reflow (necesidad de enlace), y [[HotplateReflowTechnique]]<br />
<br />
Suelde los componentes SMT primero. Después la PTH en la parte superior de la placa. Finalmente soldar los conectores macho en la base. <br />
<br />
==== C2 - 100nF condensador ====<br />
[[Image: RAMPS1-3 100nF.JPG | thumb]]<br />
Esto se puede colocar en cualquier orientación.<br />
<br clear="all"/><br />
==== LED1 - LED Verde ====<br />
[[Image: RAMPS1-3 GrLED.JPG | thumb]]<br />
Colóquelas con el extremo que tiene puntos verdes alejado de la marca + en la PCB.<br />
<br clear="all"/><br />
==== LED2, LED3, LED4 - Rojo LED ====<br />
[[Image: RAMPS1-3 redLEDs.JPG | thumb]]<br />
Colocarlos con el extremo que tiene puntos verdes alejado de la marca + en la PCB.<br />
<br clear="all"/><br />
==== R13, R14, R15 - 10 Ohm resistor ====<br />
[[Image: RAMPS1-3 10r.JPG | thumb]]<br />
Estos se pueden colocar en cualquier orientación.<br />
<br clear="all"/><br />
==== R12 - resistencia de 1K ====<br />
[[Image: RAMPS1-3 1k.JPG | thumb]]<br />
Estos se pueden colocar en cualquier orientación.<br />
<br clear="all"/><br />
==== R23, R24, R25 - 1.8K resistencia ====<br />
[[Image: RAMPS1-3 1-8k.JPG | thumb]]<br />
Estos están marcados con 1K en la PCB, pero estamos usando más grandes para dar cabida a voltajes más altos. Estos se pueden colocar en cualquier orientación.<br />
<br clear="all"/><br />
<br />
==== R1, R7, R11, R21, R22 - Resistencia de 4.7K ====<br />
[[Image: RAMPS1-3 4-7k.JPG | thumb]]<br />
Estas se pueden colocar en cualquier orientación.<br />
<br clear="all"/><br />
<br />
==== R16, R17, R18, R19, R20 - resistencia de 10K ====<br />
[[Image: RAMPS1-3 10k.JPG | thumb]]<br />
Estas se pueden colocar en cualquier orientación.<br />
<br clear="all"/><br />
==== R2 , R3, R4, R5, R6, R8, R9, R10 - resistencia de 100K ====<br />
[[Image: RAMPS1-3 100k.JPG | thumb]]<br />
Estas se pueden colocar en cualquier orientación.<br />
<br clear="all"/><br />
==== C1, C5, C8 - 10uF condensador ====<br />
[[Image: RAMPS1-3 10uF.JPG | thumb]]<br />
Estos deben ser colocados en la orientación correcta. La placa tiene la huella de los componentes impresos. Las esquinas redondeadas en la base del condensador debe estar alineada con la impresión del blanco en la PCB.<br />
<br clear="all"/><br />
<br />
==== C3, C4, C6, C7, C9, C10 - 100uF capacitor ====<br />
[[Image: RAMPS1-3 100uF.JPG | thumb]]<br />
Estos deben ser colocados en la orientación correcta. La placa tiene la huella de los componentes impresos. Las esquinas redondeadas en la base del condensador debe estar alineada con la impresión del blanco en la PCB.<br />
<br clear="all"/><br />
<br />
<br />
==== Soldadura por SMT Reflow ====<br />
[[Image: RAMPS1-3_placed.JPG | 200px | thumb]] [[Image: RAMPS1-3 smtSoldered.JPG | thumb]]<br />
Si usted está utilizando un horno o el método de la placa caliente, ahora es el momento de aplicar calor (añadir enlaces aquí). Si ha utilizado un soldador, es probable que ya haya soldado todos estos componentes.<br />
<br />
Asegúrese de inspeccionar la soldadura SMT en este punto, ya que será más difícil volver a trabajar después de que los conectores estén encima.<br />
<br clear="all"/><br />
<br />
==== Pins Superiores ====<br />
[[Image: RAMPS1-3 tpins.JPG | thumb]]<br />
Suelde 1 1x6, 1x4 6 y 7 2x3 conectores macho en la parte superior de la placa. La parte larga debe estar hacia arriba para albergar un conector. Suelde una patilla de cada uno para fijarlas en su lugar. Luego vuelva a calentar la unión y empuje el componente hasta que quede perfectamente situado. A continuación, usted tendrá que soldar el resto de las patillas. Va a quemarse si toca el otro lado de la clavija que está soldando.<br />
<br />
Si desea utilizar las salidas de pines extra, ahora es el momento de soldar en el resto de los conectores.<br />
<br clear="all"/><br />
<br />
==== Conectores para los driver ====<br />
[[Image: RAMPS1-3 DrSockets.JPG | thumb]]<br />
Coloque los conectores hembra para los dirver o controladores paso a paso en la parte superior de la placa. Puede utilizar los conectores de pin 1x8 y 1x6 para fijarlos directamente. Gire la placa y suelde estos pines.<br />
<br clear="all"/><br />
==== D1, D2 - Diodos ====<br />
[[Image: RAMPS1-3 DnF.JPG | thumb]]<br />
[[Image: D1D2.jpg | thumb | Dónde encontrar los diodos D1 y D2]]<br />
Estos deben ser colocados con la orientación correcta. La banda sobre el diodo debe estar colocada de la misma forma que marca la placa.<br />
<br />
Una vez soldado D2. D2, F1 y F2 se muestra instalado aquí.<br />
<br />
D1 sólo debe ser instalado en la entrada de 5A si es alimentado por 12V. Puede omitirse y el Arduino se alimentará por USB. Usted querrá tener instalado D1 si va a imprimir sin un PC. Para reiterar, D1 DEBE ser omitido si usted está alimentando la entrada de 5A por más de 12 V, o la fuente no es estable, de lo contrario puede dañar sus ramps.<br />
<br style="clear: both" /><br />
<br />
==== F1 - Fusible MFR500 ====<br />
Este es el fusible amarillo más pequeño. Este se puede colocar en cualquier orientación. Al soldar los fusibles lo mejor es usar un trozo de filamento de 3 mm o algo similar para mantener el revestimiento cerámico en los pines y que la soldadura se reparta a lo largo del agujero pasante.<br />
<br />
Puesto que los fusibles son las partes más altas, es más simple y más conveniente soldarlos al final. Desde este punto sueldelos pins inferiores, el interruptor de reinicio, los terminales, MOSFETs y luego los fusibles.<br />
<br />
==== F2 - MFR1100 Fusible ====<br />
Este es el fusible amarillo más grande. Este se puede colocar en cualquier orientación.<br />
<br clear="all"/><br />
==== Q1, Q2, Q3 - Mosfets ====<br />
[[Image: RAMPS1-3 mosfet.JPG | thumb]]<br />
Estos deben estar orientados como en la imagen. La parte alta del disipador metálico del MOSFET debe situarse en la misma posición que la indicada en la placa con una raya blanca.<br />
<br clear="all"/><br />
<br />
==== Terminal del Mosfet ====<br />
[[Image: RAMPS1-3 6pos.JPG | thumb | rampas estándar 1,4 Bloquear D8-10 Terminal]]<br />
[[Image: RAMPS1-4 6pos_alt.png | thumb | Alternativa Plug / Conectores Jack]]<br />
Estos deben estar orientados de forma que la entrada de cable esté orientada hacia el borde de la placa. Soldar una patilla en cada extremo y despues asegúrese de que el componente esta plano en la placa y suelde los pines centrales.<br />
<br clear="all"/><br />
<br />
==== Terminales de la fuente ====<br />
[[Image: RAMPS1-3 4pos.JPG | thumb]]<br />
Esto sólo puede ser orientado en una dirección.<br />
<br clear="all"/><br />
==== Pins de la base ==== <br />
[[Image: RAMPS1-3 bpins.JPG | thumb]]<br />
[[image: DSC 0148.JPG | thumb]]<br />
Coloquelos en la base de la placa a todo lo largo para conectarlos a la placa Arduino Mega. Usted puede colocarlos en la placa Arduino Mega para mantenerlos en su lugar mientras los suelda. No sobrecaliente los teminales mientras estén en el Arduino o puede dañar los conectores.<br />
<br clear="all"/><br />
<br />
==== Interruptor de reinicio ==== <br />
[[Image: RAMPS1-3 rst.JPG | thumb]]<br />
Esto sólo puede ser orientado en una dirección.<br />
<br clear="all"/><br />
==== Inspección ==== <br />
[[Image: RAMPS1-3 fin.JPG | 200px | thumb]]<br />
Inspeccione su trabajo. Limpie los puentes de soldadura y soldaduras sospechosas.<br />
<br />
=== Controlador o driver Paso a paso === <br />
# * Los jumpers deben instalarse en cada controlador paso a paso: <br />
<br />
jumper Yes/No step size<br />
1 2 3<br />
no no no full step<br />
yes no no half step<br />
no yes no 1/4 step<br />
yes yes no 1/8 step<br />
yes yes yes 1/16 step<br />
Por defecto ahora es 1/16 micro pasos (todos los jumpers instalados bajo los controladores)<br />
<br />
# Cortar los conectores macho de 8 pins de largo para que se ajusten a cada lado del controlador paso a paso.<br />
# Inserte los conectores macho en las tomas en la ramps<br />
# Coloque los controladores paso a paso en los conectores de los pines y de suelde. Sólo calentar cada pin durante unos pocos segundos para evitar daños en el conector.<br />
# * Pegue el disipador de calor (si se usa) a la parte superior del [[A4988]] / [[A4983]] chip usando el pad provisto de adhesivo de doble cara.<br />
<br />
=== Finales de carrera opticos === <br />
Las instrucciones de construcción de las placas Opto 2,1 se puede encontrar [http://reprap.org/wiki/OptoEndstop_2.1 # Build_It aquí en la página reprap opto], y también [http://reprapsource.com/oe-r1 aquí] para reprapsource.com.<br />
# * Cortar el cable conductor 26AWG 3 en 3 [[Image:. RAMPSendstopConnector.JPG | right | 100px | Cierre de final de carrera.]]<br />
# * Nota: es posible que desee esperar hasta que haya construido la máquina para cortar los cables a la longitud perfecta [[Image: RAMPSendstopConboard.JPG | right | 100px | Cierre de conexión final de carrera en la ramps.]]<br />
# # * Acoplar y soldar un conector hembra en los extremos de cada cable. (la soldadura no es necesaria con las herramientas adecuadas de crimpado)<br />
# * Utilizar un conector 1x3 2,54 mm.<br />
# * Conecta al menos los finales de carrera mínimos. <br />
{| border="1"<br />
| RAMPS End<br />
|<br />
|-<br />
| SIG (S)<br />
| White<br />
|-<br />
| GND (-)<br />
| Black<br />
|-<br />
| VCC (+)<br />
| Red<br />
|}<br />
{| border="1" <br />
| Endstop End<br />
|<br />
|-<br />
| VCC (+)<br />
| Red<br />
|-<br />
| SIG (S)<br />
| White<br />
|-<br />
| GND (-)<br />
| Black<br />
|}<br />
<br />
=== Finales de carrera mecánicos ===<br />
<br />
[[File:MechSwitches 2Wire.JPG|thumb]]<br />
El firmware recomendado proporcionará una configuración para utilizar finales de carrera mecánicos con sólo dos cables.<br />
<br />
Localice el área denominada "endstops" en la esquina superior derecha de la placa y para cada uno de los ejes X, Y, y Z habrá un par de conectores de 3 pins (la etiqueta debería estar por debajo de cada pin), haga lo siguiente:<br />
<br />
Conecte S (fila superior, etiquetada a la izquierda) en las RAMPS a NC en el interruptor.<br />
Conecte GND en las RAMPS a C en el interruptor.<br />
<br />
- Nota: El firmware más reciente, como Marlin parece usar NO como el pin por defecto en el interruptor. De lo contrario puede que tenga que invertir los finales de carrera en el firmware. Usted puede utilizar M119 para comprobar su estado de tope.<br />
<br />
[[File:Endstop_Makerbot.jpeg|thumb]]<br />
- Nota2: Finales de carrera MakerBot v1.2, dada la posible confusión a la hora de conectar estos finales de carrera se adjunta imagen aclaratoria. Las conexiones son:<br />
<br />
wire 1 = Sig --> Pin 1 en la Ramps<br />
<br />
wire 2 = COM --> Pin 2 en la Ramps<br />
<br />
wire 3 = no se usa<br />
<br />
wire 4 = Vcc --> Pin 3 en la Ramps<br />
<br />
Mas info:<br />
<br />
[http://www.thingiverse.com/thing:4971 Planos en Thingiverse]<br />
<br />
[http://reprap.org/wiki/Mechanical_endstop_v1.2 Wiki RepRap]<br />
<br />
[https://storage.googleapis.com/google-code-archive-downloads/v2/code.google.com/makerbot/makerbot-mechanical-endstop-1.2.zip Planos en Google Code de MakerBot]<br />
<br />
=== Ponga los conectores a los cables del motor ===<br />
<br />
#* Soldar un conector hembra en los extremos de cada cable.<br />
#* Los utilizados en nuestra REPRAP son del tipo utilizado para los servos en los proyectos de RC. Véase [[http://www.reprap.org/wiki/Stepper_Motors Motores paso a paso]] para obtener información sobre los motores.<br />
<br />
=== Cables del Termistor ===<br />
<br />
Utilice un zócalo hembra de 2 pins y aísle bien los cables para asegurar que no se hace ningún corto. Tenga en cuenta la elevada temperatura.<br />
#* Conecte los cables de modo que los dos lleguen a T0 para el HotEnd.<br />
# Conecte los cables de modo que los dos lleguen a T1 para la base caliente.<br />
#* Si cambia de firmware verifique el estado del termistor.<br />
<br />
=== Carril de Controlador o driver Pololu===<br />
<br />
[[image:PololuExample.JPG|thumb]]<br />
En esta sección se supone que está utilizando Pololu, pero hay otras opciones. <br />
Inserte dos conectores macho 1x8 en los conectores hembra de la RAMPS como si estuviese colocado el controlador. Asegúrese de que el lado largo es el que queda encajado en la base y el corto el que requiere la soldadura, al igual que la parte del chip es la que queda visible en la placa. Coloque la placa de modo que los rótulos de la base del controlador coinciden con los de la RAMPS. Recuerde colocar un disipador de calor sobre el chips. <br />
<br />
= Configuración final =<br />
== Comprobaciones ==<br />
<br />
Si cree que puede tener algún error en la conexión de la electrónica, puede instalar un solo controlador paso a paso durante la prueba inicial, poniendo en riesgo solo uno de esos controladores.<br />
<br />
El potenciómetro de los controladores paso a paso, regula el limite de corriente para los motores. Gire en sentido contrario a las agujas del reloj completamente y después 1/4 de vuelta en el sentido contrario. Tenga cuidado de no forzar los tornillos, son muy delicados. Usted tendrá que ajustar el limite de corriente después. Tenga en cuenta que desde la conexión el controlador entrega al motor la intensidad máxima, incluso cuando no se mueven, así que si nota que sus controladores se ponen caliente, es posible que desee bajar un poco la corriente. Es aconsejable poner disipadores de calor a los controladores.<br />
<br />
[http://reprap.org/mediawiki/index.php?title=Arduino_Mega_Pololu_Shield#Make_the_cables_up_for_the_opto_endstops Conectar los finales de carrera] mínimos para X, Y, Z.<br />
<br />
Conectar motores (No conecte o desconecte los motores mientras tenga tensión; Si las conexiones están sueltas, esto hará que el motor vibre o se mueva incorrectamente y posiblemente se estropee su controlador paso a paso).<br />
<br />
Es posible que desee utilizar este código para probar todos los componentes electrónicos antes de instalar cualquiera de los firmware sugeridos.<br />
<br />
Instalar el firmware (mas información arriba). El flasheo del firmware se puede hacer sin la alimentación de 12V conectada.<br />
<br />
=== Cableado ===<br />
<br />
Es relativamente fácil cablear las RAMPS. Solo hay que añadir la resistencia del extrusor a D10, el termistor a T0, y cablear los motores PaP y finales de carrera. Para los motores, de izquierda a derecha, el orden de los cables es rojo, azul, verde y negro, junto a los pins de los drivers o controladores. Cuando conecte los cables a los finales de carrera (si utiliza 3 finales de carrera, tiene que conectarlos al slots MIN (-) correspondiente a cada eje, asegúrese de que coincida con las etiquetas.<br />
<br />
[[Image:Rampswire14.svg|500px|]]<br />
<br />
Note that tesla & tonok firmware use d9 and sprinter and johnny/tonok use d10 for the extruder hot end.<br />
<br />
==== Advertencias ====<br />
<font color="red">Conectar incorrectamente o la inversión de +/- puede destruir sus equipos electrónicos y causar riesgo de incendio.<br />
<br />
La incorrecta inserción de los controladores paso a paso puede destruir sus equipos electrónicos y causar riesgo de incendio. Asegúrese de desconectar el USB y la fuente de alimentación al retirar o ajustar los controladores paso a paso. Siempre asegúrese de conectar los cables en la orientación adecuada y en el zócalo correcto.<br />
<br />
Los pins de los finales de carrera son C-NC-NO. Esto se hace para permitir un mayor ajuste a la base caliente.</font><br />
<br />
=== Conexión de la alimentación ===<br />
<br />
Conecte la fuente de alimentación de 12V en el shield RAMPS. <font color="red">Asegúrese de conectar correctamente el + / - ó de lo contrario puede destruir sus equipos electrónicos y causar riesgo de incendio</font>.<br />
<br />
El par de conectores inferiores marcados por 5A alimentan los controladores paso a paso y la resistencia de extrusión y / o ventilador (D9, D10). La fuente debe poder entregar 5A<br />
<br />
El par de conectores de alimentación de 11A alimenta la base caliente, u otra salida (D8). La fuente debe poder entregar como mínimo 11A.<br />
<br />
Si ambos carriles de alimentación están conectados a la misma fuente de alimentación debe tener una capacidad mínima de 16A.<br />
<br />
El conector cilíndrico, en el Arduino MEGA, no suministra energía para alimentar la RAMPS ni para los motores paso a paso, cama caliente, etc<br />
<br />
El conector de alimentación no puede ser obviamente etiquetados, mirando a la conexión de alimentación positiva es el de la izquierda y el negativo está a la derecha de la clavija.<br />
<br />
== Fuente de alimentación ==<br />
[[Image:D1D2.jpg|thumb|Donde encontrar el diodo D1 (Nota D2 se muestra a la izquierda]]<br />
<br />
La RAMPS tiene de sobra con la línea de 12 V de una [[http://www.reprap.org/wiki/PCPowerSupply Fuente de alimentación de PC]]. también puede utilizar una fuente de alimentación portátil de 12V. <font color="red">Asegúrese de que puede dar 5A o más</font>. Se necesitan 11A adicionales para la base caliente.<br />
<br />
Consulte Conexión a la alimentación en la parte superior.<br />
<br />
Los 3 pins al lado del botón de reinicio están destinados a conectarse, opcionalmente, a su fuente de alimentación [https://groups.google.com/forum/?fromgroups=#!topic/asrob-uc3m-impresoras-3d/B-mU4hfmA1M (Correo del grupo donde se comenta)]. En caso de utilizarlos, el pulsador PS_ON servira para apagar y encender la fuente. Muchos Firmwares soportan esta función bajo el comando M80 para activar la fuente de alimentación y M81 para apagarla. Este uso se reserva para fuentes de alimentación ATX y puede ser modificada en el firmware para soportar fuentes de 5V de alta potencia, como la de una Xbox.<br />
<br />
Sin D1 instalado, o cuando el 12Vin no está conectado, el Arduino obtiene su energía del USB. Si usted quiere que su equipo funcione sin el USB conectado tiene que soldar el diodo D1 o conectar VCC a su fuente de alimentación.<br />
<br />
El pin VCC puede ser conectado a la salida de 5Vsb de su ATX para alimentar de forma continua al Arduino, desde esta misma. Tendrá que asegurarse que D1 no está instalado o se producirá un corto. El Arduino no está diseñado para ser alimentado directamente en el riel de VCC y el adaptador de VIN al mismo tiempo.<br />
<br />
El pin de 5V de ese conector en las RAMPS sólo proporciona los 5V a los conectores de los servos auxiliares. Está diseñado para que pueda puentearlo al pin VCC y usar la fuente de alimentación de Arduino para suministra 5V para los servos adicionales sí esta alimentando por USB o 5V. Dado que no es una gran carga extra la que pueden suponer estos servos, se puede conectar directamente a la fuente de 5V, en caso que disponga de una. También puede dejar este pin desconectado si no tiene planes de utilizar servos extra.<br />
<br />
=== Voltaje de entrada máximo ===<br />
==== Fuente de alimentación sin diodo ====<br />
<br />
El diodo 1N4004 conecta la tensión de entrada de la RAMPS a ArduinoMEGA. Si su tarjeta no tiene este diodo soldado, con seguridad puede ser alimentada hasta por 35V. (La mayoría de controladores pueden trabajar hasta con 35V, asegurar la tensión máxima antes de alimentar)<br />
<br />
==== Fuente de alimentación con diodo ====<br />
<br />
Si su placa tiene un diodo 1N4004 soldado, no aplique más de 12 V a la misma. Originalmente ArduinoMega está preparado para una entrada de 12 V. Mientras Arduino Mega 2560 puede llegar hasta los 20 V, aunque no se recomienda.<br />
<br />
= Firmware y asignación de Pin =<br />
<br />
<font color="red">La RAMPS 1.4 utiliza la misma definición para los pines que la 1.3.</font><br />
<br />
Necesitará el software de Arduino en [http://www.arduino.cc/en/Main/Software http://www.arduino.cc/en/Main/Software] para cargar el firmware para Arduino Mega. Arduino Mega 2560 Rev3 requiere la versión 0023 del software.<br />
<br />
Sprinter y Marlin son los firmwars más populares y estables para RAMPS en 12/28/2012.<br />
<br />
Se puede descargar un firmaware preconfigurado en http://ultimachine.com/sites/default/files/UltiMachineRAMPS1-4Sprinter.zip. (Por ahora no me hago responsable de esta descarga, hasta nuevo aviso)<br />
<br />
Otros finales de carrera, distintas a los mecánicos, (opción predeterminada en ultimachine.com) necesitan pins establecidos en el firmware de la siguiente manera:<br />
# define OPTO_PULLUPS_INTERNAL 1 , que se añaden a configuration.h si no existe de forma predeterminada.<br />
<br />
Estos son los pins definidos para esta placa.<br />
<pre><br />
// For RAMPS 1.4<br />
#define X_STEP_PIN 54<br />
#define X_DIR_PIN 55<br />
#define X_ENABLE_PIN 38<br />
#define X_MIN_PIN 3<br />
#define X_MAX_PIN 2<br />
<br />
#define Y_STEP_PIN 60<br />
#define Y_DIR_PIN 61<br />
#define Y_ENABLE_PIN 56<br />
#define Y_MIN_PIN 14<br />
#define Y_MAX_PIN 15<br />
<br />
#define Z_STEP_PIN 46<br />
#define Z_DIR_PIN 48<br />
#define Z_ENABLE_PIN 62<br />
#define Z_MIN_PIN 18<br />
#define Z_MAX_PIN 19<br />
<br />
#define E_STEP_PIN 26<br />
#define E_DIR_PIN 28<br />
#define E_ENABLE_PIN 24<br />
<br />
#define SDPOWER -1<br />
#define SDSS 53<br />
#define LED_PIN 13<br />
<br />
#define FAN_PIN 9<br />
<br />
#define PS_ON_PIN 12<br />
#define KILL_PIN -1<br />
<br />
#define HEATER_0_PIN 10<br />
#define HEATER_1_PIN 8<br />
#define TEMP_0_PIN 13 // ANALOG NUMBERING<br />
#define TEMP_1_PIN 14 // ANALOG NUMBERING<br />
</pre><br />
<br />
==Fuente==<br />
<br />
{|class="wikitable" style="margin: 1em auto 1em auto;"<br />
|- style="background-color:#999999;" <br />
! FILE ID#<br />
! TYPE<br />
! DESCRIPTION<br />
! DOWNLOAD<br />
|-<br />
| [[File:ArduinoMegaPololuShield.zip]]<br />
| Eagle Files<br />
| These are the files you need to make the board.(Use the File: link to the left to access older versions of the file.)<br />
| [[media:ArduinoMegaPololuShield.zip]]<br />
|-<br />
|-<br />
| [[File:RepRapjr.lbr]]<br />
| Eagle Libraries<br />
| The components used in this board are here. see [[Eagle_Library]]<br />
| [[media:RepRapjr.lbr]]<br />
|-<br />
|}<br />
<br />
==Lista de materiales==<br />
{| border="1"<br />
|-<br />
! ID<br />
! Description<br />
! Quantity<br />
! Part Number<br />
! Reichelt Order Number<br />
! Digikey Part Number (Description) <br />
|-<br />
| U1<br />
| Arduino Mega<br />
| 1<br />
|2560 or 1280<br />
|<br />
|N/A<br />
|-<br />
| U2,U3,U4,U5<br />
| [[Pololu stepper driver board]]s<br />
| 4<br />
| A fifth one can be used for a 2nd extruder or extra axis<br />
|<br />
|N/A<br />
|-<br />
| C2<br />
| 100nF capacitor (0805)(> highest planned voltage)<br />
| 1<br />
| <br />
|<br />
|<br />
|-<br />
| C1,C5,C8<br />
| 10uF capacitor (153CLV-0405)(>5V)<br />
| 3<br />
| <br />
|<br />
|<br />
|-<br />
| C3,C4,C6,C7,C9,C10<br />
| 100uF capacitor (153CLV-0605)(> highest planned voltage)<br />
| 6<br />
|<br />
|<br />
|<br />
|-<br />
| R1,R7,R11,R21,R22<br />
| 4.7K resistor (0805)(1%)<br />
| 5<br />
| <br />
|<br />
|<br />
|-<br />
| R2,R3,R4,R5,R6,R8,R9,R10<br />
| 100K resistor (0805)<br />
| 8<br />
| <br />
|<br />
|<br />
|-<br />
| R12<br />
| 1K resistor (0805)<br />
| 1<br />
| <br />
|<br />
|<br />
|-<br />
| R23,R24,R26<br />
| 1.8K resistor (0805)<br />
| 3<br />
|<br />
|<br />
|<br />
|-<br />
| R16,R17,R18,R19,R20<br />
| 10K resistor (0805)<br />
| 5<br />
|<br />
|<br />
|<br />
|-<br />
| R13,R14,R15<br />
| 10 ohm resistor (0805)<br />
| 3<br />
|<br />
|<br />
|<br />
|-<br />
| Q1,Q2,Q3<br />
| N-channel Mosfet<br />
| 3<br />
| STP55NF06L<br />
| ZXM 64N035 L3<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=497-6742-5-ND 497-6742-5-ND] (MOSFET N-CH 60V 55A TO-220)<br />
|-<br />
| D1,D2<br />
| Diode<br />
| 2<br />
| 1N4004<br />
| 1N 4004<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=1N4004FSCT-ND 1N4004FSCT-ND] (DIODE GEN PURPOSE 400V 1A DO41)<br />
|-<br />
| F1<br />
| PTC resettable fuse (30V, Hold5A, Trip10A)<br />
| 1<br />
| MF-R500<br />
| PFRA 500<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=MF-R500-ND MF-R500-ND] (FUSE PTC RESETTABLE 5A HOLD)<br />
|-<br />
| F2<br />
| PTC resettable fuse (Hold11A)<br />
| 1<br />
| MF-R1100<br />
| <br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=RGEF1100-ND RGEF1100-ND] (POLYSWITCH RGE SERIES 11.0A HOLD)<br />
|-<br />
| J2<br />
| D8-D10 Outputs // 6 position screw terminal (min 11A per contact) OR Jack/Plug connector pair<br />
| 1<br />
| 282837-6<br />
| AKL 101-06<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=WM7857-ND WM7857-ND] (CONN TERMINAL BLOCK 6POS 5.08MM) <br/>Alternative: 1x [http://www.digikey.com/product-detail/en/20020109-H061A01LF/609-4284-ND/2509130 609-4284-ND] & 1x [http://www.digikey.com/scripts/DkSearch/dksus.dll?WT.z_header=search_go&lang=en&keywords=609-4218-ND&x=0&y=0&cur=USD 609-4218-ND]. [https://lh6.googleusercontent.com/--1nJttlNQDs/UNfmaLXKiTI/AAAAAAAADxQ/Z6CSD4V8r6I/s617/20121223_194819.jpg May prevent overtemp events]<br />
|-<br />
| LED1<br />
| Green LED (0805)<br />
| 1<br />
|<br />
|<br />
|<br />
|-<br />
|LED2,LED3,LED4<br />
| Red LED (0805)<br />
| 3<br />
|<br />
|<br />
|<br />
|-<br />
| S1<br />
| Push button switch<br />
| 1<br />
| B3F-3100 <br />
| TASTER 3305B (should fit footprint also, but button will overhang board edge)<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=450-1648-ND 450-1648-ND] (SWITCH TACT RA H=6.35MM)<br />
|-<br />
| X1<br />
| Power jack (Plug and fixed receptacle)(Min 11A per position more is better)<br />
| 1<br />
| MSTBA 2,5 and MSTBT 2,5 (5.04mm spacing 4 connector)<br />
| <br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=WM7847-ND WM7847-ND] (CONN HEADER 4POS 5.08MM R/A TIN) &amp; [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=WM7953-ND WM7953-ND] (CONN TERM BLOCK 4POS 5.08MM R/A)<br />
|-<br />
|<br />
| 2 x 3 pin header<br />
| 8<br />
| 961206-6404-AR<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=3M9459-ND 3M9459-ND] (CONN HEADER VERT DUAL 6POS GOLD)<br />
|-<br />
| <br />
| 4 pin header<br />
| 5<br />
| 961104-6404-AR<br />
| SL 1X36G 2,54 (3 of these)<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=3M9449-ND 3M9449-ND] (CONN HEADER VERT SGL 4POS GOLD)<br />
|-<br />
| <br />
| 6 pin header<br />
| 2 (? - from http://gala-automation.com/index.php/component/content/article/26-reprap-tutorials/42-ramps-14-bom)<br />
| 961106-6404-AR<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=3M9451-ND 3M9451-ND] (CONN HEADER VERT SGL 6POS GOLD)<br />
|-<br />
|<br />
| 2 x 18 Pin Stackable Female Header (non stackables can be used with plated through holes)<br />
| 1<br />
| <br />
| MALE: SL 2X25G 2,54 (2 of them, shortened with a saw or pliers)<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7121-ND S7121-ND] (CONN HEADER FMAL 36PS.1" DL GOLD) - Not Stackable<br />
|-<br />
| <br />
| 8 Pin Stackable Female Header (non stackables can be used with plated through holes)<br />
| 5<br />
|<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7041-ND S7041-ND] (CONN HEADER FEMALE 8POS .1" GOLD) - Not Stackable<br />
|-<br />
| <br />
| 6 Pin Stackable Female Header (non stackables can be used with plated through holes)<br />
| 1<br />
|<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7039-ND S7039-ND] (CONN HEADER FEMALE 6POS .1" GOLD) - Not Stackable<br />
|-<br />
| <br />
| 24 Pin Female Header * Note *<br />
| 2<br />
| Required to carry enough current for motors<br />
| <br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7057-ND S7057-ND] (CONN HEADER FMALE 24POS .1" GOLD) - Rated @ 3A / Pin<br />
|-<br />
| <br />
| 8 Pin Female Header * Note *<br />
| 4<br />
| Required to carry enough current for motors<br />
| <br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7041-ND S7041-ND] (CONN HEADER FEMALE 8POS .1" GOLD) - Rated @ 3A / Pin<br />
|-<br />
|<br />
| 0.1" Jumpers<br />
| 15<br />
|<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=A26242-ND A26242-ND] (SHUNT LP W/HANDLE 2 POS 30AU)<br />
|-<br />
|<br />
| Circuit Board<br />
|1<br />
|v1.4<br />
|<br />
|N/A<br />
|}<br />
Note * You can use Female Headers which are not the exact size, but they are hard to break/cut so in this case buy some extra! (one wasted header per cut)<br />
<br />
A BOM for sourcing the RAMPS components from Mouser is also available in [https://docs.google.com/spreadsheet/ccc?key=0Auf-66FPv0JidHhtRVB0VVplOURwWklrX0tIeXhsS3c&hl=en_US#gid=0 this google spreadsheet]<br />
<br />
Shopping lists for v1.4 [http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=d126a71257] .<br />
<br />
= Donde comprar =<br />
<br />
[http://store.thingibox.com/es/electricidad/38-ramps_14.html Completamente Ensamblada y disponible Ramps-FD] en Thingibox</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=RAMPS_1.4&diff=181305RAMPS 1.42018-01-17T15:18:44Z<p>Merlucin: /* Where to buy RAMPS 1.4.2 */</p>
<hr />
<div>{{RAMPS}}<br />
<br />
{{Languages|RAMPS 1.4}}<br />
<br />
{{Development<br />
|image = RAMPS1-3 fin.JPG<br />
|status = Working<br />
|name = RAMPS 1.4<br />
|description = RepRap Arduino Mega Pololu Shield<br />
Arduino MEGA based modular RepRap electronics.<br />
|license = [[GPL]]<br />
|author = johnnyr<br />
|reprap = Pololu Electronics<br />
|categories = {{tag|RAMPS}} {{tag|8/16-bit board}}<br />
}}<br />
<br />
<br/><br />
<br />
=Summary=<br />
<br />
In RAMPS 1.4, the resistors and capacitors are now surface mount to fit more passive components. This does add another set of steps to assembly, but we stuck with larger sizes to make it fairly painless.<br />
<br />
<gallery><br />
Image:RAMPS1-3 fin.JPG<br />
Image:Arduinomega1-4connectors.png<br />
Image:RAMPS1.4schematic.png<br />
Image:Ramps_v1.4_shield_bothsides.png<br />
</gallery><br />
<br />
Reference board orientation is component side up, power inputs to the left.<br />
<br />
= Safety Tip =<br />
<br />
[[image:Generation3Electronics-achtung.gif|left]]<br />
<br />
Once you start putting electricity into your RepRap - even at just 12 volts - you have to take basic, common sense precautions to avoid fires. Just in case these fail, test your workshop [http://en.wikipedia.org/wiki/Smoke_detector smoke detector]. Got no smoke detector? Get one!<br />
<br />
<br clear="all"/><br />
<br />
= '''WARNING''' - THERMAL-isolation-related DESIGN FLAW IN Power handling capacity of '''PRODUCTION''' RAMPS 1.4 boards =<br />
<br />
A "thermals" design flaw has been noted in the RAMPS 1.4 Eagle CAD files. This has been confirmed by visual inspection of production boards, which consistently shows only between two and three (almost never four) thermal-isolating traces per side of the PCB, to power-carrying pins, of under a 0.5 amp carrying-capacity per trace, assuming a 1oz copper thickness.<br />
<br />
[[image:RAMPS_1_4_THERMAL_DESIGN_FLAW.jpg|600px]]<br />
<br />
The problem may be fixed in the Eagle CAD files - for a future version of RAMPS ''only'' - by disabling "thermals" on the GND, +12V and the +12V2 Copper pour. However on existing (mass-produced) RAMPS 1.4 boards, estimating the total widths (including all thermals from all tracks on both sides of the PCB) checking with an online copper width calculator and adding up the total current, assuming a 1oz copper PCB the maximum safe current on the fuses (giving only a 10C rise in temperature of the thermal-isolation tracks) is only around 6 (six) amps and in other areas the maximum safe current (assuming the same 10C rise in temperature) is around 8 (eight) amps.<br />
<br />
This problem may potentially be fixed on existing RAMPS 1.4 boards by augmenting the power traces with suitably-thick insulated wires with sufficient current-carrying capacity, soldering them to '''all''' the relevant pins.<br />
<br />
A video with a full walkthrough including calculating the total track width and inputting it into a trace width current calculator is here:<br />
https://youtu.be/4Ff_XG1OPIM<br />
<br />
<br clear="all"/><br />
<br />
=Assembly=<br />
==Component Soldering==<br />
==Required Tools==<br />
You must have:<br />
Solder iron, solder wire, good tweezers<br />
You really need:<br />
Solder wick, solder sucker, flux pen<br />
Optional methods use:<br />
Solder paste, hot plate or oven <br />
<br />
===Shield Assembly===<br />
[[Image:RAMPS1-3pasteapplied.JPG|thumb]] <br />
Soldering RAMPS 1.4 includes both surface mount and through hole soldering.<br />
<br />
The surface mount can be done a few ways. Since all the SMT components on this board are large 2 pad parts you can do pin by pin soldering pretty easy with normal soldering equipment. Start by putting a small amount of solder on one pad. If you have flux, coat the soldered pad. Use the tweezers to hold the component down in position and heat the solder to tack the component into place (make sure the entire solder blob flows so you don't get a cold solder). Then solder the other pad. Also popular is using solder paste for pad by pad soldering, Oven Reflow (need link), and [[HotplateReflowTechnique]]<br />
<br />
Solder the SMT components first. Then the PTH on top of the board. Finally solder the pin headers on the bottom.<br />
<br />
==== C2 - 100nF capacitor====<br />
[[Image:RAMPS1-3 100nF.JPG|thumb]]<br />
This can be placed in any orientation.<br />
<br clear="all"/><br />
==== LED1 - Green LED====<br />
[[Image:RAMPS1-3 GrLED.JPG |thumb]]<br />
Place these with the end having green dots away from the + mark on the PCB.<br />
<br clear="all"/><br />
<br />
==== LED2, LED3, LED4 - Red LED====<br />
[[Image:RAMPS1-3 redLEDs.JPG |thumb]]<br />
Place these with the end having green dots away from the + mark on the PCB.<br />
<br clear="all"/><br />
====R13, R14, R15 - 10 Ohm resistor====<br />
[[Image:RAMPS1-3 10r.JPG|thumb]]<br />
These can be placed in any orientation.<br />
<br clear="all"/><br />
====R12 - 1K resistor====<br />
[[Image:RAMPS1-3 1k.JPG |thumb]]<br />
These can be placed in any orientation.<br />
<br clear="all"/><br />
====R23, R24, R25 - 1.8K resistor====<br />
[[Image:RAMPS1-3 1-8k.JPG |thumb]]<br />
These are marked 1K on the PCB, but we are using larger ones to accommodate higher voltages. These can be placed in any orientation.<br />
<br clear="all"/><br />
<br />
====R1, R7, R11, R21, R22 - 4.7K resistor====<br />
[[Image:RAMPS1-3 4-7k.JPG|thumb]]<br />
These can be placed in any orientation.<br />
<br clear="all"/><br />
====R16, R17, R18, R19, R20 - 10K resistor====<br />
[[Image:RAMPS1-3 10k.JPG|thumb]]<br />
These can be placed in any orientation.<br />
<br clear="all"/><br />
====R2, R3, R4, R5, R6, R8, R9, R10 - 100K resistor====<br />
[[Image:RAMPS1-3 100k.JPG |thumb]]<br />
These can be placed in any orientation.<br />
<br clear="all"/><br />
====C1, C5, C8 - 10uF capacitor====<br />
[[Image:RAMPS1-3 10uF.JPG|thumb]]<br />
These must be placed in the proper orientation. The board has the foot print of the components printed on it. The rounded corners on the base of the capacitor must line up with the white print on the PCB.<br />
<br clear="all"/><br />
<br />
====C3, C4, C6, C7, C9, C10 - 100uF capacitor====<br />
[[Image:RAMPS1-3 100uF.JPG|thumb]]<br />
These must be placed in the proper orientation. The board has the foot print of the components printed on it. The rounded corners on the base of the capacitor must line up with the white print on the PCB. <br />
<br clear="all"/><br />
<br />
====Reflow SMT soldering====<br />
[[Image:RAMPS1-3_placed.JPG|200px|thumb]] [[Image:RAMPS1-3 smtSoldered.JPG|thumb]]<br />
If you are doing oven or hot plate method, now is the time apply heat (add links here). If you used a solder iron, you have probably already soldered all these components.<br />
<br />
Make sure to inspect the SMT soldering at this point since it will be harder to rework after the headers are on top.<br />
<br clear="all"/><br />
====Top pins====<br />
[[Image:RAMPS1-3 tpins.JPG|thumb]]<br />
Solder 1 1x6, 6 1x4, and 7 2x3 pin headers on top of the board. The long post should be standing up to take a connector. Solder one leg on each one to tack them into place. Then re-heat the joint and push on the component until it is perfectly situated. Then you'll want to solder the rest of the leads. You will get burnt if you touch the other side of the pin you are soldering.<br />
<br />
If you want to use the extra pin outputs, now is the time to solder on the rest of the headers.<br />
<br clear="all"/><br />
<br />
====Driver sockets====<br />
[[Image:RAMPS1-3 DrSockets.JPG |thumb]]<br />
Place the female headers for the stepper drivers on top of the board. You can use the 1x8 and 1x6 pin headers to jig them straight. Turn the board over and solder these pins.<br />
<br clear="all"/><br />
====D1, D2 - Diodes====<br />
[[Image:RAMPS1-3 DnF.JPG|thumb]]<br />
[[Image:D1D2.jpg|thumb|Where to find the D1 and D2 diodes]]<br />
These must be placed in the proper orientation. The band on the diode must be turned the same way as the mark on the board.<br />
<br />
Definitely solder D2 in. D2, F1, and F2 are shown installed here.<br />
<br />
D1 should only be installed if the 5A rail is powered by 12V. It can be omitted and the Arduino will be powered from USB. You will want D1 installed if you add components to print without a PC. To reiterate, D1 MUST be omitted if you are powering the 5A rail by more than 12V, or the power is not absolutely clean, otherwise you may damage your ramps.<br />
<br style="clear: both" /><br />
<br />
====F1 - MFR500 Fuse====<br />
This is the smaller yellow fuse. This can be placed in any orientation. When soldering the fuses it is best to use a piece of 3mm filament or something similar to keep the ceramic coating on the pins from blocking proper solder along the through hole.<br />
<br />
Since the fuses are the tallest parts, it is simpler and more convenient to solder them last. From this point on, solder the rest of the RAMPS in order of bottom pins, reset switch, terminals, mosfets and then fuses.<br />
<br />
====Bottom pins====<br />
[[Image:RAMPS1-3 bpins.JPG|thumb]]<br />
[[image:DSC 0148.JPG|thumb]]<br />
Place these on the bottom of the board with the long post out to plug into the Arduino MEGA. You can plug them into the MEGA to hold them in place while you solder. Do not overheat the pins while in Arduino or you may damage its connectors.<br />
<br clear="all"/><br />
<br />
====Reset switch====<br />
[[Image:RAMPS1-3 rst.JPG|thumb]]<br />
This can only be oriented in one direction.<br />
<br clear="all"/><br />
====Mosfet Terminal====<br />
[[Image:RAMPS1-3 6pos.JPG |thumb|Standard RAMPS 1.4 D8-10 Terminal Block]]<br />
[[Image:RAMPS1-4 6pos_alt.png |thumb|Alternative Plug/Jack Connectors]]<br />
This must be oriented where the wire holes are turned towards the edge of the board. Solder a pin on each end and make sure the component is flat on the board and solder the middle pins.<br />
<br clear="all"/><br />
====Power Terminal====<br />
[[Image:RAMPS1-3 4pos.JPG|thumb]]<br />
This can only be oriented in one direction.<br />
<br clear="all"/><br />
====Q1, Q2, Q3 - Mosfets====<br />
[[Image:RAMPS1-3 mosfet.JPG|thumb]]<br />
These must be orientated as in the picture. The tall heat sink part of the mosfet needs to be turned the same as the mark on the board.<br />
<br clear="all"/><br />
====F2 - MFR1100 Fuse====<br />
This is the larger yellow fuse. This can be placed in any orientation.<br />
<br clear="all"/><br />
<br />
====Inspection====<br />
[[Image:RAMPS1-3 fin.JPG|200px|thumb]]<br />
Inspect your work. Clean any solder bridges and suspect solders.<br />
<br />
===Stepper Driver Boards===<br />
#*Jumpers need to be installed under each stepper driver:<br />
<br />
jumper Yes/No step size<br />
1 2 3<br />
no no no full step<br />
yes no no half step<br />
no yes no 1/4 step<br />
yes yes no 1/8 step<br />
no no yes 1/16 step<br />
yes no yes 1/32 step<br />
no yes yes 1/64 step<br />
yes yes yes 1/128 step<br />
<br />
If the jumpers set it to a higher number of micro steps than supported by the driver it will operate at the maximum number of micro steps for that driver.<br />
For now the default is maximum micro stepping (all jumpers installed under drivers), which results in 1/16 micro stepping for A4988 drivers and 1/32 for DRV8825. Although for efficiency and accuracy you should opt for the biggest steps that will yield sufficient resolution. Eg. you don't need 5000 steps per millimeter and [http://www.micromo.com/microstepping-myths-and-realities micro-steps] less than 1/16 have reduced torque per step, reduced accuracy and higher driver load].<br />
<br />
Note: This can vary for different drivers.<br />
<br />
#Cut the pin headers to 8 pins long so that they fit each side of the stepper driver.<br />
#Insert the pin headers into the sockets on RAMPS<br />
#Fit the stepper drivers onto the pin headers and solder. Only heat each pin for a few seconds at time to avoid damage to the socket. <br />
#*Glue the heatsink (if used) to the top of the [[A4988]]/[[A4983]] chip using the provided pad of double-sided adhesive.<br />
<br />
===Opto Endstops===<br />
Opto endstop build instructions can be found at [[Gen7_Endstop_1.3.1]], and also [http://reprapsource.com/oe-r1 here] for reprapsource.com's instructions.<br />
#* Cut the 26awg 3 conductor cable into 3 length.[[Image:RAMPSendstopConnector.JPG|right|200px|Close up of endstop connector on endstop.]]<br />
#* Note: you may want to wait until you've built your machine to cut the cables to the perfect length.[[Image:RAMPSendstopConboard.JPG|right|200px|Close up of endstop connection on RAMPS]]<br />
##* crimp and solder a female connector to the ends of each wire. (solder not necessary with proper crimp tools) <br />
#* use the 2.54mm 1x3 housing.<br />
#* Connect at least the minimum endstops. <br />
{| border="1"<br />
| RAMPS End<br />
|-<br />
| SIG (S)<br />
| White<br />
| Top pin<br />
|-<br />
| GND (-)<br />
| Black<br />
| Center pin<br />
|-<br />
| VCC (+)<br />
| Red<br />
| Lower pin<br />
|}<br />
{| border="1" <br />
| Endstop End<br />
|<br />
|-<br />
| VCC (+)<br />
| Red<br />
|-<br />
| SIG (S)<br />
| White<br />
|-<br />
| GND (-)<br />
| Black<br />
|}<br />
<br />
===Mechanical Endstops===<br />
[[File:MechSwitches 2Wire.JPG|thumb]]<br />
The recommended firmware will provide a configuration to use mechanical endstops with just two wires. <br />
<br />
Find the area labelled "endstops" in the upper right corner of the board and for each of the X, Y, and Z pairs of pins (label should be below each set) do the following: <br />
# Connect S (top row, labelled to the left) on RAMPS to NC on the switch.<br />
# Connect GND on RAMPS to C on the switch.<br />
<br />
'''Note:''' The latest firmware such as Marlin seems to use NO as the default pin on the switch. Otherwise you may need to invert the endstops in the firmware. You can use M119 to check your endstops status.<br />
<br />
===Put the connectors on the motor wires===<br />
#* solder a female connector to the ends of each wire.<br />
#* use the 2.54mm 1x3 housing. <br />
#* Shown is the type used for servos in RC projects. See [[Stepper Motors]] for info on motors.<br />
<br />
===Thermistor Wires===<br />
Use a 2 pin 0.1" connector to terminate the thermistor wires.<br />
#* Connect the cable so the 2 wires go to T0<br />
#Connect the 2 heater wires to D10 (E0H on older boards) and the + connection above it.<br />
#* If changing to an unverified firmware it is best to verify heater circuit function with a meter before connecting heater to prevent damage to the extruder.<br />
<br />
===Pololu carriage===<br />
[[image:PololuExample.JPG|thumb]]<br />
This section assumes you are using Pololu, but there are other options. Insert two 1x8 pin headers into the board. If you bought a kit with one 16 pin header, simply cut it so that you have two 1x8. Make sure that the side with the labels has the long ends of the posts, and the side you want to solder is the side with the heat sink. Doing this backwards will cause you not to see the labels and will most likely not fit. Remember to apply a heat-sink to the largest chip on the back.<br />
<br />
Insert the motor boards with the potentiometer to the right side (furthest from the power connectors).<br />
<br />
=Final Setup=<br />
==Pre-Flight Check==<br />
If you think you may have mistakes you can install only one stepper driver during initial testing and risk only one stepper driver.<br />
<br />
The trimpot on the stepper drivers controls the current limit. Turn it all the way down (counter clock wise) and back up 25%. Be careful to not force the trimpot, it is delicate. You will need to fine tune the current limit later. Note that it is allways giving the motors that much power, even when not moving, so if your stepper motor drivers are getting hot, you may want to turn it down slightly.<br />
<br />
[http://reprap.org/mediawiki/index.php?title=Arduino_Mega_Pololu_Shield#Make_the_cables_up_for_the_opto_endstops Connect the minimum endstops] for X,Y, and Z<br />
<br />
Connect Motors (Do not disconnect or connect motors while powered; if the connection is loose, this will cause the motors to misbehave and possibly kill your stepper driver.)<br />
<br />
You may want to use this [http://reprap.org/wiki/File:RAMPSTestCode.pde code] to test all the electronics before installing any of the suggested firmwares.<br />
<br />
Install firmware (More info below). Firmware flashing can be done without 12V power supply connected.<br />
<br />
==Wiring==<br />
It is relatively simple to wire up the RAMPS. Just add the extruder heating coil wire to D10, the thermistor to the two T0 pins on middle right right, and wire up the steppers and endstops. From left to right, wire all of the stepper motor's wires as red, blue, green, and black or red, green, yellow, blue into the pins next to the Pololus. When you connect the wires to the endstops (if you are using 3 endstops, plug them into the MIN (-) slots), make sure you match the labels. <br />
<br />
[[Image:Rampswire14.svg|500px|]]<br />
<br />
Note that Tesla & Tonok firmware use D9 and Sprinter, Marlin, and Johnny/Tonok use D10 for the extruder hot end.<br />
<br />
===Warnings===<br />
<br />
<font color="red">Reversing +/- or otherwise incorrectly connecting power can destroy your electronics and cause fire hazard.<br />
<br />
Incorrectly inserting stepper drivers will destroy your electronics and cause a fire risk. Always make sure power and USB is disconnected when removing or adjusting stepper drivers. Always make sure to insert drivers in correct orientation and in the socket correctly.<br />
<br />
The endstop pins are Signal - GND - VCC, instead of the VCC - Sig - GND like the rest of RepRaps boards. Make sure to wire them correctly. This is done to allow squeezing fatter traces on the printable board.<br />
<br />
DON'T secure Arduino/RAMPS with conductive screws through both mounting holes. The screw may cut into the positive trace creating a HIGH current short.</font><br />
<br />
==Connecting Power==<br />
<br />
Connect your 12V power supply to the RAMPS shield. <font color="red">Reversing +/- or otherwise incorrectly connecting power can destroy your electronics and cause fire hazard</font>.<br />
<br />
The bottom pair of connectors marked 5A power the stepper drivers and Extruder heater/fan (D9, D10). The source should be rated a minimum of 5A.<br />
<br />
The pair of connectors above marked 11A power a Heated Bed, or other output (D8). The source should be rated a minimum 11A (if both power rails are connected to the same supply it should have a minimum rating of 16A).<br />
<br />
The barrel connector, on the Arduino MEGA, will NOT power RAMPS and will not provide power to the stepper motors, heated bed, etc.<br />
<br />
The power connector plug may not be obviously labeled, looking at the power connection the positive is on the left and the negative is on the right of the plug.<br />
<br />
==Power Supply==<br />
[[Image:D1D2.jpg|thumb|Where to find the D1 diode (note that D2 is shown at the left, not D1)]]<br />
RAMPS is quite happy with the 12 V line from [[PCPowerSupply]].<br />
Or you can hack up a 12V laptop power supply, or other 12 V "wall wart" power supply. <font color="red"> Make sure that the power supply can output 5A or greater.</font> Additional 11A may be needed for heated bed support.<br />
<br />
See Connecting power above.<br />
<br />
The 3 pins next to the reset switch are meant to optionally connect to your PSU.<br />
<br />
The PS_ON pin is intended to switch your power supply on and off. Many firmwares support pulling this pin low with M80 command to turn the power supply on, and M81 to turn it off. This behavior is desired for ATX power supplies and can be modified in firmware to support 5V high power supplies like those borrowed from an Xbox.<br />
<br />
Without D1 installed, or when the 12VIN is not connected, the Arduino gets its power from USB. If you want your kit powered without USB connected you need to solder in D1 OR connect VCC to your PSU.<br />
<br />
The VCC pin can be connected to your ATX's 5Vsb to continuously power the Arduino from your ATX power supply. You will want to make sure that D1 is not installed or cut out. The Arduino is not designed to be powered directly on the VCC rail and the VIN pin at the same time.<br />
<br />
If you want to use PS_ON to turn on your power supply then don't use diode D1, you need your Arduino to be powered from 5Vsb otherwise when no USB is connected the PS_ON pin floats (and your power supply pulses on and off).<br />
<br />
The 5V pin in that connector on RAMPS only supplies the 5V to the auxiliary servo connectors. It is designed so that you can jumper it to the VCC pin and use the Arduino's power supply to supply 5V for extra servos if you are only powered from USB or 5V. Since there is not a lot of extra power from the Arduino's power supply you can connect it<br />
directly to your 5V power supply if you have one. You can also leave this pin not connected if you have no plan to add extra servos.<br />
<br />
===Maximum Input Voltage===<br />
====Power Supply without diode====<br />
There are three limiting factors to the maximum voltage that you can put into the RAMPS:<br />
# The Arduino Mega maximum input voltage<br />
# Filtering capacitor maximum voltages<br />
# PTC fuse maximum voltages<br />
<br />
First, the 1N4004 diode connects the RAMPS input voltage to the Arduino Mega which has a recommended maximum input voltage of 12 volts. If your board does not have this diode soldered in (or if you cut it), you will need to power the Mega through the USB connector or through a separate 5v line, but this allows a higher RAMPS voltage.<br />
<br />
Second, most boards use 25v or 35v aluminum electrolytic capactors (C2, C3, C4, C6, C7, C9, and C10). To be safe, you should only go to half of your rated maximum voltage -- thus if your board has 35v capacitors (code VZA) then you should use a maximum input of 17.5v. The absolute maximum voltage is determined by the pololu servo drivers, which themselves are limited to 35V.<br />
<br />
Third, the MF-R500 (5A) PTC fuse is rated to 30V and the MF-R1100 (11A) PTC fuse is rated to 16V. They will need to be replaced with real fuses.<br />
<br />
====Power Supply with diode====<br />
If your board has a 1N4004 diode soldered in, do not apply more than 12 V to it. Original flavor Arduino Mega are rated to 12 V input. While Arduino Mega 2560 can take 20 V, it is not recommended.<br />
<br />
=Firmware and Pin Assignments=<br />
<br />
<font color="red">RAMPS 1.4 uses the same pin definitions as 1.3.</font><br />
<br />
You will need the Arduino software at http://www.arduino.cc/en/Main/Software to upload the firmware to Arduino Mega. The version of Arduino you need may be determined by the firmware you want to use. The current (as of 2014-01-22) [[List_of_Firmware#Marlin|Marlin]] firmware is compatible with Arduino version 1.0.5. Some other firmwares may require Arduino software version 0023, NOT the most recent version. Please see your firmware documentations if you need assistance.<br />
<br />
Troubleshooting: You may need to make sure that the driver is installed for the Arduino MEGA by going to Control Panel -> Hardware and Sound -> Device Manager. If the device that appears/disappears when you plug in and unplug the board USB is "Unknown Device" under "Other devices", then you need to right click on the device and click the update driver button. Find where on your computer you saved/installed the Arduino software, and tell the wizard to search in the driver folder there. Windows 8 will give this error: "The third party INF does not contain digital signature". If so, save the zip for the latest version of Arduino on your PC, and repeat the steps above with the driver folder in there. It should contain the digital signature Windows needs.<br />
<br />
[[Sprinter]] and [[Marlin]] are popular and stable firmwares for RAMPS as of 3/28/2012. [[Pronterface]] is a cross platform printer control program that can be used for testing/printing.<br />
<br />
Working preconfigured '''Sprinter''' firmware can be downloaded here: [[file:UltiMachineRAMPS1-4Sprinter.zip]]. Mechanical is in the folder ending with ME, optical endstop firmware is in the folder ending in OE.<br />
<br />
Working preconfigured '''Marlin''' firmware can be downloaded at<br />
http://adf.ly/1RKUfV . is for mechanical endstops. For optical, you will need to reverse the endstop logic in configuration.h. The language of display is in italian, but can easy be changed in language.h. It is preconfigured for the RepRap Discount Smart Controller and similar LCD module. You will need to disable LCD in configuration.h if not using it.<br />
<br />
Others (Need pins set in Firmware as below):<br />
<br />
*mechanical endstops (now the default ultimachine.com option) require '''#define OPTO_PULLUPS_INTERNAL 1''' to be added to configuration.h if not there by default.<br />
<br />
Here are the pin definitions for this board.<br />
<pre><br />
// For RAMPS 1.4<br />
#define X_STEP_PIN 54<br />
#define X_DIR_PIN 55<br />
#define X_ENABLE_PIN 38<br />
#define X_MIN_PIN 3<br />
#define X_MAX_PIN 2<br />
<br />
#define Y_STEP_PIN 60<br />
#define Y_DIR_PIN 61<br />
#define Y_ENABLE_PIN 56<br />
#define Y_MIN_PIN 14<br />
#define Y_MAX_PIN 15<br />
<br />
#define Z_STEP_PIN 46<br />
#define Z_DIR_PIN 48<br />
#define Z_ENABLE_PIN 62<br />
#define Z_MIN_PIN 18<br />
#define Z_MAX_PIN 19<br />
<br />
#define E_STEP_PIN 26<br />
#define E_DIR_PIN 28<br />
#define E_ENABLE_PIN 24<br />
<br />
#define SDPOWER -1<br />
#define SDSS 53<br />
#define LED_PIN 13<br />
<br />
#define FAN_PIN 9<br />
<br />
#define PS_ON_PIN 12<br />
#define KILL_PIN -1<br />
<br />
#define HEATER_0_PIN 10<br />
#define HEATER_1_PIN 8<br />
#define TEMP_0_PIN 13 // ANALOG NUMBERING<br />
#define TEMP_1_PIN 14 // ANALOG NUMBERING<br />
</pre><br />
<br />
==Source==<br />
<br />
{|class="wikitable" style="margin: 1em auto 1em auto;"<br />
|- style="background-color:#999999;" <br />
! FILE ID#<br />
! TYPE<br />
! DESCRIPTION<br />
! DOWNLOAD<br />
|-<br />
| [[File:ArduinoMegaPololuShield.zip]]<br />
| Eagle Files<br />
| These are the files you need to make the board.(Use the File: link to the left to access older versions of the file.)<br />
| [[media:ArduinoMegaPololuShield.zip]]<br />
|-<br />
|-<br />
| [[File:RepRapjr.lbr]]<br />
| Eagle Libraries<br />
| The components used in this board are here. see [[Eagle_Library]]<br />
| [[media:RepRapjr.lbr]]<br />
|-<br />
|}<br />
<br />
==Bill of Materials==<br />
{| border="1"<br />
|-<br />
! ID<br />
! Description<br />
! Quantity<br />
! Part Number<br />
! Reichelt Order Number<br />
! Digikey Part Number (Description) <br />
|-<br />
| U1<br />
| Arduino Mega or clone<br />
| 1<br />
|2560 or 1280<br />
|<br />
|[http://www.digikey.com/product-detail/en/A000067/1050-1018-ND/2639006 1050-1018-ND](BOARD MCU MEGA2560)<br />
|-<br />
| U2,U3,U4,U5<br />
| [[Pololu stepper driver board]]s or clones<br />
| 4<br />
| A fifth one can be used for a 2nd extruder or extra axis<br />
|<br />
|N/A<br />
|-<br />
| C2<br />
| 100nF capacitor (0805)(> highest planned voltage)<br />
| 1<br />
| <br />
|<br />
|[http://www.digikey.com/product-detail/en/CC0805KRX7R8BB104/311-1141-1-ND/303051 311-1141-1-ND](CAP CER 0.1UF 25V 10% X7R 0805)<br />
|-<br />
| C1,C5,C8<br />
| 10uF capacitor (153CLV-0405)(>5V)<br />
| 3<br />
| <br />
|<br />
|[http://www.digikey.com/product-detail/en/EXV106M025A9BAA/399-6724-1-ND/3082855 399-6724-1-ND](CAP ALUM 10UF 25V 20% SMD)<br />
|-<br />
| C3,C4,C6,C7,C9,C10<br />
| 100uF capacitor (153CLV-0605)(> highest planned voltage)<br />
| 6<br />
|<br />
|<br />
|[http://www.digikey.com/product-detail/en/EXV107M016A9GAA/399-6726-1-ND/3082857 399-6726-1-ND](CAP ALUM 100UF 16V 20% SMD)<br />
|-<br />
| R1,R7,R11,R21,R22<br />
| 4.7K resistor (0805)(1%)<br />
| 5<br />
| <br />
|<br />
|[http://www.digikey.com/scripts/dksearch/dksus.dll?vendor=0&keywords=RHM4.70KAECT-ND+ RHM4.70KAECT-ND](RES 4.70K OHM .4W 1% 0805) <br />
|-<br />
| R2,R3,R4,R5,R6,R8,R9,R10<br />
| 100K resistor (0805)<br />
| 8<br />
| <br />
|<br />
|[http://www.digikey.com/product-detail/en/ESR10EZPF1003/RHM100KAECT-ND/1983806 RHM100KAECT-ND](RES 100K OHM .4W 1% 0805)<br />
|-<br />
| R12<br />
| 1K resistor (0805)<br />
| 1<br />
| <br />
|<br />
|[http://www.digikey.com/product-detail/en/ESR10EZPF1001/RHM1.00KAECT-ND/1983804 RHM1.00KAECT-ND](RES 1.00K OHM .4W 1% 0805)<br />
|- <br />
| R23,R24,R25<br />
| 1.8K resistor (0805)<br />
| 3<br />
|<br />
|<br />
|[http://www.digikey.com/product-detail/en/RC0805FR-071K8L/311-1.80KCRCT-ND/730467 311-1.80KCRCT-ND](RES 1.80K OHM 1/8W 1% 0805)<br />
|-<br />
| R16,R17,R18,R19,R20<br />
| 10K resistor (0805)<br />
| 5<br />
|<br />
|<br />
|[http://www.digikey.com/product-detail/en/ERJ-6ENF1002V/P10.0KCCT-ND/119248 P10.0KCCT-ND](RES 10.0K OHM 1/8W 1% 0805)<br />
|-<br />
| R13,R14,R15<br />
| 10 ohm resistor (0805)<br />
| 3<br />
|<br />
|<br />
|[http://www.digikey.com/product-detail/en/CRCW080510R0FKEAHP/541-10.0TCT-ND/2222835 541-10.0TCT-ND](RES 10.0 OHM .33W 1% 0805)<br />
|-<br />
| Q1,Q2,Q3<br />
| N-channel Mosfet<br />
| 3<br />
| STP55NF06L (<math>R_{DS} = 18 m\Omega</math> On) <br />
Upgrade particularly for the bed:<br />
IRLB8743PBF (<math>R_{DS} = 3.2 m\Omega</math> On) or for even more current<br />
IRLB3034PBF (<math>R_{DS} = 1.5 m\Omega</math> On)<br />
| ZXM 64N035 L3<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=497-6742-5-ND 497-6742-5-ND] (MOSFET N-CH 60V 55A TO-220)<br />
|-<br />
| D1,D2<br />
| Diode<br />
| 2<br />
| 1N4004<br />
| 1N 4004<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=1N4004FSCT-ND 1N4004FSCT-ND] (DIODE GEN PURPOSE 400V 1A DO41)<br />
|-<br />
| F1<br />
| PTC resettable fuse (30V, Hold5A, Trip10A)<br />
| 1<br />
| MF-R500<br />
| PFRA 500<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=MF-R500-ND MF-R500-ND] (FUSE PTC RESETTABLE 5A HOLD)<br />
|-<br />
| F2<br />
| PTC resettable fuse (Hold11A)<br />
| 1<br />
| MF-R1100<br />
| <br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=RGEF1100-ND RGEF1100-ND] (POLYSWITCH RGE SERIES 11.0A HOLD)<br />
|-<br />
| J2<br />
| D8-D10 Outputs // 6 position screw terminal (min 11A per contact) OR Jack/Plug connector pair<br />
| 1<br />
| 282837-6<br />
| AKL 101-06<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=WM7857-ND WM7857-ND] (CONN TERMINAL BLOCK 6POS 5.08MM) <br />
<br />
OR <br />
<br />
[http://www.digikey.com/product-detail/en/phoenix-contact/1935200/277-1581-ND/568618 1935200] (TERM BLOCK PCB 6POS 5.0MM)<br />
<br />
OR <br />
<br />
1x [http://www.digikey.com/product-detail/en/20020109-H061A01LF/609-4284-ND/2509130 609-4284-ND] & 1x [http://www.digikey.com/scripts/DkSearch/dksus.dll?WT.z_header=search_go&lang=en&keywords=609-4218-ND&x=0&y=0&cur=USD 609-4218-ND]. [https://lh6.googleusercontent.com/--1nJttlNQDs/UNfmaLXKiTI/AAAAAAAADxQ/Z6CSD4V8r6I/s617/20121223_194819.jpg May prevent overtemp events] <br />
|-<br />
| LED1<br />
| Green LED (0805)<br />
| 1<br />
|<br />
|<br />
|[http://www.digikey.com/product-detail/en/CMD17-21VGD%2FTR8/L62505CT-ND/254936 L62505CT-ND](LED GREEN DIFF 0805 SMD)<br />
|-<br />
|LED2,LED3,LED4<br />
| Red LED (0805)<br />
| 3<br />
|<br />
|<br />
|[http://www.digikey.com/product-detail/en/CMD17-21VRD%2FTR8/L62501CT-ND/254934 L62501CT-ND](LED HI EFF RED DIFF 0805)<br />
|-<br />
| S1<br />
| Push button switch<br />
| 1<br />
| B3F-3100 <br />
| TASTER 3305B (should fit footprint also, but button will overhang board edge)<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=450-1648-ND 450-1648-ND] (SWITCH TACT RA H=6.35MM)<br />
|-<br />
| X1<br />
| Power jack (Plug and fixed receptacle)(Min 11A per position more is better)<br />
| 1<br />
| MSTBA 2,5 and MSTBT 2,5 (5.04mm spacing 4 connector)<br />
| <br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=WM7847-ND WM7847-ND] (CONN HEADER 4POS 5.08MM R/A TIN) &amp; [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=WM7953-ND WM7953-ND] (CONN TERM BLOCK 4POS 5.08MM R/A)<br />
<br />
OR<br />
<br />
[http://www.digikey.com/product-detail/en/phoenix-contact/1935187/277-1579-ND/568616 1935187] (TERM BLOCK PCB 4POS 5.0MM)<br />
|-<br />
|<br />
| 2 x 3 pin header<br />
| 8<br />
| 961206-6404-AR<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=3M9459-ND 3M9459-ND] (CONN HEADER VERT DUAL 6POS GOLD)<br />
|-<br />
| <br />
| 4 pin header<br />
| 5<br />
| 961104-6404-AR<br />
| SL 1X36G 2,54 (3 of these)<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=3M9449-ND 3M9449-ND] (CONN HEADER VERT SGL 4POS GOLD)<br />
|-<br />
| <br />
| 6 pin header<br />
| 2 (? - from http://gala-automation.com/index.php/component/content/article/26-reprap-tutorials/42-ramps-14-bom)<br />
| 961106-6404-AR<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=3M9451-ND 3M9451-ND] (CONN HEADER VERT SGL 6POS GOLD)<br />
|-<br />
|<br />
| 2 x 18 Pin Stackable Female Header (non stackables can be used with plated through holes)<br />
| 1<br />
| <br />
| MALE: SL 2X25G 2,54 (2 of them, shortened with a saw or pliers)<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7121-ND S7121-ND] (CONN HEADER FMAL 36PS.1" DL GOLD) - Not Stackable<br />
|-<br />
| <br />
| 8 Pin Stackable Female Header (non stackables can be used with plated through holes)<br />
| 5<br />
|<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7041-ND S7041-ND] (CONN HEADER FEMALE 8POS .1" GOLD) - Not Stackable<br />
|-<br />
| <br />
| 6 Pin Stackable Female Header (non stackables can be used with plated through holes)<br />
| 1<br />
|<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7039-ND S7039-ND] (CONN HEADER FEMALE 6POS .1" GOLD) - Not Stackable<br />
|-<br />
| <br />
| 24 Pin Female Header * Note *<br />
| 2<br />
| Required to carry enough current for motors<br />
| <br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7057-ND S7057-ND] (CONN HEADER FMALE 24POS .1" GOLD) - Rated @ 3A / Pin<br />
|-<br />
| <br />
| 8 Pin Female Header * Note *<br />
| 4<br />
| Required to carry enough current for motors<br />
| <br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7041-ND S7041-ND] (CONN HEADER FEMALE 8POS .1" GOLD) - Rated @ 3A / Pin<br />
|-<br />
|<br />
| 0.1" Jumpers<br />
| 15<br />
|<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=A26242-ND A26242-ND] (SHUNT LP W/HANDLE 2 POS 30AU)<br />
|-<br />
|<br />
| Circuit Board<br />
|1<br />
|v1.4<br />
|<br />
|N/A<br />
|}<br />
Note * You can use Female Headers which are not the exact size, but they are hard to break/cut so in this case buy some extra! (one wasted header per cut)<br />
<br />
A BOM for sourcing the RAMPS components from Mouser is also available in [https://docs.google.com/spreadsheet/ccc?key=0Auf-66FPv0JidHhtRVB0VVplOURwWklrX0tIeXhsS3c&hl=en_US#gid=0 this google spreadsheet] (This list is incomplete and has missing or incorrect quantities.)<br />
<br />
Shopping lists for v1.4 [http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=d126a71257] .<br />
<br />
= BT Extension =<br />
: ''main article: [[jy-mcu]]''<br />
In order to get rid of the USB connection between RAMPS and the PC, you may like to use Bluetooth. There is a cheap module available in the market called 'JY-MCU' (vendor Shenzhen Jiayuan Electronic Co.,Ltd.).<br />
<br />
[[File:jy-mcu_f.jpg|300px]] [[File:jy-mcu_b.jpg|300px]]<br />
<br />
==Change module setting==<br />
Before the module can be used, the default setting has to be changed. You can connect to and modify the BT JY-MCU module settings via the Arduino mega 2560 using the pin 10 and pin 9 as Rx and Tx terminals, respectively. Make sure you connect Rx on the BT module to the Tx on the arduino and vice versa, in other words Rx goes to Tx and vice versa. Upload the simple code to arduino located on an instructable entitled "Success-Using-the-JY-MCU-linvor-Bluetooth-Module". Use the serial monitor within arduino IDE or another terminal program, with baudrate set to 9600 and 'No Line Ending' selected, enter the following commands: <br />
<br />
AT - the response should be OK (If you see weird characters, the baudrate is wrong--> try a different one<br />
<br />
AT+NAMExxxx - Where xxxx is the friendly name of the module<br />
<br />
AT+BAUDx - Where x sets the baud rate (values & baud rates below)<br />
<br />
AT+VERSION - Returns the firmware version<br />
<br />
AT+PINxxxx - Sets a new pairing code (default: 1234)<br />
<br />
1——1200 <br />
2——2400 <br />
3——4800 <br />
4——9600 <br />
5——19200 <br />
6——38400 <br />
7——57600 <br />
8——115200<br />
<br />
Alternatively, you can connect to the module from PC via USB<->RS232 (RxD/TxD) interface with default settings (9600, N, 8, 1). The module shouldn't be paired at that moment. Use the same AT commands as above.<br />
<br />
More details about the configuration you will find here [[http://reprap.org/wiki/Melzi#Connect_via_Bluetooth]]<br />
<br />
Troubleshooting:<br />
If you see weird characters, the baudrate is wrong--> try a different one<br />
Make sure your Tx and Rx are not mixed up<br />
Make sure you have the proper resistors installed<br />
<br />
==Wiring==<br />
On RAMPS/Arduino Mega the UART level are 5V but the BT module supports only 3.3V input. Therefore the TxD level has to be divided by resistor. This passive solution is fast enough for 115kBaud. Overall only 4 wires have to be soldered. <br />
<br />
[[File:BT_Connection_RAMPS1.4.png|400px]]<br />
<br />
==Connect via Bluetooth==<br />
Once you have setup your BT devices you can select from drop down list and control your RepRap as usual.<br />
<br />
==RAMPS 1.4 test code==<br />
<br />
#define X_STEP_PIN 54<br />
#define X_DIR_PIN 55<br />
#define X_ENABLE_PIN 38<br />
#define X_MIN_PIN 3<br />
#define X_MAX_PIN 2<br />
<br />
#define Y_STEP_PIN 60<br />
#define Y_DIR_PIN 61<br />
#define Y_ENABLE_PIN 56<br />
#define Y_MIN_PIN 14<br />
#define Y_MAX_PIN 15<br />
<br />
#define Z_STEP_PIN 46<br />
#define Z_DIR_PIN 48<br />
#define Z_ENABLE_PIN 62<br />
#define Z_MIN_PIN 18<br />
#define Z_MAX_PIN 19<br />
<br />
#define E_STEP_PIN 26<br />
#define E_DIR_PIN 28<br />
#define E_ENABLE_PIN 24<br />
<br />
#define Q_STEP_PIN 36<br />
#define Q_DIR_PIN 34<br />
#define Q_ENABLE_PIN 30<br />
<br />
#define SDPOWER -1<br />
#define SDSS 53<br />
#define LED_PIN 13<br />
<br />
#define FAN_PIN 9<br />
<br />
#define PS_ON_PIN 12<br />
#define KILL_PIN -1<br />
<br />
#define HEATER_0_PIN 10<br />
#define HEATER_1_PIN 8<br />
#define TEMP_0_PIN 13 // ANALOG NUMBERING<br />
#define TEMP_1_PIN 14 // ANALOG NUMBERING<br />
<br />
void setup() {<br />
pinMode(FAN_PIN , OUTPUT);<br />
pinMode(HEATER_0_PIN , OUTPUT);<br />
pinMode(HEATER_1_PIN , OUTPUT);<br />
pinMode(LED_PIN , OUTPUT);<br />
<br />
pinMode(X_STEP_PIN , OUTPUT);<br />
pinMode(X_DIR_PIN , OUTPUT);<br />
pinMode(X_ENABLE_PIN , OUTPUT);<br />
<br />
pinMode(Y_STEP_PIN , OUTPUT);<br />
pinMode(Y_DIR_PIN , OUTPUT);<br />
pinMode(Y_ENABLE_PIN , OUTPUT);<br />
<br />
pinMode(Z_STEP_PIN , OUTPUT);<br />
pinMode(Z_DIR_PIN , OUTPUT);<br />
pinMode(Z_ENABLE_PIN , OUTPUT);<br />
<br />
pinMode(E_STEP_PIN , OUTPUT);<br />
pinMode(E_DIR_PIN , OUTPUT);<br />
pinMode(E_ENABLE_PIN , OUTPUT);<br />
<br />
pinMode(Q_STEP_PIN , OUTPUT);<br />
pinMode(Q_DIR_PIN , OUTPUT);<br />
pinMode(Q_ENABLE_PIN , OUTPUT);<br />
<br />
digitalWrite(X_ENABLE_PIN , LOW);<br />
digitalWrite(Y_ENABLE_PIN , LOW);<br />
digitalWrite(Z_ENABLE_PIN , LOW);<br />
digitalWrite(E_ENABLE_PIN , LOW);<br />
digitalWrite(Q_ENABLE_PIN , LOW);<br />
}<br />
<br />
void loop () {<br />
<br />
if (millis() %1000 <500) <br />
digitalWrite(LED_PIN, HIGH);<br />
else<br />
digitalWrite(LED_PIN, LOW);<br />
<br />
if (millis() %1000 <300) {<br />
digitalWrite(HEATER_0_PIN, HIGH);<br />
digitalWrite(HEATER_1_PIN, LOW);<br />
digitalWrite(FAN_PIN, LOW);<br />
} else if (millis() %1000 <600) {<br />
digitalWrite(HEATER_0_PIN, LOW);<br />
digitalWrite(HEATER_1_PIN, HIGH);<br />
digitalWrite(FAN_PIN, LOW);<br />
} else {<br />
digitalWrite(HEATER_0_PIN, LOW);<br />
digitalWrite(HEATER_1_PIN, LOW);<br />
digitalWrite(FAN_PIN, HIGH);<br />
}<br />
<br />
if (millis() %10000 <5000) {<br />
digitalWrite(X_DIR_PIN , HIGH);<br />
digitalWrite(Y_DIR_PIN , HIGH);<br />
digitalWrite(Z_DIR_PIN , HIGH);<br />
digitalWrite(E_DIR_PIN , HIGH);<br />
digitalWrite(Q_DIR_PIN , HIGH);<br />
}<br />
else {<br />
digitalWrite(X_DIR_PIN , LOW);<br />
digitalWrite(Y_DIR_PIN , LOW);<br />
digitalWrite(Z_DIR_PIN , LOW);<br />
digitalWrite(E_DIR_PIN , LOW);<br />
digitalWrite(Q_DIR_PIN , LOW);<br />
} <br />
<br />
digitalWrite(X_STEP_PIN , HIGH);<br />
digitalWrite(Y_STEP_PIN , HIGH);<br />
digitalWrite(Z_STEP_PIN , HIGH);<br />
digitalWrite(E_STEP_PIN , HIGH);<br />
digitalWrite(Q_STEP_PIN , HIGH); <br />
delay(1);<br />
<br />
digitalWrite(X_STEP_PIN , LOW);<br />
digitalWrite(Y_STEP_PIN , LOW);<br />
digitalWrite(Z_STEP_PIN , LOW);<br />
digitalWrite(E_STEP_PIN , LOW);<br />
digitalWrite(Q_STEP_PIN , LOW); <br />
}<br />
<br />
=Where to get=<br />
* [http://www.reprap.cc/shop/de/content/ramps-14 Reprap Austria] (worldwide free shipping)<br />
* [http://www.makerfarm.com/index.php/printer-electronics/ramps.html Maker Farm Inc] USA - (worldwide shipping)<br />
* [http://store.thingibox.com/es/electricidad/38-ramps_14.html Thingibox] Spain - (worldwide shipping)<br />
* [https://reprap.pt/pecas/eletronica/ramps-1-4 RepRap.PT] Portugal<br />
* [http://www.reprap.me/electronic/ramps.html RepRap.me Denmark] (worldwide shipping)<br />
* [https://www.tindie.com/products/staticboards/ramps-14-sb-premium/ RAMPS 1.4 Manufactured in Europe with high quality parts for long printing hours] - (worldwide shipping)<br />
* [https://taotac.com/sanpham/ramps/ TaoTac.com]<br />
* [http://www.reprap.cn/ HE3D]<br />
* [http://twelvepro.com/index.php?route=product/product&path=67&product_id=83 Twelvepro]<br />
* [https://www.fabberworld.com/ramps-1-4 Fabberworld]<br />
* [http://aus3d.com.au/printer-parts/printer-electronics/ramps-14 Aus3D]<br />
* [https://www.diy-india.com DIY-India.com] (India)<br />
<br />
=RAMPS 1.4.2=<br />
<br />
[[Image:RAMPS_1.4.2.jpg|800x513px|RAMPS 1.4.2]]<br />
<br />
RAMPS 1.4.2 has minor changes over RAMPS 1.4. The RAMPS 1.4.2 has below enhancements over 1.4<br />
<br />
* Standard blade fuses instead of thermal fuses increasing the heat resilience.<br />
* Current carrying improved by increasing the thickness of the cooper at the PCB from 35 to 70 micro meters.<br />
* Suppression caps added to each end-stop to avoid spurious signals.<br />
* Added an additional connector to XY, E1 and E2 to connect a second stepper motor.<br />
* Connector for external reset added.<br />
* Labeled D8, D9,D10 with Heatbed, Extruder 1 Fan and Extruder 2.<br />
<br />
Eagle CAD files: [https://github.com/GermanRepRap/Ramps-1.4.2 https://github.com/GermanRepRap/Ramps-1.4.2]<br />
<br />
==Where to buy RAMPS 1.4.2==<br />
<br />
<br />
Fully assembled available from [http://www.germanreprap.com German RepRap]<br />
<br />
[http://store.thingibox.com/en/electrical/38-ramps_14.html Full assembled and RAMPS-FD] from Thingibox.<br />
<br />
=Modifications, hacks and add-ons=<br />
==Using 24v on RAMPS== <br />
Details can be found on this page [http://reprap.org/wiki/RAMPS_24v http://reprap.org/wiki/RAMPS_24v]<br />
==Adding LEDS to RAMPS==<br />
Details can be found on this page [http://reprap.org/wiki/RAMPS_LEDs http://reprap.org/wiki/RAMPS_LEDs]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=RAMPS_1.4&diff=181304RAMPS 1.42018-01-17T15:17:49Z<p>Merlucin: /* Where to buy RAMPS 1.4.2 */</p>
<hr />
<div>{{RAMPS}}<br />
<br />
{{Languages|RAMPS 1.4}}<br />
<br />
{{Development<br />
|image = RAMPS1-3 fin.JPG<br />
|status = Working<br />
|name = RAMPS 1.4<br />
|description = RepRap Arduino Mega Pololu Shield<br />
Arduino MEGA based modular RepRap electronics.<br />
|license = [[GPL]]<br />
|author = johnnyr<br />
|reprap = Pololu Electronics<br />
|categories = {{tag|RAMPS}} {{tag|8/16-bit board}}<br />
}}<br />
<br />
<br/><br />
<br />
=Summary=<br />
<br />
In RAMPS 1.4, the resistors and capacitors are now surface mount to fit more passive components. This does add another set of steps to assembly, but we stuck with larger sizes to make it fairly painless.<br />
<br />
<gallery><br />
Image:RAMPS1-3 fin.JPG<br />
Image:Arduinomega1-4connectors.png<br />
Image:RAMPS1.4schematic.png<br />
Image:Ramps_v1.4_shield_bothsides.png<br />
</gallery><br />
<br />
Reference board orientation is component side up, power inputs to the left.<br />
<br />
= Safety Tip =<br />
<br />
[[image:Generation3Electronics-achtung.gif|left]]<br />
<br />
Once you start putting electricity into your RepRap - even at just 12 volts - you have to take basic, common sense precautions to avoid fires. Just in case these fail, test your workshop [http://en.wikipedia.org/wiki/Smoke_detector smoke detector]. Got no smoke detector? Get one!<br />
<br />
<br clear="all"/><br />
<br />
= '''WARNING''' - THERMAL-isolation-related DESIGN FLAW IN Power handling capacity of '''PRODUCTION''' RAMPS 1.4 boards =<br />
<br />
A "thermals" design flaw has been noted in the RAMPS 1.4 Eagle CAD files. This has been confirmed by visual inspection of production boards, which consistently shows only between two and three (almost never four) thermal-isolating traces per side of the PCB, to power-carrying pins, of under a 0.5 amp carrying-capacity per trace, assuming a 1oz copper thickness.<br />
<br />
[[image:RAMPS_1_4_THERMAL_DESIGN_FLAW.jpg|600px]]<br />
<br />
The problem may be fixed in the Eagle CAD files - for a future version of RAMPS ''only'' - by disabling "thermals" on the GND, +12V and the +12V2 Copper pour. However on existing (mass-produced) RAMPS 1.4 boards, estimating the total widths (including all thermals from all tracks on both sides of the PCB) checking with an online copper width calculator and adding up the total current, assuming a 1oz copper PCB the maximum safe current on the fuses (giving only a 10C rise in temperature of the thermal-isolation tracks) is only around 6 (six) amps and in other areas the maximum safe current (assuming the same 10C rise in temperature) is around 8 (eight) amps.<br />
<br />
This problem may potentially be fixed on existing RAMPS 1.4 boards by augmenting the power traces with suitably-thick insulated wires with sufficient current-carrying capacity, soldering them to '''all''' the relevant pins.<br />
<br />
A video with a full walkthrough including calculating the total track width and inputting it into a trace width current calculator is here:<br />
https://youtu.be/4Ff_XG1OPIM<br />
<br />
<br clear="all"/><br />
<br />
=Assembly=<br />
==Component Soldering==<br />
==Required Tools==<br />
You must have:<br />
Solder iron, solder wire, good tweezers<br />
You really need:<br />
Solder wick, solder sucker, flux pen<br />
Optional methods use:<br />
Solder paste, hot plate or oven <br />
<br />
===Shield Assembly===<br />
[[Image:RAMPS1-3pasteapplied.JPG|thumb]] <br />
Soldering RAMPS 1.4 includes both surface mount and through hole soldering.<br />
<br />
The surface mount can be done a few ways. Since all the SMT components on this board are large 2 pad parts you can do pin by pin soldering pretty easy with normal soldering equipment. Start by putting a small amount of solder on one pad. If you have flux, coat the soldered pad. Use the tweezers to hold the component down in position and heat the solder to tack the component into place (make sure the entire solder blob flows so you don't get a cold solder). Then solder the other pad. Also popular is using solder paste for pad by pad soldering, Oven Reflow (need link), and [[HotplateReflowTechnique]]<br />
<br />
Solder the SMT components first. Then the PTH on top of the board. Finally solder the pin headers on the bottom.<br />
<br />
==== C2 - 100nF capacitor====<br />
[[Image:RAMPS1-3 100nF.JPG|thumb]]<br />
This can be placed in any orientation.<br />
<br clear="all"/><br />
==== LED1 - Green LED====<br />
[[Image:RAMPS1-3 GrLED.JPG |thumb]]<br />
Place these with the end having green dots away from the + mark on the PCB.<br />
<br clear="all"/><br />
<br />
==== LED2, LED3, LED4 - Red LED====<br />
[[Image:RAMPS1-3 redLEDs.JPG |thumb]]<br />
Place these with the end having green dots away from the + mark on the PCB.<br />
<br clear="all"/><br />
====R13, R14, R15 - 10 Ohm resistor====<br />
[[Image:RAMPS1-3 10r.JPG|thumb]]<br />
These can be placed in any orientation.<br />
<br clear="all"/><br />
====R12 - 1K resistor====<br />
[[Image:RAMPS1-3 1k.JPG |thumb]]<br />
These can be placed in any orientation.<br />
<br clear="all"/><br />
====R23, R24, R25 - 1.8K resistor====<br />
[[Image:RAMPS1-3 1-8k.JPG |thumb]]<br />
These are marked 1K on the PCB, but we are using larger ones to accommodate higher voltages. These can be placed in any orientation.<br />
<br clear="all"/><br />
<br />
====R1, R7, R11, R21, R22 - 4.7K resistor====<br />
[[Image:RAMPS1-3 4-7k.JPG|thumb]]<br />
These can be placed in any orientation.<br />
<br clear="all"/><br />
====R16, R17, R18, R19, R20 - 10K resistor====<br />
[[Image:RAMPS1-3 10k.JPG|thumb]]<br />
These can be placed in any orientation.<br />
<br clear="all"/><br />
====R2, R3, R4, R5, R6, R8, R9, R10 - 100K resistor====<br />
[[Image:RAMPS1-3 100k.JPG |thumb]]<br />
These can be placed in any orientation.<br />
<br clear="all"/><br />
====C1, C5, C8 - 10uF capacitor====<br />
[[Image:RAMPS1-3 10uF.JPG|thumb]]<br />
These must be placed in the proper orientation. The board has the foot print of the components printed on it. The rounded corners on the base of the capacitor must line up with the white print on the PCB.<br />
<br clear="all"/><br />
<br />
====C3, C4, C6, C7, C9, C10 - 100uF capacitor====<br />
[[Image:RAMPS1-3 100uF.JPG|thumb]]<br />
These must be placed in the proper orientation. The board has the foot print of the components printed on it. The rounded corners on the base of the capacitor must line up with the white print on the PCB. <br />
<br clear="all"/><br />
<br />
====Reflow SMT soldering====<br />
[[Image:RAMPS1-3_placed.JPG|200px|thumb]] [[Image:RAMPS1-3 smtSoldered.JPG|thumb]]<br />
If you are doing oven or hot plate method, now is the time apply heat (add links here). If you used a solder iron, you have probably already soldered all these components.<br />
<br />
Make sure to inspect the SMT soldering at this point since it will be harder to rework after the headers are on top.<br />
<br clear="all"/><br />
====Top pins====<br />
[[Image:RAMPS1-3 tpins.JPG|thumb]]<br />
Solder 1 1x6, 6 1x4, and 7 2x3 pin headers on top of the board. The long post should be standing up to take a connector. Solder one leg on each one to tack them into place. Then re-heat the joint and push on the component until it is perfectly situated. Then you'll want to solder the rest of the leads. You will get burnt if you touch the other side of the pin you are soldering.<br />
<br />
If you want to use the extra pin outputs, now is the time to solder on the rest of the headers.<br />
<br clear="all"/><br />
<br />
====Driver sockets====<br />
[[Image:RAMPS1-3 DrSockets.JPG |thumb]]<br />
Place the female headers for the stepper drivers on top of the board. You can use the 1x8 and 1x6 pin headers to jig them straight. Turn the board over and solder these pins.<br />
<br clear="all"/><br />
====D1, D2 - Diodes====<br />
[[Image:RAMPS1-3 DnF.JPG|thumb]]<br />
[[Image:D1D2.jpg|thumb|Where to find the D1 and D2 diodes]]<br />
These must be placed in the proper orientation. The band on the diode must be turned the same way as the mark on the board.<br />
<br />
Definitely solder D2 in. D2, F1, and F2 are shown installed here.<br />
<br />
D1 should only be installed if the 5A rail is powered by 12V. It can be omitted and the Arduino will be powered from USB. You will want D1 installed if you add components to print without a PC. To reiterate, D1 MUST be omitted if you are powering the 5A rail by more than 12V, or the power is not absolutely clean, otherwise you may damage your ramps.<br />
<br style="clear: both" /><br />
<br />
====F1 - MFR500 Fuse====<br />
This is the smaller yellow fuse. This can be placed in any orientation. When soldering the fuses it is best to use a piece of 3mm filament or something similar to keep the ceramic coating on the pins from blocking proper solder along the through hole.<br />
<br />
Since the fuses are the tallest parts, it is simpler and more convenient to solder them last. From this point on, solder the rest of the RAMPS in order of bottom pins, reset switch, terminals, mosfets and then fuses.<br />
<br />
====Bottom pins====<br />
[[Image:RAMPS1-3 bpins.JPG|thumb]]<br />
[[image:DSC 0148.JPG|thumb]]<br />
Place these on the bottom of the board with the long post out to plug into the Arduino MEGA. You can plug them into the MEGA to hold them in place while you solder. Do not overheat the pins while in Arduino or you may damage its connectors.<br />
<br clear="all"/><br />
<br />
====Reset switch====<br />
[[Image:RAMPS1-3 rst.JPG|thumb]]<br />
This can only be oriented in one direction.<br />
<br clear="all"/><br />
====Mosfet Terminal====<br />
[[Image:RAMPS1-3 6pos.JPG |thumb|Standard RAMPS 1.4 D8-10 Terminal Block]]<br />
[[Image:RAMPS1-4 6pos_alt.png |thumb|Alternative Plug/Jack Connectors]]<br />
This must be oriented where the wire holes are turned towards the edge of the board. Solder a pin on each end and make sure the component is flat on the board and solder the middle pins.<br />
<br clear="all"/><br />
====Power Terminal====<br />
[[Image:RAMPS1-3 4pos.JPG|thumb]]<br />
This can only be oriented in one direction.<br />
<br clear="all"/><br />
====Q1, Q2, Q3 - Mosfets====<br />
[[Image:RAMPS1-3 mosfet.JPG|thumb]]<br />
These must be orientated as in the picture. The tall heat sink part of the mosfet needs to be turned the same as the mark on the board.<br />
<br clear="all"/><br />
====F2 - MFR1100 Fuse====<br />
This is the larger yellow fuse. This can be placed in any orientation.<br />
<br clear="all"/><br />
<br />
====Inspection====<br />
[[Image:RAMPS1-3 fin.JPG|200px|thumb]]<br />
Inspect your work. Clean any solder bridges and suspect solders.<br />
<br />
===Stepper Driver Boards===<br />
#*Jumpers need to be installed under each stepper driver:<br />
<br />
jumper Yes/No step size<br />
1 2 3<br />
no no no full step<br />
yes no no half step<br />
no yes no 1/4 step<br />
yes yes no 1/8 step<br />
no no yes 1/16 step<br />
yes no yes 1/32 step<br />
no yes yes 1/64 step<br />
yes yes yes 1/128 step<br />
<br />
If the jumpers set it to a higher number of micro steps than supported by the driver it will operate at the maximum number of micro steps for that driver.<br />
For now the default is maximum micro stepping (all jumpers installed under drivers), which results in 1/16 micro stepping for A4988 drivers and 1/32 for DRV8825. Although for efficiency and accuracy you should opt for the biggest steps that will yield sufficient resolution. Eg. you don't need 5000 steps per millimeter and [http://www.micromo.com/microstepping-myths-and-realities micro-steps] less than 1/16 have reduced torque per step, reduced accuracy and higher driver load].<br />
<br />
Note: This can vary for different drivers.<br />
<br />
#Cut the pin headers to 8 pins long so that they fit each side of the stepper driver.<br />
#Insert the pin headers into the sockets on RAMPS<br />
#Fit the stepper drivers onto the pin headers and solder. Only heat each pin for a few seconds at time to avoid damage to the socket. <br />
#*Glue the heatsink (if used) to the top of the [[A4988]]/[[A4983]] chip using the provided pad of double-sided adhesive.<br />
<br />
===Opto Endstops===<br />
Opto endstop build instructions can be found at [[Gen7_Endstop_1.3.1]], and also [http://reprapsource.com/oe-r1 here] for reprapsource.com's instructions.<br />
#* Cut the 26awg 3 conductor cable into 3 length.[[Image:RAMPSendstopConnector.JPG|right|200px|Close up of endstop connector on endstop.]]<br />
#* Note: you may want to wait until you've built your machine to cut the cables to the perfect length.[[Image:RAMPSendstopConboard.JPG|right|200px|Close up of endstop connection on RAMPS]]<br />
##* crimp and solder a female connector to the ends of each wire. (solder not necessary with proper crimp tools) <br />
#* use the 2.54mm 1x3 housing.<br />
#* Connect at least the minimum endstops. <br />
{| border="1"<br />
| RAMPS End<br />
|-<br />
| SIG (S)<br />
| White<br />
| Top pin<br />
|-<br />
| GND (-)<br />
| Black<br />
| Center pin<br />
|-<br />
| VCC (+)<br />
| Red<br />
| Lower pin<br />
|}<br />
{| border="1" <br />
| Endstop End<br />
|<br />
|-<br />
| VCC (+)<br />
| Red<br />
|-<br />
| SIG (S)<br />
| White<br />
|-<br />
| GND (-)<br />
| Black<br />
|}<br />
<br />
===Mechanical Endstops===<br />
[[File:MechSwitches 2Wire.JPG|thumb]]<br />
The recommended firmware will provide a configuration to use mechanical endstops with just two wires. <br />
<br />
Find the area labelled "endstops" in the upper right corner of the board and for each of the X, Y, and Z pairs of pins (label should be below each set) do the following: <br />
# Connect S (top row, labelled to the left) on RAMPS to NC on the switch.<br />
# Connect GND on RAMPS to C on the switch.<br />
<br />
'''Note:''' The latest firmware such as Marlin seems to use NO as the default pin on the switch. Otherwise you may need to invert the endstops in the firmware. You can use M119 to check your endstops status.<br />
<br />
===Put the connectors on the motor wires===<br />
#* solder a female connector to the ends of each wire.<br />
#* use the 2.54mm 1x3 housing. <br />
#* Shown is the type used for servos in RC projects. See [[Stepper Motors]] for info on motors.<br />
<br />
===Thermistor Wires===<br />
Use a 2 pin 0.1" connector to terminate the thermistor wires.<br />
#* Connect the cable so the 2 wires go to T0<br />
#Connect the 2 heater wires to D10 (E0H on older boards) and the + connection above it.<br />
#* If changing to an unverified firmware it is best to verify heater circuit function with a meter before connecting heater to prevent damage to the extruder.<br />
<br />
===Pololu carriage===<br />
[[image:PololuExample.JPG|thumb]]<br />
This section assumes you are using Pololu, but there are other options. Insert two 1x8 pin headers into the board. If you bought a kit with one 16 pin header, simply cut it so that you have two 1x8. Make sure that the side with the labels has the long ends of the posts, and the side you want to solder is the side with the heat sink. Doing this backwards will cause you not to see the labels and will most likely not fit. Remember to apply a heat-sink to the largest chip on the back.<br />
<br />
Insert the motor boards with the potentiometer to the right side (furthest from the power connectors).<br />
<br />
=Final Setup=<br />
==Pre-Flight Check==<br />
If you think you may have mistakes you can install only one stepper driver during initial testing and risk only one stepper driver.<br />
<br />
The trimpot on the stepper drivers controls the current limit. Turn it all the way down (counter clock wise) and back up 25%. Be careful to not force the trimpot, it is delicate. You will need to fine tune the current limit later. Note that it is allways giving the motors that much power, even when not moving, so if your stepper motor drivers are getting hot, you may want to turn it down slightly.<br />
<br />
[http://reprap.org/mediawiki/index.php?title=Arduino_Mega_Pololu_Shield#Make_the_cables_up_for_the_opto_endstops Connect the minimum endstops] for X,Y, and Z<br />
<br />
Connect Motors (Do not disconnect or connect motors while powered; if the connection is loose, this will cause the motors to misbehave and possibly kill your stepper driver.)<br />
<br />
You may want to use this [http://reprap.org/wiki/File:RAMPSTestCode.pde code] to test all the electronics before installing any of the suggested firmwares.<br />
<br />
Install firmware (More info below). Firmware flashing can be done without 12V power supply connected.<br />
<br />
==Wiring==<br />
It is relatively simple to wire up the RAMPS. Just add the extruder heating coil wire to D10, the thermistor to the two T0 pins on middle right right, and wire up the steppers and endstops. From left to right, wire all of the stepper motor's wires as red, blue, green, and black or red, green, yellow, blue into the pins next to the Pololus. When you connect the wires to the endstops (if you are using 3 endstops, plug them into the MIN (-) slots), make sure you match the labels. <br />
<br />
[[Image:Rampswire14.svg|500px|]]<br />
<br />
Note that Tesla & Tonok firmware use D9 and Sprinter, Marlin, and Johnny/Tonok use D10 for the extruder hot end.<br />
<br />
===Warnings===<br />
<br />
<font color="red">Reversing +/- or otherwise incorrectly connecting power can destroy your electronics and cause fire hazard.<br />
<br />
Incorrectly inserting stepper drivers will destroy your electronics and cause a fire risk. Always make sure power and USB is disconnected when removing or adjusting stepper drivers. Always make sure to insert drivers in correct orientation and in the socket correctly.<br />
<br />
The endstop pins are Signal - GND - VCC, instead of the VCC - Sig - GND like the rest of RepRaps boards. Make sure to wire them correctly. This is done to allow squeezing fatter traces on the printable board.<br />
<br />
DON'T secure Arduino/RAMPS with conductive screws through both mounting holes. The screw may cut into the positive trace creating a HIGH current short.</font><br />
<br />
==Connecting Power==<br />
<br />
Connect your 12V power supply to the RAMPS shield. <font color="red">Reversing +/- or otherwise incorrectly connecting power can destroy your electronics and cause fire hazard</font>.<br />
<br />
The bottom pair of connectors marked 5A power the stepper drivers and Extruder heater/fan (D9, D10). The source should be rated a minimum of 5A.<br />
<br />
The pair of connectors above marked 11A power a Heated Bed, or other output (D8). The source should be rated a minimum 11A (if both power rails are connected to the same supply it should have a minimum rating of 16A).<br />
<br />
The barrel connector, on the Arduino MEGA, will NOT power RAMPS and will not provide power to the stepper motors, heated bed, etc.<br />
<br />
The power connector plug may not be obviously labeled, looking at the power connection the positive is on the left and the negative is on the right of the plug.<br />
<br />
==Power Supply==<br />
[[Image:D1D2.jpg|thumb|Where to find the D1 diode (note that D2 is shown at the left, not D1)]]<br />
RAMPS is quite happy with the 12 V line from [[PCPowerSupply]].<br />
Or you can hack up a 12V laptop power supply, or other 12 V "wall wart" power supply. <font color="red"> Make sure that the power supply can output 5A or greater.</font> Additional 11A may be needed for heated bed support.<br />
<br />
See Connecting power above.<br />
<br />
The 3 pins next to the reset switch are meant to optionally connect to your PSU.<br />
<br />
The PS_ON pin is intended to switch your power supply on and off. Many firmwares support pulling this pin low with M80 command to turn the power supply on, and M81 to turn it off. This behavior is desired for ATX power supplies and can be modified in firmware to support 5V high power supplies like those borrowed from an Xbox.<br />
<br />
Without D1 installed, or when the 12VIN is not connected, the Arduino gets its power from USB. If you want your kit powered without USB connected you need to solder in D1 OR connect VCC to your PSU.<br />
<br />
The VCC pin can be connected to your ATX's 5Vsb to continuously power the Arduino from your ATX power supply. You will want to make sure that D1 is not installed or cut out. The Arduino is not designed to be powered directly on the VCC rail and the VIN pin at the same time.<br />
<br />
If you want to use PS_ON to turn on your power supply then don't use diode D1, you need your Arduino to be powered from 5Vsb otherwise when no USB is connected the PS_ON pin floats (and your power supply pulses on and off).<br />
<br />
The 5V pin in that connector on RAMPS only supplies the 5V to the auxiliary servo connectors. It is designed so that you can jumper it to the VCC pin and use the Arduino's power supply to supply 5V for extra servos if you are only powered from USB or 5V. Since there is not a lot of extra power from the Arduino's power supply you can connect it<br />
directly to your 5V power supply if you have one. You can also leave this pin not connected if you have no plan to add extra servos.<br />
<br />
===Maximum Input Voltage===<br />
====Power Supply without diode====<br />
There are three limiting factors to the maximum voltage that you can put into the RAMPS:<br />
# The Arduino Mega maximum input voltage<br />
# Filtering capacitor maximum voltages<br />
# PTC fuse maximum voltages<br />
<br />
First, the 1N4004 diode connects the RAMPS input voltage to the Arduino Mega which has a recommended maximum input voltage of 12 volts. If your board does not have this diode soldered in (or if you cut it), you will need to power the Mega through the USB connector or through a separate 5v line, but this allows a higher RAMPS voltage.<br />
<br />
Second, most boards use 25v or 35v aluminum electrolytic capactors (C2, C3, C4, C6, C7, C9, and C10). To be safe, you should only go to half of your rated maximum voltage -- thus if your board has 35v capacitors (code VZA) then you should use a maximum input of 17.5v. The absolute maximum voltage is determined by the pololu servo drivers, which themselves are limited to 35V.<br />
<br />
Third, the MF-R500 (5A) PTC fuse is rated to 30V and the MF-R1100 (11A) PTC fuse is rated to 16V. They will need to be replaced with real fuses.<br />
<br />
====Power Supply with diode====<br />
If your board has a 1N4004 diode soldered in, do not apply more than 12 V to it. Original flavor Arduino Mega are rated to 12 V input. While Arduino Mega 2560 can take 20 V, it is not recommended.<br />
<br />
=Firmware and Pin Assignments=<br />
<br />
<font color="red">RAMPS 1.4 uses the same pin definitions as 1.3.</font><br />
<br />
You will need the Arduino software at http://www.arduino.cc/en/Main/Software to upload the firmware to Arduino Mega. The version of Arduino you need may be determined by the firmware you want to use. The current (as of 2014-01-22) [[List_of_Firmware#Marlin|Marlin]] firmware is compatible with Arduino version 1.0.5. Some other firmwares may require Arduino software version 0023, NOT the most recent version. Please see your firmware documentations if you need assistance.<br />
<br />
Troubleshooting: You may need to make sure that the driver is installed for the Arduino MEGA by going to Control Panel -> Hardware and Sound -> Device Manager. If the device that appears/disappears when you plug in and unplug the board USB is "Unknown Device" under "Other devices", then you need to right click on the device and click the update driver button. Find where on your computer you saved/installed the Arduino software, and tell the wizard to search in the driver folder there. Windows 8 will give this error: "The third party INF does not contain digital signature". If so, save the zip for the latest version of Arduino on your PC, and repeat the steps above with the driver folder in there. It should contain the digital signature Windows needs.<br />
<br />
[[Sprinter]] and [[Marlin]] are popular and stable firmwares for RAMPS as of 3/28/2012. [[Pronterface]] is a cross platform printer control program that can be used for testing/printing.<br />
<br />
Working preconfigured '''Sprinter''' firmware can be downloaded here: [[file:UltiMachineRAMPS1-4Sprinter.zip]]. Mechanical is in the folder ending with ME, optical endstop firmware is in the folder ending in OE.<br />
<br />
Working preconfigured '''Marlin''' firmware can be downloaded at<br />
http://adf.ly/1RKUfV . is for mechanical endstops. For optical, you will need to reverse the endstop logic in configuration.h. The language of display is in italian, but can easy be changed in language.h. It is preconfigured for the RepRap Discount Smart Controller and similar LCD module. You will need to disable LCD in configuration.h if not using it.<br />
<br />
Others (Need pins set in Firmware as below):<br />
<br />
*mechanical endstops (now the default ultimachine.com option) require '''#define OPTO_PULLUPS_INTERNAL 1''' to be added to configuration.h if not there by default.<br />
<br />
Here are the pin definitions for this board.<br />
<pre><br />
// For RAMPS 1.4<br />
#define X_STEP_PIN 54<br />
#define X_DIR_PIN 55<br />
#define X_ENABLE_PIN 38<br />
#define X_MIN_PIN 3<br />
#define X_MAX_PIN 2<br />
<br />
#define Y_STEP_PIN 60<br />
#define Y_DIR_PIN 61<br />
#define Y_ENABLE_PIN 56<br />
#define Y_MIN_PIN 14<br />
#define Y_MAX_PIN 15<br />
<br />
#define Z_STEP_PIN 46<br />
#define Z_DIR_PIN 48<br />
#define Z_ENABLE_PIN 62<br />
#define Z_MIN_PIN 18<br />
#define Z_MAX_PIN 19<br />
<br />
#define E_STEP_PIN 26<br />
#define E_DIR_PIN 28<br />
#define E_ENABLE_PIN 24<br />
<br />
#define SDPOWER -1<br />
#define SDSS 53<br />
#define LED_PIN 13<br />
<br />
#define FAN_PIN 9<br />
<br />
#define PS_ON_PIN 12<br />
#define KILL_PIN -1<br />
<br />
#define HEATER_0_PIN 10<br />
#define HEATER_1_PIN 8<br />
#define TEMP_0_PIN 13 // ANALOG NUMBERING<br />
#define TEMP_1_PIN 14 // ANALOG NUMBERING<br />
</pre><br />
<br />
==Source==<br />
<br />
{|class="wikitable" style="margin: 1em auto 1em auto;"<br />
|- style="background-color:#999999;" <br />
! FILE ID#<br />
! TYPE<br />
! DESCRIPTION<br />
! DOWNLOAD<br />
|-<br />
| [[File:ArduinoMegaPololuShield.zip]]<br />
| Eagle Files<br />
| These are the files you need to make the board.(Use the File: link to the left to access older versions of the file.)<br />
| [[media:ArduinoMegaPololuShield.zip]]<br />
|-<br />
|-<br />
| [[File:RepRapjr.lbr]]<br />
| Eagle Libraries<br />
| The components used in this board are here. see [[Eagle_Library]]<br />
| [[media:RepRapjr.lbr]]<br />
|-<br />
|}<br />
<br />
==Bill of Materials==<br />
{| border="1"<br />
|-<br />
! ID<br />
! Description<br />
! Quantity<br />
! Part Number<br />
! Reichelt Order Number<br />
! Digikey Part Number (Description) <br />
|-<br />
| U1<br />
| Arduino Mega or clone<br />
| 1<br />
|2560 or 1280<br />
|<br />
|[http://www.digikey.com/product-detail/en/A000067/1050-1018-ND/2639006 1050-1018-ND](BOARD MCU MEGA2560)<br />
|-<br />
| U2,U3,U4,U5<br />
| [[Pololu stepper driver board]]s or clones<br />
| 4<br />
| A fifth one can be used for a 2nd extruder or extra axis<br />
|<br />
|N/A<br />
|-<br />
| C2<br />
| 100nF capacitor (0805)(> highest planned voltage)<br />
| 1<br />
| <br />
|<br />
|[http://www.digikey.com/product-detail/en/CC0805KRX7R8BB104/311-1141-1-ND/303051 311-1141-1-ND](CAP CER 0.1UF 25V 10% X7R 0805)<br />
|-<br />
| C1,C5,C8<br />
| 10uF capacitor (153CLV-0405)(>5V)<br />
| 3<br />
| <br />
|<br />
|[http://www.digikey.com/product-detail/en/EXV106M025A9BAA/399-6724-1-ND/3082855 399-6724-1-ND](CAP ALUM 10UF 25V 20% SMD)<br />
|-<br />
| C3,C4,C6,C7,C9,C10<br />
| 100uF capacitor (153CLV-0605)(> highest planned voltage)<br />
| 6<br />
|<br />
|<br />
|[http://www.digikey.com/product-detail/en/EXV107M016A9GAA/399-6726-1-ND/3082857 399-6726-1-ND](CAP ALUM 100UF 16V 20% SMD)<br />
|-<br />
| R1,R7,R11,R21,R22<br />
| 4.7K resistor (0805)(1%)<br />
| 5<br />
| <br />
|<br />
|[http://www.digikey.com/scripts/dksearch/dksus.dll?vendor=0&keywords=RHM4.70KAECT-ND+ RHM4.70KAECT-ND](RES 4.70K OHM .4W 1% 0805) <br />
|-<br />
| R2,R3,R4,R5,R6,R8,R9,R10<br />
| 100K resistor (0805)<br />
| 8<br />
| <br />
|<br />
|[http://www.digikey.com/product-detail/en/ESR10EZPF1003/RHM100KAECT-ND/1983806 RHM100KAECT-ND](RES 100K OHM .4W 1% 0805)<br />
|-<br />
| R12<br />
| 1K resistor (0805)<br />
| 1<br />
| <br />
|<br />
|[http://www.digikey.com/product-detail/en/ESR10EZPF1001/RHM1.00KAECT-ND/1983804 RHM1.00KAECT-ND](RES 1.00K OHM .4W 1% 0805)<br />
|- <br />
| R23,R24,R25<br />
| 1.8K resistor (0805)<br />
| 3<br />
|<br />
|<br />
|[http://www.digikey.com/product-detail/en/RC0805FR-071K8L/311-1.80KCRCT-ND/730467 311-1.80KCRCT-ND](RES 1.80K OHM 1/8W 1% 0805)<br />
|-<br />
| R16,R17,R18,R19,R20<br />
| 10K resistor (0805)<br />
| 5<br />
|<br />
|<br />
|[http://www.digikey.com/product-detail/en/ERJ-6ENF1002V/P10.0KCCT-ND/119248 P10.0KCCT-ND](RES 10.0K OHM 1/8W 1% 0805)<br />
|-<br />
| R13,R14,R15<br />
| 10 ohm resistor (0805)<br />
| 3<br />
|<br />
|<br />
|[http://www.digikey.com/product-detail/en/CRCW080510R0FKEAHP/541-10.0TCT-ND/2222835 541-10.0TCT-ND](RES 10.0 OHM .33W 1% 0805)<br />
|-<br />
| Q1,Q2,Q3<br />
| N-channel Mosfet<br />
| 3<br />
| STP55NF06L (<math>R_{DS} = 18 m\Omega</math> On) <br />
Upgrade particularly for the bed:<br />
IRLB8743PBF (<math>R_{DS} = 3.2 m\Omega</math> On) or for even more current<br />
IRLB3034PBF (<math>R_{DS} = 1.5 m\Omega</math> On)<br />
| ZXM 64N035 L3<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=497-6742-5-ND 497-6742-5-ND] (MOSFET N-CH 60V 55A TO-220)<br />
|-<br />
| D1,D2<br />
| Diode<br />
| 2<br />
| 1N4004<br />
| 1N 4004<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=1N4004FSCT-ND 1N4004FSCT-ND] (DIODE GEN PURPOSE 400V 1A DO41)<br />
|-<br />
| F1<br />
| PTC resettable fuse (30V, Hold5A, Trip10A)<br />
| 1<br />
| MF-R500<br />
| PFRA 500<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=MF-R500-ND MF-R500-ND] (FUSE PTC RESETTABLE 5A HOLD)<br />
|-<br />
| F2<br />
| PTC resettable fuse (Hold11A)<br />
| 1<br />
| MF-R1100<br />
| <br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=RGEF1100-ND RGEF1100-ND] (POLYSWITCH RGE SERIES 11.0A HOLD)<br />
|-<br />
| J2<br />
| D8-D10 Outputs // 6 position screw terminal (min 11A per contact) OR Jack/Plug connector pair<br />
| 1<br />
| 282837-6<br />
| AKL 101-06<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=WM7857-ND WM7857-ND] (CONN TERMINAL BLOCK 6POS 5.08MM) <br />
<br />
OR <br />
<br />
[http://www.digikey.com/product-detail/en/phoenix-contact/1935200/277-1581-ND/568618 1935200] (TERM BLOCK PCB 6POS 5.0MM)<br />
<br />
OR <br />
<br />
1x [http://www.digikey.com/product-detail/en/20020109-H061A01LF/609-4284-ND/2509130 609-4284-ND] & 1x [http://www.digikey.com/scripts/DkSearch/dksus.dll?WT.z_header=search_go&lang=en&keywords=609-4218-ND&x=0&y=0&cur=USD 609-4218-ND]. [https://lh6.googleusercontent.com/--1nJttlNQDs/UNfmaLXKiTI/AAAAAAAADxQ/Z6CSD4V8r6I/s617/20121223_194819.jpg May prevent overtemp events] <br />
|-<br />
| LED1<br />
| Green LED (0805)<br />
| 1<br />
|<br />
|<br />
|[http://www.digikey.com/product-detail/en/CMD17-21VGD%2FTR8/L62505CT-ND/254936 L62505CT-ND](LED GREEN DIFF 0805 SMD)<br />
|-<br />
|LED2,LED3,LED4<br />
| Red LED (0805)<br />
| 3<br />
|<br />
|<br />
|[http://www.digikey.com/product-detail/en/CMD17-21VRD%2FTR8/L62501CT-ND/254934 L62501CT-ND](LED HI EFF RED DIFF 0805)<br />
|-<br />
| S1<br />
| Push button switch<br />
| 1<br />
| B3F-3100 <br />
| TASTER 3305B (should fit footprint also, but button will overhang board edge)<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=450-1648-ND 450-1648-ND] (SWITCH TACT RA H=6.35MM)<br />
|-<br />
| X1<br />
| Power jack (Plug and fixed receptacle)(Min 11A per position more is better)<br />
| 1<br />
| MSTBA 2,5 and MSTBT 2,5 (5.04mm spacing 4 connector)<br />
| <br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=WM7847-ND WM7847-ND] (CONN HEADER 4POS 5.08MM R/A TIN) &amp; [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=WM7953-ND WM7953-ND] (CONN TERM BLOCK 4POS 5.08MM R/A)<br />
<br />
OR<br />
<br />
[http://www.digikey.com/product-detail/en/phoenix-contact/1935187/277-1579-ND/568616 1935187] (TERM BLOCK PCB 4POS 5.0MM)<br />
|-<br />
|<br />
| 2 x 3 pin header<br />
| 8<br />
| 961206-6404-AR<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=3M9459-ND 3M9459-ND] (CONN HEADER VERT DUAL 6POS GOLD)<br />
|-<br />
| <br />
| 4 pin header<br />
| 5<br />
| 961104-6404-AR<br />
| SL 1X36G 2,54 (3 of these)<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=3M9449-ND 3M9449-ND] (CONN HEADER VERT SGL 4POS GOLD)<br />
|-<br />
| <br />
| 6 pin header<br />
| 2 (? - from http://gala-automation.com/index.php/component/content/article/26-reprap-tutorials/42-ramps-14-bom)<br />
| 961106-6404-AR<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=3M9451-ND 3M9451-ND] (CONN HEADER VERT SGL 6POS GOLD)<br />
|-<br />
|<br />
| 2 x 18 Pin Stackable Female Header (non stackables can be used with plated through holes)<br />
| 1<br />
| <br />
| MALE: SL 2X25G 2,54 (2 of them, shortened with a saw or pliers)<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7121-ND S7121-ND] (CONN HEADER FMAL 36PS.1" DL GOLD) - Not Stackable<br />
|-<br />
| <br />
| 8 Pin Stackable Female Header (non stackables can be used with plated through holes)<br />
| 5<br />
|<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7041-ND S7041-ND] (CONN HEADER FEMALE 8POS .1" GOLD) - Not Stackable<br />
|-<br />
| <br />
| 6 Pin Stackable Female Header (non stackables can be used with plated through holes)<br />
| 1<br />
|<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7039-ND S7039-ND] (CONN HEADER FEMALE 6POS .1" GOLD) - Not Stackable<br />
|-<br />
| <br />
| 24 Pin Female Header * Note *<br />
| 2<br />
| Required to carry enough current for motors<br />
| <br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7057-ND S7057-ND] (CONN HEADER FMALE 24POS .1" GOLD) - Rated @ 3A / Pin<br />
|-<br />
| <br />
| 8 Pin Female Header * Note *<br />
| 4<br />
| Required to carry enough current for motors<br />
| <br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=S7041-ND S7041-ND] (CONN HEADER FEMALE 8POS .1" GOLD) - Rated @ 3A / Pin<br />
|-<br />
|<br />
| 0.1" Jumpers<br />
| 15<br />
|<br />
|<br />
| [http://search.digikey.com/scripts/DkSearch/dksus.dll?lang=en&site=CA&KeyWords=A26242-ND A26242-ND] (SHUNT LP W/HANDLE 2 POS 30AU)<br />
|-<br />
|<br />
| Circuit Board<br />
|1<br />
|v1.4<br />
|<br />
|N/A<br />
|}<br />
Note * You can use Female Headers which are not the exact size, but they are hard to break/cut so in this case buy some extra! (one wasted header per cut)<br />
<br />
A BOM for sourcing the RAMPS components from Mouser is also available in [https://docs.google.com/spreadsheet/ccc?key=0Auf-66FPv0JidHhtRVB0VVplOURwWklrX0tIeXhsS3c&hl=en_US#gid=0 this google spreadsheet] (This list is incomplete and has missing or incorrect quantities.)<br />
<br />
Shopping lists for v1.4 [http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=d126a71257] .<br />
<br />
= BT Extension =<br />
: ''main article: [[jy-mcu]]''<br />
In order to get rid of the USB connection between RAMPS and the PC, you may like to use Bluetooth. There is a cheap module available in the market called 'JY-MCU' (vendor Shenzhen Jiayuan Electronic Co.,Ltd.).<br />
<br />
[[File:jy-mcu_f.jpg|300px]] [[File:jy-mcu_b.jpg|300px]]<br />
<br />
==Change module setting==<br />
Before the module can be used, the default setting has to be changed. You can connect to and modify the BT JY-MCU module settings via the Arduino mega 2560 using the pin 10 and pin 9 as Rx and Tx terminals, respectively. Make sure you connect Rx on the BT module to the Tx on the arduino and vice versa, in other words Rx goes to Tx and vice versa. Upload the simple code to arduino located on an instructable entitled "Success-Using-the-JY-MCU-linvor-Bluetooth-Module". Use the serial monitor within arduino IDE or another terminal program, with baudrate set to 9600 and 'No Line Ending' selected, enter the following commands: <br />
<br />
AT - the response should be OK (If you see weird characters, the baudrate is wrong--> try a different one<br />
<br />
AT+NAMExxxx - Where xxxx is the friendly name of the module<br />
<br />
AT+BAUDx - Where x sets the baud rate (values & baud rates below)<br />
<br />
AT+VERSION - Returns the firmware version<br />
<br />
AT+PINxxxx - Sets a new pairing code (default: 1234)<br />
<br />
1——1200 <br />
2——2400 <br />
3——4800 <br />
4——9600 <br />
5——19200 <br />
6——38400 <br />
7——57600 <br />
8——115200<br />
<br />
Alternatively, you can connect to the module from PC via USB<->RS232 (RxD/TxD) interface with default settings (9600, N, 8, 1). The module shouldn't be paired at that moment. Use the same AT commands as above.<br />
<br />
More details about the configuration you will find here [[http://reprap.org/wiki/Melzi#Connect_via_Bluetooth]]<br />
<br />
Troubleshooting:<br />
If you see weird characters, the baudrate is wrong--> try a different one<br />
Make sure your Tx and Rx are not mixed up<br />
Make sure you have the proper resistors installed<br />
<br />
==Wiring==<br />
On RAMPS/Arduino Mega the UART level are 5V but the BT module supports only 3.3V input. Therefore the TxD level has to be divided by resistor. This passive solution is fast enough for 115kBaud. Overall only 4 wires have to be soldered. <br />
<br />
[[File:BT_Connection_RAMPS1.4.png|400px]]<br />
<br />
==Connect via Bluetooth==<br />
Once you have setup your BT devices you can select from drop down list and control your RepRap as usual.<br />
<br />
==RAMPS 1.4 test code==<br />
<br />
#define X_STEP_PIN 54<br />
#define X_DIR_PIN 55<br />
#define X_ENABLE_PIN 38<br />
#define X_MIN_PIN 3<br />
#define X_MAX_PIN 2<br />
<br />
#define Y_STEP_PIN 60<br />
#define Y_DIR_PIN 61<br />
#define Y_ENABLE_PIN 56<br />
#define Y_MIN_PIN 14<br />
#define Y_MAX_PIN 15<br />
<br />
#define Z_STEP_PIN 46<br />
#define Z_DIR_PIN 48<br />
#define Z_ENABLE_PIN 62<br />
#define Z_MIN_PIN 18<br />
#define Z_MAX_PIN 19<br />
<br />
#define E_STEP_PIN 26<br />
#define E_DIR_PIN 28<br />
#define E_ENABLE_PIN 24<br />
<br />
#define Q_STEP_PIN 36<br />
#define Q_DIR_PIN 34<br />
#define Q_ENABLE_PIN 30<br />
<br />
#define SDPOWER -1<br />
#define SDSS 53<br />
#define LED_PIN 13<br />
<br />
#define FAN_PIN 9<br />
<br />
#define PS_ON_PIN 12<br />
#define KILL_PIN -1<br />
<br />
#define HEATER_0_PIN 10<br />
#define HEATER_1_PIN 8<br />
#define TEMP_0_PIN 13 // ANALOG NUMBERING<br />
#define TEMP_1_PIN 14 // ANALOG NUMBERING<br />
<br />
void setup() {<br />
pinMode(FAN_PIN , OUTPUT);<br />
pinMode(HEATER_0_PIN , OUTPUT);<br />
pinMode(HEATER_1_PIN , OUTPUT);<br />
pinMode(LED_PIN , OUTPUT);<br />
<br />
pinMode(X_STEP_PIN , OUTPUT);<br />
pinMode(X_DIR_PIN , OUTPUT);<br />
pinMode(X_ENABLE_PIN , OUTPUT);<br />
<br />
pinMode(Y_STEP_PIN , OUTPUT);<br />
pinMode(Y_DIR_PIN , OUTPUT);<br />
pinMode(Y_ENABLE_PIN , OUTPUT);<br />
<br />
pinMode(Z_STEP_PIN , OUTPUT);<br />
pinMode(Z_DIR_PIN , OUTPUT);<br />
pinMode(Z_ENABLE_PIN , OUTPUT);<br />
<br />
pinMode(E_STEP_PIN , OUTPUT);<br />
pinMode(E_DIR_PIN , OUTPUT);<br />
pinMode(E_ENABLE_PIN , OUTPUT);<br />
<br />
pinMode(Q_STEP_PIN , OUTPUT);<br />
pinMode(Q_DIR_PIN , OUTPUT);<br />
pinMode(Q_ENABLE_PIN , OUTPUT);<br />
<br />
digitalWrite(X_ENABLE_PIN , LOW);<br />
digitalWrite(Y_ENABLE_PIN , LOW);<br />
digitalWrite(Z_ENABLE_PIN , LOW);<br />
digitalWrite(E_ENABLE_PIN , LOW);<br />
digitalWrite(Q_ENABLE_PIN , LOW);<br />
}<br />
<br />
void loop () {<br />
<br />
if (millis() %1000 <500) <br />
digitalWrite(LED_PIN, HIGH);<br />
else<br />
digitalWrite(LED_PIN, LOW);<br />
<br />
if (millis() %1000 <300) {<br />
digitalWrite(HEATER_0_PIN, HIGH);<br />
digitalWrite(HEATER_1_PIN, LOW);<br />
digitalWrite(FAN_PIN, LOW);<br />
} else if (millis() %1000 <600) {<br />
digitalWrite(HEATER_0_PIN, LOW);<br />
digitalWrite(HEATER_1_PIN, HIGH);<br />
digitalWrite(FAN_PIN, LOW);<br />
} else {<br />
digitalWrite(HEATER_0_PIN, LOW);<br />
digitalWrite(HEATER_1_PIN, LOW);<br />
digitalWrite(FAN_PIN, HIGH);<br />
}<br />
<br />
if (millis() %10000 <5000) {<br />
digitalWrite(X_DIR_PIN , HIGH);<br />
digitalWrite(Y_DIR_PIN , HIGH);<br />
digitalWrite(Z_DIR_PIN , HIGH);<br />
digitalWrite(E_DIR_PIN , HIGH);<br />
digitalWrite(Q_DIR_PIN , HIGH);<br />
}<br />
else {<br />
digitalWrite(X_DIR_PIN , LOW);<br />
digitalWrite(Y_DIR_PIN , LOW);<br />
digitalWrite(Z_DIR_PIN , LOW);<br />
digitalWrite(E_DIR_PIN , LOW);<br />
digitalWrite(Q_DIR_PIN , LOW);<br />
} <br />
<br />
digitalWrite(X_STEP_PIN , HIGH);<br />
digitalWrite(Y_STEP_PIN , HIGH);<br />
digitalWrite(Z_STEP_PIN , HIGH);<br />
digitalWrite(E_STEP_PIN , HIGH);<br />
digitalWrite(Q_STEP_PIN , HIGH); <br />
delay(1);<br />
<br />
digitalWrite(X_STEP_PIN , LOW);<br />
digitalWrite(Y_STEP_PIN , LOW);<br />
digitalWrite(Z_STEP_PIN , LOW);<br />
digitalWrite(E_STEP_PIN , LOW);<br />
digitalWrite(Q_STEP_PIN , LOW); <br />
}<br />
<br />
=Where to get=<br />
* [http://www.reprap.cc/shop/de/content/ramps-14 Reprap Austria] (worldwide free shipping)<br />
* [http://www.makerfarm.com/index.php/printer-electronics/ramps.html Maker Farm Inc] USA - (worldwide shipping)<br />
* [http://store.thingibox.com/es/electricidad/38-ramps_14.html Thingibox] Spain - (worldwide shipping)<br />
* [https://reprap.pt/pecas/eletronica/ramps-1-4 RepRap.PT] Portugal<br />
* [http://www.reprap.me/electronic/ramps.html RepRap.me Denmark] (worldwide shipping)<br />
* [https://www.tindie.com/products/staticboards/ramps-14-sb-premium/ RAMPS 1.4 Manufactured in Europe with high quality parts for long printing hours] - (worldwide shipping)<br />
* [https://taotac.com/sanpham/ramps/ TaoTac.com]<br />
* [http://www.reprap.cn/ HE3D]<br />
* [http://twelvepro.com/index.php?route=product/product&path=67&product_id=83 Twelvepro]<br />
* [https://www.fabberworld.com/ramps-1-4 Fabberworld]<br />
* [http://aus3d.com.au/printer-parts/printer-electronics/ramps-14 Aus3D]<br />
* [https://www.diy-india.com DIY-India.com] (India)<br />
<br />
=RAMPS 1.4.2=<br />
<br />
[[Image:RAMPS_1.4.2.jpg|800x513px|RAMPS 1.4.2]]<br />
<br />
RAMPS 1.4.2 has minor changes over RAMPS 1.4. The RAMPS 1.4.2 has below enhancements over 1.4<br />
<br />
* Standard blade fuses instead of thermal fuses increasing the heat resilience.<br />
* Current carrying improved by increasing the thickness of the cooper at the PCB from 35 to 70 micro meters.<br />
* Suppression caps added to each end-stop to avoid spurious signals.<br />
* Added an additional connector to XY, E1 and E2 to connect a second stepper motor.<br />
* Connector for external reset added.<br />
* Labeled D8, D9,D10 with Heatbed, Extruder 1 Fan and Extruder 2.<br />
<br />
Eagle CAD files: [https://github.com/GermanRepRap/Ramps-1.4.2 https://github.com/GermanRepRap/Ramps-1.4.2]<br />
<br />
==Where to buy RAMPS 1.4.2==<br />
<br />
<br />
Fully assembled available from [http://www.germanreprap.com German RepRap]<br />
[http://store.thingibox.com/en/electrical/38-ramps_14.html Full assembled and RAMPS-FD] from Thingibox.<br />
<br />
=Modifications, hacks and add-ons=<br />
==Using 24v on RAMPS== <br />
Details can be found on this page [http://reprap.org/wiki/RAMPS_24v http://reprap.org/wiki/RAMPS_24v]<br />
==Adding LEDS to RAMPS==<br />
Details can be found on this page [http://reprap.org/wiki/RAMPS_LEDs http://reprap.org/wiki/RAMPS_LEDs]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=PCB_Heatbed/Aluminium_Bed_Mount_Plate/Borosilicate_glass&diff=181302PCB Heatbed/Aluminium Bed Mount Plate/Borosilicate glass2018-01-17T15:08:15Z<p>Merlucin: /* How to buy */</p>
<hr />
<div>==PCB heat bed==<br />
[[File:PCB Heatbed.jpg|400px]]<br />
<br />
The Prusa designed PCB heat bed is a great addition to your Reprap printer to help your printing platform to be a heated surface perfect for minimizing warping of larger prints.The heating element is on the bottom side. The heating is done by long traces of copper.The top side is solid copper to keep the PCB flat enough. <br />
<br />
==Borosilicate glass== <br />
[[File:Borosilicate glass.jpg|400px]]<br />
<br />
If you want to make your printing platform flat enough, ideal stuff is glass sheet. Borosilicate glass is rated for higher temperatures than normal sheet glass making it a better material for use as a heated bed. After cracking a few sheets of normal glass from rapidly cooling or heating, borosilicate glass will quell your frustrations.<br />
<br />
==Aluminium Plate==<br />
[[File:Aluminum plate.jpg|400px]]<br />
<br />
The Aluminium Bed Mount Plate design is pre-drilled and tapped to mount boltable bushings, the PCB heated print bed, belt standoffs, belt clamps. This mount plate is designed to fit onto a Reprap Prusa Mendel lm8uu 3D printer.<br />
<br />
==Round PCB heatbed for Delta Rostock mini==<br />
[[File:Geeetech roundbed 3.jpg|400px|]]<br />
<br />
Round PCB heatbed is the new product of Geeetech. The heatbed improves print quality, especially when printing ABS by reducing thermal warping. The diameter of the total heatbed is 215mm, and the diameter of the active heated area is 200mm. It’s as the width as 1.6mm. The allow temperature is from room temperature to 120°C. The heatbed can take both 12V and 24V input and the power is 144W. Moreover, it only takes 4 minutes to heat up the heatbed to 110°C.<br />
<br />
<br />
== How to buy ==<br />
<br />
Borosilicate glass sheets are available from several suppliers:<br />
<br />
[http://www.geeetech.com/3d-printer-setmk2aluminium-bed-mount-plateborosilicate-glass-p-659.html 3D printer set-MK2,Aluminium Bed Mount Plate,Borosilicate glass]<br />
<br />
[https://alfa-tech3d.com/en/building-platform-bed/?categories=spare-parts Alfa-Tech3D: MK2B, Borosilicate glass in Several sizes and shapes, Delivered Worldwide] <br /><br />
<br />
[http://www.geeetech.com/round-pcb-heatbed-for-delta-rostock-mini-p-856.html Round PCB heatbed for Delta Rostock mini]<br />
<br />
[https://www.lulzbot.com/products/borosilicate-glass-bed Lulzbot: borosilicate glass bed sheet].<br />
<br />
[http://airwolf3d.com/shop/borosilicate-glass-plate-for-3d-printer-v-203 Airwolf3D: borosilicate glass plate (214 mm x 200 mm)].<br />
<br />
[http://airwolf3d.com/shop/borosilicate-glass-plate-for-3d-printer-hd-xl-219 Airwolf3D: borosilicate glass plate (214 mm x 307 mm x 3mm)].<br />
<br />
[http://www.mcmaster.com/#catalog/119/3616/=zd4hy8 McMaster-Carr: borosilicate glass sheets in many sizes and thicknesses up to 3/4 inch thick].<br />
(suggested by [http://wanhaousa.com/pages/adding-a-glass-build-plate Wanhao USA]).<br />
<br />
[http://www.voxelfactory.com/collections/hardware/products/custom-cut-borosilicate-glass Voxel Factory: Custom cut borosilicate glass for any 3D Printer] supplies custom borosilicate glass sheets 3.3mm thick in any size.<br />
<br />
[http://www.cgindustrialglass.com/borosilicate-glass.php Cincinnati Gasket & Industrial Glass: Borosilicate Glass] apparently supplies custom borosilicate glass sheets in any size.<br />
<br />
[http://store.thingibox.com/en/temperature/230-heated_bed_glass.html#/type-200_x_204_x_3mm Heated bed glass (200x204x3mm and 200x300x3mm)] from Thingibox.<br />
<br />
<br />
[[Category:Heated Bed]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=PCB_Heatbed&diff=181300PCB Heatbed2018-01-17T14:58:29Z<p>Merlucin: /* Where to get it */</p>
<hr />
<div>{{Languages}}<br />
<br />
{{Development<br />
|description = PCB Heatbed<br />
|status = working<br />
|author = Josef Průša<br />
|reprap = mendel/darwin/repstraps<br />
|cadModel = [[http://www.thingiverse.com/thing:3919]]<br />
|categories = {{tag|Heated Bed}}<br />
|image = PCB_HEATBED.jpg<br />
|url = http://josefprusa.cz/pcb-heatbed-final-mounting-and-wiring-solutio<br />
}}<br />
<br />
==WARNING==<br />
<span style="color:red;>"'''WARNING!!!'''<br />
Be careful where you buy PCB heatbeds from!!<br />
There is one very important requirement - the heatbed must be etched directly from 35um copper clad! ASK YOUR SELLER!!!<br />
If the board is plated, as it's normally done, the manufacturer cannot guarantee the final thickness of copper or the evenness of the copper around the board.<br />
If it is uneven, the heat won't be evenly distributed around the board or the board won't have a high enough heat output overall. <br />
<br />
'''Your biggest warning sign is plated holes! Plating of holes requires copper plating.'''<br />
<br />
</span><br />
<br />
==About==<br />
<br />
The original PCB Heatbed MK1 was developed by [[User:Prusajr | Josef Průša]].<br />
<br />
* 200 mm x 200 mm active heated area.<br />
* 209 mm center-to-center mounting holes (outside the active area).<br />
* 214 mm x 214 mm total PCB size.<br />
<br />
"I was working on this idea for nearly six months, inspired by [http://neufeld.newton.ks.us/electronics/?p=864 neufeld.newton.ks.us/electronics/?p=864]".<br />
<br />
==Where to get it==<br />
[[Category:Suppliers_by_Part]]<br />
<br />
The .brd file is available here: [[http://www.thingiverse.com/thing:3919]]<br />
<br />
Mechanical drawings for designing mounting plates/etc (if desired) are here: [[http://www.thingiverse.com/thing:21271]]<br />
<br />
(Please note that I dont get any provision from these :-))<br />
Manufactured PCBs can be found here:<br />
<br />
Refer to the [[RepRap_Buyers%27_Guide]]<br />
[[http://www.reprap.cn/heat-bed-c-19/]]<br />
<br />
==Printing==<br />
<br />
Previously the accepted method was to cover the PCB heatbed with kapton tape, degrease it and print.<br />
An alternative method that has become popular (as of January 2015) is to use a sheet of 3mm borosilicate glass, held using bulldog clips (see the Discussion tab). Adherence of the printed object to the glass is helped by spraying the clean glass with hair lacquer (the "extra strength" type).<br />
<br />
ABS temperature range: 100-110°C<br />
<br />
PLA temperature range: 50-70°C<br />
<br />
These ranges of temperatures are indicative only, you'll have to test and see what works best for your printer/filament/hotend setup.<br />
<br />
MAKE SURE YOUR [[Power Supply]] HAS 10 MORE AMPS SPARE!!!<br />
<br />
==Mounting==<br />
<br />
Known working solution, I (prusajr) use is Glass sheet (3mm) with glued on cork standoffs and on top of that is glued the heatbed.<br />
http://www.flickr.com/photos/prusajr/5410919911/<br />
http://www.flickr.com/photos/prusajr/5410919707/<br />
<br />
When mounted only using the four corners, the inherent warp of the pcb can be a problem, hence it is better to use the cork mounting system above (as the piece of cork in the centre helps to keep the pcb flat).<br />
Magnets can be used in replace of the cork, this makes the bed removable. However, I (mooneyj) have only tried this on a darwin type printer (where the build platform only moves in z). During fast printing, the darwin vibrates and it seems the heatbed magnets slide over each other slightly. The acceleration of the y axis on a mendel may cause the magnets to slide also. Perhaps a hybrid of magnet and bolt mounting would work well?.<br />
<br />
'''The current standard (as of January 2015)''', however, is to simply place a square (200mm x 200mm) piece of glass on top of the heatbed, and affix it on the four sides with bulldog clips. The clips will not melt under pressure, and sufficiently hold the glass to the bed. This makes removal easier for cleaning as well.<br />
<br />
[[File:Heatbed_glass_clips_1a.jpg|600px|PCB heatbed mounted on P3Steel (Prusa i3 variant) with glass and bulldog clips.]]<br />
<br />
==Sides==<br />
<br />
The PCB heatbed has two sides, one with the copper traces (bottom side) and one without (top). On older versions of the PCB heatbed only the side without traces carried a silkscreen. Currently (as of January 2015) PCB heatbeds are silkscreened on both sides.<br />
<br />
Previously, printing on the top side was considered to be safer as the copper traces could be damaged if the print head would collide with the heatbed surface (if for example the Z-min endstop malfunctioned). Obviously if a piece of glass is used as the print surface, it protects the PCB copper traces. However, make sure your heatbed mounting springs are not too strong to prevent damage to the glass in case of an accidental collision.<br />
<br />
Note that the LED, resistor and wire connections are also liable to accidentally collide with the print head.<br />
<br />
Again, '''the current standard (as of January 2015)''' when the PCB heatbed is used with a piece of glass as the build surface '''is to mount the PCB heatbed with the traces up'''. This improves heat transfer to the glass and the PCB heats up faster.<br />
<br />
[[File:PCB_HEATBED.jpg]]<br />
<br />
==Connection==<br />
<br />
<br />
===Optional LEDs===<br />
<br />
The LEDs are optional, but if you choose to use the LEDs you MUST install the resistor.<br />
<br />
''''Parts''''<br />
<br />
2 x Surface Mount LEDs<br />
<br />
1 x 1K ohm Surface Mount Resistor<br />
<br />
<br />
<br />
Mount the LEDs in different directions (polarity) so that one of the LEDs will light up regardless of the board's polarity. You can use a single LED if you are certain of the polarity.<br />
<br />
[[File:PCB_HEATBED_DIAGRAM_r.jpg]]<br />
<br />
===Electronics===<br />
''RAMPS''<br />
<br />
See [[RAMPS1.4]], [[RAMPS1.3]], or [[RAMPS1.2]] depending on your version.<br />
<br />
''Sanguinolou''<br />
The MK2 PCB heatbed heats up to 110C when powered through the heated bed connection on Sanguinolou. Your power supply should be 300W and you should ensure that the wires from your power supply to the Sanguinolou are capable of handling the total draw of 20A+. Using a 300W ATX power supply with the 4wire ATX dual 12V connector is working well for me.<br />
<br />
N.B. It is recommended that you use a heatsink on your heated bed mosfet, it will get hot!<br />
<br />
N.B. It is recommended that you measure the resistance of your board. I (evilB) didn't and blew up my Ramps 1.2 MOSFET because of a too high current. My measured resistance was 0.8 Ohm.<br />
<br />
==Troubleshooting==<br />
<br />
The heatbed is often the source of various problems in RepRap 3D printers. The following is a list of possible problems and how to correctly diagnose their cause and possible solutions:<br />
<br />
<br />
'''T1) As soon as the PCB heatbed is turned on, my power supply switches off.'''<br />
<br />
: '''D1)''' Check that your power supply can effectively supply 12V @ 15A or more. If you are using an old PC power supply, it may not be able to provide the required current, or it could need a balancing resistor.<br />
<br />
:: '''S1)''' Use a better power supply. See [[Choosing a Power Supply for your RepRap]].<br />
<br />
<br />
'''T2) My PCB heatbed never reaches the required temperature, or takes too long to reach the required temperature'''.<br />
<br />
This is probably the most common problem with heatbeds that RepRap builders have to deal with. It can have various causes:<br />
<br />
: '''D2a)''' Turn off your printer completely, and measure the resistance of your heatbed using a multimeter: it should not be higher than 1.2 Ohm. If it is higher than 1.2 Ohm, your heatbed will not get enough current and will not dissipate enough heat to reach the required temperatures.<br />
<br />
:: '''S2a)''' Return the heatbed to whomever sold it to you and make sure to get one with a proper resistance!<br />
<br />
: '''D2b)''' If you have measured the resistance of your PCB heatbed and it is lower than 1.2 Ohm, you need to check the voltage across the heatbed terminals when it is heating up. If the voltage is significantly below, say, 11.7V, then again your heatbed will not get enough current and will not dissipate enough heat to reach the required temperatures.<br />
<br />
:: '''S2b)''' Make sure you are using electrical cable with a proper gauge (14 gauge recommended) to connect the heatbed to the controller board. And again, make sure your power supply provides the proper voltage under load conditions. Change components as required.<br />
<br />
: '''D2c)''' Make sure you have the PCB traces on the upper side of your heatbed!<br />
<br />
:: '''S2c)''' Flip the PCB heatbed if required.<br />
<br />
<br />
'''T3) I have checked the temperature on the PCB heatbed and it does not provide uniform heating.'''.<br />
<br />
: '''D3)''' This is actually quite common and not a very serious problem as long as the variation in temperature is below +/- 3C between center and periphery. The corners will always be a little cooler, too.<br />
<br />
:: '''S3)''' Check the various PCB insulation methods listed below. They will minimize heat losses from the underside of the PCB.<br />
<br />
<br />
The following video shows a PCB heatbed MK2 being heated to 60 degrees as seen by an infrared camera:<br />
<videoflash>QE90bDUaAno</videoflash><br />
<br />
==Thermal insulation==<br />
<br />
It's a good idea to insulate the underside of the heatbed in order to get a faster heat up time and a overall better thermal performance. For higher temperatures, an insulation might even be required.<br />
<br />
[[File:Thermal_Isolation.png | thumb | 300px | right | Cork plate cut to fit under a PCB heated bed.]] <br />
<br />
Solutions found to work are:<br />
<br />
* Cork plate.<br />
* Cotton batting.<br />
* Wool felt sheet.<br />
* Rescue sheet, see e.g. [[Robert's Heated Bed]] ie the silver or gold rescue blanket used by hikers.<br />
* Glass fibre soldering/plumbers/welding mat<br />
* Silicon or teflon cooking sheet<br />
<br />
{{Clear}}<br />
<br />
== FORKS (not done by Prusa)==<br />
<br />
=== MK2, MK2a ===<br />
<br />
It's not successor of MK1 even with it's name. It's concurrent design. - Josef Prusa<br />
<br />
MK2a Heatbed with minor changes by Tony from [http://www.think3dprint3d.com/ Think3dPrint3d]<br />
<br />
==== About the MK2a ====<br />
<br />
I liked Josef's original design but wanted to be able to use through hole components, have the thermistor poke through the middle and for it to look good on the 'back' with the silkscreen that Josef designed on that side as well.<br />
<br />
The MK2a has a few further changes:<br />
<br />
* A mounting hole in the middle of one edge to allow for easier bed levelling, thanks to [http://hydraraptor.blogspot.com/2012/05/bed-levelling.html Nophead] for this suggestion.<br />
* Larger LED and Resistor pads to allow for 1206 size surface mount components.<br />
* Much larger area to solder the current carrying wire, easily connect ribbon cable (such as with the Mendel90 heatbed connection). Also the through holes increased in size.<br />
* The redundant pads on the non-heating element side of the board removed to prevent confusion. These are not electrically connected if the board is not plated (plated boards are bad for the reasons outlined by Josef Prusa above).<br />
<br />
==== Further update of the MK2a ====<br />
(by Tony from [http://www.think3dprint3d.com/ Think3dPrint3d])<br />
<br />
In order to make ribbon cable easier to use we have made the following changes:<br />
<br />
Holes in the extended solder pads<br />
<br />
[[File:MK2a-header_holes.jpg | 600px]]<br />
<br />
This allows for IDC compatible pin headers to be used <br />
<br />
[[File:MK2a-headers.jpg | 600px]]<br />
<br />
This in turn makes plugging in a heated bed wiring loom very easy<br />
<br />
[[File:MK2a-headers_connectors.jpg | 600px]]<br />
<br />
==== Where to get it ====<br />
<br />
The MK2 .brd file is available here: [[File:PCB_heatedbed_Mk2.brd]][[http://www.reprap.cn/free-shipping-the-reprap-3d-printer-heating-bed-pcb-heatbed-mk2b-p-53.html?cPath=19]]<br />
<br />
The MK2a .brd file is available here [[File:PCB_heatedbed_Mk2a.brd]]<br />
<br />
Manufactured MK2 PCBs can be found here:<br />
<br />
[http://www.robotdigg.com/product/99 MK2B From RobotDigg (CN) ]<br />
<br />
[http://www.easyreprap.com/#!product/prd1/2114060485/easy-reprap-dual-power-mk2b-heat-bed MK2B From Easy RepRap (USA) ]<br />
<br />
[https://taotac.com/sanpham/pcb-heatbed/ MK2A, MK2B, MK3 - TaoTac.com VN]<br />
<br />
[http://twelvepro.com/index.php?route=product/product&path=67&product_id=77 MK2B Dual power 12/24V US]<br />
<br />
[https://alfa-tech3d.com/da/ Alfa-Tech3D MK2B (DK, Worldwide)]<br />
<br />
[http://www.think3dprint3d.com/Electronics/PCB-Heatbed-MK2a Think3dPrint3d (UK, Worldwide)]<br />
<br />
[http://www.3distributed.com/products/mk2-heated-bed-1 http://www.3distributed.com/products/mk2-heated-bed-1]<br />
<br />
[http://www.charlies3dtechnologies.com/webshop Charlie's 3D Technologies]<br />
<br />
[http://gadgets3d.com/index.php?route=product/product&product_id=59 www.gadgets3d.com]<br />
<br />
[http://reprap.me/electronics/reprap-pcb-heatbed-mk2.html www.RepRap.me]<br />
<br />
[https://www.rp3d.com/shop/electronics-c-8_14.html rp3d.com]<br />
<br />
[http://stores.ebay.ca/botechengineeringpcbservice Botech Circuits MK2a]<br />
<br />
[http://www.ebay.co.uk/sch/i.html?_nkw=heatbed+reprap+MK2a&_sacat=See-All-Categories#ptm eBay MK2a]<br />
<br />
[http://www.emakershop.com/browse/listing?l=126 eMakerShop MK2a]<br />
<br />
[http://store.thingibox.com/en/temperature/30-heated_bed_rectangluar.html MK2a, MK2b (214x214mm, 314x214mm and 326x326mm) from ThingiBOX]<br />
<br />
[http://stores.ebay.com/reprapdiscount Reprapdiscount MK2 and MK2a eBay]<br />
<br />
[http://www.paoparts.com/fr/200-plaque-chauffante-mk2a.html Paoparts (fr) MK2a]<br />
<br />
[http://www.cubic-print.com/PCB-heated-bed-MK2 Cubic Print (Germany)]<br />
<br />
[http://www.uw3dprinter.nl/en/heatbed-mk2.html Uw3Dprinter.nl MK2 (NL,BE,DE,FR)]<br />
<br />
[http://www.createc3d.com CREATEC 3D (ES, Worldwide)]<br />
<br />
[http://impresoras3dlowcost.com/62-cama-caliente-heatbed-mk2b.html i3Dlc MK2B (SPAIN)]<br />
<br />
[http://nioz.ru/index.php/komplektuyushchie/dlya-3d-printera/mk2b-detail MK2B (RU)]<br />
<br />
[http://reprapworld.com/?products_details&products_id/358/cPath/1645 RepRapWorld]<br />
<br />
[http://www.reprap.pt/pecas/sistema-quente/mesa-aquecida-mk2b RepRap Portugal] MK2B Red and Black<br />
<br />
[http://opensourcehardware.it/en/cerca?controller=search&orderby=position&orderway=desc&search_query=heatbed+&submit_search= opensourcehardware.it (MK2B, MK3-ALU, MK3 300x200)]<br />
<br />
[http://www.hta3d.com/Cama-Caliente www.hta3d.com (MK2A 300x200, MK2B, MK3-ALU, Borosilicate tempered glass and more!!)]<br />
<br />
[http://orballoprinting.com/en/electronics/21-hotbed-mk2b.html orballoprinting.com MK3 MK2B wolrdwide shipping]<br />
<br />
==== Printing ====<br />
'''MK2'''<br />
<br />
Although you can print directly to the bed covered in polyimide tape, no PCB is perfectly flat. It is recommended that you follow the directions in mounting, below, for better results.<br />
<br />
==== Mounting ====<br />
'''MK2'''<br />
<br />
The MK2 board can be mounted either side up and is designed to be mounted as Josef describes:<br />
<br />
http://josefprusa.cz/pcb-heatbed-final-mounting-and-wiring-solutio<br />
<br />
The holes in the 4 corners to attach the heated bed MK2 to the top print plate are not suitable for M3 bolts though! Use M2.5 instead.<br />
<br />
The glass protects the tracks from a head crash and is easily swapped out.<br />
<br />
The board dimensions are identical to the MK1 design.<br />
<br />
Insulation between the board and the thick plate should improve heat-up times and reduce energy consumption. An example is here:<br />
<br />
http://reprap.org/wiki/Mendel_heated_bed#Thermal_Insulation<br />
<br />
''Caution, I have not tried this with the temperatures that the PCB bed can reach!''<br />
<br />
'''MK2a'''<br />
<br />
The MK2a has a central mounting hole on the front side to allow for three point mounting. This is much easier for bed leveling in comparison to 4 point mounting. First level the side with two holes and fix in place, then level the side with one hole. A glass plate is highly recommended to provide a truly flat surface and rigidity.<br />
<br />
[[File:Mk2a_Central_Mount_Point.jpg |200 px]]<br />
<br />
====Sides====<br />
'''MK2'''<br />
<br />
The PCB still has a side with the traces on and a side without but now the silkscreen is on both the top and bottom, this makes it look good even when 'upside down' under a layer of glass. The LED, resistor and power wires can be mounted on either side of the board, with either surface mount or through hole components. If you are using through hole be careful when soldering not to interfere with the glass and introduce a gap between the glass and the PCB. If the MK2 board is made properly without copper plating then be sure to only solder the LED and resistor to the same side and the tracks. This problem is solved in the MK2a by removing the pads on the non connected side.<br />
<br />
MK2<br />
[[File:PCB_Heatbed_MK2_front_small.jpg| 400px]]<br />
<br />
<br />
MK2a<br />
[[File:Mk2a.jpg| 400px]]<br />
<br />
<br />
MK2b Dual Power<br />
[[File:RRD-Mk2b-dual-power.jpg| 400px]][[File:RRD-Mk2b-dual-power_blk.jpg| 445px]]<br />
<br />
There is a central hole in the board and it is sized so a small thermistor<br />
(for example the EPCOS one: http://uk.farnell.com/jsp/search/productdetail.jsp?CMP=i-ddd7-00001003&sku=3878697 ) will fit though it allowing contact directly with the glass.<br />
''todo: test efficacy of using heat sink compound to better thermally couple the thermistor to the glass''<br />
<br />
[[File:PCB_Heatbed_MK2_therm_hole.jpg| 200px]]<br />
<br />
====Connection====<br />
Polarity doesn't affect the PCB, however the LEDs have a polarity.<br />
<br />
'''MK2'''<br />
<br />
There are pads and un-plated through holes for connecting the power wires. Ensure that the wire you use is thick enough for 10A, and solder it to the pads on the track side of the PCB. It is a good idea to think about strain relief so your moving build platform does not flex the joint, this can lead to failure of the joint over time. I recommend routing the wire from the heated bed to strain relief on the thick sheet before routing it to your controller/power supply. ''todo: get pictures of strain relief''<br />
<br />
'''MK2a'''<br />
<br />
The pads to solder onto have been greatly increased as shown in the picture below. The picture shows the wires prepared for soldering routed through the holes for extra security. This does not remove the need to use proper strain relief.<br />
<br />
[[File:Mk2a_Through_Hole.jpg|400 px]]<br />
<br />
'''MK2b Dual Power'''<br />
<br />
As you can see in the pictures below depending on the voltage you want to use you have to use different solder pads, but it's written on the PCB which pads have to be used for which voltage.<br />
<br />
[[File:RRD-Mk2b-dual-power-table.jpg|400px]] [[File:RRD-Mk2b-dual-power-connector_red_blk.jpg|400px]]<br />
<br />
'''MK2i'''<br />
The MK2i is connected just like the MK2a heatbed.<br />
<br />
=====Optional LEDs=====<br />
'''MK2'''<br />
<br />
The LEDs are optional, but if you choose to use the LEDs you MUST install the resistor. Solder the components to the pads on the track side of the PCB. With the MK2, conventional wired parts can be substituted for the surface mount parts. If your MK2 board is made properly without copper plating then be sure to only solder the LED and resistor to the same side and the tracks. This problem is solved in the MK2a by removing the pads on the non connected side.<br />
<br />
<br />
''''Parts''''<br />
<br />
2 x surface mount (0805 size on the MK1 and MK2, 1206 size on the MK2a for easier soldering) or conventional through-hole LEDs. Install with opposite polarity so one or the other will light up regardless of the polarity of the power supply to the board.<br />
<br />
1 x 1K ohm surface mount or through-hole resistor<br />
<br />
=== MK2b Dual Power Technical Details===<br />
You can find the open source files here: http://forum.reprapdiscount.com/forums/oss/<br />
<br />
* Dimensions 214mmx 214mm<br />
* Laminate FR4 1.6+-0.15mm<br />
* 2 layer, 35μm copper<br />
* Red Soldermask - both sides<br />
* White Silkscreen - both sides<br />
* Power Input: 12V or 24v<br />
* copper plated holes<br />
* resistance between 1.0-1.2 ohm (12V) or 3-3.4 ohm (24V) (Sainsmart board came in at 1.8 ohm @ 12V/3.6 ohm @ 24V)<br />
<br />
=== MK2i ===<br />
[[File:IMG_8284_smnocopy.png|400px]]<br />
[[File:IMG_8271_smnocopy.png|400px]]<br />
<br />
The MK2i is a hybrid of MK2a and MK3 designs. It supports 4-point and 3-point mounting. There is a central hole in the PCB for a through hole thermistor such as EPCOS. There are also pads on top and bottom for an SMD or through-hole thermistor. The pads are on the top/bottom (in the center of the PCB, next to the hole) but the thermistor trace is on the top copper and routes again to the bottom for easier wiring, labelled "NTC". This design is versatile and much less tape is needed for strain relief on the thermistor wires.<br />
<br />
The MK2i also sports an internationalized stencil on top and bottom. The stencil has new international symbols for "hot" and "hot - do not touch", as well as translations in English, Spanish, French, and German. The original CAD file also had translations in Chinese, Russian, Arabic, and Japanese - but it fails to export these character sets so they aren't in the final version.<br />
<br />
The code is at [https://github.com/Terawatt-Industries/mk2i https://github.com/Terawatt-Industries/mk2i] and comes with a LBR library file. You should be able to have PCBs made from the MK2i Gerbers. It's probably feasible to make this by hand - as much as an MK2a PCB - except in this case you must have bottom and top layers if you want the thermistor wiring feature.<br />
<br />
== MK2 A4 ==<br />
<br />
This is [[Clone_Wars:_Othon | my build]]. I always wanted a big bed, in order to be able to plot (yes, actually plot, with artistic purpouses) at least DIN A4 in size. So I built my prusa mendel big enough to be able to host such a HBP PCB. I'm no good with any PCB editor, so I made my files in a CAD program, and exported the result file into a dxf file. The file has several layers the names of which should make the information self understandable. Anyway I'll tell: the layers with number names represent the routing of the traces the width of which is the layer's name in mm. The design was basically copied from MK2a. The engineering was made with an evolutive algorithm developed by [[Clone_Wars:_Othon | Damrod]] in [http://www.grasshopper3d.com/ grasshopper]. The manufacturing was a bit faulty, but it works flawlessly.<br />
<br />
* Dimensions 215mmx 315mm<br />
* 1 layer 35μm copper<br />
* resistance between 1.0 and 1.2 ohm<br />
<br />
[[File:Big_Heatbed.JPG|600 px]]<br />
<br />
[https://dl.dropboxusercontent.com/u/6334877/PCB%20HBP%20A4/gerber.zip source gerber]<br />
[https://dl.dropboxusercontent.com/u/6334877/PCB%20HBP%20A4/Mi%20HBP2.dxf source dxf]<br />
<br />
== PCB Heatbed 200X300mm ==<br />
<br />
<br />
<br />
[[file:200X300.jpg|600 px]]<br />
[[file:200X300-TOP.jpg|600 px]]<br />
<br />
The PCB Heatbed 200X300mm has a 100mm bigger built area then the regular MK2 heatbed and the overall outline is 214X314mm.<br />
<br />
It has dual power mode optimized for 12 or 24V but you can also use everything in between (16V, 19V what have you)<br />
(Your printer controller will regulate the power to the heatbed in order to get your preset temperature.)<br />
<br />
The core is regular 1.6mm FR4 PCB and the print surface is the same as regular heatbeds but with a metric ruler grid. <br />
<br />
The connections to the heatbed is the same as the connections on the MK3 Alu. heatbed belov.<br />
<br />
The PCB Heatbed 200X300mm is now available in the [http://reprap.me/ RepRap.me] webshop. <br />
<br />
* Dimensions 214mm x 314mm<br />
* 1 layer 35μm (1oz base) copper<br />
* Resistance between 1 and 1.3 ohm for the 12V<br />
* Resistance between 4.5 and 5 ohm for the 24V<br />
* 110 degrees Celsius possible for both 12V and 24V<br />
* Running 24V on the 12V terminals will heatup the heatbed to 100 degree in only 2 minutes<br />
* 180 degree Celsius max. temperature<br />
<br />
== MK3 ALU-Heatbed Dual Power ==<br />
<br />
The [http://reprap.me/Alu-Heatbed-MK3 Alu-Heatbed MK3] have features similar to MK2 and you can also operate this board with 12V or 24V.<br><br />
<br />
- Heatbed with 3.2mm Aluminum Core. Print directly on the heatbed, no need for glass plate. It's a much lighter solution than PCB heatbed + glass, which makes it better for faster prints.<br><br />
- Dual power supply. Operate at 12V or 24V. You can use thinner wires when operating at 24V.<br><br />
- A central mounting hole on the front side to allow for three point mounting. This is much easier for bed leveling in comparison to 4 point mounting. First level the side with two holes and fix in place, then level the side with one hole.<br><br />
- Large solder pads for multiple wires (ribbon cable) or a SMD pinhead connector can be mounted.<br><br />
- Pads for SMD thermistor 1206<br><br />
<br />
* Dimensions 214mm x 214mm<br />
* 1 layer 35μm (1oz base) copper<br />
* Resistance between 1.4 and 1.6 ohm for the 12V<br />
* Resistance between 5.0 and 5.4 ohm for the 24V<br />
* 100 degree Celsius possible for both 12V and 24V<br />
* With 15V on the 12V terminals will maintain approx. 115 degree Celsius without regulation<br />
* Running 24V on the 12V terminals will heatup the heatbed to 100 degree in only 2 minutes (Your printer controller will regulate the power to the heatbed in order to get your preset temperature.)<br />
* 180 degree Celsius max. temperature<br />
<br />
[[File:alu_heatbed.JPG|600 px]]<br />
''' Bottom side (Do not print directly on this side)'''<br />
<br />
[[file:Alu TOP .jpg|600 px]]<br />
''' Top side (Printing side) '''<br />
<br />
[[File:Alu 12V small.jpg|300 px]]<br />
[[File:Alu 24V small.jpg|300 px]]<br />
<br />
When connecting the heatbed in the 12V setting it is important that you connect solder pad 2 and 3 directly on the heatbed. <br />
<br />
Recommended NTC: EPCOS - B57621C104J62 - THERMISTOR, 100K "or whatever [[thermistor]] you normally use."<br />
<br />
==== Where to get it ====<br />
<br />
[https://alfa-tech3d.com/en/building-platform-bed/heat-bed-mk2b-dual-power-prusa-resistor-and-leds-soldered.html Alfa-Tech3D] <br /><br />
[http://reprap.me/electronics/alu-reprap-heater-board-mk3.html www.RepRap.me]<br /><br />
[http://www.cubic-print.com/MK3-aluminum www.cubic-print.de]<br /> (Cubic-Print currently only offers the version of the bed thats needs a wired thermistor. The SMD pads are solely for SMD LEDs and their resistor.)<br /><br />
[https://taotac.com/sanpham/pcb-heatbed/ TaoTac.com]<br />
<br />
[http://store.thingibox.com/en/temperature/30-heated_bed_rectangluar.html MK3 (214x214mm and 314x214mm) from ThingiBOX]<br />
<br />
[http://www.robotdigg.com/product/202/MK3-Dual-Power-ALU-Heatbed RobotDigg]<br />
<br />
[http://aus3d.com.au/printer-parts/printer-bed Aus3D]<br />
<br />
[http://www.reprap.cn/free-shipping-the-reprap-3d-printer-heating-bed-pcb-heatbed-mk2b-p-53.html Free shipping $13]<br />
<br />
[http://www.geeetech.com/mk2b-heated-bed-prusa-soldered-resistorleds-for-reprap-mendel-p-802.html MK2A]<br />
<br />
[http://www.reprap.cn/free-shipping-prusa-i3-heat-bed-mk3-p-96.html?cPath=19 MK3]<br />
<br />
[https://reprap.pt/pecas/mesas-heated-bed RepRap.pt Heated Beds]<br />
<br />
== MK2a layout in SVG-format ==<br />
<br />
There's an SVG-version (Inkscape) of the MK2a-layout.<br />
<br />
For the toner transfer method and people that only have a printer for letter/DIN A4 there's a version with two separated parts.<br />
Because the parts only have few electrical contacts between them, they easily can be ironed next to each other, fixing the needed bridges with etch resistant paint before etching.<br />
<br />
<gallery><br />
File:Layout_Heatbed_MK2a.svg|MK2A in SVG<br />
File:Layout_Heatbed_RK1_parts_a_b.svg|Printer friendly Part I<br />
File:Layout_Heatbed_RK1_parts_c_d.svg|Printer friendly Part II<br />
File:All_breaches_fixed.JPG|Toner transfered and ready to etch<br />
File:Etched and ready.JPG|The etched board<br />
</gallery><br />
<br />
(You may follow the complete process here: [[Etched_heatbed_construction]])</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=PCB_Heatbed&diff=181299PCB Heatbed2018-01-17T14:48:40Z<p>Merlucin: /* Where to get it */</p>
<hr />
<div>{{Languages}}<br />
<br />
{{Development<br />
|description = PCB Heatbed<br />
|status = working<br />
|author = Josef Průša<br />
|reprap = mendel/darwin/repstraps<br />
|cadModel = [[http://www.thingiverse.com/thing:3919]]<br />
|categories = {{tag|Heated Bed}}<br />
|image = PCB_HEATBED.jpg<br />
|url = http://josefprusa.cz/pcb-heatbed-final-mounting-and-wiring-solutio<br />
}}<br />
<br />
==WARNING==<br />
<span style="color:red;>"'''WARNING!!!'''<br />
Be careful where you buy PCB heatbeds from!!<br />
There is one very important requirement - the heatbed must be etched directly from 35um copper clad! ASK YOUR SELLER!!!<br />
If the board is plated, as it's normally done, the manufacturer cannot guarantee the final thickness of copper or the evenness of the copper around the board.<br />
If it is uneven, the heat won't be evenly distributed around the board or the board won't have a high enough heat output overall. <br />
<br />
'''Your biggest warning sign is plated holes! Plating of holes requires copper plating.'''<br />
<br />
</span><br />
<br />
==About==<br />
<br />
The original PCB Heatbed MK1 was developed by [[User:Prusajr | Josef Průša]].<br />
<br />
* 200 mm x 200 mm active heated area.<br />
* 209 mm center-to-center mounting holes (outside the active area).<br />
* 214 mm x 214 mm total PCB size.<br />
<br />
"I was working on this idea for nearly six months, inspired by [http://neufeld.newton.ks.us/electronics/?p=864 neufeld.newton.ks.us/electronics/?p=864]".<br />
<br />
==Where to get it==<br />
[[Category:Suppliers_by_Part]]<br />
<br />
The .brd file is available here: [[http://www.thingiverse.com/thing:3919]]<br />
<br />
Mechanical drawings for designing mounting plates/etc (if desired) are here: [[http://www.thingiverse.com/thing:21271]]<br />
<br />
(Please note that I dont get any provision from these :-))<br />
Manufactured PCBs can be found here:<br />
<br />
Refer to the [[RepRap_Buyers%27_Guide]]<br />
[[http://www.reprap.cn/heat-bed-c-19/]]<br />
<br />
==Printing==<br />
<br />
Previously the accepted method was to cover the PCB heatbed with kapton tape, degrease it and print.<br />
An alternative method that has become popular (as of January 2015) is to use a sheet of 3mm borosilicate glass, held using bulldog clips (see the Discussion tab). Adherence of the printed object to the glass is helped by spraying the clean glass with hair lacquer (the "extra strength" type).<br />
<br />
ABS temperature range: 100-110°C<br />
<br />
PLA temperature range: 50-70°C<br />
<br />
These ranges of temperatures are indicative only, you'll have to test and see what works best for your printer/filament/hotend setup.<br />
<br />
MAKE SURE YOUR [[Power Supply]] HAS 10 MORE AMPS SPARE!!!<br />
<br />
==Mounting==<br />
<br />
Known working solution, I (prusajr) use is Glass sheet (3mm) with glued on cork standoffs and on top of that is glued the heatbed.<br />
http://www.flickr.com/photos/prusajr/5410919911/<br />
http://www.flickr.com/photos/prusajr/5410919707/<br />
<br />
When mounted only using the four corners, the inherent warp of the pcb can be a problem, hence it is better to use the cork mounting system above (as the piece of cork in the centre helps to keep the pcb flat).<br />
Magnets can be used in replace of the cork, this makes the bed removable. However, I (mooneyj) have only tried this on a darwin type printer (where the build platform only moves in z). During fast printing, the darwin vibrates and it seems the heatbed magnets slide over each other slightly. The acceleration of the y axis on a mendel may cause the magnets to slide also. Perhaps a hybrid of magnet and bolt mounting would work well?.<br />
<br />
'''The current standard (as of January 2015)''', however, is to simply place a square (200mm x 200mm) piece of glass on top of the heatbed, and affix it on the four sides with bulldog clips. The clips will not melt under pressure, and sufficiently hold the glass to the bed. This makes removal easier for cleaning as well.<br />
<br />
[[File:Heatbed_glass_clips_1a.jpg|600px|PCB heatbed mounted on P3Steel (Prusa i3 variant) with glass and bulldog clips.]]<br />
<br />
==Sides==<br />
<br />
The PCB heatbed has two sides, one with the copper traces (bottom side) and one without (top). On older versions of the PCB heatbed only the side without traces carried a silkscreen. Currently (as of January 2015) PCB heatbeds are silkscreened on both sides.<br />
<br />
Previously, printing on the top side was considered to be safer as the copper traces could be damaged if the print head would collide with the heatbed surface (if for example the Z-min endstop malfunctioned). Obviously if a piece of glass is used as the print surface, it protects the PCB copper traces. However, make sure your heatbed mounting springs are not too strong to prevent damage to the glass in case of an accidental collision.<br />
<br />
Note that the LED, resistor and wire connections are also liable to accidentally collide with the print head.<br />
<br />
Again, '''the current standard (as of January 2015)''' when the PCB heatbed is used with a piece of glass as the build surface '''is to mount the PCB heatbed with the traces up'''. This improves heat transfer to the glass and the PCB heats up faster.<br />
<br />
[[File:PCB_HEATBED.jpg]]<br />
<br />
==Connection==<br />
<br />
<br />
===Optional LEDs===<br />
<br />
The LEDs are optional, but if you choose to use the LEDs you MUST install the resistor.<br />
<br />
''''Parts''''<br />
<br />
2 x Surface Mount LEDs<br />
<br />
1 x 1K ohm Surface Mount Resistor<br />
<br />
<br />
<br />
Mount the LEDs in different directions (polarity) so that one of the LEDs will light up regardless of the board's polarity. You can use a single LED if you are certain of the polarity.<br />
<br />
[[File:PCB_HEATBED_DIAGRAM_r.jpg]]<br />
<br />
===Electronics===<br />
''RAMPS''<br />
<br />
See [[RAMPS1.4]], [[RAMPS1.3]], or [[RAMPS1.2]] depending on your version.<br />
<br />
''Sanguinolou''<br />
The MK2 PCB heatbed heats up to 110C when powered through the heated bed connection on Sanguinolou. Your power supply should be 300W and you should ensure that the wires from your power supply to the Sanguinolou are capable of handling the total draw of 20A+. Using a 300W ATX power supply with the 4wire ATX dual 12V connector is working well for me.<br />
<br />
N.B. It is recommended that you use a heatsink on your heated bed mosfet, it will get hot!<br />
<br />
N.B. It is recommended that you measure the resistance of your board. I (evilB) didn't and blew up my Ramps 1.2 MOSFET because of a too high current. My measured resistance was 0.8 Ohm.<br />
<br />
==Troubleshooting==<br />
<br />
The heatbed is often the source of various problems in RepRap 3D printers. The following is a list of possible problems and how to correctly diagnose their cause and possible solutions:<br />
<br />
<br />
'''T1) As soon as the PCB heatbed is turned on, my power supply switches off.'''<br />
<br />
: '''D1)''' Check that your power supply can effectively supply 12V @ 15A or more. If you are using an old PC power supply, it may not be able to provide the required current, or it could need a balancing resistor.<br />
<br />
:: '''S1)''' Use a better power supply. See [[Choosing a Power Supply for your RepRap]].<br />
<br />
<br />
'''T2) My PCB heatbed never reaches the required temperature, or takes too long to reach the required temperature'''.<br />
<br />
This is probably the most common problem with heatbeds that RepRap builders have to deal with. It can have various causes:<br />
<br />
: '''D2a)''' Turn off your printer completely, and measure the resistance of your heatbed using a multimeter: it should not be higher than 1.2 Ohm. If it is higher than 1.2 Ohm, your heatbed will not get enough current and will not dissipate enough heat to reach the required temperatures.<br />
<br />
:: '''S2a)''' Return the heatbed to whomever sold it to you and make sure to get one with a proper resistance!<br />
<br />
: '''D2b)''' If you have measured the resistance of your PCB heatbed and it is lower than 1.2 Ohm, you need to check the voltage across the heatbed terminals when it is heating up. If the voltage is significantly below, say, 11.7V, then again your heatbed will not get enough current and will not dissipate enough heat to reach the required temperatures.<br />
<br />
:: '''S2b)''' Make sure you are using electrical cable with a proper gauge (14 gauge recommended) to connect the heatbed to the controller board. And again, make sure your power supply provides the proper voltage under load conditions. Change components as required.<br />
<br />
: '''D2c)''' Make sure you have the PCB traces on the upper side of your heatbed!<br />
<br />
:: '''S2c)''' Flip the PCB heatbed if required.<br />
<br />
<br />
'''T3) I have checked the temperature on the PCB heatbed and it does not provide uniform heating.'''.<br />
<br />
: '''D3)''' This is actually quite common and not a very serious problem as long as the variation in temperature is below +/- 3C between center and periphery. The corners will always be a little cooler, too.<br />
<br />
:: '''S3)''' Check the various PCB insulation methods listed below. They will minimize heat losses from the underside of the PCB.<br />
<br />
<br />
The following video shows a PCB heatbed MK2 being heated to 60 degrees as seen by an infrared camera:<br />
<videoflash>QE90bDUaAno</videoflash><br />
<br />
==Thermal insulation==<br />
<br />
It's a good idea to insulate the underside of the heatbed in order to get a faster heat up time and a overall better thermal performance. For higher temperatures, an insulation might even be required.<br />
<br />
[[File:Thermal_Isolation.png | thumb | 300px | right | Cork plate cut to fit under a PCB heated bed.]] <br />
<br />
Solutions found to work are:<br />
<br />
* Cork plate.<br />
* Cotton batting.<br />
* Wool felt sheet.<br />
* Rescue sheet, see e.g. [[Robert's Heated Bed]] ie the silver or gold rescue blanket used by hikers.<br />
* Glass fibre soldering/plumbers/welding mat<br />
* Silicon or teflon cooking sheet<br />
<br />
{{Clear}}<br />
<br />
== FORKS (not done by Prusa)==<br />
<br />
=== MK2, MK2a ===<br />
<br />
It's not successor of MK1 even with it's name. It's concurrent design. - Josef Prusa<br />
<br />
MK2a Heatbed with minor changes by Tony from [http://www.think3dprint3d.com/ Think3dPrint3d]<br />
<br />
==== About the MK2a ====<br />
<br />
I liked Josef's original design but wanted to be able to use through hole components, have the thermistor poke through the middle and for it to look good on the 'back' with the silkscreen that Josef designed on that side as well.<br />
<br />
The MK2a has a few further changes:<br />
<br />
* A mounting hole in the middle of one edge to allow for easier bed levelling, thanks to [http://hydraraptor.blogspot.com/2012/05/bed-levelling.html Nophead] for this suggestion.<br />
* Larger LED and Resistor pads to allow for 1206 size surface mount components.<br />
* Much larger area to solder the current carrying wire, easily connect ribbon cable (such as with the Mendel90 heatbed connection). Also the through holes increased in size.<br />
* The redundant pads on the non-heating element side of the board removed to prevent confusion. These are not electrically connected if the board is not plated (plated boards are bad for the reasons outlined by Josef Prusa above).<br />
<br />
==== Further update of the MK2a ====<br />
(by Tony from [http://www.think3dprint3d.com/ Think3dPrint3d])<br />
<br />
In order to make ribbon cable easier to use we have made the following changes:<br />
<br />
Holes in the extended solder pads<br />
<br />
[[File:MK2a-header_holes.jpg | 600px]]<br />
<br />
This allows for IDC compatible pin headers to be used <br />
<br />
[[File:MK2a-headers.jpg | 600px]]<br />
<br />
This in turn makes plugging in a heated bed wiring loom very easy<br />
<br />
[[File:MK2a-headers_connectors.jpg | 600px]]<br />
<br />
==== Where to get it ====<br />
<br />
The MK2 .brd file is available here: [[File:PCB_heatedbed_Mk2.brd]][[http://www.reprap.cn/free-shipping-the-reprap-3d-printer-heating-bed-pcb-heatbed-mk2b-p-53.html?cPath=19]]<br />
<br />
The MK2a .brd file is available here [[File:PCB_heatedbed_Mk2a.brd]]<br />
<br />
Manufactured MK2 PCBs can be found here:<br />
<br />
[http://www.robotdigg.com/product/99 MK2B From RobotDigg (CN) ]<br />
<br />
[http://www.easyreprap.com/#!product/prd1/2114060485/easy-reprap-dual-power-mk2b-heat-bed MK2B From Easy RepRap (USA) ]<br />
<br />
[https://taotac.com/sanpham/pcb-heatbed/ MK2A, MK2B, MK3 - TaoTac.com VN]<br />
<br />
[http://twelvepro.com/index.php?route=product/product&path=67&product_id=77 MK2B Dual power 12/24V US]<br />
<br />
[https://alfa-tech3d.com/da/ Alfa-Tech3D MK2B (DK, Worldwide)]<br />
<br />
[http://www.think3dprint3d.com/Electronics/PCB-Heatbed-MK2a Think3dPrint3d (UK, Worldwide)]<br />
<br />
[http://www.3distributed.com/products/mk2-heated-bed-1 http://www.3distributed.com/products/mk2-heated-bed-1]<br />
<br />
[http://www.charlies3dtechnologies.com/webshop Charlie's 3D Technologies]<br />
<br />
[http://gadgets3d.com/index.php?route=product/product&product_id=59 www.gadgets3d.com]<br />
<br />
[http://reprap.me/electronics/reprap-pcb-heatbed-mk2.html www.RepRap.me]<br />
<br />
[https://www.rp3d.com/shop/electronics-c-8_14.html rp3d.com]<br />
<br />
[http://stores.ebay.ca/botechengineeringpcbservice Botech Circuits MK2a]<br />
<br />
[http://www.ebay.co.uk/sch/i.html?_nkw=heatbed+reprap+MK2a&_sacat=See-All-Categories#ptm eBay MK2a]<br />
<br />
[http://www.emakershop.com/browse/listing?l=126 eMakerShop MK2a]<br />
<br />
[http://store.thingibox.com/en/temperature/30-heated_bed_rectangluar.html MK2a, MK2b (214x214mm, 314x214mm and 326x326mm) from ThingiBOX]<br />
<br />
[http://stores.ebay.com/reprapdiscount Reprapdiscount MK2 and MK2a eBay]<br />
<br />
[http://www.paoparts.com/fr/200-plaque-chauffante-mk2a.html Paoparts (fr) MK2a]<br />
<br />
[http://www.cubic-print.com/PCB-heated-bed-MK2 Cubic Print (Germany)]<br />
<br />
[http://www.uw3dprinter.nl/en/heatbed-mk2.html Uw3Dprinter.nl MK2 (NL,BE,DE,FR)]<br />
<br />
[http://www.createc3d.com CREATEC 3D (ES, Worldwide)]<br />
<br />
[http://impresoras3dlowcost.com/62-cama-caliente-heatbed-mk2b.html i3Dlc MK2B (SPAIN)]<br />
<br />
[http://nioz.ru/index.php/komplektuyushchie/dlya-3d-printera/mk2b-detail MK2B (RU)]<br />
<br />
[http://reprapworld.com/?products_details&products_id/358/cPath/1645 RepRapWorld]<br />
<br />
[http://www.reprap.pt/pecas/sistema-quente/mesa-aquecida-mk2b RepRap Portugal] MK2B Red and Black<br />
<br />
[http://opensourcehardware.it/en/cerca?controller=search&orderby=position&orderway=desc&search_query=heatbed+&submit_search= opensourcehardware.it (MK2B, MK3-ALU, MK3 300x200)]<br />
<br />
[http://www.hta3d.com/Cama-Caliente www.hta3d.com (MK2A 300x200, MK2B, MK3-ALU, Borosilicate tempered glass and more!!)]<br />
<br />
[http://orballoprinting.com/en/electronics/21-hotbed-mk2b.html orballoprinting.com MK3 MK2B wolrdwide shipping]<br />
<br />
==== Printing ====<br />
'''MK2'''<br />
<br />
Although you can print directly to the bed covered in polyimide tape, no PCB is perfectly flat. It is recommended that you follow the directions in mounting, below, for better results.<br />
<br />
==== Mounting ====<br />
'''MK2'''<br />
<br />
The MK2 board can be mounted either side up and is designed to be mounted as Josef describes:<br />
<br />
http://josefprusa.cz/pcb-heatbed-final-mounting-and-wiring-solutio<br />
<br />
The holes in the 4 corners to attach the heated bed MK2 to the top print plate are not suitable for M3 bolts though! Use M2.5 instead.<br />
<br />
The glass protects the tracks from a head crash and is easily swapped out.<br />
<br />
The board dimensions are identical to the MK1 design.<br />
<br />
Insulation between the board and the thick plate should improve heat-up times and reduce energy consumption. An example is here:<br />
<br />
http://reprap.org/wiki/Mendel_heated_bed#Thermal_Insulation<br />
<br />
''Caution, I have not tried this with the temperatures that the PCB bed can reach!''<br />
<br />
'''MK2a'''<br />
<br />
The MK2a has a central mounting hole on the front side to allow for three point mounting. This is much easier for bed leveling in comparison to 4 point mounting. First level the side with two holes and fix in place, then level the side with one hole. A glass plate is highly recommended to provide a truly flat surface and rigidity.<br />
<br />
[[File:Mk2a_Central_Mount_Point.jpg |200 px]]<br />
<br />
====Sides====<br />
'''MK2'''<br />
<br />
The PCB still has a side with the traces on and a side without but now the silkscreen is on both the top and bottom, this makes it look good even when 'upside down' under a layer of glass. The LED, resistor and power wires can be mounted on either side of the board, with either surface mount or through hole components. If you are using through hole be careful when soldering not to interfere with the glass and introduce a gap between the glass and the PCB. If the MK2 board is made properly without copper plating then be sure to only solder the LED and resistor to the same side and the tracks. This problem is solved in the MK2a by removing the pads on the non connected side.<br />
<br />
MK2<br />
[[File:PCB_Heatbed_MK2_front_small.jpg| 400px]]<br />
<br />
<br />
MK2a<br />
[[File:Mk2a.jpg| 400px]]<br />
<br />
<br />
MK2b Dual Power<br />
[[File:RRD-Mk2b-dual-power.jpg| 400px]][[File:RRD-Mk2b-dual-power_blk.jpg| 445px]]<br />
<br />
There is a central hole in the board and it is sized so a small thermistor<br />
(for example the EPCOS one: http://uk.farnell.com/jsp/search/productdetail.jsp?CMP=i-ddd7-00001003&sku=3878697 ) will fit though it allowing contact directly with the glass.<br />
''todo: test efficacy of using heat sink compound to better thermally couple the thermistor to the glass''<br />
<br />
[[File:PCB_Heatbed_MK2_therm_hole.jpg| 200px]]<br />
<br />
====Connection====<br />
Polarity doesn't affect the PCB, however the LEDs have a polarity.<br />
<br />
'''MK2'''<br />
<br />
There are pads and un-plated through holes for connecting the power wires. Ensure that the wire you use is thick enough for 10A, and solder it to the pads on the track side of the PCB. It is a good idea to think about strain relief so your moving build platform does not flex the joint, this can lead to failure of the joint over time. I recommend routing the wire from the heated bed to strain relief on the thick sheet before routing it to your controller/power supply. ''todo: get pictures of strain relief''<br />
<br />
'''MK2a'''<br />
<br />
The pads to solder onto have been greatly increased as shown in the picture below. The picture shows the wires prepared for soldering routed through the holes for extra security. This does not remove the need to use proper strain relief.<br />
<br />
[[File:Mk2a_Through_Hole.jpg|400 px]]<br />
<br />
'''MK2b Dual Power'''<br />
<br />
As you can see in the pictures below depending on the voltage you want to use you have to use different solder pads, but it's written on the PCB which pads have to be used for which voltage.<br />
<br />
[[File:RRD-Mk2b-dual-power-table.jpg|400px]] [[File:RRD-Mk2b-dual-power-connector_red_blk.jpg|400px]]<br />
<br />
'''MK2i'''<br />
The MK2i is connected just like the MK2a heatbed.<br />
<br />
=====Optional LEDs=====<br />
'''MK2'''<br />
<br />
The LEDs are optional, but if you choose to use the LEDs you MUST install the resistor. Solder the components to the pads on the track side of the PCB. With the MK2, conventional wired parts can be substituted for the surface mount parts. If your MK2 board is made properly without copper plating then be sure to only solder the LED and resistor to the same side and the tracks. This problem is solved in the MK2a by removing the pads on the non connected side.<br />
<br />
<br />
''''Parts''''<br />
<br />
2 x surface mount (0805 size on the MK1 and MK2, 1206 size on the MK2a for easier soldering) or conventional through-hole LEDs. Install with opposite polarity so one or the other will light up regardless of the polarity of the power supply to the board.<br />
<br />
1 x 1K ohm surface mount or through-hole resistor<br />
<br />
=== MK2b Dual Power Technical Details===<br />
You can find the open source files here: http://forum.reprapdiscount.com/forums/oss/<br />
<br />
* Dimensions 214mmx 214mm<br />
* Laminate FR4 1.6+-0.15mm<br />
* 2 layer, 35μm copper<br />
* Red Soldermask - both sides<br />
* White Silkscreen - both sides<br />
* Power Input: 12V or 24v<br />
* copper plated holes<br />
* resistance between 1.0-1.2 ohm (12V) or 3-3.4 ohm (24V) (Sainsmart board came in at 1.8 ohm @ 12V/3.6 ohm @ 24V)<br />
<br />
=== MK2i ===<br />
[[File:IMG_8284_smnocopy.png|400px]]<br />
[[File:IMG_8271_smnocopy.png|400px]]<br />
<br />
The MK2i is a hybrid of MK2a and MK3 designs. It supports 4-point and 3-point mounting. There is a central hole in the PCB for a through hole thermistor such as EPCOS. There are also pads on top and bottom for an SMD or through-hole thermistor. The pads are on the top/bottom (in the center of the PCB, next to the hole) but the thermistor trace is on the top copper and routes again to the bottom for easier wiring, labelled "NTC". This design is versatile and much less tape is needed for strain relief on the thermistor wires.<br />
<br />
The MK2i also sports an internationalized stencil on top and bottom. The stencil has new international symbols for "hot" and "hot - do not touch", as well as translations in English, Spanish, French, and German. The original CAD file also had translations in Chinese, Russian, Arabic, and Japanese - but it fails to export these character sets so they aren't in the final version.<br />
<br />
The code is at [https://github.com/Terawatt-Industries/mk2i https://github.com/Terawatt-Industries/mk2i] and comes with a LBR library file. You should be able to have PCBs made from the MK2i Gerbers. It's probably feasible to make this by hand - as much as an MK2a PCB - except in this case you must have bottom and top layers if you want the thermistor wiring feature.<br />
<br />
== MK2 A4 ==<br />
<br />
This is [[Clone_Wars:_Othon | my build]]. I always wanted a big bed, in order to be able to plot (yes, actually plot, with artistic purpouses) at least DIN A4 in size. So I built my prusa mendel big enough to be able to host such a HBP PCB. I'm no good with any PCB editor, so I made my files in a CAD program, and exported the result file into a dxf file. The file has several layers the names of which should make the information self understandable. Anyway I'll tell: the layers with number names represent the routing of the traces the width of which is the layer's name in mm. The design was basically copied from MK2a. The engineering was made with an evolutive algorithm developed by [[Clone_Wars:_Othon | Damrod]] in [http://www.grasshopper3d.com/ grasshopper]. The manufacturing was a bit faulty, but it works flawlessly.<br />
<br />
* Dimensions 215mmx 315mm<br />
* 1 layer 35μm copper<br />
* resistance between 1.0 and 1.2 ohm<br />
<br />
[[File:Big_Heatbed.JPG|600 px]]<br />
<br />
[https://dl.dropboxusercontent.com/u/6334877/PCB%20HBP%20A4/gerber.zip source gerber]<br />
[https://dl.dropboxusercontent.com/u/6334877/PCB%20HBP%20A4/Mi%20HBP2.dxf source dxf]<br />
<br />
== PCB Heatbed 200X300mm ==<br />
<br />
<br />
<br />
[[file:200X300.jpg|600 px]]<br />
[[file:200X300-TOP.jpg|600 px]]<br />
<br />
The PCB Heatbed 200X300mm has a 100mm bigger built area then the regular MK2 heatbed and the overall outline is 214X314mm.<br />
<br />
It has dual power mode optimized for 12 or 24V but you can also use everything in between (16V, 19V what have you)<br />
(Your printer controller will regulate the power to the heatbed in order to get your preset temperature.)<br />
<br />
The core is regular 1.6mm FR4 PCB and the print surface is the same as regular heatbeds but with a metric ruler grid. <br />
<br />
The connections to the heatbed is the same as the connections on the MK3 Alu. heatbed belov.<br />
<br />
The PCB Heatbed 200X300mm is now available in the [http://reprap.me/ RepRap.me] webshop. <br />
<br />
* Dimensions 214mm x 314mm<br />
* 1 layer 35μm (1oz base) copper<br />
* Resistance between 1 and 1.3 ohm for the 12V<br />
* Resistance between 4.5 and 5 ohm for the 24V<br />
* 110 degrees Celsius possible for both 12V and 24V<br />
* Running 24V on the 12V terminals will heatup the heatbed to 100 degree in only 2 minutes<br />
* 180 degree Celsius max. temperature<br />
<br />
== MK3 ALU-Heatbed Dual Power ==<br />
<br />
The [http://reprap.me/Alu-Heatbed-MK3 Alu-Heatbed MK3] have features similar to MK2 and you can also operate this board with 12V or 24V.<br><br />
<br />
- Heatbed with 3.2mm Aluminum Core. Print directly on the heatbed, no need for glass plate. It's a much lighter solution than PCB heatbed + glass, which makes it better for faster prints.<br><br />
- Dual power supply. Operate at 12V or 24V. You can use thinner wires when operating at 24V.<br><br />
- A central mounting hole on the front side to allow for three point mounting. This is much easier for bed leveling in comparison to 4 point mounting. First level the side with two holes and fix in place, then level the side with one hole.<br><br />
- Large solder pads for multiple wires (ribbon cable) or a SMD pinhead connector can be mounted.<br><br />
- Pads for SMD thermistor 1206<br><br />
<br />
* Dimensions 214mm x 214mm<br />
* 1 layer 35μm (1oz base) copper<br />
* Resistance between 1.4 and 1.6 ohm for the 12V<br />
* Resistance between 5.0 and 5.4 ohm for the 24V<br />
* 100 degree Celsius possible for both 12V and 24V<br />
* With 15V on the 12V terminals will maintain approx. 115 degree Celsius without regulation<br />
* Running 24V on the 12V terminals will heatup the heatbed to 100 degree in only 2 minutes (Your printer controller will regulate the power to the heatbed in order to get your preset temperature.)<br />
* 180 degree Celsius max. temperature<br />
<br />
[[File:alu_heatbed.JPG|600 px]]<br />
''' Bottom side (Do not print directly on this side)'''<br />
<br />
[[file:Alu TOP .jpg|600 px]]<br />
''' Top side (Printing side) '''<br />
<br />
[[File:Alu 12V small.jpg|300 px]]<br />
[[File:Alu 24V small.jpg|300 px]]<br />
<br />
When connecting the heatbed in the 12V setting it is important that you connect solder pad 2 and 3 directly on the heatbed. <br />
<br />
Recommended NTC: EPCOS - B57621C104J62 - THERMISTOR, 100K "or whatever [[thermistor]] you normally use."<br />
<br />
==== Where to get it ====<br />
<br />
[https://alfa-tech3d.com/en/building-platform-bed/heat-bed-mk2b-dual-power-prusa-resistor-and-leds-soldered.html Alfa-Tech3D] <br /><br />
[http://reprap.me/electronics/alu-reprap-heater-board-mk3.html www.RepRap.me]<br /><br />
[http://www.cubic-print.com/MK3-aluminum www.cubic-print.de]<br /> (Cubic-Print currently only offers the version of the bed thats needs a wired thermistor. The SMD pads are solely for SMD LEDs and their resistor.)<br /><br />
[https://taotac.com/sanpham/pcb-heatbed/ TaoTac.com]<br />
<br />
[http://store.thingibox.com/en/temperature/30-heated_bed_rectangluar.html MK3 from ThingiBOX]<br />
<br />
[http://www.robotdigg.com/product/202/MK3-Dual-Power-ALU-Heatbed RobotDigg]<br />
<br />
[http://aus3d.com.au/printer-parts/printer-bed Aus3D]<br />
<br />
[http://www.reprap.cn/free-shipping-the-reprap-3d-printer-heating-bed-pcb-heatbed-mk2b-p-53.html Free shipping $13]<br />
<br />
[http://www.geeetech.com/mk2b-heated-bed-prusa-soldered-resistorleds-for-reprap-mendel-p-802.html MK2A]<br />
<br />
[http://www.reprap.cn/free-shipping-prusa-i3-heat-bed-mk3-p-96.html?cPath=19 MK3]<br />
<br />
[https://reprap.pt/pecas/mesas-heated-bed RepRap.pt Heated Beds]<br />
<br />
== MK2a layout in SVG-format ==<br />
<br />
There's an SVG-version (Inkscape) of the MK2a-layout.<br />
<br />
For the toner transfer method and people that only have a printer for letter/DIN A4 there's a version with two separated parts.<br />
Because the parts only have few electrical contacts between them, they easily can be ironed next to each other, fixing the needed bridges with etch resistant paint before etching.<br />
<br />
<gallery><br />
File:Layout_Heatbed_MK2a.svg|MK2A in SVG<br />
File:Layout_Heatbed_RK1_parts_a_b.svg|Printer friendly Part I<br />
File:Layout_Heatbed_RK1_parts_c_d.svg|Printer friendly Part II<br />
File:All_breaches_fixed.JPG|Toner transfered and ready to etch<br />
File:Etched and ready.JPG|The etched board<br />
</gallery><br />
<br />
(You may follow the complete process here: [[Etched_heatbed_construction]])</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Prusa_i3_ION&diff=181288Prusa i3 ION2018-01-16T15:17:36Z<p>Merlucin: /* Where to buy */</p>
<hr />
<div>{{Languages}}<br />
<br />
{{Development<br />
<!--Header--><br />
|name = ION V6<br />
|status = working<br />
<!--Image--><br />
|image = Prusa i3 ION.PNG<br />
<!--General--><br />
|description = 3D printer inspired in the Prusa i3<br />
|reprap = Prusa i3<br />
|license = [[GPL]]<br />
|author = ThingiBOX<br />
|categories =<br />
[[:Category:Prusa i3|Prusa i3]],<br />
{{tag|Prusa i3 Development}},<br />
{{tag|Prusa Mendel Development}},<br />
{{tag|Prusa Mendel}},<br />
{{tag|Mendel Variations}},<br />
{{tag|Cartesian-XZ-head}}<br />
}}<br />
<br />
<br />
=Introduction=<br />
<br />
[[Image:Prusai3 ION Front.jpg|thumb|300px|left|Front image Prusa i3 ION]]<br />
<br />
::The '''ION V6''' is a 3D printer inspired in the Prusa i3, but with many changes, improvements and updates. It has been designed by the technical team of [http://store.thingibox.com ThingiBOX], an online store whose products are related to the world of 3D printing.<br />
<br />
::The project goal was to design a structure made with methacrylate where all the parts where cut by a CNC Laser Machine, the other goal was to keep all the electronics inside the printer making it look clean and tidy. To facilitate cooling of electronics there are fans working towards the shields.<br />
<br />
::The maximum print volume is 200x200x150mm on a heated bed MK3 aluminum and above it a borosilicate glass (prepared for the abrupt change between temperatures), so it can be printed with ABS without any problems (if lacquer is applied).<br />
<br />
::The extruder is a v5 E3D all metal that can heat up to 300 ºC. All kinds of plastic material (ABS, PLA, etc ...) available on the market can be used in this printer. There is the option of choosing the filament diameter that the extruder supports, so we offer it in 3mm or 1.75mm. The nozzle has an orifice of 0.4mm in both cases.<br />
<br />
::There is also a fan (and its support) for the radiator of the extruder whose function is to prevent the filament clogging the duct.<br />
<br />
::To drive the filament there is a gearwheel that magnifies the force that the stepper can do and drives a MK8 hobbed bolt.<br />
<br />
::For the Z axis (the height) is recommended to choose the option that contains the bars Tr8x8 because that improves the print quality significantly.<br />
<br />
::For the movement of the other two axes GT2 pulleys and synchronous belts are used.<br />
<br />
::For the electronics; An Arduino MEGA 2560 in conjunction with a 1.4 RAMPS is used, also including 4 A4988 drivers that drive 5 NEMA17 stepper motors. 3 end stop switches are also included in order to home the axes automatically.<br />
<br><br><br />
::To give the necessary power is also provided a power supply that outputs 12V and 30A (360W).<br />
<br />
::Cables that are outside the base of the printer are confined in a cable chain in order to protect them during axis movement and making it look all tidy.<br />
<br />
::At the rear of the base there are two connectors, one to connect with the AC power switch and one USB jack is embedded. It also has a space if you want to connect a Raspberry Pi (not included) to control the machine with Ocotprint through internet.<br />
<br />
::In the options it is also given the possibility of adding a 2004 LCD screen as it is not necessary to print when connected by USB to a PC, but if you want to use it without a computer is recommended to choose the LCD as it incorporates a SD card reader.<br />
<br />
=Technical Data=<br />
{| class="wikitable sortable" border="1" align="center"<br />
|-<br />
| Frame || White methacrylate 10mm Transparent methacrylate 5mm<br />
|-<br />
| Smooth rods|| 304 Steel, tolerance H9 <br />
|-<br />
| Threaded rods || Thread Tr8x8 or M8 (optional)<br />
|-<br />
| Print volume || 200x200x150 mm<br />
|-<br />
| Extruder || E3D v5 (All metal)<br />
|-<br />
| Filament diameter || 1.75/3 mm (optional) <br />
|-<br />
| Filament types || All types (PLA, ABS, Nylon, etc...)<br />
|-<br />
| Electronics || Arduino MEGA 2560 - RAMPS 1.4<br />
|-<br />
| Drivers || 4 x A4988<br />
|-<br />
| Power source || 12V/30A<br />
|-<br />
| Build platform || Aluminum MK3 Heated Bed (12-24V)<br />
|-<br />
| Display|| LCD 2004 with SD card reader (optional)<br />
|}<br />
<br />
==Documentation==<br />
* [http://es.docs.thingibox.com/ Assembly instructions and commissioning guide]<br />
* [https://github.com/Thingibox/ThingiBOX_Marlin Configured firmware]<br />
* [https://github.com/Thingibox/Prusa-i3-ION/tree/master/Slic3r_Configuration Configured Slic3r profile]<br />
<br />
==Features==<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION axial fans.jpg|150px|thumb|Axial fans]] ||<br />
::Unlike the original Prusa i3, our version has an opening for the electronics and the printer’s power supply. Thanks to the housing the electronic components such as control boards, power supply, cables and connectors are stowed in an orderly and safe manner.<br />
<br />
::Two small axial fans ensure the cooling of the electronics. The power supply features a built-in temperature control that cuts off electrical power in case of overheating.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION heated bed.jpg|150px|thumb|Heated bed]] ||<br />
::The maximum printing volume ist 200x200x190mm. The objets are printed on a 3mm thick borosilicate glass which features low thermal expansion. Beneath the glass we place a MK3 heated bed attached to a 3mm aluminium board that provides extra rigidity and at the same time allows to print filaments that present adhesion problems when printing at low temperature, such as ABS.<br />
<br />
::Depending on humidity conditions and room temperature, the heated bed can reach a temperature of 90ºC.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION extruder.jpg|150px|thumb|Extruder]] ||<br />
::The extruder is an E3D v5 full metal hotend that allows to print at temperatures as high as 300ºC. It is compatible with almost all available filaments. The nozzle has a 0.4mm diameter, this is a compromise between printing precision and speed.<br />
<br />
::An additional fan prevents the filament from melting before time and thus clogging the duct. The extruder incorporates standard components and can be completely disassembled; this makes cleaning and spare part replacements easier.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION MK8 drive gear wheel.jpeg|150px|thumb|MK8 drive gear wheel]] ||<br />
::The Prusa i3 ION uses a MK8 drive gear wheel to feed the filament into the extruder. The wheel is fixed on an axis with a gear on one end which increases by factor five the power that is transmitted by the motor. This way we can use a smaller motor in the extruder, reducing the motor’s inertia and increasing printing quality at the same time. This applies specially where the extruder suddenly changes its speed, for instance when printing corners.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION Z axis.jpeg|150px|thumb|Z axis]] ||<br />
::For the Z axis (which is responsible for lifting the printer head) we recommend the option containing the Tr8x8 threaded bars because they improve considerably the printing results. The traditional metric, non-calibrated bars are significantly less expensive, but they may cause ripples in the printed object which are more visible the taller the object is.<br />
<br />
::With the Tr8x8 bars we employ machined POM nuts that completely eliminate the backslash, typical in traditional threaded bar configurations. For an even higher precision, our POM nuts are 10mm longer than the usual nuts.<br />
<br />
::For the movement of the other axis the printer uses GT2 synchronous and belts with manual tensors.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION electronics.jpg|150px|thumb|Arduino MEGA 2560]] ||<br />
::As for the electronics, this printer includes an Arduino MEGA 2560 controller together with a RAMPS 1.4 shield that incorporates 4 A4988 drivers which move 5 NEMA17 stepper motors. Also included are 3 endstop switches with cable for automatic homing.<br />
<br />
::Although the printer consumes about 200W when the heated bed is running, the included power source can provide up to 360W (30 amp DC at 12V) and features a security system that cuts power off in case of a short circuit.<br />
<br />
::The external wires of the printer are hold in a cable chain. This way the cables are kept orderly and safe while the axis are moving.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION socket.jpeg|150px|thumb|Socket with switch]] ||<br />
::Two connectors are situated on the back side, one for the AC power supply through a socket with switch and one for USB connections in case you wish to control the printer directly from your PC.<br />
<br />
::The housing features also an opening and bores for a Raspberry Pi 2 (not included) which allows to connect the printer to the internet and control it via Octoprint.<br />
|-<br />
|}<br />
<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION LCD.jpeg|150px|thumb|LCD 2004 screen]] ||<br />
::Optionally, you can purchase a LCD 2004 screen for monitoring the printer. The screen controller includes a SD card that allows to load designs without the need for a PC.<br />
<br />
::There is no need to modify the firmware for the display’s setup. With this board you can control the printing speed without having to wait for the hotend to cool down, preheat the printer, modify the firmware’s parameters, or change filament in the middle of the printing process; all this without a PC.<br />
|-<br />
|}<br />
<br />
=Where to buy=<br />
<br />
- [http://store.thingibox.com/es/ion-v6/373-ION_v6_kit_completo.html Complete Kit in ThingiBOX] Now Available!<br />
- [http://store.thingibox.com/es/ion-v6/374-ION_v6_XL_kit_completo.html Complete Kit XL in ThingiBOX] Now Available!</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Prusa_i3_ION&diff=181287Prusa i3 ION2018-01-16T15:13:06Z<p>Merlucin: </p>
<hr />
<div>{{Languages}}<br />
<br />
{{Development<br />
<!--Header--><br />
|name = ION V6<br />
|status = working<br />
<!--Image--><br />
|image = Prusa i3 ION.PNG<br />
<!--General--><br />
|description = 3D printer inspired in the Prusa i3<br />
|reprap = Prusa i3<br />
|license = [[GPL]]<br />
|author = ThingiBOX<br />
|categories =<br />
[[:Category:Prusa i3|Prusa i3]],<br />
{{tag|Prusa i3 Development}},<br />
{{tag|Prusa Mendel Development}},<br />
{{tag|Prusa Mendel}},<br />
{{tag|Mendel Variations}},<br />
{{tag|Cartesian-XZ-head}}<br />
}}<br />
<br />
<br />
=Introduction=<br />
<br />
[[Image:Prusai3 ION Front.jpg|thumb|300px|left|Front image Prusa i3 ION]]<br />
<br />
::The '''ION V6''' is a 3D printer inspired in the Prusa i3, but with many changes, improvements and updates. It has been designed by the technical team of [http://store.thingibox.com ThingiBOX], an online store whose products are related to the world of 3D printing.<br />
<br />
::The project goal was to design a structure made with methacrylate where all the parts where cut by a CNC Laser Machine, the other goal was to keep all the electronics inside the printer making it look clean and tidy. To facilitate cooling of electronics there are fans working towards the shields.<br />
<br />
::The maximum print volume is 200x200x150mm on a heated bed MK3 aluminum and above it a borosilicate glass (prepared for the abrupt change between temperatures), so it can be printed with ABS without any problems (if lacquer is applied).<br />
<br />
::The extruder is a v5 E3D all metal that can heat up to 300 ºC. All kinds of plastic material (ABS, PLA, etc ...) available on the market can be used in this printer. There is the option of choosing the filament diameter that the extruder supports, so we offer it in 3mm or 1.75mm. The nozzle has an orifice of 0.4mm in both cases.<br />
<br />
::There is also a fan (and its support) for the radiator of the extruder whose function is to prevent the filament clogging the duct.<br />
<br />
::To drive the filament there is a gearwheel that magnifies the force that the stepper can do and drives a MK8 hobbed bolt.<br />
<br />
::For the Z axis (the height) is recommended to choose the option that contains the bars Tr8x8 because that improves the print quality significantly.<br />
<br />
::For the movement of the other two axes GT2 pulleys and synchronous belts are used.<br />
<br />
::For the electronics; An Arduino MEGA 2560 in conjunction with a 1.4 RAMPS is used, also including 4 A4988 drivers that drive 5 NEMA17 stepper motors. 3 end stop switches are also included in order to home the axes automatically.<br />
<br><br><br />
::To give the necessary power is also provided a power supply that outputs 12V and 30A (360W).<br />
<br />
::Cables that are outside the base of the printer are confined in a cable chain in order to protect them during axis movement and making it look all tidy.<br />
<br />
::At the rear of the base there are two connectors, one to connect with the AC power switch and one USB jack is embedded. It also has a space if you want to connect a Raspberry Pi (not included) to control the machine with Ocotprint through internet.<br />
<br />
::In the options it is also given the possibility of adding a 2004 LCD screen as it is not necessary to print when connected by USB to a PC, but if you want to use it without a computer is recommended to choose the LCD as it incorporates a SD card reader.<br />
<br />
=Technical Data=<br />
{| class="wikitable sortable" border="1" align="center"<br />
|-<br />
| Frame || White methacrylate 10mm Transparent methacrylate 5mm<br />
|-<br />
| Smooth rods|| 304 Steel, tolerance H9 <br />
|-<br />
| Threaded rods || Thread Tr8x8 or M8 (optional)<br />
|-<br />
| Print volume || 200x200x150 mm<br />
|-<br />
| Extruder || E3D v5 (All metal)<br />
|-<br />
| Filament diameter || 1.75/3 mm (optional) <br />
|-<br />
| Filament types || All types (PLA, ABS, Nylon, etc...)<br />
|-<br />
| Electronics || Arduino MEGA 2560 - RAMPS 1.4<br />
|-<br />
| Drivers || 4 x A4988<br />
|-<br />
| Power source || 12V/30A<br />
|-<br />
| Build platform || Aluminum MK3 Heated Bed (12-24V)<br />
|-<br />
| Display|| LCD 2004 with SD card reader (optional)<br />
|}<br />
<br />
==Documentation==<br />
* [http://es.docs.thingibox.com/ Assembly instructions and commissioning guide]<br />
* [https://github.com/Thingibox/ThingiBOX_Marlin Configured firmware]<br />
* [https://github.com/Thingibox/Prusa-i3-ION/tree/master/Slic3r_Configuration Configured Slic3r profile]<br />
<br />
==Features==<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION axial fans.jpg|150px|thumb|Axial fans]] ||<br />
::Unlike the original Prusa i3, our version has an opening for the electronics and the printer’s power supply. Thanks to the housing the electronic components such as control boards, power supply, cables and connectors are stowed in an orderly and safe manner.<br />
<br />
::Two small axial fans ensure the cooling of the electronics. The power supply features a built-in temperature control that cuts off electrical power in case of overheating.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION heated bed.jpg|150px|thumb|Heated bed]] ||<br />
::The maximum printing volume ist 200x200x190mm. The objets are printed on a 3mm thick borosilicate glass which features low thermal expansion. Beneath the glass we place a MK3 heated bed attached to a 3mm aluminium board that provides extra rigidity and at the same time allows to print filaments that present adhesion problems when printing at low temperature, such as ABS.<br />
<br />
::Depending on humidity conditions and room temperature, the heated bed can reach a temperature of 90ºC.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION extruder.jpg|150px|thumb|Extruder]] ||<br />
::The extruder is an E3D v5 full metal hotend that allows to print at temperatures as high as 300ºC. It is compatible with almost all available filaments. The nozzle has a 0.4mm diameter, this is a compromise between printing precision and speed.<br />
<br />
::An additional fan prevents the filament from melting before time and thus clogging the duct. The extruder incorporates standard components and can be completely disassembled; this makes cleaning and spare part replacements easier.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION MK8 drive gear wheel.jpeg|150px|thumb|MK8 drive gear wheel]] ||<br />
::The Prusa i3 ION uses a MK8 drive gear wheel to feed the filament into the extruder. The wheel is fixed on an axis with a gear on one end which increases by factor five the power that is transmitted by the motor. This way we can use a smaller motor in the extruder, reducing the motor’s inertia and increasing printing quality at the same time. This applies specially where the extruder suddenly changes its speed, for instance when printing corners.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION Z axis.jpeg|150px|thumb|Z axis]] ||<br />
::For the Z axis (which is responsible for lifting the printer head) we recommend the option containing the Tr8x8 threaded bars because they improve considerably the printing results. The traditional metric, non-calibrated bars are significantly less expensive, but they may cause ripples in the printed object which are more visible the taller the object is.<br />
<br />
::With the Tr8x8 bars we employ machined POM nuts that completely eliminate the backslash, typical in traditional threaded bar configurations. For an even higher precision, our POM nuts are 10mm longer than the usual nuts.<br />
<br />
::For the movement of the other axis the printer uses GT2 synchronous and belts with manual tensors.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION electronics.jpg|150px|thumb|Arduino MEGA 2560]] ||<br />
::As for the electronics, this printer includes an Arduino MEGA 2560 controller together with a RAMPS 1.4 shield that incorporates 4 A4988 drivers which move 5 NEMA17 stepper motors. Also included are 3 endstop switches with cable for automatic homing.<br />
<br />
::Although the printer consumes about 200W when the heated bed is running, the included power source can provide up to 360W (30 amp DC at 12V) and features a security system that cuts power off in case of a short circuit.<br />
<br />
::The external wires of the printer are hold in a cable chain. This way the cables are kept orderly and safe while the axis are moving.<br />
|-<br />
|}<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION socket.jpeg|150px|thumb|Socket with switch]] ||<br />
::Two connectors are situated on the back side, one for the AC power supply through a socket with switch and one for USB connections in case you wish to control the printer directly from your PC.<br />
<br />
::The housing features also an opening and bores for a Raspberry Pi 2 (not included) which allows to connect the printer to the internet and control it via Octoprint.<br />
|-<br />
|}<br />
<br />
<br />
{| <br />
|-<br />
| [[File:Prusai3 ION LCD.jpeg|150px|thumb|LCD 2004 screen]] ||<br />
::Optionally, you can purchase a LCD 2004 screen for monitoring the printer. The screen controller includes a SD card that allows to load designs without the need for a PC.<br />
<br />
::There is no need to modify the firmware for the display’s setup. With this board you can control the printing speed without having to wait for the hotend to cool down, preheat the printer, modify the firmware’s parameters, or change filament in the middle of the printing process; all this without a PC.<br />
|-<br />
|}<br />
<br />
=Where to buy=<br />
<br />
- [http://store.thingibox.com/es/prusa-i3-ion/192-Prusa_i3_ION_kit_completo.html Complete Kit in ThingiBOX] Now Available!</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Clone_wars:_Tiendas_en_barcelona&diff=150103Clone wars: Tiendas en barcelona2015-06-17T09:04:05Z<p>Merlucin: </p>
<hr />
<div>* [http://www.transmisiones.com/ transmisiones.com]: Venden correas T5 y T2.5<br />
* [http://bcndynamics.com/es/ BCN Dynamics]: Venden todos los componentes de impresoras 3D y kits. Tienda en Barcelona: c/ Sepúlveda, 61-63.<br />
* [http://www.castellsvilaseca.com/ Hierros Castellsvilaseca]:Barra de acero calibrada de 3metros AISI 304L a unos 12€ (Cobran 1€ por cada corte)<br />
* [http://printhatshit.com/ PRINTHATSHIT - Easy 3D printing -]: Venden lo mismo que en su web y organizan talleres de montaje. Tienda en Barcelona, junto a Sants Estació.<br />
* [http://store.thingibox.com/ ThingiBOX]: Puedes recoger en su oficina el pedido realizado en la web y ahorrar los gastos de envío. Tienda en Viladecans, cerca de la estación de tren.<br />
<br />
{| class="wikitable"<br />
|-<br />
|<br />
[[File:Clone-Wars-logo.png|border|100px|link=Proyecto Clone Wars]]<br />
| [[Proyecto Clone Wars]]<br />
|}<br />
<br />
[[Category:Clone wars/es]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Talk:RepRap_Buyers%27_Guide&diff=149948Talk:RepRap Buyers' Guide2015-06-12T15:53:20Z<p>Merlucin: /* How to get included into the RepRap Buyers' Guide */</p>
<hr />
<div>Remember guys, neutral voice, this is a wiki, not a Flea Market. -Neil/Spacexula<br />
<br />
== How to get included into the RepRap Buyers' Guide ==<br />
<br />
It's simple: please add your entry here in a new line. Take care to set to set your country right and also to put checkmarks (only) where they fit. Admins watch this talk page and will take the entry over to the main page after a review.<br />
<br />
In case you aren't allowed to add external links (you'll notice that), put a space between the slashes of the link, like http:/ /example.com . The Admin will fix them when moving the entry over to the main page.<br />
<br />
<br />
{| class="wikitable sortable"<br />
|- style="background-color:#f0f0f0;"<br />
! style="vertical-align: bottom;" | Vendor<br />
! style="vertical-align: bottom;" | Loc.<br />
! {{Vertical|2em|12em|&nbsp;Full&nbsp;Printer&nbsp;Kits}}<br />
! {{Vertical|2em|12em|&nbsp;Printed&nbsp;Parts&nbsp;Kits}}<br />
! {{Vertical|2em|12em|&nbsp;Electronics&nbsp;Kits}}<br />
! {{Vertical|2em|12em|&nbsp;Extruder/Hotends}}<br />
! {{Vertical|2em|12em|&nbsp;Heated&nbsp;Beds}}<br />
! {{Vertical|2em|12em|&nbsp;Steppers}}<br />
! {{Vertical|2em|12em|&nbsp;Smooth/threaded&nbsp;Rods }}<br />
! {{Vertical|2em|12em|&nbsp;Filaments}}<br />
! {{Vertical|2em|12em|&nbsp;Misc.}}<br />
! style="vertical-align: bottom;" | Developers of ...<br />
! style="vertical-align: bottom;" class="unsortable" | Reviews and notes<br />
|-<br />
| [http://example-shop.com Example Shop] || AQ <br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; ||&#x2713; ||&#x2713; ||&#x2713;||&#x2713;<br />
| Miscellaneous|| &lt;your genuine development(s), if any, here&gt; || reviews go here (third party only)<br />
|-<br />
| [http://www.thingibox.com ThingiBox] || ES <br />
| || || &#x2713; || &#x2713; ||&#x2713; ||&#x2713; ||&#x2713;||&#x2713;<br />
| Bearings, Accessories and other parts|| [https://github.com/Thingibox/ Prusa i3 ION] || <br />
|-<br />
|}<br />
<br />
-moved over and sorted the list out 23/4/2014 - thejollygrimreaper<br />
-moved over and sorted the list out 22/6/2014 - thejollygrimreaper<br />
-Moved over to main list 12/11/2014 - thejollygrimreaper<br />
-list sorted 30/11/2014 - --[[User:Thejollygrimreaper|Thejollygrimreaper]] ([[User talk:Thejollygrimreaper|talk]]) 15:49, 29 November 2014 (PST)<br />
-moved over --[[User:Thejollygrimreaper|Thejollygrimreaper]] ([[User talk:Thejollygrimreaper|talk]]) 17:40, 3 December 2014 (PST)<br />
-moved over --[[User:Thejollygrimreaper|Thejollygrimreaper]] ([[User talk:Thejollygrimreaper|talk]]) 03:34, 15 December 2014 (PST)<br />
-moved over --[[User:Thejollygrimreaper|Thejollygrimreaper]] ([[User talk:Thejollygrimreaper|talk]]) 23:44, 16 January 2015 (PST)<br />
-moved over --[[User:Thejollygrimreaper|Thejollygrimreaper]] ([[User talk:Thejollygrimreaper|talk]]) 18:34, 24 April 2015 (PDT)<br />
-moved over --[[User:Thejollygrimreaper|Thejollygrimreaper]] ([[User talk:Thejollygrimreaper|talk]]) 04:52, 15 May 2015 (PDT)<br />
<br />
== Makerbot? ==<br />
<br />
Does it still make sense to list Makerbot here ?<br />
They do not do open-hardware anymore, they are pretty hostile to the community, and the only few parts they carry that could be useful in building a reprap are hobbed bolts and a few other random vitamins. --[[User:Arthurwolf|Arthurwolf]] ([[User talk:Arthurwolf|talk]]) 02:27, 9 December 2014 (PST)<br />
<br />
== various pages that list sellers ==<br />
<br />
There seem to be a bunch of wiki pages that list places where people can buy stuff related to building a RepRap (raw materials and "vitamins") or a RepStrap.<br />
<br />
* [[Mendel Buyers Guide]]<br />
* [[Mendel materials procurement]]<br />
* [[Mendel assembly data sheet]]<br />
* [[PartsSupplies]]<br />
* [[Suppliers]]<br />
* [[Frame material]]<br />
* [[Extruded Aluminum]]<br />
<br />
Should we merge some of these pages together?<br />
Or put an explanation on one of these pages that lists all the pages why each one exists?<br />
--[[User:DavidCary|DavidCary]] 03:07, 11 April 2010 (UTC)<br />
<br />
Hey guys! a bunch of useful information disappearred just now. Specifically, McMaster Carr entry had links to two specific steel rods. They were the cheapest in my area and they delivered them the same day. Are these not suitable anymore? --[[user: Prof_Braino]] Sept 17<br />
<br />
== Please update the table listing for 3dbotshack.com ==<br />
We have added Hobbed Bolts (information can be found here http://3dbotshack.com/hobbedbolt.html ) and MK1 Heated Beds (info can be found here http://3dbotshack.com/3dprinterpcbheatbed.html ).<br />
<br />
<br />
== How to support developers even better ==<br />
<br />
Following the discussion about TrinityLabs above, I'd appreciate a discussion on how to support RepRap developers even better. The "Developer of..." column is new in this revision of the guide and meant to distinguish shops just copying openly available developments (I tend to call then "copy shops") from those who also do active development for the RepRap community. Now [[User:ArthurWolf]] has brought up shops which don't do their own development, but "support" development. I guess, "support" means something like paying a fee per product sold or ordering shop supplies not at a manufacturer, but from the developer.<br />
<br />
As shops supporting development are undoubtly more valueable for the community, maybe even essential for the community to survive as an independent one, how can we get this into the picture? What's the measurement to avoid checkmark hunters (like e.g. donating $0.10 per product sold, just to get the check mark) versus highlighting noticeable support? Can we perhaps call out one of the support strategies to be a recommended standard for RepRap shops?<br />
<br />
--[[User:Traumflug|Traumflug]] 20:18, 14 June 2013 (UTC)<br />
<br />
: P.S.: After writing this ArthurWolf explained the situation: TrinityLabs is actually one of several of the [[SmoothieBoard]] developers (so far I considered him to be the only one), but he also asked to forward this to another admin, so I keep my hands still. Nevertheless I think the general scope of the topic here deserves a discussion. --[[User:Traumflug|Traumflug]] 20:41, 14 June 2013 (UTC)<br />
<br />
Perhaps as a first step in this direction, each row could name the developer(s) who designed the products they are selling? For example, if a shop sold the original, unmodified [[Darwin]], that row would credit Adrian Bowyer. More recent machines would typically credit at least 3 people (the mechanical structure designer, the electronics designer, and the software programmer) and previous designers whose work they built on. --[[User:DavidCary|DavidCary]] 17:57, 25 August 2013 (UTC)<br />
: Might become tricky, because shops not selling their own developments tend to sell many different designs. Regarding electronics and firmware I'd be very happy to see this recognized as separate itmes. You can drive a Mendel with about any electronics and many firmwares; the smae is true for about any printer design. Printer designs should just list the required features of the controlling electronics instead of prefering a specific one. --[[User:Traumflug|Traumflug]] 10:47, 26 August 2013 (UTC)<br />
<br />
<br />
== Reviews shouldn't be from shop owners, but for customers ==<br />
<br />
Some of «Reviews and notes» are filled by shop owners; this is bad because isn't factual. Same for price, because shop owners will not be able to edit and update this information directly. --[[User:XoanSampaiño|Xoan Sampaiño]] ([[User talk:XoanSampaiño|talk]]) 21:27, 23 June 2014 (PDT)<br />
<br />
== listing update ==<br />
9/2/2015- moved over, if i missed any add them to the list at the top of the page --[[User:Thejollygrimreaper|Thejollygrimreaper]] ([[User talk:Thejollygrimreaper|talk]]) 01:34, 9 February 2015 (PST)</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Talk:RepRap_Buyers%27_Guide&diff=149839Talk:RepRap Buyers' Guide2015-06-09T10:34:11Z<p>Merlucin: /* How to get included into the RepRap Buyers' Guide */</p>
<hr />
<div>Remember guys, neutral voice, this is a wiki, not a Flea Market. -Neil/Spacexula<br />
<br />
== How to get included into the RepRap Buyers' Guide ==<br />
<br />
It's simple: please add your entry here in a new line. Take care to set to set your country right and also to put checkmarks (only) where they fit. Admins watch this talk page and will take the entry over to the main page after a review.<br />
<br />
In case you aren't allowed to add external links (you'll notice that), put a space between the slashes of the link, like http:/ /example.com . The Admin will fix them when moving the entry over to the main page.<br />
<br />
<br />
{| class="wikitable sortable"<br />
|- style="background-color:#f0f0f0;"<br />
! style="vertical-align: bottom;" | Vendor<br />
! style="vertical-align: bottom;" | Loc.<br />
! {{Vertical|2em|12em|&nbsp;Full&nbsp;Printer&nbsp;Kits}}<br />
! {{Vertical|2em|12em|&nbsp;Printed&nbsp;Parts&nbsp;Kits}}<br />
! {{Vertical|2em|12em|&nbsp;Electronics&nbsp;Kits}}<br />
! {{Vertical|2em|12em|&nbsp;Extruder/Hotends}}<br />
! {{Vertical|2em|12em|&nbsp;Heated&nbsp;Beds}}<br />
! {{Vertical|2em|12em|&nbsp;Steppers}}<br />
! {{Vertical|2em|12em|&nbsp;Smooth/threaded&nbsp;Rods }}<br />
! {{Vertical|2em|12em|&nbsp;Filaments}}<br />
! {{Vertical|2em|12em|&nbsp;Misc.}}<br />
! style="vertical-align: bottom;" | Developers of ...<br />
! style="vertical-align: bottom;" class="unsortable" | Reviews and notes<br />
|-<br />
| [http://example-shop.com Example Shop] || AQ <br />
| &#x2713; || &#x2713; || &#x2713; || &#x2713; ||&#x2713; ||&#x2713; ||&#x2713;||&#x2713;<br />
| Miscellaneous|| &lt;your genuine development(s), if any, here&gt; || reviews go here (third party only)<br />
|-<br />
| [http://www.thingibox.com ThingiBox] || ES <br />
| || || &#x2713; || &#x2713; ||&#x2713; ||&#x2713; ||&#x2713;||&#x2713;<br />
| Bearings, Accessories and other parts|| Prusa i3 ION || <br />
|-<br />
|}<br />
<br />
-moved over and sorted the list out 23/4/2014 - thejollygrimreaper<br />
-moved over and sorted the list out 22/6/2014 - thejollygrimreaper<br />
-Moved over to main list 12/11/2014 - thejollygrimreaper<br />
-list sorted 30/11/2014 - --[[User:Thejollygrimreaper|Thejollygrimreaper]] ([[User talk:Thejollygrimreaper|talk]]) 15:49, 29 November 2014 (PST)<br />
-moved over --[[User:Thejollygrimreaper|Thejollygrimreaper]] ([[User talk:Thejollygrimreaper|talk]]) 17:40, 3 December 2014 (PST)<br />
-moved over --[[User:Thejollygrimreaper|Thejollygrimreaper]] ([[User talk:Thejollygrimreaper|talk]]) 03:34, 15 December 2014 (PST)<br />
-moved over --[[User:Thejollygrimreaper|Thejollygrimreaper]] ([[User talk:Thejollygrimreaper|talk]]) 23:44, 16 January 2015 (PST)<br />
-moved over --[[User:Thejollygrimreaper|Thejollygrimreaper]] ([[User talk:Thejollygrimreaper|talk]]) 18:34, 24 April 2015 (PDT)<br />
-moved over --[[User:Thejollygrimreaper|Thejollygrimreaper]] ([[User talk:Thejollygrimreaper|talk]]) 04:52, 15 May 2015 (PDT)<br />
<br />
== Makerbot? ==<br />
<br />
Does it still make sense to list Makerbot here ?<br />
They do not do open-hardware anymore, they are pretty hostile to the community, and the only few parts they carry that could be useful in building a reprap are hobbed bolts and a few other random vitamins. --[[User:Arthurwolf|Arthurwolf]] ([[User talk:Arthurwolf|talk]]) 02:27, 9 December 2014 (PST)<br />
<br />
== various pages that list sellers ==<br />
<br />
There seem to be a bunch of wiki pages that list places where people can buy stuff related to building a RepRap (raw materials and "vitamins") or a RepStrap.<br />
<br />
* [[Mendel Buyers Guide]]<br />
* [[Mendel materials procurement]]<br />
* [[Mendel assembly data sheet]]<br />
* [[PartsSupplies]]<br />
* [[Suppliers]]<br />
* [[Frame material]]<br />
* [[Extruded Aluminum]]<br />
<br />
Should we merge some of these pages together?<br />
Or put an explanation on one of these pages that lists all the pages why each one exists?<br />
--[[User:DavidCary|DavidCary]] 03:07, 11 April 2010 (UTC)<br />
<br />
Hey guys! a bunch of useful information disappearred just now. Specifically, McMaster Carr entry had links to two specific steel rods. They were the cheapest in my area and they delivered them the same day. Are these not suitable anymore? --[[user: Prof_Braino]] Sept 17<br />
<br />
== Please update the table listing for 3dbotshack.com ==<br />
We have added Hobbed Bolts (information can be found here http://3dbotshack.com/hobbedbolt.html ) and MK1 Heated Beds (info can be found here http://3dbotshack.com/3dprinterpcbheatbed.html ).<br />
<br />
<br />
== How to support developers even better ==<br />
<br />
Following the discussion about TrinityLabs above, I'd appreciate a discussion on how to support RepRap developers even better. The "Developer of..." column is new in this revision of the guide and meant to distinguish shops just copying openly available developments (I tend to call then "copy shops") from those who also do active development for the RepRap community. Now [[User:ArthurWolf]] has brought up shops which don't do their own development, but "support" development. I guess, "support" means something like paying a fee per product sold or ordering shop supplies not at a manufacturer, but from the developer.<br />
<br />
As shops supporting development are undoubtly more valueable for the community, maybe even essential for the community to survive as an independent one, how can we get this into the picture? What's the measurement to avoid checkmark hunters (like e.g. donating $0.10 per product sold, just to get the check mark) versus highlighting noticeable support? Can we perhaps call out one of the support strategies to be a recommended standard for RepRap shops?<br />
<br />
--[[User:Traumflug|Traumflug]] 20:18, 14 June 2013 (UTC)<br />
<br />
: P.S.: After writing this ArthurWolf explained the situation: TrinityLabs is actually one of several of the [[SmoothieBoard]] developers (so far I considered him to be the only one), but he also asked to forward this to another admin, so I keep my hands still. Nevertheless I think the general scope of the topic here deserves a discussion. --[[User:Traumflug|Traumflug]] 20:41, 14 June 2013 (UTC)<br />
<br />
Perhaps as a first step in this direction, each row could name the developer(s) who designed the products they are selling? For example, if a shop sold the original, unmodified [[Darwin]], that row would credit Adrian Bowyer. More recent machines would typically credit at least 3 people (the mechanical structure designer, the electronics designer, and the software programmer) and previous designers whose work they built on. --[[User:DavidCary|DavidCary]] 17:57, 25 August 2013 (UTC)<br />
: Might become tricky, because shops not selling their own developments tend to sell many different designs. Regarding electronics and firmware I'd be very happy to see this recognized as separate itmes. You can drive a Mendel with about any electronics and many firmwares; the smae is true for about any printer design. Printer designs should just list the required features of the controlling electronics instead of prefering a specific one. --[[User:Traumflug|Traumflug]] 10:47, 26 August 2013 (UTC)<br />
<br />
<br />
== Reviews shouldn't be from shop owners, but for customers ==<br />
<br />
Some of «Reviews and notes» are filled by shop owners; this is bad because isn't factual. Same for price, because shop owners will not be able to edit and update this information directly. --[[User:XoanSampaiño|Xoan Sampaiño]] ([[User talk:XoanSampaiño|talk]]) 21:27, 23 June 2014 (PDT)<br />
<br />
== listing update ==<br />
9/2/2015- moved over, if i missed any add them to the list at the top of the page --[[User:Thejollygrimreaper|Thejollygrimreaper]] ([[User talk:Thejollygrimreaper|talk]]) 01:34, 9 February 2015 (PST)</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=FoldaRap_Buyers_Guide&diff=149696FoldaRap Buyers Guide2015-06-01T18:05:05Z<p>Merlucin: /* Laser cut parts */</p>
<hr />
<div>{{Languages|FoldaRap Buyers Guide}}<br />
{{RepRapNavigation|name=FoldaRap}}<br />
<br />
This project was for myself, as I need/want a RepRap that's easy to carry around and for the challenge of making a folding 3d-printer.<br />
But I believe in open-source and sharing and all the revolution behind that. Thus I try to well document it, in case others want to make one; to acknowledge all the things we own to those who went before, and to encourage those who come after to do the same.<br />
<br />
On a more long-term view, I didn't planned to create a company out of it, I hoped to see it grow on itself in the wild, just by indicating how to source it, because I have more fun in designing stuff than marketing it. Nonetheless I may try to sell few beta-test kits (bulk ordering is good for prices), eventually via a crowdfunding campaign or by request, maybe with the help of my hackerspace. Just for the experience of it and to say I can push a project to that point :D<br />
(edit : [http://ulule.com/foldarap/ Done !], [http://goteo.org/project/foldarap-peer-to-peer-edition again], and it finally gave birth to ''[http://openedge.cc/ Open Edge]'')<br />
<br />
(almost all the projects I did during my design studies could have done something, but I never found the time for that and they ended sleeping in their drawing books which is sad; while now I have taken the habit to publish everything, even an old one sometimes).<br />
<br />
"Ideas are like living things and breed happily in an open-source context" as I like to think ^^ (on the same spirit I like [http://www.makerbot.com/blog/2012/09/20/fixing-misinformation-with-information/#comment-38041 this comment] from [[User:Adrianbowyer]])<br />
<br />
==Bill Of Material (BOM)==<br />
Total end cost for 1 machine : ~500-600€ when you include all taxes and shipping costs. I suggest you to make group orders with friends and always try to source locally, or now for almost the same price I can make a kit for you.<br />
<br />
===Hardware===<br />
<br />
[[File:Foldarap_hardware-kit.jpg|250px]]<br />
5 20x20mm beam 6mm slot 200mm - [http://www.motedis.com/shop/Slot-profiles/Profile-20-B-Type-slot-6/Profile-20x20-B-type-slot-6::1.html Motedis] or see [[Aluminium profile]]<br />
6 20x20mm beam 6mm slot 300mm<br />
54 M4 T-nut for 6mm slot - [http://www.motedis.com/shop/Slot-profiles-accessories/Accessoiries-20-B-Typ-slot-6/T-nut-B-type-slot-6::555.html Motedis]<br />
<br />
54 m4x8 round head bolt - [http://www.visseriefixations.fr/catalog/product/view/id/1496/s/tbhc-m4x8-z-blanc-iso-7380/ Fix'n Vis Round Head Bolt]<br />
4 m5 nylon nut / Z-rod (4) [http://www.visseriefixations.fr/catalog/product/view/id/13095/s/ecrou-hu-m5-pa6-6-blanc-din-555/]<br />
3 m3 nylock nut / bed leveling (3) [http://www.visseriefixations.fr/ecrous/ecrous-autofreines/ecrou-hexagonal-autofreine-bague-nylon/ecrou-nylstop-acier-zingue-blanc-din-985.html nylock nut]<br />
15 m3 nut / hinges (2), bed (3), Y-belt-clamp (2), extruder (2), plug (2), psu (4) - [http://www.visseriefixations.fr/ecrous/ecrous-hexagonaux/ecrou-hexagonal-hu/acier-zingue-blanc/ecrou-hu-acier-zingue-blanc-classe-8-din-934.html Fix'n Vis Nuts]<br />
14 m3x8 bolt / Z-motors (4), Y-motor (2), psu (2), male plug (2), board-mount (2), hotend (2) - [http://www.visseriefixations.fr/vis-a-six-pans-creux/tete-cylindrique-hexagonale-creuse/acier-8-8-zingue-blanc/tchc-acier-8-8-zingue-blanc-filetage-total-din-912.html Fix'n Vis Bolts]<br />
8 m3x10 bolt / hotend (4), y-belt-clamp (2), extruder (2)<br />
1 m3x16 bolt / extruder (1)<br />
4 m3x20 bolt / hinges (2), Y-idler (1), extruder (1)<br />
5 m3x25 bolt / hotend-holder (2), fan-holder (1), (extruder 1), z-endstop (1)<br />
4 m3x30 bolt / x-slider (4)<br />
3 m3x30 countersunk bolt / bed (3)<br />
2 m3x35 / extruder (2)<br />
2 230mm threaded rod m5 - [http://www.visseriefixations.fr/catalog/product/view/id/8626/s/tige-filetee-m5-inox-a2-din-975.html Fix'n Vis]<br />
<br />
2 extruder spring - [http://www.rs-particuliers.com/web/p/ressorts-de-compression/751483/ RS751483] or see [[Springs]]<br />
3 bed spring - [http://ssl.rs-particuliers.com/web/p/ressorts-de-compression/751455/ RS 751455] or [http://ssl.rs-particuliers.com/web/p/ressorts-de-compression/751607/ RS 751607]<br />
1m spiral wrapping band for tidying the wires - [http://www.rs-particuliers.com/WebCatalog/Cable_De_Retention_Polythene_6mm_Dia-227974.aspx RS227874]<br />
7 6,35mm ferule - [http://www.rs-particuliers.com/WebCatalog/Borne_Femelle_%C3%80_Sertir_6_35mm_18_14awg-6831456.aspx Radiospare] to crimp the cable for the plug and the switch<br />
<br />
2 5mm to 5mm flexible coupling<br />
3 linear bearing, LM6UU or if you can Igus RJMP-01-06 - See [[Bearing]]<br />
2 300mm smooth rod 6mm - (can be salvaged from usual scanners and printers) or see [[Smooth rod]]<br />
5 603zz bearings / X-slider (2), Y-idler (2), extruder-idler (1) - See [[Bearing]]<br />
1 250mm T2.5 belt 5mm wide - [http://reprapworld.com/?products_details&products_id=175&cPath=1595_1611 RepRapWorld] or see [[Belts_and_Pulleys]]<br />
1 600mm T2.5 belt 5-6mm wide<br />
2 T2.5 pulleys - [[Belts_and_Pulleys]]<br />
330mm PTFE Tubing for bowden extruder (2mm inner diam. and 3mm outer) - See [[Bowden]]<br />
2 Pneumatic fittings for 3mm tubing, with M5 thread - See [[Bowden]] or [http://www.emakershop.com/browse/listing?l=237 emakershop] / I'm using the MA12-03-M5 but others can work<br />
1 direct drive gear - Maritime-models (see [[Drive-gear]])<br />
1 roll of kapton - See [[Kapton Tape#Vendors]]<br />
20 zip-ties<br />
<br />
===Electronic===<br />
5 nema14 stepper motors - [http://www.zappautomation.co.uk/sy35st36-1004a-high-torque-hybrid-stepper-motors.html]<br />
3 miniature microswitch endstop 20mm - [http://www.emakershop.com/listing?l=128]<br />
1 standard male plug IEC C13 C14 - [http://www.rs-particuliers.com/WebCatalog/Prise_Cei__A_Visser_6_3mm_Faston_1_5mm-5392045.aspx RS 5392045]<br />
1 standard female cable - [http://www.indipc.fr/connectique,cable-fiche-alimentation-secteur-prise-schuko-nf-10-16a-h05vv-f-3x0-75-1m80-1m80,cordon-alimentation,page,zoom,mod,boutique,gps,57659-524.fr.html EU/C13] - [http://www.rs-particuliers.com/WebCatalog/Cordon_Anglais_Cee_2p_t_25m-6266739.aspx UK RS6266739] / [http://www.rs-particuliers.com/Product.aspx?Product=7316163 US RS7316163]<br />
1 big blue switch - [http://www.rs-particuliers.com/Product.aspx?Product=5287858 RS 5287858]<br />
1 RepRappro Hotend - [http://www.emakershop.com/browse/listing?l=320 emaker]<br />
1 40x40mm heatsink - [http://www.rs-particuliers.com/WebCatalog/Dissipateur_Ick_Bga_40x40x10-6744769.aspx RS 6744769] to make a more compact hotend<br />
1-2 small fan (40 x 40 x 10 mm), for the hotend (can be bought with one) and the extruder motor - [http://reprapworld.com/?products_details&products_id=171 RepRapWorld] or see [[Fan]]<br />
1 100k thermistors - [http://fr.mouser.com/Search/ProductDetail.aspx?R=AL03006-58.2K-97-G1virtualkey52710000virtualkey527-AL3006-100K Mouser]<br />
1m of 18AWG wire (200mm red, 200m black, 150mm green) for the switch/plug/psu - Read also [[WiresAndConnectors]]<br />
10m of 26AWG (3.6m red, 3.2m green, 2.0m blue) for the sensors and fans<br />
<br />
1 Minitronic board [http://reprapworld.com/?products_details&products_id=359&cPath=1591_1647]<br />
1 USB cable A to B [http://reprapworld.com/?products_details&products_id=59&cPath=1591_1647]<br />
1 12V power supply : [http://www.ebay.com/itm/121029223528 5A] (cold bed) or [http://www.ebay.com/itm/261295101016 10A] or [http://www.ebay.com/itm/221266614995] (for heated bed)<br />
<br />
or<br />
<br />
1 [[Azteeg_X1]] board - [http://www.panucatt.com/azteeg_X1_reprap_3d_printer_controller_p/ax13dp.htm] + 4 drivers<br />
1 usb to mini-usb cable - [http://www.indipc.fr/informatique,usb-2-0-type-mini-b,connectique,page,boutique,mod,boutique,gps,5104.fr.html]<br />
1 12V power supply : [http://www.ebay.com/itm/300739370622 10A]<br />
<br />
or<br />
<br />
1 Rumba + 6 stepper drivers<br />
1 usb to mini-usb cable<br />
1 12V power supply : [http://www.rs-particuliers.com/WebCatalog/Alimentation_%C3%80_Decoupage_12v_20a_240w-7066316.aspx 20A] (RS 7066316 100*150*35mm)<br />
<br />
====Heated-Bed====<br />
For the aluminium heated bed add :<br />
<br />
1 aluminium bed plate (4mm thick)<br />
<br />
1 kapton film heater - [http://openedge.cc/product/kapton-film-heater/ Open Edge]<br />
<br />
or<br />
<br />
1 100k thermistors - [http://fr.mouser.com/Search/ProductDetail.aspx?R=AL03006-58.2K-97-G1virtualkey52710000virtualkey527-AL3006-100K Mouser]<br />
2 ferule 0,5mm²<br />
1 peltier element 12708 (40x40mm is enough) - [http://www.ebay.com/sch/i.html?_trksid=p3984.m570.l1313&_nkw=TEC+12708&_sacat=0&_from=R40 ebay]<br />
<br />
===Laser cut parts===<br />
<gallery perrow=4 widths=200px heights=150px><br />
Foldarap2_underplate.jpg|underplate 3-4mm thick<br />
Foldarap_y-carriage_lasercut.jpg|y-carriage 3mm thick<br />
Foldarap_reprap-plate.jpg|reprap.org plate 160x20mm 2-4mm thick / Optionnal but make a nice reference to the wiki :)<br />
</gallery><br />
<br />
See the [https://github.com/EmmanuelG/Foldarap/tree/master/hardware/2D%20drawings github repo] and [http://www.emakershop.com/browse/listing?l=204 eMakerShop], you can have them from [http://www.ponoko.com/showroom/Watsdesign Ponoko] or [http://store.thingibox.com/en/foldarap/95-foldarap_lasercut_pieces.html ThingiBOX] too<br />
<br />
The bed can also be made of acrylic in case of a non-heated bed.<br />
<br />
[[File:FoldaRap_bed-plate_1.1.jpg|400px]]<br />
<br />
===Printed parts (total : 21)===<br />
See also the [https://github.com/EmmanuelG/Foldarap/tree/master/hardware/stl github repo]<br />
<br />
<gallery perrow=4 widths=200px heights=150px><br />
Foldarap2_foot-front-left.jpg|foot-front left<br />
Foldarap2_foot-front-right.jpg|foot-front right<br />
Foldarap2_foot-rear-left.jpg|foot-rear left<br />
Foldarap2_foot-rear-right.jpg|foot-rear right<br />
Foldarap2_hinge-outer-left.jpg|hinge-outer left<br />
Foldarap2_hinge-outer-right.jpg|hinge-outer right<br />
Foldarap2_hinge-inner-left.jpg|hinge-inner left<br />
Foldarap2_hinge-inner-right.jpg|hinge-Inner right<br />
Foldarap2_z-motor-bracket-left.jpg|z-motor-bracket left<br />
Foldarap2_z-motor-bracket-right.jpg|z-motor-bracket right<br />
Foldarap2_z-top-left.jpg|z-top left<br />
Foldarap2_z-top-right.jpg|z-top right<br />
FoldaRap_y-idler_603zz.jpg|y-idler<br />
Foldarap_belt-clamp.jpg|belt-clamp<br />
Foldarap_y-motor.jpg|y-motor<br />
Foldarap2_extruder-left_nema14.jpg|extruder left<br />
Foldarap2_Z-slider-left.jpg|z-slider left<br />
Foldarap2_Z-slider-right.jpg|z-slider right<br />
Foldarap2_extruder-right_nema14.jpg|extruder right<br />
Foldarap2_X-slider.jpg|x-slider<br />
FoldaRap2_X-slider_hotend-holder.jpg|hotend-holder<br />
FoldaRap2_X-slider_fan-holder.jpg|fan holder<br />
Foldarap_board-mount.jpg|board mounts<br />
FoldaRap-handle.jpg|handle<br />
FoldaRap_spool-holder.jpg|spool-holder<br />
</gallery><br />
<br />
===Other===<br />
<br />
====Padded suitcase====<br />
*EU : http://www.abylon.fr/145-valise-olycase-500.html<br />
*FR : http://www.vexi.fr/valises-plastique/etanches<br />
*US : http://www.amazon.com/Nanuk-Case-Cubed-Foam-Black/dp/B003JH7ZU4/<br />
<br />
==== Maintenance ====<br />
*0.3mm drill bit [http://www.ebay.com/sch/i.html?_trksid=m570.l3201&_nkw=0.3mm+drill+bit+tamiya&_sacat=0] (or 0.5mm, depending of the nozzle)<br />
<br />
==How to replicate a FoldaRap !==<br />
If you can print your own parts it will take ~400gr and 22h at ~30% infill.<br />
<br />
===Material===<br />
The parts that act as sliders on the aluminium extrusions (x-slider, z-sliders) will work better if printed in PLA or other low friction plastic.<br />
You can print the other parts in ABS or what you want.<br />
<br />
===Recommended settings===<br />
*Nozzle diameter of reference : 0,5 mm<br />
*Layer height : 0,25mm<br />
*Infill : 30-35% ''hexagonal/honeycomb''<br />
*It is advised to have a well calibrated machine (+/- 0.05mm on measured parts) : http://forums.reprap.org/read.php?282,159683<br />
<br />
[[File:30percenthexainfill.jpg|500px]][[File:25percent-rectilinear-infill_slicer.jpg|500px]]<br />
<br />
[[File:foldarap_precision-needed.jpg|500px]][[File:Reprapworld-black-print2.jpg|500px]][[File:Reprapworld-black-print.jpg|500px]]<br />
<br />
I recorded this little video where I'm playing with some parts freshly printed, to show what to expect about the tight tolerances.<br />
<br />
<videoflash>rRXyc5I8yfo</videoflash><br />
<br />
The part that slide under it's own weight (16gr) have been slided back and forth a few time.<br />
<br />
==Fully assembled machines==<br />
Not yet.<br />
<br />
==Partial or complete kit==<br />
*[http://openedge.eu OpenEdge]<br />
<br />
==Webshops==<br />
*[http://www.paoparts.com/fr/36-foldarap Paoparts] (out of stock)<br />
<br />
===Printed parts===<br />
*[http://www.emakershop.com/browse/listing?l=559 Spares 3d on eMakerShop] (1.1)<br />
*[http://www.emakershop.com/browse/listing?l=708 3d Andy on eMakerShop] (1.1 + geared extruder) (sold out)<br />
<br />
==Misc.==<br />
*A draft BOM is on [http://kitbom.com/EmmanuelG/foldarap Kitbom]<br />
*My [[media:FoldaRap_BOM_data_sheet.ods|spreadsheet]] is roughly the same as the following lists but a little outdated.<br />
<br />
<br />
==FoldaRapMendel Bom==<br />
[[File:Foldarap-Mendel_00.jpg|300px]]<br />
<br />
1 underplate<br />
<br />
6 300 mm<br />
6 400 mm<br />
<br />
50 M4x8<br />
8 M4x12 (hinges)<br />
2 M4x16 (hinges)<br />
<br />
[[Category:Foldable RepRap]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=FilamentReviews_Qingdao_TSD_Plastic_Co&diff=145089FilamentReviews Qingdao TSD Plastic Co2015-02-23T15:22:55Z<p>Merlucin: New review from TSD plastic</p>
<hr />
<div>{| class="wikitable sortable"<br />
|+ ''Reviews'' for: [http://qdtsd.en.alibaba.com/productgrouplist-210256164/Plastic_Welding_rods.html#products Qingdao TSD Plastic Co., Ltd.] <br />
([[FilamentNewCompanyReviewTemplate|Template]])<br />
<br><br />
Back to [[Printing_Material_Suppliers|Filament Suppliers]].<br />
<br><br><br />
<br><br>([[FilamentNewAnswerEntry|Answer Template]])<br />
|- style="background-color:#f0f0f0;"<br />
! Date !! Material(s) !!Shape/Delivered!!Thickness (mm)!!Measured thickness (mm)!!Quantity!!Delivered amount!!Costs (kg)!!Costs (Meter)!!Destination & shipping costs!!Rating 0-10!! Additional notes & Signed by<br />
|-<br />
<br />
| 23. July 2011||[[ABS]]||Round||3mm||3.14/3.03/3.42||21Kg||TODO||$16.15usd/kg||-||Incl. in cost.||-||The filament is full of '''0.5-1.0mm air bubbbles''', surface is '''marred and not smooth'''. Delivery was delayed, was tols a machine has broken down but this batch was from after the repairs.<br />
-[[User:MarcusWolschon|Marcus Wolschon]].<br />
|-<br />
|02. June 2011||[[ABS]]||Round/oval||3mm||2.5,2.7,3.0,2.8,2.9,3.2,3.3,3.4||21kg||18.627kg||$16.77/kg||-||Incl. in cost||-||Other: The filament had oil on it some places from the manufacturing process. <br />
-[[User:ROTORIT|ROTORIT]].<br />
|-<br />
|07. March 2013||[[ABS]]||Round||1.75mm||1.65mm with STD 0.05 min 1.53 max 1.73 ||20kg||18.627kg||$16.77/kg||-||Incl. in cost||-||Material had lots of bubbles that combined with the small diameter made the material unprintable. When I complained about the diameter, the sales guy "John" claimed that despite the PO, they "shipped me 1.65 mm because 1.65 is better for printing." They will lie to you about everything. Not a reputable supplier.<br />
<br />
Update: After I posted the review, they were nice enough to send another roll for testing. This roll had similar measurements as the first. 1.64 mm +/- 0.5 mm. If your printer takes 1.65 mm nominal, it may work for you. Using a makergear, the filament is too thin to feed. Perhaps if you have something that can deal with the smaller diameter and the air bubbles, it will work for you.<br />
-[[User:Pinkyxjmmb|Pinkyxjmmb]].<br />
<br />
They had already advanced the quality, no bubbles at 235degree, and the diameter difference is about +/-0.06mm which works well for my printer. I have to say that they have a excellent package, vaccum packed in plastic bag with desiccant and have small box for each spool. I will continue to buy from Qingdao TSD Plastic. The price is 19usd/kg and quantity is 25kg.<br />
-[[User:Rak|Rak]].<br />
<br />
|-<br />
|15 December 2015||[[ABS / PLA / HIPS]]||Round||1.75mm / 3mm||1.72mm / 2.95mm (+/- 0.2mm) ||30kg||$18/kg||17$/kg||-||Incl. in cost||-||We have been ordering material from TSD plastic since 2006 mainly because the price was very competitive. At the beginning the quality of the filament was poor, but in the last years it became one of the best filaments I have tried. It is true that there we found bubbles in some of the spools, but John was nice enough to send extra rolls with no bubbles at no extra cost. <br />
<br />
The packaging became excellent, with borosilicate bags inside the spools and vacuum packed bags inside a cardboard box. I have to say that the white plastic from TSD is simply the best white filament I have tried until now.<br />
-[[User:Rak|Rak]].<br />
|}<br />
<br />
[[Category:Supplies]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Mendel_Einkaufsf%C3%BChrer&diff=143480Mendel Einkaufsführer2015-01-29T14:53:18Z<p>Merlucin: added store Thingibox</p>
<hr />
<div>{{RepRapNavigation (Deutsch)|name=Mendel}}<br />
<br />
RepRap II: Mendel ist Open Source, daher gibt es keinen einzelnen Ort, um die Maschine zu kaufen, sondern viele verschiedene Möglichkeiten. Dieser Wettbewerb ist gewollt, so dass die Preise mit der Zeit sinken. Unten ist eine Liste der Quellen, woher man Mendel-Teile und/oder Kits bekommt.<br />
<br />
Für eine Excel-Tabelle, die eine komplette Liste der Mendel-Teile mit einer Auflistung der Lieferanten enthält, [[Mendel_assembly_data_sheet |siehe hier]].<br />
<br />
'''Anmerkung:''' Es ist nicht nötig, ein Kit zu kaufen, es gibt viele [[:Category:Mendel RepStrap|RepStraps]] zu kaufen oder zu bauen, die leicht mit den Werkzeugen zusammengebaut werden können, die man bereits besitzt.<br />
<br />
==Zu-Verkaufen-Forum==<br />
<br />
Wir haben ein [http://dev.forums.reprap.org/index.php?93 Zu-Verkaufen/Gesucht-Forum] wo sich jeder, der RepRap-Teile verkaufen oder kaufen möchte, eintragen kann. ''Caveat emptor'' - Wir versuchen, Schwindler und Betrüger aus dem Forum fernzuhalten, es ist jedoch weltweit zugänglich. Man sollte niemals Geld versenden, ohne sich darüber im Klaren zu sein, was man tut.<br />
<br />
==Fertig zusammengebaute Mendel-Kits==<br />
<br />
* X400 CE - Fertig zusammengebauter und CE-zertifizierter X400-Drucker, der auf RepRap basiert - siehe [https://shop.germanreprap.com/de germanreprap.com]<br />
<br />
* Prusa i3 - Fertig zusammengebauter Prusa i3 Reprap 3D Drucker - siehe [http://www.reprapuniverse.com ReprapUniverse.com]<br />
<br />
* Es gibt bisher keine Mendel-Kits, sobald es jedoch welche gibt, bitte hier eintragen.<br />
<br />
==Mendel-Teilekits==<br />
===Vollständige Kits===<br />
* [http://reprap.cc Reprap-Austria] - Anbieter eines vollständigen Prusa Mendel , MendelMax und Rostock Kits<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://www.mendel-parts.com/ Mendel-Parts] - Anbieter eines vollständigen Mendel kit -- Elektronik, Kunststoffe (PU), Gewindestangen, Schrauben, Extruder usw. (Niederland/EU)<br />
* [http://www.2printbeta.de/ 2PrintBeta] - Anbieter aller benötigten Teile für Mendel und Prusa -- [Deutschland/EU]<br />
* [http://www.electronic-things.de/shop electronic-things] - Deutscher Anbieter aller benötigten Teile und vollständiger Kits für Mendel, Mendel90 und Prusa -- [Deutschland/EU]<br />
* [http://reprapsource.com/de/prusa_mendel_kit Reprapsource] - Anbieter eines vollständigen Prusa Mendel Kits<br />
* [http://reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von vollständigen Kits für Prusa Mendel i2, MendelMax 1.5 und Prusa i3<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Druck Shop Berlin] - Berliner Anbieter eines Prusa Mendel i3 Kits (Einstein Version) [Deutschland/EU]<br />
<br />
===Elektronik- und Mechanikkits und -teile===<br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller benötigten Komponenten für den Drucker Bau ( Mechanik, Elektronik, Motoren, Zubehör, Filament, Extruder,Hotends und alles weitere )<br />
* [http://geeksbase.com/shop/ GeeksBase] - Anbieter von Teilekits und Platinen. Gedruckte Kunststoffsets(ABS).(Deutschland)<br />
* [[Generation 7 Electronics]] direkt vom Entwickler [mailto:mah@jump-ing.de Traumflug]<br />
* [http://profounddevices.com/ ProfoundDevices] - Anbieter eines vollständigen Teilekits für den [[Mendel Variations/Catalyst]] -- Elektronik, Kunststoffe (PU), Gewindestangen, Schrauben etc. (Oregon/USA)<br />
* [http://makerbot.com/ Makerbot] - Anbieter von fertigen und Bauteil-Kits / Platinenkits für die dritte Generation der RepRap-Elektronik und Extruderteilen. (New York/USA)<br />
* [http://www.bitsfrombytes.com/ Bits from Bytes] - Anbieter von Kunstoffdraht und alternativer Elektronik (kein RepRap Standard)<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://www.reprapsource.com/ RepRap Source] - Anbieter von Kunststoffdraht, Platinen der älteren Generation und mechanischen Teilen.<br />
* [http://www.iprint3d.org/ iPrint3D] - Anbieter der dritten Generation der RepRap-Elektronik<br />
* [https://shop.grrf.de/index.php?main_page= German RepRap Foundation (GRRF)] - Deutscher Anbieter von fertigen Kits für die dritte Generation der RepRap-Elektronik, Extruderteile, Schrittmotoren, Kunststoffe (ABS), Mechanik-Kits und RepStrap-Kits.<br />
* [http://kd85.com/ KD85.com] - Anbieter von RepRap-Teilen und Materialien in Europa.<br />
*[http://www.pololu.com/catalog/product/1182 Pololu ] - Anbieter eines alternativen Schrittmotortreibers, für mehr Informationen Siehe [[Pololu Electronics|Pololu Elektronik]]<br />
** Innerhalb Deutschlands kann man Pololus bei [http://www.lipoly.de/index.php?main_page=product_info&products_id=181885 diesem], [https://shop.grrf.de/pololu-a4983-stepper-motor-driver-carrier-p-297.html diesem] und [http://www.watterott.com/de/Pololu-A4988-Schrittmotortreiber diesem] Shop bestellen.<br />
** Alternativ kann auch ein [[Stepstick]] verwendet werden, welcher in Deutschland [http://www.ebay.de/itm/Stepstick-A4983-stepper-driver-board-RepRap-/300579027699 hier] billiger zu erhalten ist.<br />
* [http://ultimachine.com/ UltiMachine] - Anbieter von Elektronik, Mechanischen Teilen und Druckmaterial.<br />
* [http://www.reprapstores.com/ RepRap Stores] - Mehrere Anbieter und RepRapper, die Kits, Teile und Materialien verkaufen.<br />
* [http://www.2printbeta.de 2PrintBeta] - Anbieter von Kugellager- , Schrauben- , Zahnriemen- und Stangenkits und vielem mehr.<br />
* [http://www.cubic-print.de Cubic Print] Anbieter von Kunststoffteilen, Prusa Hardware Sets, Alu Platten, Kugellager, LM8UU, usw.<br />
* [http://reprapteile.de RepRapteile] - Prusa i3<br />
* [http://www.reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von Kits und Teilen für Prusa Mendel i2, MendelMax 1.5 und Prusa i3 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Lager, Hotends und Zubehör)<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Drucker Shop in Berlin] - 3D Drucker Shop in Berlin mit 3D Drucker Bausätzen und Teile für Prusa Mendel i3, so wie Reparatur, Verleih und Verkauf von neuen und gebrauchten 3D Druckern (z.B. Irapid, Rostock und Mendel i2)<br />
<br />
===Ge''RepRap''te Teilekits ===<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://reprap.cc Reprap-Austria] - Anbieter von Prusa Teilen aus ABS, Mendel Max und alle weiteren Kits auf Anfrage<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Druck Shop Berlin] - Berliner Anbieter von Prusa Teilen aus ABS und PLA. Druck von Ersatzteilen auch direkt vor Ort im Laden möglich.<br />
<br />
==Anbieter für Mendel-Teile==<br />
* [http://reprap.cc Reprap-Austria] - Anbieter von Teilesets für Mendel, Prusa, Mendel Max, Huxley, Rostock ( Kontakt Formular ).<br />
* [http://geeksbase.com/shop/ GeeksBase] bietet Teilesätze für einen Mendel in ABS an.<br />
* [http://fab.senselab.org sense.fab] bietet bis dahin Teilesätze für einen [[LaserCut Mendel]] an.<br />
* [http://www.reprap-fab.org reprap-fab] bietet Teilesätze für einen Mendel, Prusar, Huxley in ABS an.<br />
* [http://www.2printbeta.de 2PrintBeta] bietet Teilesätze für Mendel, Prusa und Huxley in PLA und gegossen in PU an.<br />
* [http://www.cubic-print.de Cubic Print] bietet Teilesätze für Mendel und Prusa in ABS an.<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von ABS Teilen für Mendel, Prusa und Mendel90<br />
* [http://reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von Teilen (ABS/PLA) für Prusa Mendel i2, MendelMax 1.5 und Prusa i3<br />
* [http://thingibox.com ThingiBOX] - Spanischer Anbieter von Teilen für Mendel, Prusa u.a.<br />
===Schrittmotoren===<br />
*[[Suppliers/Stepper Motors|Anbieter/Schrittmotoren]] - Enthält Details um festzustellen, ob ein Motor geeignet ist.<br />
<br />
===Elektronik===<br />
<br />
* [[Generation 7 Electronics]] Leiterplatten und Bauteilzusammenstellungen von [mailto:mah@jump-ing.de Traumflug]<br />
* [http://www.conrad.de/ Conrad Elektronik] - '''(Läden/online)'''<br />
* [http://www.reichelt.de/ Reichelt] - '''(online)'''<br />
* [http://www.digikey.com/ digikey US] - '''(online)'''<br />
* [http://www.digikey.ca/ digikey Canada] - '''Canada (online)'''<br />
* [http://mouser.com Mouser] - '''online'''<br />
* [http://reprapteile.de/elektronik.html?___store=en RepRapteile.de] - '''Europe''' - Ramps 1.4, Arduino, ... <br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller elektronischen Komponenten für Prusa und ähnliche Drucker.<br />
* [http://thingibox.com ThingiBOX] - Spanischer Anbieter von elektronischen Komponenten für 3D-Drucker<br />
<br />
===Mechanik===<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller mechanischen Teile für Prusa, MendelMax, Rostock und ähnliche Drucker.<br />
* [http://www.mcmaster.com/ McMaster-Carr] - '''Versand nur innerhalb der USA(online)''' - Anbieter für alle nicht druckbaren mechanischen Teile für Mendel.<br />
* [http://www.fastenal.com/web/home.ex Fastenal] - '''Kanada und USA (Läden/online)''' - Anbieter für alle nicht druckbaren mechanischen Teile außer den Synchronriemen.<br />
* [http://www.sdp-si.com/web/html/products.htm SDP/SI] - '''Kanada (online)''' - Anbieter für nicht druckbare mechanische Teile inklusive Synchronriemen (es ist nicht bekannt ob alle nicht druckbaren Teile angeboten werden oder nicht).<br />
* [http://www.kugellager-express.de/ Kugellager - Express] - '''Deutschland''' - Deutscher Anbieter für Kugellager<br />
* [http://www.2printbeta.de 2PrintBeta] - '''Deutschland''' - Anbieter für alle nicht druckbaren mechanischen Teile für Mendel.<br />
* [http://reprapteile.de?___store=en RepRapteile]- '''Europe''' - Bearings, Timing Belts, Pulleys<br />
* [http://thingibox.com ThingiBOX] - Spanischer Anbieter von Teilen für Mendel, Prusa u.a.<br />
<br />
==Anbieter von Druckmaterial==<br />
Für Anbieter von ABS/PLA/Etc. siehe [[Printing Material Suppliers|Anbieter von Druckmaterial]]<br />
<br />
==Zu-Verkaufen-Forum==<br />
* RepRap-Teile werden außerdem im [http://forums.reprap.org/list.php?94 RepRap Zu-Verkaufen-Forum] angeboten.<br />
<br />
[[Category:Anbieter]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Mendel_Einkaufsf%C3%BChrer&diff=143342Mendel Einkaufsführer2015-01-26T21:08:35Z<p>Merlucin: Updated missing link</p>
<hr />
<div>{{RepRapNavigation (Deutsch)|name=Mendel}}<br />
<br />
RepRap II: Mendel ist Open Source, daher gibt es keinen einzelnen Ort, um die Maschine zu kaufen, sondern viele verschiedene Möglichkeiten. Dieser Wettbewerb ist gewollt, so dass die Preise mit der Zeit sinken. Unten ist eine Liste der Quellen, woher man Mendel-Teile und/oder Kits bekommt.<br />
<br />
Für eine Excel-Tabelle, die eine komplette Liste der Mendel-Teile mit einer Auflistung der Lieferanten enthält, [[Mendel_assembly_data_sheet |siehe hier]].<br />
<br />
'''Anmerkung:''' Es ist nicht nötig, ein Kit zu kaufen, es gibt viele [[:Category:Mendel RepStrap|RepStraps]] zu kaufen oder zu bauen, die leicht mit den Werkzeugen zusammengebaut werden können, die man bereits besitzt.<br />
<br />
==Zu-Verkaufen-Forum==<br />
<br />
Wir haben ein [http://dev.forums.reprap.org/index.php?93 Zu-Verkaufen/Gesucht-Forum] wo sich jeder, der RepRap-Teile verkaufen oder kaufen möchte, eintragen kann. ''Caveat emptor'' - Wir versuchen, Schwindler und Betrüger aus dem Forum fernzuhalten, es ist jedoch weltweit zugänglich. Man sollte niemals Geld versenden, ohne sich darüber im Klaren zu sein, was man tut.<br />
<br />
==Fertig zusammengebaute Mendel-Kits==<br />
<br />
* X400 CE - Fertig zusammengebauter und CE-zertifizierter X400-Drucker, der auf RepRap basiert - siehe [https://shop.germanreprap.com/de germanreprap.com]<br />
<br />
* Prusa i3 - Fertig zusammengebauter Prusa i3 Reprap 3D Drucker - siehe [http://www.reprapuniverse.com ReprapUniverse.com]<br />
<br />
* Es gibt bisher keine Mendel-Kits, sobald es jedoch welche gibt, bitte hier eintragen.<br />
<br />
==Mendel-Teilekits==<br />
===Vollständige Kits===<br />
* [http://reprap.cc Reprap-Austria] - Anbieter eines vollständigen Prusa Mendel , MendelMax und Rostock Kits<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://www.mendel-parts.com/ Mendel-Parts] - Anbieter eines vollständigen Mendel kit -- Elektronik, Kunststoffe (PU), Gewindestangen, Schrauben, Extruder usw. (Niederland/EU)<br />
* [http://www.2printbeta.de/ 2PrintBeta] - Anbieter aller benötigten Teile für Mendel und Prusa -- [Deutschland/EU]<br />
* [http://www.electronic-things.de/shop electronic-things] - Deutscher Anbieter aller benötigten Teile und vollständiger Kits für Mendel, Mendel90 und Prusa -- [Deutschland/EU]<br />
* [http://reprapsource.com/de/prusa_mendel_kit Reprapsource] - Anbieter eines vollständigen Prusa Mendel Kits<br />
* [http://reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von vollständigen Kits für Prusa Mendel i2, MendelMax 1.5 und Prusa i3<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Druck Shop Berlin] - Berliner Anbieter eines Prusa Mendel i3 Kits (Einstein Version) [Deutschland/EU]<br />
<br />
===Elektronik- und Mechanikkits und -teile===<br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller benötigten Komponenten für den Drucker Bau ( Mechanik, Elektronik, Motoren, Zubehör, Filament, Extruder,Hotends und alles weitere )<br />
* [http://geeksbase.com/shop/ GeeksBase] - Anbieter von Teilekits und Platinen. Gedruckte Kunststoffsets(ABS).(Deutschland)<br />
* [[Generation 7 Electronics]] direkt vom Entwickler [mailto:mah@jump-ing.de Traumflug]<br />
* [http://profounddevices.com/ ProfoundDevices] - Anbieter eines vollständigen Teilekits für den [[Mendel Variations/Catalyst]] -- Elektronik, Kunststoffe (PU), Gewindestangen, Schrauben etc. (Oregon/USA)<br />
* [http://makerbot.com/ Makerbot] - Anbieter von fertigen und Bauteil-Kits / Platinenkits für die dritte Generation der RepRap-Elektronik und Extruderteilen. (New York/USA)<br />
* [http://www.bitsfrombytes.com/ Bits from Bytes] - Anbieter von Kunstoffdraht und alternativer Elektronik (kein RepRap Standard)<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://www.reprapsource.com/ RepRap Source] - Anbieter von Kunststoffdraht, Platinen der älteren Generation und mechanischen Teilen.<br />
* [http://www.iprint3d.org/ iPrint3D] - Anbieter der dritten Generation der RepRap-Elektronik<br />
* [https://shop.grrf.de/index.php?main_page= German RepRap Foundation (GRRF)] - Deutscher Anbieter von fertigen Kits für die dritte Generation der RepRap-Elektronik, Extruderteile, Schrittmotoren, Kunststoffe (ABS), Mechanik-Kits und RepStrap-Kits.<br />
* [http://kd85.com/ KD85.com] - Anbieter von RepRap-Teilen und Materialien in Europa.<br />
*[http://www.pololu.com/catalog/product/1182 Pololu ] - Anbieter eines alternativen Schrittmotortreibers, für mehr Informationen Siehe [[Pololu Electronics|Pololu Elektronik]]<br />
** Innerhalb Deutschlands kann man Pololus bei [http://www.lipoly.de/index.php?main_page=product_info&products_id=181885 diesem], [https://shop.grrf.de/pololu-a4983-stepper-motor-driver-carrier-p-297.html diesem] und [http://www.watterott.com/de/Pololu-A4988-Schrittmotortreiber diesem] Shop bestellen.<br />
** Alternativ kann auch ein [[Stepstick]] verwendet werden, welcher in Deutschland [http://www.ebay.de/itm/Stepstick-A4983-stepper-driver-board-RepRap-/300579027699 hier] billiger zu erhalten ist.<br />
* [http://ultimachine.com/ UltiMachine] - Anbieter von Elektronik, Mechanischen Teilen und Druckmaterial.<br />
* [http://www.reprapstores.com/ RepRap Stores] - Mehrere Anbieter und RepRapper, die Kits, Teile und Materialien verkaufen.<br />
* [http://www.2printbeta.de 2PrintBeta] - Anbieter von Kugellager- , Schrauben- , Zahnriemen- und Stangenkits und vielem mehr.<br />
* [http://www.cubic-print.de Cubic Print] Anbieter von Kunststoffteilen, Prusa Hardware Sets, Alu Platten, Kugellager, LM8UU, usw.<br />
* [http://reprapteile.de RepRapteile] - Prusa i3<br />
* [http://www.reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von Kits und Teilen für Prusa Mendel i2, MendelMax 1.5 und Prusa i3 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Lager, Hotends und Zubehör)<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Drucker Shop in Berlin] - 3D Drucker Shop in Berlin mit 3D Drucker Bausätzen und Teile für Prusa Mendel i3, so wie Reparatur, Verleih und Verkauf von neuen und gebrauchten 3D Druckern (z.B. Irapid, Rostock und Mendel i2)<br />
<br />
===Ge''RepRap''te Teilekits ===<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://reprap.cc Reprap-Austria] - Anbieter von Prusa Teilen aus ABS, Mendel Max und alle weiteren Kits auf Anfrage<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Druck Shop Berlin] - Berliner Anbieter von Prusa Teilen aus ABS und PLA. Druck von Ersatzteilen auch direkt vor Ort im Laden möglich.<br />
<br />
==Anbieter für Mendel-Teile==<br />
* [http://reprap.cc Reprap-Austria] - Anbieter von Teilesets für Mendel, Prusa, Mendel Max, Huxley, Rostock ( Kontakt Formular ).<br />
* [http://geeksbase.com/shop/ GeeksBase] bietet Teilesätze für einen Mendel in ABS an.<br />
* [http://fab.senselab.org sense.fab] bietet bis dahin Teilesätze für einen [[LaserCut Mendel]] an.<br />
* [http://www.reprap-fab.org reprap-fab] bietet Teilesätze für einen Mendel, Prusar, Huxley in ABS an.<br />
* [http://www.2printbeta.de 2PrintBeta] bietet Teilesätze für Mendel, Prusa und Huxley in PLA und gegossen in PU an.<br />
* [http://www.cubic-print.de Cubic Print] bietet Teilesätze für Mendel und Prusa in ABS an.<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von ABS Teilen für Mendel, Prusa und Mendel90<br />
* [http://reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von Teilen (ABS/PLA) für Prusa Mendel i2, MendelMax 1.5 und Prusa i3<br />
* [http://thingibox.com ThingiBOX] - Spanischer Anbieter von Teilen für Mendel, Prusa u.a.<br />
===Schrittmotoren===<br />
*[[Suppliers/Stepper Motors|Anbieter/Schrittmotoren]] - Enthält Details um festzustellen, ob ein Motor geeignet ist.<br />
<br />
===Elektronik===<br />
<br />
* [[Generation 7 Electronics]] Leiterplatten und Bauteilzusammenstellungen von [mailto:mah@jump-ing.de Traumflug]<br />
* [http://www.conrad.de/ Conrad Elektronik] - '''(Läden/online)'''<br />
* [http://www.reichelt.de/ Reichelt] - '''(online)'''<br />
* [http://www.digikey.com/ digikey US] - '''(online)'''<br />
* [http://www.digikey.ca/ digikey Canada] - '''Canada (online)'''<br />
* [http://mouser.com Mouser] - '''online'''<br />
* [http://reprapteile.de/elektronik.html?___store=en RepRapteile.de] - '''Europe''' - Ramps 1.4, Arduino, ... <br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller elektronischen Komponenten für Prusa und ähnliche Drucker.<br />
<br />
===Mechanik===<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller mechanischen Teile für Prusa, MendelMax, Rostock und ähnliche Drucker.<br />
* [http://www.mcmaster.com/ McMaster-Carr] - '''Versand nur innerhalb der USA(online)''' - Anbieter für alle nicht druckbaren mechanischen Teile für Mendel.<br />
* [http://www.fastenal.com/web/home.ex Fastenal] - '''Kanada und USA (Läden/online)''' - Anbieter für alle nicht druckbaren mechanischen Teile außer den Synchronriemen.<br />
* [http://www.sdp-si.com/web/html/products.htm SDP/SI] - '''Kanada (online)''' - Anbieter für nicht druckbare mechanische Teile inklusive Synchronriemen (es ist nicht bekannt ob alle nicht druckbaren Teile angeboten werden oder nicht).<br />
* [http://www.kugellager-express.de/ Kugellager - Express] - '''Deutschland''' - Deutscher Anbieter für Kugellager<br />
* [http://www.2printbeta.de 2PrintBeta] - '''Deutschland''' - Anbieter für alle nicht druckbaren mechanischen Teile für Mendel.<br />
* [http://reprapteile.de?___store=en RepRapteile]- '''Europe''' - Bearings, Timing Belts, Pulleys<br />
<br />
==Anbieter von Druckmaterial==<br />
Für Anbieter von ABS/PLA/Etc. siehe [[Printing Material Suppliers|Anbieter von Druckmaterial]]<br />
<br />
==Zu-Verkaufen-Forum==<br />
* RepRap-Teile werden außerdem im [http://forums.reprap.org/list.php?94 RepRap Zu-Verkaufen-Forum] angeboten.<br />
<br />
[[Category:Anbieter]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Clone_Wars:_Tiendas/es&diff=142873Clone Wars: Tiendas/es2015-01-22T22:31:23Z<p>Merlucin: /* On-line España */</p>
<hr />
<div>{{Languages|Clone_Wars:_Tiendas}} <br />
== Tiendas ==<br />
Sección donde se listan por orden alfabético las tiendas donde es posible encontrar componentes para tu impresora 3d:<br />
=== On-line España ===<br />
<br />
* [http://3despana.com/ '''3DEspana.com'''] (España - Madrid) Tienda online barata de todos los componentes y filamentos para impresoras 3D (Posibilidad de entrega en Madrid Gratuita) Envio 24/48Horas<br />
* [http://3dinvasion.com/ '''3Dinvasion'''] (España - Canarias) Venta de todos los componentes y filamento para impresoras 3D y talleres 3D. Envio 24h/48h a Canarias<br />
* [http://www.3dorobotics.com/tienda/ '''3DoRobotics'''] (España) Todo lo relacionado con la impresión 3D. Distribución de las mejores marcas. Servicio de impresión 3D bajo demanda.<br />
* [http://bcndynamics.com/ '''BCN Dynamics'''] (Barcelona) Tecnologia libre e impresoras 3D. Todos los componentes necesarios para montar impresoras 3D, desde tornillos sueltos, pasando por electrónica Arduino, hasta kits completos. Filamentos, suministros y mejoras.<br />
* [http://shop.createc3d.com '''Createc 3D shop''']: Lab y Makerspace en Granada con tienda física y online donde poder comprar cualquier cosa relacionada con la impresión 3D y tecnología Open Source. Cursos y talleres con formación continua.<br />
* [http://www.clipper3d.es/ '''Clipper3D'''] (España)(León) Todo lo necesario para montar tu Impresora 3D, Desarrollos propios, Cursos, Talleres, Venta de Impresoras (Entrega en León Gratuita) Envio 24/48Horas<br />
* [http://filamentoabs.com/ FilamentoABS] (España). Envíos gratis a Madrid [filamento]<br />
* [http://formate21.es/impresoras-3d/ Formate 21] (España) Venta de todos los componentes para impresoras 3D. Talleres 3D por toda España.<br />
* [http://www.iberobotics.com/shop/index.php?cPath=94 '''IBEROBOTICS Shop'''] Kits completos de calidad superior: Prusa i3 Hephestos y P3Steel PRO. Envío gratis para España y Portugal peninsular. Servicio de montaje opcional.<br />
* [http://ifusionshop.com/index.php iFusionShop] Componentes para impresoras 3D. Servicio de impresión y prototipado en 3D. También puedes solicitar la recogida en mano si eres de Tarragona, llamando al teléfono de la web<br />
* [http://www.igus.es/default.asp Igus] (España) Tienda especializada en rodamientos lineales sin bolas, cadenas porta cables en sistemas plásticas de alto rendimiento y mesas con husillo.<br />
* [http://impresoras3dlowcost.com Impresoras3DLowCost.com] (España)(Andalucía) Tenemos todo lo que necesitas para montar tu [http://impresoras3dlowcost.com impresora 3D] a los mejores precios, con atención personalizada y respuesta en menos de 24 horas.<br />
* [http://www.imprimiendoen3d.es IMPRIMIENDO EN 3D] (España) Tienda online con todo lo necesario para construir tu impresora 3d. Rodamientos, motores, electronica, varillas, filamento.<br />
* [http://www.iniciativas3d.com/ '''Iniciativas3D''' ](España) Tu tienda de impresión 3D en Córdoba. Kits y filamento. Sin costes de envío o recoge tu pedido en nuestra delegación en Córdoba o Málaga.<br />
* [http://www.kitprinter3d.com KITPRINTER3D ] 'Kits de Prusa i3 y P3Steel, ABS y PLA. Tienda física en el centro de Madrid.<br />
* [http://leapto3d.com/ LeapTo3D] (España) - Kits completos con TODO incluido. Recogida gratuita en Madrid. [filamento]<br />
* [http://www.lemonmaker.es/ LemonMaker] (España) Diseño & Impresión 3D. Kits impresoras 3D, workshops, componentes y filamento. Albacete, Madrid y Murcia.<br />
* [http://www.leon-3d.es/ '''LEON3D'''] (España - León) Todo lo necesario para montar tu Impresora 3D, Desarrollos propios, Cursos, Talleres, Venta de Impresoras (Entrega en León Gratuita) Envio 24/48Horas<br />
* [http://shop.menextech.com/index.php MENEXTECH] (España) Todo lo necesario para que construyas tu impresora y componentes informaticos.<br />
* [http://www.moebyus.com/ Moebyus Machines ](España) Entrega en 24h. Kits, marcos de metacrilato, filamento y todos los componentes necesarios para la prusa i3.<br />
* [http://printallthethings.com '''Print All the Things!!!'''] (España)(Galicia) Amplia variedad de colores PLA/ABS del bueno en 24h. También fabrican injectores jhead de gran calidad, y tienen camas calientes mk2b en negro con leds azules.<br />
* [http://www.printeddreams.es '''Printed Dreams'''] (España)(Madrid) Servicio 360° sobre impresión 3D. Kits impresora 3D, ABS/PLA en 18 colores diferentes, FILAFLEX y productos REPRAPBCN. info@printeddreams.es<br />
* [http://printhatshit.com PRINTHATSHIT - Easy 3D Printing -] (España) Tienda online y física en Barcelona. Envío 24 horas y recogida en tienda.<br />
* [http://www.plabs3d.com PLABS 3D] (España) Disponen de muchos filamentos: PLA, ABS, HIPS, Nylon, Laywood, Laybrick, PVA, TPE, PS, Poikilothermal, Conductivo, Glow in the dark, etc...<br />
* [http://www.rationalstock.es/ Rational Stock] (España) Ferretería online. Variedad y buenos precios para tornillería. Permite comprar por unidades. Envío económico en 24-48 horas.<br />
* [http://shop.reclone3d.com/ Reclone3D] (España) Tienda de impresoras 3D.<br />
* [http://www.repparts3d.com/ '''RepParts 3D'''] (España) ABS, PLA, Conductor, Termocrómico, LayWood, LayBrick, Glow in the Dark, Nylon, HIPS. Con la mas amplia gama de colores<br />
* [http://www.staticboards.es/productos/ '''StaticBoards'''] (España) Fabrica Electrónica RAMPS 1.4SB Premium y Camas Calientes MK2B en Galicia.<br />
* [http://store.thingibox.com/ '''ThingiBOX'''] (España)(Barcelona) Componentes y filamentos para impresoras 3D y otros proyectos oscuros. Servicio de corte con laser de CO2.<br />
* [http://wi3dprint.com/ '''wi3Dprint'''] (España) Venta impresoras 3D, talleres, componentes y filamentos. Servicio de impresión<br />
<br />
=== On-line ===<br />
Europa:<br />
* [http://www.mendel-parts.com/ Mendel parts] (Holanda)<br />
* [http://www.xyzprinters.com/ http://www.xyzprinters.com/] (Holanda)<br />
* [http://shop.arcol.hu/ arcol.hu] (Hungría) <br />
* [https://shop.grrf.de/ German RepRap fundation] (Alemania)<br />
* [http://reprapsource.com/ reprapsource.com]<br />
* [http://reprapworld.com/ Reprap world] (Holanda) [filamento]<br />
* [https://0xfb.com/shop.html Future Bits] La tienda de Kliment! (Alemania)<br />
* [http://www.hotends.com/ hotends]<br />
* [http://www.orbi-tech.de/index_english.htm Orbi-tech]. Plástico (Alemania)<br />
* [http://reprap-3d-printer.com/ Reprap-3D-printer] (Francia)<br />
<br />
EEUU / América (ojo aduanas)<br />
* [http://www.makergear.com/ Makergear] (EEUU)<br />
* [http://www.lulzbot.com/en/ Lulzbot] (EEUU)<br />
* [http://gala-automation.com/ Gala automation] (EEUU)<br />
* [http://techpaladin.com/ techpaladin] (EEUU)<br />
* [http://www.centralreprap.com/prestashop/ CentralReprap]<br />
* [http://ultimachine.com/ Ultimachine] (EEUU)<br />
* [http://www.makermex.com/ MakerMex] (México)<br />
* [http://www.3dm.mx/ 3DM] (México) Impresoras 3D RepRap al Mejor Precio de México. Entrega Inmediata, consumibles y componentes.<br />
<br />
Otros <br />
* [http://www.3dacessorieshub.com/ 3D Acessories Hub ].Una ventanilla única para todos los componentes de RepRap y las impresoras 3D<br />
* [http://www.goodluckbuy.com/ http://www.goodluckbuy.com/]. Tienda en china donde venden motores, varillas roscadas...<br />
* [http://www.futurlec.com/ Futurlec] Electrónica en general<br />
* [http://www.taydaelectronics.com/ Tayda Electronics] Electrónica en general<br />
* [http://www.dealextreme.com/ Dealextreme] Tienda china con prácticamente cualquier cosa. (contrasta precios antes de comprar)<br />
* [http://www.bitsbox.co.uk/ BitsBox] Componentes electrónicos, algunos especialmente baratos. Envía por ~3€<br />
* [http://www.emakershop.com/ eMAKERshop] Tienda online que vende productos de varios vendedores externos, como un portal de venta.<br />
* [http://www.zappautomation.co.uk/index.php?language=ES Zappautomation] Tienda con todo tipo de productos para CNCs (UK)<br />
* [http://makemendel.com/ Makemendel]<br />
* [http://www.ebay.com/itm/1pc-200mm-X-100ft-High-Temperature-Resistant-Kapton-Tape-/170864710486?ssPageName=ADME:L:OU:ES:3160 Kapton en eBay]: Cinta kapton de 20cm de ancho<br />
* [http://www.reprap.cc/ Reprap Austria] Tienda de todo tipo de material para Reprap tambien en ebay: [http://www.ebay.es/sch/reprapper/m.html?_nkw=&_armrs=1&_from=&_ipg=&_trksid=p3686 reprapper]<br />
<br />
=== Físicas ===<br />
* [[Clone_wars:_Tiendas_en_Andalucia|Andalucía]]<br />
* [[Clone_wars:_Tiendas_en_asturias|Asturias]]<br />
* [[Clone_wars:_Tiendas_en_barcelona|Barcelona]]<br />
* [[Clone_wars:_Tiendas_en_Cantabria|Cantabria]]<br />
* [[Clone_wars:_Tiendas_en_castellon|Castellón]]<br />
* [[Clone_wars:_Tiendas_en_galicia|Galicia]]<br />
* [[Clone_wars:_Tiendas_en_leon|León]]<br />
* [[Clone_wars:_Tiendas_en_madrid|Madrid]]<br />
* [[Clone_wars:_Tiendas_en_navarra|Navarra]]<br />
* [[Clone_wars:_Tiendas_en_Euskadi|Pais Vasco]]<br />
* [[Clone_wars:_Tiendas_en_valencia|Valencia]]<br />
* [[Clone_wars:_Tiendas_en_zaragoza|Zaragoza]]<br />
[http://goo.gl/maps/Md32Y Mapa] de tiendas y talleres<br />
<br />
=== Lista negra de tiendas ===<br />
Tiendas con las que hemos tenido malas experiencias:<br />
* [http://myworld.ebay.es/drumas09/ drumas09] (UK). Este vendedor no envía los pedidos. Pedro tuvo un problema con este vendedor.<br />
<br />
== Servicios de Corte ==<br />
<br />
'''Cortenfrio'''<br />
*Empresa de corte en frio ubicada en Zaragoza.<br />
*[http://cortenfrio.com/index.htm Cortenfrio]<br />
<br />
'''Laserebro'''<br />
*Son un grupo de empresas con muchas sedes, tienes una cerca de casa seguro :D mira en el mapa de localizacion, en su web, en el apartado: Grupo Láser Ebro.<br />
*[http://www.laserebro.com/frame1.htm Laserebro]<br />
<br />
'''Naivan'''<br />
*Empresa de corte por Laser y otros servicios en Vitoria.<br />
*[http://www.naivan.com/ Naivan]<br />
*Email para enviar los planos de corte: naivan@naivan.com (enviar en dxf o pdf acotado)<br />
*Teléfono:945 259 857<br />
<br />
'''HJL'''<br />
*Empresa de corte por Laser y otros servicios en Murcia.<br />
*[http://www.hjl.es/ HJL]<br />
*Teléfono:968 802 044<br />
<br />
'''ThingiBOX'''<br />
*Corte por Laser en Viladecans (Barcelona).<br />
*[http://www.thingibox.com/ ThingiBOX]<br />
*Teléfono: 93 590 39 39<br />
<br />
{| class="wikitable"<br />
|-<br />
|<br />
[[File:Clone-Wars-logo.png|border|100px|link=Proyecto Clone Wars]]<br />
| [[Proyecto Clone Wars]]<br />
|}<br />
<br />
[[Category:Clone wars/es]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Clone_Wars:_Tiendas/es&diff=142872Clone Wars: Tiendas/es2015-01-22T22:30:43Z<p>Merlucin: Eliminados formatos publicitarios</p>
<hr />
<div>{{Languages|Clone_Wars:_Tiendas}} <br />
== Tiendas ==<br />
Sección donde se listan por orden alfabético las tiendas donde es posible encontrar componentes para tu impresora 3d:<br />
=== On-line España ===<br />
<br />
* [http://3despana.com/ '''3DEspana.com'''] (España - Madrid) Tienda online barata de todos los componentes y filamentos para impresoras 3D (Posibilidad de entrega en Madrid Gratuita) Envio 24/48Horas<br />
* [http://3dinvasion.com/ '''3Dinvasion'''] (España - Canarias) Venta de todos los componentes y filamento para impresoras 3D y talleres 3D. Envio 24h/48h a Canarias<br />
* [http://www.3dorobotics.com/tienda/ '''3DoRobotics'''] (España) Todo lo relacionado con la impresión 3D. Distribución de las mejores marcas. Servicio de impresión 3D bajo demanda.<br />
* [http://bcndynamics.com/ '''BCN Dynamics'''] (Barcelona) Tecnologia libre e impresoras 3D. Todos los componentes necesarios para montar impresoras 3D, desde tornillos sueltos, pasando por electrónica Arduino, hasta kits completos. Filamentos, suministros y mejoras.<br />
* [http://shop.createc3d.com '''Createc 3D shop''']: Lab y Makerspace en Granada con tienda física y online donde poder comprar cualquier cosa relacionada con la impresión 3D y tecnología Open Source. Cursos y talleres con formación continua.<br />
* [http://www.clipper3d.es/ '''Clipper3D'''] (España)(León) Todo lo necesario para montar tu Impresora 3D, Desarrollos propios, Cursos, Talleres, Venta de Impresoras (Entrega en León Gratuita) Envio 24/48Horas<br />
* [http://filamentoabs.com/ FilamentoABS] (España). Envíos gratis a Madrid [filamento]<br />
* [http://formate21.es/impresoras-3d/ Formate 21] (España) Venta de todos los componentes para impresoras 3D. Talleres 3D por toda España.<br />
* [http://www.iberobotics.com/shop/index.php?cPath=94 '''IBEROBOTICS Shop'''] Kits completos de calidad superior: Prusa i3 Hephestos y P3Steel PRO. Envío gratis para España y Portugal peninsular. Servicio de montaje opcional.<br />
* [http://ifusionshop.com/index.php iFusionShop] Componentes para impresoras 3D. Servicio de impresión y prototipado en 3D. También puedes solicitar la recogida en mano si eres de Tarragona, llamando al teléfono de la web<br />
* [http://www.igus.es/default.asp Igus] (España) Tienda especializada en rodamientos lineales sin bolas, cadenas porta cables en sistemas plásticas de alto rendimiento y mesas con husillo.<br />
* [http://impresoras3dlowcost.com Impresoras3DLowCost.com] (España)(Andalucía) Tenemos todo lo que necesitas para montar tu [http://impresoras3dlowcost.com impresora 3D] a los mejores precios, con atención personalizada y respuesta en menos de 24 horas.<br />
* [http://www.imprimiendoen3d.es IMPRIMIENDO EN 3D] (España) Tienda online con todo lo necesario para construir tu impresora 3d. Rodamientos, motores, electronica, varillas, filamento.<br />
* [http://www.iniciativas3d.com/ '''Iniciativas3D''' ](España) Tu tienda de impresión 3D en Córdoba. Kits y filamento. Sin costes de envío o recoge tu pedido en nuestra delegación en Córdoba o Málaga.<br />
* [http://www.kitprinter3d.com KITPRINTER3D ] 'Kits de Prusa i3 y P3Steel, ABS y PLA. Tienda física en el centro de Madrid.<br />
* [http://leapto3d.com/ LeapTo3D] (España) - Kits completos con TODO incluido. Recogida gratuita en Madrid. [filamento]<br />
* [http://www.lemonmaker.es/ LemonMaker] (España) Diseño & Impresión 3D. Kits impresoras 3D, workshops, componentes y filamento. Albacete, Madrid y Murcia.<br />
* [http://www.leon-3d.es/ '''LEON3D'''] (España - León) Todo lo necesario para montar tu Impresora 3D, Desarrollos propios, Cursos, Talleres, Venta de Impresoras (Entrega en León Gratuita) Envio 24/48Horas<br />
* [http://shop.menextech.com/index.php MENEXTECH] (España) Todo lo necesario para que construyas tu impresora y componentes informaticos.<br />
* [http://www.moebyus.com/ Moebyus Machines ](España) Entrega en 24h. Kits, marcos de metacrilato, filamento y todos los componentes necesarios para la prusa i3.<br />
* [http://printallthethings.com '''Print All the Things!!!'''] (España)(Galicia) Amplia variedad de colores PLA/ABS del bueno en 24h. También fabrican injectores jhead de gran calidad, y tienen camas calientes mk2b en negro con leds azules.<br />
* [http://www.printeddreams.es '''Printed Dreams'''] (España)(Madrid) Servicio 360° sobre impresión 3D. Kits impresora 3D, ABS/PLA en 18 colores diferentes, FILAFLEX y productos REPRAPBCN. info@printeddreams.es<br />
* [http://printhatshit.com PRINTHATSHIT - Easy 3D Printing -] (España) Tienda online y física en Barcelona. Envío 24 horas y recogida en tienda.<br />
* [http://www.plabs3d.com PLABS 3D] (España) Disponen de muchos filamentos: PLA, ABS, HIPS, Nylon, Laywood, Laybrick, PVA, TPE, PS, Poikilothermal, Conductivo, Glow in the dark, etc...<br />
* [http://www.rationalstock.es/ Rational Stock] (España) Ferretería online. Variedad y buenos precios para tornillería. Permite comprar por unidades. Envío económico en 24-48 horas.<br />
* [http://shop.reclone3d.com/ Reclone3D] (España) Tienda de impresoras 3D.<br />
* [http://www.repparts3d.com/ '''RepParts 3D'''] (España) ABS, PLA, Conductor, Termocrómico, LayWood, LayBrick, Glow in the Dark, Nylon, HIPS. Con la mas amplia gama de colores<br />
* [http://www.staticboards.es/productos/ '''StaticBoards'''] (España) Fabrica Electrónica RAMPS 1.4SB Premium y Camas Calientes MK2B en Galicia.<br />
* [http://www.thingibox.com/ '''ThingiBOX'''] (España) Componentes y filamentos para impresoras 3D y otros proyectos oscuros. Servicio de corte con laser de CO2.<br />
* [http://wi3dprint.com/ '''wi3Dprint'''] (España) Venta impresoras 3D, talleres, componentes y filamentos. Servicio de impresión<br />
<br />
=== On-line ===<br />
Europa:<br />
* [http://www.mendel-parts.com/ Mendel parts] (Holanda)<br />
* [http://www.xyzprinters.com/ http://www.xyzprinters.com/] (Holanda)<br />
* [http://shop.arcol.hu/ arcol.hu] (Hungría) <br />
* [https://shop.grrf.de/ German RepRap fundation] (Alemania)<br />
* [http://reprapsource.com/ reprapsource.com]<br />
* [http://reprapworld.com/ Reprap world] (Holanda) [filamento]<br />
* [https://0xfb.com/shop.html Future Bits] La tienda de Kliment! (Alemania)<br />
* [http://www.hotends.com/ hotends]<br />
* [http://www.orbi-tech.de/index_english.htm Orbi-tech]. Plástico (Alemania)<br />
* [http://reprap-3d-printer.com/ Reprap-3D-printer] (Francia)<br />
<br />
EEUU / América (ojo aduanas)<br />
* [http://www.makergear.com/ Makergear] (EEUU)<br />
* [http://www.lulzbot.com/en/ Lulzbot] (EEUU)<br />
* [http://gala-automation.com/ Gala automation] (EEUU)<br />
* [http://techpaladin.com/ techpaladin] (EEUU)<br />
* [http://www.centralreprap.com/prestashop/ CentralReprap]<br />
* [http://ultimachine.com/ Ultimachine] (EEUU)<br />
* [http://www.makermex.com/ MakerMex] (México)<br />
* [http://www.3dm.mx/ 3DM] (México) Impresoras 3D RepRap al Mejor Precio de México. Entrega Inmediata, consumibles y componentes.<br />
<br />
Otros <br />
* [http://www.3dacessorieshub.com/ 3D Acessories Hub ].Una ventanilla única para todos los componentes de RepRap y las impresoras 3D<br />
* [http://www.goodluckbuy.com/ http://www.goodluckbuy.com/]. Tienda en china donde venden motores, varillas roscadas...<br />
* [http://www.futurlec.com/ Futurlec] Electrónica en general<br />
* [http://www.taydaelectronics.com/ Tayda Electronics] Electrónica en general<br />
* [http://www.dealextreme.com/ Dealextreme] Tienda china con prácticamente cualquier cosa. (contrasta precios antes de comprar)<br />
* [http://www.bitsbox.co.uk/ BitsBox] Componentes electrónicos, algunos especialmente baratos. Envía por ~3€<br />
* [http://www.emakershop.com/ eMAKERshop] Tienda online que vende productos de varios vendedores externos, como un portal de venta.<br />
* [http://www.zappautomation.co.uk/index.php?language=ES Zappautomation] Tienda con todo tipo de productos para CNCs (UK)<br />
* [http://makemendel.com/ Makemendel]<br />
* [http://www.ebay.com/itm/1pc-200mm-X-100ft-High-Temperature-Resistant-Kapton-Tape-/170864710486?ssPageName=ADME:L:OU:ES:3160 Kapton en eBay]: Cinta kapton de 20cm de ancho<br />
* [http://www.reprap.cc/ Reprap Austria] Tienda de todo tipo de material para Reprap tambien en ebay: [http://www.ebay.es/sch/reprapper/m.html?_nkw=&_armrs=1&_from=&_ipg=&_trksid=p3686 reprapper]<br />
<br />
=== Físicas ===<br />
* [[Clone_wars:_Tiendas_en_Andalucia|Andalucía]]<br />
* [[Clone_wars:_Tiendas_en_asturias|Asturias]]<br />
* [[Clone_wars:_Tiendas_en_barcelona|Barcelona]]<br />
* [[Clone_wars:_Tiendas_en_Cantabria|Cantabria]]<br />
* [[Clone_wars:_Tiendas_en_castellon|Castellón]]<br />
* [[Clone_wars:_Tiendas_en_galicia|Galicia]]<br />
* [[Clone_wars:_Tiendas_en_leon|León]]<br />
* [[Clone_wars:_Tiendas_en_madrid|Madrid]]<br />
* [[Clone_wars:_Tiendas_en_navarra|Navarra]]<br />
* [[Clone_wars:_Tiendas_en_Euskadi|Pais Vasco]]<br />
* [[Clone_wars:_Tiendas_en_valencia|Valencia]]<br />
* [[Clone_wars:_Tiendas_en_zaragoza|Zaragoza]]<br />
[http://goo.gl/maps/Md32Y Mapa] de tiendas y talleres<br />
<br />
=== Lista negra de tiendas ===<br />
Tiendas con las que hemos tenido malas experiencias:<br />
* [http://myworld.ebay.es/drumas09/ drumas09] (UK). Este vendedor no envía los pedidos. Pedro tuvo un problema con este vendedor.<br />
<br />
== Servicios de Corte ==<br />
<br />
'''Cortenfrio'''<br />
*Empresa de corte en frio ubicada en Zaragoza.<br />
*[http://cortenfrio.com/index.htm Cortenfrio]<br />
<br />
'''Laserebro'''<br />
*Son un grupo de empresas con muchas sedes, tienes una cerca de casa seguro :D mira en el mapa de localizacion, en su web, en el apartado: Grupo Láser Ebro.<br />
*[http://www.laserebro.com/frame1.htm Laserebro]<br />
<br />
'''Naivan'''<br />
*Empresa de corte por Laser y otros servicios en Vitoria.<br />
*[http://www.naivan.com/ Naivan]<br />
*Email para enviar los planos de corte: naivan@naivan.com (enviar en dxf o pdf acotado)<br />
*Teléfono:945 259 857<br />
<br />
'''HJL'''<br />
*Empresa de corte por Laser y otros servicios en Murcia.<br />
*[http://www.hjl.es/ HJL]<br />
*Teléfono:968 802 044<br />
<br />
'''ThingiBOX'''<br />
*Corte por Laser en Viladecans (Barcelona).<br />
*[http://www.thingibox.com/ ThingiBOX]<br />
*Teléfono: 93 590 39 39<br />
<br />
{| class="wikitable"<br />
|-<br />
|<br />
[[File:Clone-Wars-logo.png|border|100px|link=Proyecto Clone Wars]]<br />
| [[Proyecto Clone Wars]]<br />
|}<br />
<br />
[[Category:Clone wars/es]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Mendel_Einkaufsf%C3%BChrer&diff=141913Mendel Einkaufsführer2015-01-16T14:33:21Z<p>Merlucin: /* Anbieter für Mendel-Teile */</p>
<hr />
<div>{{RepRapNavigation (Deutsch)|name=Mendel}}<br />
<br />
RepRap II: Mendel ist Open Source, daher gibt es keinen einzelnen Ort, um die Maschine zu kaufen, sondern viele verschiedene Möglichkeiten. Dieser Wettbewerb ist gewollt, so dass die Preise mit der Zeit sinken. Unten ist eine Liste der Quellen, woher man Mendel-Teile und/oder Kits bekommt.<br />
<br />
Für eine Excel-Tabelle, die eine komplette Liste der Mendel-Teile mit einer Auflistung der Lieferanten enthält, [[Mendel_assembly_data_sheet |siehe hier]].<br />
<br />
'''Anmerkung:''' Es ist nicht nötig, ein Kit zu kaufen, es gibt viele [[:Category:Mendel RepStrap|RepStraps]] zu kaufen oder zu bauen, die leicht mit den Werkzeugen zusammengebaut werden können, die man bereits besitzt.<br />
<br />
==Zu-Verkaufen-Forum==<br />
<br />
Wir haben ein [http://dev.forums.reprap.org/index.php?93 Zu-Verkaufen/Gesucht-Forum] wo sich jeder, der RepRap-Teile verkaufen oder kaufen möchte, eintragen kann. ''Caveat emptor'' - Wir versuchen, Schwindler und Betrüger aus dem Forum fernzuhalten, es ist jedoch weltweit zugänglich. Man sollte niemals Geld versenden, ohne sich darüber im Klaren zu sein, was man tut.<br />
<br />
==Fertig zusammengebaute Mendel-Kits==<br />
<br />
* X400 CE - Fertig zusammengebauter und CE-zertifizierter X400-Drucker, der auf RepRap basiert - siehe [https://shop.germanreprap.com/de germanreprap.com]<br />
<br />
* Prusa i3 - Fertig zusammengebauter Prusa i3 Reprap 3D Drucker - siehe [http://www.reprapuniverse.com ReprapUniverse.com]<br />
<br />
* Es gibt bisher keine Mendel-Kits, sobald es jedoch welche gibt, bitte hier eintragen.<br />
<br />
==Mendel-Teilekits==<br />
===Vollständige Kits===<br />
* [http://reprap.cc Reprap-Austria] - Anbieter eines vollständigen Prusa Mendel , MendelMax und Rostock Kits<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://www.mendel-parts.com/ Mendel-Parts] - Anbieter eines vollständigen Mendel kit -- Elektronik, Kunststoffe (PU), Gewindestangen, Schrauben, Extruder usw. (Niederland/EU)<br />
* [http://www.2printbeta.de/ 2PrintBeta] - Anbieter aller benötigten Teile für Mendel und Prusa -- [Deutschland/EU]<br />
* [http://www.electronic-things.de/shop electronic-things] - Deutscher Anbieter aller benötigten Teile und vollständiger Kits für Mendel, Mendel90 und Prusa -- [Deutschland/EU]<br />
* [http://reprapsource.com/de/prusa_mendel_kit Reprapsource] - Anbieter eines vollständigen Prusa Mendel Kits<br />
* [http://reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von vollständigen Kits für Prusa Mendel i2, MendelMax 1.5 und Prusa i3<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Druck Shop Berlin] - Berliner Anbieter eines Prusa Mendel i3 Kits (Einstein Version) [Deutschland/EU]<br />
<br />
===Elektronik- und Mechanikkits und -teile===<br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller benötigten Komponenten für den Drucker Bau ( Mechanik, Elektronik, Motoren, Zubehör, Filament, Extruder,Hotends und alles weitere )<br />
* [http://geeksbase.com/shop/ GeeksBase] - Anbieter von Teilekits und Platinen. Gedruckte Kunststoffsets(ABS).(Deutschland)<br />
* [[Generation 7 Electronics]] direkt vom Entwickler [mailto:mah@jump-ing.de Traumflug]<br />
* [http://profounddevices.com/ ProfoundDevices] - Anbieter eines vollständigen Teilekits für den [[Mendel Variations/Catalyst]] -- Elektronik, Kunststoffe (PU), Gewindestangen, Schrauben etc. (Oregon/USA)<br />
* [http://makerbot.com/ Makerbot] - Anbieter von fertigen und Bauteil-Kits / Platinenkits für die dritte Generation der RepRap-Elektronik und Extruderteilen. (New York/USA)<br />
* [http://www.bitsfrombytes.com/ Bits from Bytes] - Anbieter von Kunstoffdraht und alternativer Elektronik (kein RepRap Standard)<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://www.reprapsource.com/ RepRap Source] - Anbieter von Kunststoffdraht, Platinen der älteren Generation und mechanischen Teilen.<br />
* [http://www.iprint3d.org/ iPrint3D] - Anbieter der dritten Generation der RepRap-Elektronik<br />
* [https://shop.grrf.de/index.php?main_page= German RepRap Foundation (GRRF)] - Deutscher Anbieter von fertigen Kits für die dritte Generation der RepRap-Elektronik, Extruderteile, Schrittmotoren, Kunststoffe (ABS), Mechanik-Kits und RepStrap-Kits.<br />
* [http://kd85.com/ KD85.com] - Anbieter von RepRap-Teilen und Materialien in Europa.<br />
*[http://www.pololu.com/catalog/product/1182 Pololu ] - Anbieter eines alternativen Schrittmotortreibers, für mehr Informationen Siehe [[Pololu Electronics|Pololu Elektronik]]<br />
** Innerhalb Deutschlands kann man Pololus bei [http://www.lipoly.de/index.php?main_page=product_info&products_id=181885 diesem], [https://shop.grrf.de/pololu-a4983-stepper-motor-driver-carrier-p-297.html diesem] und [http://www.watterott.com/de/Pololu-A4988-Schrittmotortreiber diesem] Shop bestellen.<br />
** Alternativ kann auch ein [[Stepstick]] verwendet werden, welcher in Deutschland [http://www.ebay.de/itm/Stepstick-A4983-stepper-driver-board-RepRap-/300579027699 hier] billiger zu erhalten ist.<br />
* [http://ultimachine.com/ UltiMachine] - Anbieter von Elektronik, Mechanischen Teilen und Druckmaterial.<br />
* [http://www.reprapstores.com/ RepRap Stores] - Mehrere Anbieter und RepRapper, die Kits, Teile und Materialien verkaufen.<br />
* [http://www.2printbeta.de 2PrintBeta] - Anbieter von Kugellager- , Schrauben- , Zahnriemen- und Stangenkits und vielem mehr.<br />
* [http://www.cubic-print.de Cubic Print] Anbieter von Kunststoffteilen, Prusa Hardware Sets, Alu Platten, Kugellager, LM8UU, usw.<br />
* [http://reprapteile.de RepRapteile] - Prusa i3<br />
* [http://www.reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von Kits und Teilen für Prusa Mendel i2, MendelMax 1.5 und Prusa i3 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Lager, Hotends und Zubehör)<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Drucker Shop in Berlin] - 3D Drucker Shop in Berlin mit 3D Drucker Bausätzen und Teile für Prusa Mendel i3, so wie Reparatur, Verleih und Verkauf von neuen und gebrauchten 3D Druckern (z.B. Irapid, Rostock und Mendel i2)<br />
<br />
===Ge''RepRap''te Teilekits ===<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://reprap.cc Reprap-Austria] - Anbieter von Prusa Teilen aus ABS, Mendel Max und alle weiteren Kits auf Anfrage<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Druck Shop Berlin] - Berliner Anbieter von Prusa Teilen aus ABS und PLA. Druck von Ersatzteilen auch direkt vor Ort im Laden möglich.<br />
<br />
==Anbieter für Mendel-Teile==<br />
* [http://reprap.cc Reprap-Austria] - Anbieter von Teilesets für Mendel, Prusa, Mendel Max, Huxley, Rostock ( Kontakt Formular ).<br />
* [http://geeksbase.com/shop/ GeeksBase] bietet Teilesätze für einen Mendel in ABS an.<br />
* [http://fab.senselab.org sense.fab] bietet bis dahin Teilesätze für einen [[LaserCut Mendel]] an.<br />
* [http://www.reprap-fab.org reprap-fab] bietet Teilesätze für einen Mendel, Prusar, Huxley in ABS an.<br />
* [http://www.2printbeta.de 2PrintBeta] bietet Teilesätze für Mendel, Prusa und Huxley in PLA und gegossen in PU an.<br />
* [http://www.cubic-print.de Cubic Print] bietet Teilesätze für Mendel und Prusa in ABS an.<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von ABS Teilen für Mendel, Prusa und Mendel90<br />
* [http://reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von Teilen (ABS/PLA) für Prusa Mendel i2, MendelMax 1.5 und Prusa i3<br />
* [http://thingibox.com] - Spanischer Anbieter von Teilen für Mendel, Prusa u.a.<br />
===Schrittmotoren===<br />
*[[Suppliers/Stepper Motors|Anbieter/Schrittmotoren]] - Enthält Details um festzustellen, ob ein Motor geeignet ist.<br />
<br />
===Elektronik===<br />
<br />
* [[Generation 7 Electronics]] Leiterplatten und Bauteilzusammenstellungen von [mailto:mah@jump-ing.de Traumflug]<br />
* [http://www.conrad.de/ Conrad Elektronik] - '''(Läden/online)'''<br />
* [http://www.reichelt.de/ Reichelt] - '''(online)'''<br />
* [http://www.digikey.com/ digikey US] - '''(online)'''<br />
* [http://www.digikey.ca/ digikey Canada] - '''Canada (online)'''<br />
* [http://mouser.com Mouser] - '''online'''<br />
* [http://reprapteile.de/elektronik.html?___store=en RepRapteile.de] - '''Europe''' - Ramps 1.4, Arduino, ... <br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller elektronischen Komponenten für Prusa und ähnliche Drucker.<br />
<br />
===Mechanik===<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller mechanischen Teile für Prusa, MendelMax, Rostock und ähnliche Drucker.<br />
* [http://www.mcmaster.com/ McMaster-Carr] - '''Versand nur innerhalb der USA(online)''' - Anbieter für alle nicht druckbaren mechanischen Teile für Mendel.<br />
* [http://www.fastenal.com/web/home.ex Fastenal] - '''Kanada und USA (Läden/online)''' - Anbieter für alle nicht druckbaren mechanischen Teile außer den Synchronriemen.<br />
* [http://www.sdp-si.com/web/html/products.htm SDP/SI] - '''Kanada (online)''' - Anbieter für nicht druckbare mechanische Teile inklusive Synchronriemen (es ist nicht bekannt ob alle nicht druckbaren Teile angeboten werden oder nicht).<br />
* [http://www.kugellager-express.de/ Kugellager - Express] - '''Deutschland''' - Deutscher Anbieter für Kugellager<br />
* [http://www.2printbeta.de 2PrintBeta] - '''Deutschland''' - Anbieter für alle nicht druckbaren mechanischen Teile für Mendel.<br />
* [http://reprapteile.de?___store=en RepRapteile]- '''Europe''' - Bearings, Timing Belts, Pulleys<br />
<br />
==Anbieter von Druckmaterial==<br />
Für Anbieter von ABS/PLA/Etc. siehe [[Printing Material Suppliers|Anbieter von Druckmaterial]]<br />
<br />
==Zu-Verkaufen-Forum==<br />
* RepRap-Teile werden außerdem im [http://forums.reprap.org/list.php?94 RepRap Zu-Verkaufen-Forum] angeboten.<br />
<br />
[[Category:Anbieter]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Mendel_Einkaufsf%C3%BChrer&diff=141912Mendel Einkaufsführer2015-01-16T14:31:48Z<p>Merlucin: /* GeRepRapte Teilekits */</p>
<hr />
<div>{{RepRapNavigation (Deutsch)|name=Mendel}}<br />
<br />
RepRap II: Mendel ist Open Source, daher gibt es keinen einzelnen Ort, um die Maschine zu kaufen, sondern viele verschiedene Möglichkeiten. Dieser Wettbewerb ist gewollt, so dass die Preise mit der Zeit sinken. Unten ist eine Liste der Quellen, woher man Mendel-Teile und/oder Kits bekommt.<br />
<br />
Für eine Excel-Tabelle, die eine komplette Liste der Mendel-Teile mit einer Auflistung der Lieferanten enthält, [[Mendel_assembly_data_sheet |siehe hier]].<br />
<br />
'''Anmerkung:''' Es ist nicht nötig, ein Kit zu kaufen, es gibt viele [[:Category:Mendel RepStrap|RepStraps]] zu kaufen oder zu bauen, die leicht mit den Werkzeugen zusammengebaut werden können, die man bereits besitzt.<br />
<br />
==Zu-Verkaufen-Forum==<br />
<br />
Wir haben ein [http://dev.forums.reprap.org/index.php?93 Zu-Verkaufen/Gesucht-Forum] wo sich jeder, der RepRap-Teile verkaufen oder kaufen möchte, eintragen kann. ''Caveat emptor'' - Wir versuchen, Schwindler und Betrüger aus dem Forum fernzuhalten, es ist jedoch weltweit zugänglich. Man sollte niemals Geld versenden, ohne sich darüber im Klaren zu sein, was man tut.<br />
<br />
==Fertig zusammengebaute Mendel-Kits==<br />
<br />
* X400 CE - Fertig zusammengebauter und CE-zertifizierter X400-Drucker, der auf RepRap basiert - siehe [https://shop.germanreprap.com/de germanreprap.com]<br />
<br />
* Prusa i3 - Fertig zusammengebauter Prusa i3 Reprap 3D Drucker - siehe [http://www.reprapuniverse.com ReprapUniverse.com]<br />
<br />
* Es gibt bisher keine Mendel-Kits, sobald es jedoch welche gibt, bitte hier eintragen.<br />
<br />
==Mendel-Teilekits==<br />
===Vollständige Kits===<br />
* [http://reprap.cc Reprap-Austria] - Anbieter eines vollständigen Prusa Mendel , MendelMax und Rostock Kits<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://www.mendel-parts.com/ Mendel-Parts] - Anbieter eines vollständigen Mendel kit -- Elektronik, Kunststoffe (PU), Gewindestangen, Schrauben, Extruder usw. (Niederland/EU)<br />
* [http://www.2printbeta.de/ 2PrintBeta] - Anbieter aller benötigten Teile für Mendel und Prusa -- [Deutschland/EU]<br />
* [http://www.electronic-things.de/shop electronic-things] - Deutscher Anbieter aller benötigten Teile und vollständiger Kits für Mendel, Mendel90 und Prusa -- [Deutschland/EU]<br />
* [http://reprapsource.com/de/prusa_mendel_kit Reprapsource] - Anbieter eines vollständigen Prusa Mendel Kits<br />
* [http://reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von vollständigen Kits für Prusa Mendel i2, MendelMax 1.5 und Prusa i3<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Druck Shop Berlin] - Berliner Anbieter eines Prusa Mendel i3 Kits (Einstein Version) [Deutschland/EU]<br />
<br />
===Elektronik- und Mechanikkits und -teile===<br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller benötigten Komponenten für den Drucker Bau ( Mechanik, Elektronik, Motoren, Zubehör, Filament, Extruder,Hotends und alles weitere )<br />
* [http://geeksbase.com/shop/ GeeksBase] - Anbieter von Teilekits und Platinen. Gedruckte Kunststoffsets(ABS).(Deutschland)<br />
* [[Generation 7 Electronics]] direkt vom Entwickler [mailto:mah@jump-ing.de Traumflug]<br />
* [http://profounddevices.com/ ProfoundDevices] - Anbieter eines vollständigen Teilekits für den [[Mendel Variations/Catalyst]] -- Elektronik, Kunststoffe (PU), Gewindestangen, Schrauben etc. (Oregon/USA)<br />
* [http://makerbot.com/ Makerbot] - Anbieter von fertigen und Bauteil-Kits / Platinenkits für die dritte Generation der RepRap-Elektronik und Extruderteilen. (New York/USA)<br />
* [http://www.bitsfrombytes.com/ Bits from Bytes] - Anbieter von Kunstoffdraht und alternativer Elektronik (kein RepRap Standard)<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://www.reprapsource.com/ RepRap Source] - Anbieter von Kunststoffdraht, Platinen der älteren Generation und mechanischen Teilen.<br />
* [http://www.iprint3d.org/ iPrint3D] - Anbieter der dritten Generation der RepRap-Elektronik<br />
* [https://shop.grrf.de/index.php?main_page= German RepRap Foundation (GRRF)] - Deutscher Anbieter von fertigen Kits für die dritte Generation der RepRap-Elektronik, Extruderteile, Schrittmotoren, Kunststoffe (ABS), Mechanik-Kits und RepStrap-Kits.<br />
* [http://kd85.com/ KD85.com] - Anbieter von RepRap-Teilen und Materialien in Europa.<br />
*[http://www.pololu.com/catalog/product/1182 Pololu ] - Anbieter eines alternativen Schrittmotortreibers, für mehr Informationen Siehe [[Pololu Electronics|Pololu Elektronik]]<br />
** Innerhalb Deutschlands kann man Pololus bei [http://www.lipoly.de/index.php?main_page=product_info&products_id=181885 diesem], [https://shop.grrf.de/pololu-a4983-stepper-motor-driver-carrier-p-297.html diesem] und [http://www.watterott.com/de/Pololu-A4988-Schrittmotortreiber diesem] Shop bestellen.<br />
** Alternativ kann auch ein [[Stepstick]] verwendet werden, welcher in Deutschland [http://www.ebay.de/itm/Stepstick-A4983-stepper-driver-board-RepRap-/300579027699 hier] billiger zu erhalten ist.<br />
* [http://ultimachine.com/ UltiMachine] - Anbieter von Elektronik, Mechanischen Teilen und Druckmaterial.<br />
* [http://www.reprapstores.com/ RepRap Stores] - Mehrere Anbieter und RepRapper, die Kits, Teile und Materialien verkaufen.<br />
* [http://www.2printbeta.de 2PrintBeta] - Anbieter von Kugellager- , Schrauben- , Zahnriemen- und Stangenkits und vielem mehr.<br />
* [http://www.cubic-print.de Cubic Print] Anbieter von Kunststoffteilen, Prusa Hardware Sets, Alu Platten, Kugellager, LM8UU, usw.<br />
* [http://reprapteile.de RepRapteile] - Prusa i3<br />
* [http://www.reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von Kits und Teilen für Prusa Mendel i2, MendelMax 1.5 und Prusa i3 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Lager, Hotends und Zubehör)<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Drucker Shop in Berlin] - 3D Drucker Shop in Berlin mit 3D Drucker Bausätzen und Teile für Prusa Mendel i3, so wie Reparatur, Verleih und Verkauf von neuen und gebrauchten 3D Druckern (z.B. Irapid, Rostock und Mendel i2)<br />
<br />
===Ge''RepRap''te Teilekits ===<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://reprap.cc Reprap-Austria] - Anbieter von Prusa Teilen aus ABS, Mendel Max und alle weiteren Kits auf Anfrage<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Druck Shop Berlin] - Berliner Anbieter von Prusa Teilen aus ABS und PLA. Druck von Ersatzteilen auch direkt vor Ort im Laden möglich.<br />
<br />
==Anbieter für Mendel-Teile==<br />
* [http://reprap.cc Reprap-Austria] - Anbieter von Teilesets für Mendel, Prusa, Mendel Max, Huxley, Rostock ( Kontakt Formular ).<br />
* [http://geeksbase.com/shop/ GeeksBase] bietet Teilesätze für einen Mendel in ABS an.<br />
* [http://fab.senselab.org sense.fab] bietet bis dahin Teilesätze für einen [[LaserCut Mendel]] an.<br />
* [http://www.reprap-fab.org reprap-fab] bietet Teilesätze für einen Mendel, Prusar, Huxley in ABS an.<br />
* [http://www.2printbeta.de 2PrintBeta] bietet Teilesätze für Mendel, Prusa und Huxley in PLA und gegossen in PU an.<br />
* [http://www.cubic-print.de Cubic Print] bietet Teilesätze für Mendel und Prusa in ABS an.<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von ABS Teilen für Mendel, Prusa und Mendel90<br />
* [http://reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von Teilen (ABS/PLA) für Prusa Mendel i2, MendelMax 1.5 und Prusa i3<br />
<br />
===Schrittmotoren===<br />
*[[Suppliers/Stepper Motors|Anbieter/Schrittmotoren]] - Enthält Details um festzustellen, ob ein Motor geeignet ist.<br />
<br />
===Elektronik===<br />
<br />
* [[Generation 7 Electronics]] Leiterplatten und Bauteilzusammenstellungen von [mailto:mah@jump-ing.de Traumflug]<br />
* [http://www.conrad.de/ Conrad Elektronik] - '''(Läden/online)'''<br />
* [http://www.reichelt.de/ Reichelt] - '''(online)'''<br />
* [http://www.digikey.com/ digikey US] - '''(online)'''<br />
* [http://www.digikey.ca/ digikey Canada] - '''Canada (online)'''<br />
* [http://mouser.com Mouser] - '''online'''<br />
* [http://reprapteile.de/elektronik.html?___store=en RepRapteile.de] - '''Europe''' - Ramps 1.4, Arduino, ... <br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller elektronischen Komponenten für Prusa und ähnliche Drucker.<br />
<br />
===Mechanik===<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller mechanischen Teile für Prusa, MendelMax, Rostock und ähnliche Drucker.<br />
* [http://www.mcmaster.com/ McMaster-Carr] - '''Versand nur innerhalb der USA(online)''' - Anbieter für alle nicht druckbaren mechanischen Teile für Mendel.<br />
* [http://www.fastenal.com/web/home.ex Fastenal] - '''Kanada und USA (Läden/online)''' - Anbieter für alle nicht druckbaren mechanischen Teile außer den Synchronriemen.<br />
* [http://www.sdp-si.com/web/html/products.htm SDP/SI] - '''Kanada (online)''' - Anbieter für nicht druckbare mechanische Teile inklusive Synchronriemen (es ist nicht bekannt ob alle nicht druckbaren Teile angeboten werden oder nicht).<br />
* [http://www.kugellager-express.de/ Kugellager - Express] - '''Deutschland''' - Deutscher Anbieter für Kugellager<br />
* [http://www.2printbeta.de 2PrintBeta] - '''Deutschland''' - Anbieter für alle nicht druckbaren mechanischen Teile für Mendel.<br />
* [http://reprapteile.de?___store=en RepRapteile]- '''Europe''' - Bearings, Timing Belts, Pulleys<br />
<br />
==Anbieter von Druckmaterial==<br />
Für Anbieter von ABS/PLA/Etc. siehe [[Printing Material Suppliers|Anbieter von Druckmaterial]]<br />
<br />
==Zu-Verkaufen-Forum==<br />
* RepRap-Teile werden außerdem im [http://forums.reprap.org/list.php?94 RepRap Zu-Verkaufen-Forum] angeboten.<br />
<br />
[[Category:Anbieter]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Mendel_Einkaufsf%C3%BChrer&diff=141911Mendel Einkaufsführer2015-01-16T14:28:41Z<p>Merlucin: /* GeRepRapte Teilekits */</p>
<hr />
<div>{{RepRapNavigation (Deutsch)|name=Mendel}}<br />
<br />
RepRap II: Mendel ist Open Source, daher gibt es keinen einzelnen Ort, um die Maschine zu kaufen, sondern viele verschiedene Möglichkeiten. Dieser Wettbewerb ist gewollt, so dass die Preise mit der Zeit sinken. Unten ist eine Liste der Quellen, woher man Mendel-Teile und/oder Kits bekommt.<br />
<br />
Für eine Excel-Tabelle, die eine komplette Liste der Mendel-Teile mit einer Auflistung der Lieferanten enthält, [[Mendel_assembly_data_sheet |siehe hier]].<br />
<br />
'''Anmerkung:''' Es ist nicht nötig, ein Kit zu kaufen, es gibt viele [[:Category:Mendel RepStrap|RepStraps]] zu kaufen oder zu bauen, die leicht mit den Werkzeugen zusammengebaut werden können, die man bereits besitzt.<br />
<br />
==Zu-Verkaufen-Forum==<br />
<br />
Wir haben ein [http://dev.forums.reprap.org/index.php?93 Zu-Verkaufen/Gesucht-Forum] wo sich jeder, der RepRap-Teile verkaufen oder kaufen möchte, eintragen kann. ''Caveat emptor'' - Wir versuchen, Schwindler und Betrüger aus dem Forum fernzuhalten, es ist jedoch weltweit zugänglich. Man sollte niemals Geld versenden, ohne sich darüber im Klaren zu sein, was man tut.<br />
<br />
==Fertig zusammengebaute Mendel-Kits==<br />
<br />
* X400 CE - Fertig zusammengebauter und CE-zertifizierter X400-Drucker, der auf RepRap basiert - siehe [https://shop.germanreprap.com/de germanreprap.com]<br />
<br />
* Prusa i3 - Fertig zusammengebauter Prusa i3 Reprap 3D Drucker - siehe [http://www.reprapuniverse.com ReprapUniverse.com]<br />
<br />
* Es gibt bisher keine Mendel-Kits, sobald es jedoch welche gibt, bitte hier eintragen.<br />
<br />
==Mendel-Teilekits==<br />
===Vollständige Kits===<br />
* [http://reprap.cc Reprap-Austria] - Anbieter eines vollständigen Prusa Mendel , MendelMax und Rostock Kits<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://www.mendel-parts.com/ Mendel-Parts] - Anbieter eines vollständigen Mendel kit -- Elektronik, Kunststoffe (PU), Gewindestangen, Schrauben, Extruder usw. (Niederland/EU)<br />
* [http://www.2printbeta.de/ 2PrintBeta] - Anbieter aller benötigten Teile für Mendel und Prusa -- [Deutschland/EU]<br />
* [http://www.electronic-things.de/shop electronic-things] - Deutscher Anbieter aller benötigten Teile und vollständiger Kits für Mendel, Mendel90 und Prusa -- [Deutschland/EU]<br />
* [http://reprapsource.com/de/prusa_mendel_kit Reprapsource] - Anbieter eines vollständigen Prusa Mendel Kits<br />
* [http://reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von vollständigen Kits für Prusa Mendel i2, MendelMax 1.5 und Prusa i3<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Druck Shop Berlin] - Berliner Anbieter eines Prusa Mendel i3 Kits (Einstein Version) [Deutschland/EU]<br />
<br />
===Elektronik- und Mechanikkits und -teile===<br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller benötigten Komponenten für den Drucker Bau ( Mechanik, Elektronik, Motoren, Zubehör, Filament, Extruder,Hotends und alles weitere )<br />
* [http://geeksbase.com/shop/ GeeksBase] - Anbieter von Teilekits und Platinen. Gedruckte Kunststoffsets(ABS).(Deutschland)<br />
* [[Generation 7 Electronics]] direkt vom Entwickler [mailto:mah@jump-ing.de Traumflug]<br />
* [http://profounddevices.com/ ProfoundDevices] - Anbieter eines vollständigen Teilekits für den [[Mendel Variations/Catalyst]] -- Elektronik, Kunststoffe (PU), Gewindestangen, Schrauben etc. (Oregon/USA)<br />
* [http://makerbot.com/ Makerbot] - Anbieter von fertigen und Bauteil-Kits / Platinenkits für die dritte Generation der RepRap-Elektronik und Extruderteilen. (New York/USA)<br />
* [http://www.bitsfrombytes.com/ Bits from Bytes] - Anbieter von Kunstoffdraht und alternativer Elektronik (kein RepRap Standard)<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://www.reprapsource.com/ RepRap Source] - Anbieter von Kunststoffdraht, Platinen der älteren Generation und mechanischen Teilen.<br />
* [http://www.iprint3d.org/ iPrint3D] - Anbieter der dritten Generation der RepRap-Elektronik<br />
* [https://shop.grrf.de/index.php?main_page= German RepRap Foundation (GRRF)] - Deutscher Anbieter von fertigen Kits für die dritte Generation der RepRap-Elektronik, Extruderteile, Schrittmotoren, Kunststoffe (ABS), Mechanik-Kits und RepStrap-Kits.<br />
* [http://kd85.com/ KD85.com] - Anbieter von RepRap-Teilen und Materialien in Europa.<br />
*[http://www.pololu.com/catalog/product/1182 Pololu ] - Anbieter eines alternativen Schrittmotortreibers, für mehr Informationen Siehe [[Pololu Electronics|Pololu Elektronik]]<br />
** Innerhalb Deutschlands kann man Pololus bei [http://www.lipoly.de/index.php?main_page=product_info&products_id=181885 diesem], [https://shop.grrf.de/pololu-a4983-stepper-motor-driver-carrier-p-297.html diesem] und [http://www.watterott.com/de/Pololu-A4988-Schrittmotortreiber diesem] Shop bestellen.<br />
** Alternativ kann auch ein [[Stepstick]] verwendet werden, welcher in Deutschland [http://www.ebay.de/itm/Stepstick-A4983-stepper-driver-board-RepRap-/300579027699 hier] billiger zu erhalten ist.<br />
* [http://ultimachine.com/ UltiMachine] - Anbieter von Elektronik, Mechanischen Teilen und Druckmaterial.<br />
* [http://www.reprapstores.com/ RepRap Stores] - Mehrere Anbieter und RepRapper, die Kits, Teile und Materialien verkaufen.<br />
* [http://www.2printbeta.de 2PrintBeta] - Anbieter von Kugellager- , Schrauben- , Zahnriemen- und Stangenkits und vielem mehr.<br />
* [http://www.cubic-print.de Cubic Print] Anbieter von Kunststoffteilen, Prusa Hardware Sets, Alu Platten, Kugellager, LM8UU, usw.<br />
* [http://reprapteile.de RepRapteile] - Prusa i3<br />
* [http://www.reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von Kits und Teilen für Prusa Mendel i2, MendelMax 1.5 und Prusa i3 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Lager, Hotends und Zubehör)<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Drucker Shop in Berlin] - 3D Drucker Shop in Berlin mit 3D Drucker Bausätzen und Teile für Prusa Mendel i3, so wie Reparatur, Verleih und Verkauf von neuen und gebrauchten 3D Druckern (z.B. Irapid, Rostock und Mendel i2)<br />
<br />
===Ge''RepRap''te Teilekits ===<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://reprap.cc Reprap-Austria] - Anbieter von Prusa Teilen aus ABS, Mendel Max und alle weiteren Kits auf Anfrage<br />
* [http://3D-Druck-Shop.YOUin3D.com 3D Druck Shop Berlin] - Berliner Anbieter von Prusa Teilen aus ABS und PLA. Druck von Ersatzteilen auch direkt vor Ort im Laden möglich.<br />
* [http://thingibox.com] - Spanischer Anbieter von Teilen für Mendel, Prusa u.a.<br />
<br />
==Anbieter für Mendel-Teile==<br />
* [http://reprap.cc Reprap-Austria] - Anbieter von Teilesets für Mendel, Prusa, Mendel Max, Huxley, Rostock ( Kontakt Formular ).<br />
* [http://geeksbase.com/shop/ GeeksBase] bietet Teilesätze für einen Mendel in ABS an.<br />
* [http://fab.senselab.org sense.fab] bietet bis dahin Teilesätze für einen [[LaserCut Mendel]] an.<br />
* [http://www.reprap-fab.org reprap-fab] bietet Teilesätze für einen Mendel, Prusar, Huxley in ABS an.<br />
* [http://www.2printbeta.de 2PrintBeta] bietet Teilesätze für Mendel, Prusa und Huxley in PLA und gegossen in PU an.<br />
* [http://www.cubic-print.de Cubic Print] bietet Teilesätze für Mendel und Prusa in ABS an.<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von ABS Teilen für Mendel, Prusa und Mendel90<br />
* [http://reprapuniverse.com ReprapUniverse.com] - High-Quality Anbieter von Teilen (ABS/PLA) für Prusa Mendel i2, MendelMax 1.5 und Prusa i3<br />
<br />
===Schrittmotoren===<br />
*[[Suppliers/Stepper Motors|Anbieter/Schrittmotoren]] - Enthält Details um festzustellen, ob ein Motor geeignet ist.<br />
<br />
===Elektronik===<br />
<br />
* [[Generation 7 Electronics]] Leiterplatten und Bauteilzusammenstellungen von [mailto:mah@jump-ing.de Traumflug]<br />
* [http://www.conrad.de/ Conrad Elektronik] - '''(Läden/online)'''<br />
* [http://www.reichelt.de/ Reichelt] - '''(online)'''<br />
* [http://www.digikey.com/ digikey US] - '''(online)'''<br />
* [http://www.digikey.ca/ digikey Canada] - '''Canada (online)'''<br />
* [http://mouser.com Mouser] - '''online'''<br />
* [http://reprapteile.de/elektronik.html?___store=en RepRapteile.de] - '''Europe''' - Ramps 1.4, Arduino, ... <br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller elektronischen Komponenten für Prusa und ähnliche Drucker.<br />
<br />
===Mechanik===<br />
* [http://www.electronic-things.de/shop/ electronic-things] - Deutscher Anbieter von Kits und Teilen für Mendel, Prusa und Mendel90 (Mechanik, Elektronik, Schrittmotoren, Schrauben, Federn, Lager, Hotends und Zubehör)<br />
* [http://reprap.cc Reprap-Austria] - Anbieter aller mechanischen Teile für Prusa, MendelMax, Rostock und ähnliche Drucker.<br />
* [http://www.mcmaster.com/ McMaster-Carr] - '''Versand nur innerhalb der USA(online)''' - Anbieter für alle nicht druckbaren mechanischen Teile für Mendel.<br />
* [http://www.fastenal.com/web/home.ex Fastenal] - '''Kanada und USA (Läden/online)''' - Anbieter für alle nicht druckbaren mechanischen Teile außer den Synchronriemen.<br />
* [http://www.sdp-si.com/web/html/products.htm SDP/SI] - '''Kanada (online)''' - Anbieter für nicht druckbare mechanische Teile inklusive Synchronriemen (es ist nicht bekannt ob alle nicht druckbaren Teile angeboten werden oder nicht).<br />
* [http://www.kugellager-express.de/ Kugellager - Express] - '''Deutschland''' - Deutscher Anbieter für Kugellager<br />
* [http://www.2printbeta.de 2PrintBeta] - '''Deutschland''' - Anbieter für alle nicht druckbaren mechanischen Teile für Mendel.<br />
* [http://reprapteile.de?___store=en RepRapteile]- '''Europe''' - Bearings, Timing Belts, Pulleys<br />
<br />
==Anbieter von Druckmaterial==<br />
Für Anbieter von ABS/PLA/Etc. siehe [[Printing Material Suppliers|Anbieter von Druckmaterial]]<br />
<br />
==Zu-Verkaufen-Forum==<br />
* RepRap-Teile werden außerdem im [http://forums.reprap.org/list.php?94 RepRap Zu-Verkaufen-Forum] angeboten.<br />
<br />
[[Category:Anbieter]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Clone_Wars:_Tiendas/es&diff=134100Clone Wars: Tiendas/es2014-10-17T21:17:25Z<p>Merlucin: Eliminados emails, publicidad innecesaria (esta página NO es un tablón de ofertas), corrección de faltas de ortografía y</p>
<hr />
<div>{{Languages|Clone_Wars:_Tiendas}} <br />
== Tiendas ==<br />
Sección donde se listan por orden alfabético las tiendas donde es posible encontrar componentes para tu impresora 3d:<br />
=== On-line España ===<br />
* [http://3dinvasion.com/ '''3Dinvasion'''] (España - Canarias) Venta de todos los componentes y filamento para impresoras 3D y talleres 3D. Envio 24h/48h a Canarias<br />
* [http://www.3dorobotics.com/tienda/ '''3DoRobotics'''] (España) Todo lo relacionado con la impresión 3D. Distribución de las mejores marcas. Servicio de impresión 3D bajo demanda.<br />
* [http://bcndynamics.com/ '''BCN Dynamics'''] (Barcelona) Tecnologia libre e impresoras 3D. Todos los componentes necesarios para montar impresoras 3D, desde tornillos sueltos, pasando por electrónica Arduino, hasta kits completos. Filamentos, suministros y mejoras.<br />
* [http://shop.createc3d.com '''Createc 3D shop''']: Lab y Makerspace en Granada con tienda física y online donde poder comprar cualquier cosa relacionada con la impresión 3D y tecnología Open Source. Cursos y talleres con formación continua.<br />
* [http://filamentoabs.com/ FilamentoABS] (España). Envíos gratis a Madrid [filamento]<br />
* [http://formate21.es/impresoras-3d/ Formate 21] (España) Venta de todos los componentes para impresoras 3D. Talleres 3D por toda España.<br />
* [http://ifusionshop.com/index.php iFusionShop] Componentes para impresoras 3D. Servicio de impresión y prototipado en 3D. También puedes solicitar la recogida en mano si eres de Tarragona, llamando al teléfono de la web<br />
* [http://www.igus.es/default.asp Igus] (España) Tienda especializada en rodamientos lineales sin bolas, cadenas porta cables en sistemas plásticas de alto rendimiento y mesas con husillo.<br />
* [http://impresoras3dlowcost.com Impresoras3DLowCost.com] (España)(Andalucía) Tenemos todo lo que necesitas para montar tu impresora 3D a los mejores precios, con atención personalizada y respuesta en menos de 24 horas.<br />
* [http://www.imprimiendoen3d.es IMPRIMIENDO EN 3D] (España) Tienda online con todo lo necesario para construir tu impresora 3d. Rodamientos, motores, electronica, varillas, filamento.<br />
* [http://www.iniciativas3d.com/ '''Iniciativas3D''' ](España) Tu tienda de impresión 3D en Córdoba. Kits y filamento. '''Sin costes de envío''' o recoge tu pedido en nuestra delegación en '''Córdoba''' o '''Málaga'''.<br />
* [http://www.kitprinter3d.com KITPRINTER3D ] 'Kits de Prusa i3 y P3Steel, ABS y PLA. Tienda física en el centro de Madrid.<br />
* [http://leapto3d.com/ LeapTo3D] (España) - Kits completos con TODO incluido. Recogida gratuita en Madrid. [filamento]<br />
* [http://www.lemonmaker.es/ LemonMaker] (España) Diseño & Impresión 3D. Kits impresoras 3D, workshops, componentes y filamento. Albacete, Madrid y Murcia.<br />
* [http://www.http://shop.menextech.com/index.php '''MENEXTECH'''] (España)'''Tienda renovada de Impresion 3d'''. Todo lo necesario para que construyas tu impresora y componentes informaticos. Una de las pioneras en impresion 3D en España.<br />
* [http://www.moebyus.com/ Moebyus Machines ](España) Sólo vendemos si tenemos stock. Entrega en 24h. Kits, marcos de metacrilato, filamento y todos los componentes necesarios para la prusa i3. Precios excelentes.<br />
* [http://printallthethings.com '''Print All the Things!!!'''] (España)(Galicia) Amplia variedad de colores PLA/ABS del bueno en 24h. También fabrican injectores jhead de gran calidad, y tienen camas calientes mk2b en negro con leds azules.<br />
* [http://www.printeddreams.es '''Printed Dreams'''] (España)(Madrid) Servicio 360° sobre impresión 3D. Kits impresora 3D, ABS/PLA en 18 colores diferentes,''' FILAFLEX y productos REPRAPBCN'''. info@printeddreams.es<br />
* [http://printhatshit.com PRINTHATSHIT - Easy 3D Printing -] (España) Tienda online y física en Barcelona. Todo lo que necesitas para montar tu Impresora 3D. Envío 24 horas y recogida en tienda.<br />
* [http://www.plabs3d.com PLABS 3D] (España) Gran servicio y calidad en todo tipo de materiales al mejor precio; PLA, ABS, HIPS, Nylon, Laywood, Laybrick, PVA, TPE, PS, Poikilothermal, Conductivo, Glow in the dark, etc!! mail: plabs3d@gmail.com.<br />
* [http://www.rationalstock.es/ Rational Stock] (España) Ferretería online. Variedad y buenos precios para tornillería. Permite comprar por unidades. Envío económico en 24-48 horas.<br />
* [http://shop.reclone3d.com/ Reclone3D] (España) Tienda de impresoras 3D.<br />
* [http://www.repparts3d.com/ '''RepParts 3D'''] (España) ABS, PLA, Conductor, Termocrómico, LayWood, LayBrick, Glow in the Dark, Nylon, HIPS. Con la mas amplia gama de colores<br />
* [http://www.staticboards.es/productos/ '''StaticBoards'''] (España) Fabrica Electrónica RAMPS 1.4SB Premium y Camas Calientes MK2B en Galicia.<br />
* [http://www.thingibox.com/ '''ThingiBOX'''] (España) Componentes y filamentos para impresoras 3D y otros proyectos oscuros.<br />
* [http://wi3dprint.com/ '''wi3Dprint'''] (España) Venta impresoras 3D, talleres, componentes y filamentos. Servicio de impresión<br />
<br />
=== On-line ===<br />
Europa:<br />
* [http://www.mendel-parts.com/ Mendel parts] (Holanda)<br />
* [http://www.xyzprinters.com/ http://www.xyzprinters.com/] (Holanda)<br />
* [http://shop.arcol.hu/ arcol.hu] (Hungría) <br />
* [https://shop.grrf.de/ German RepRap fundation] (Alemania)<br />
* [http://reprapsource.com/ reprapsource.com]<br />
* [http://reprapworld.com/ Reprap world] (Holanda) [filamento]<br />
* [https://0xfb.com/shop.html Future Bits] La tienda de Kliment! (Alemania)<br />
* [http://www.hotends.com/ hotends]<br />
* [http://www.orbi-tech.de/index_english.htm Orbi-tech]. Plástico (Alemania)<br />
* [http://reprap-3d-printer.com/ Reprap-3D-printer] (Francia)<br />
<br />
EEUU / América (ojo aduanas)<br />
* [http://www.makergear.com/ Makergear] (EEUU)<br />
* [http://www.lulzbot.com/en/ Lulzbot] (EEUU)<br />
* [http://gala-automation.com/ Gala automation] (EEUU)<br />
* [http://techpaladin.com/ techpaladin] (EEUU)<br />
* [http://www.centralreprap.com/prestashop/ CentralReprap]<br />
* [http://ultimachine.com/ Ultimachine] (EEUU)<br />
* [http://www.makermex.com/ MakerMex] (México)<br />
* [http://www.3dm.mx/ 3DM] (México) Impresoras 3D RepRap al Mejor Precio de México. Entrega Inmediata, consumibles y componentes.<br />
<br />
Otros <br />
* [http://www.3dacessorieshub.com/ 3D Acessories Hub ].Una ventanilla única para todos los componentes de RepRap y las impresoras 3D<br />
* [http://www.goodluckbuy.com/ http://www.goodluckbuy.com/]. Tienda en china donde venden motores, varillas roscadas...<br />
* [http://www.futurlec.com/ Futurlec] Electrónica en general<br />
* [http://www.taydaelectronics.com/ Tayda Electronics] Electrónica en general<br />
* [http://www.dealextreme.com/ Dealextreme] Tienda china con prácticamente cualquier cosa. (contrasta precios antes de comprar)<br />
* [http://www.bitsbox.co.uk/ BitsBox] Componentes electrónicos, algunos especialmente baratos. Envía por ~3€<br />
* [http://www.emakershop.com/ eMAKERshop] Tienda online que vende productos de varios vendedores externos, como un portal de venta.<br />
* [http://www.zappautomation.co.uk/index.php?language=ES Zappautomation] Tienda con todo tipo de productos para CNCs (UK)<br />
* [http://makemendel.com/ Makemendel]<br />
* [http://www.ebay.com/itm/1pc-200mm-X-100ft-High-Temperature-Resistant-Kapton-Tape-/170864710486?ssPageName=ADME:L:OU:ES:3160 Kapton en eBay]: Cinta kapton de 20cm de ancho<br />
* [http://www.reprap.cc/ Reprap Austria] Tienda de todo tipo de material para Reprap tambien en ebay: [http://www.ebay.es/sch/reprapper/m.html?_nkw=&_armrs=1&_from=&_ipg=&_trksid=p3686 reprapper]<br />
<br />
=== Físicas ===<br />
* [[Clone_wars:_Tiendas_en_Andalucia|Andalucía]]<br />
* [[Clone_wars:_Tiendas_en_asturias|Asturias]]<br />
* [[Clone_wars:_Tiendas_en_castellon|Castellón]]<br />
* [[Clone_wars:_Tiendas_en_galicia|Galicia]]<br />
* [[Clone_wars:_Tiendas_en_barcelona|Barcelona]]<br />
* [[Clone_wars:_Tiendas_en_madrid|Madrid]]<br />
* [[Clone_wars:_Tiendas_en_navarra|Navarra]]<br />
* [[Clone_wars:_Tiendas_en_Euskadi|Pais Vasco]]<br />
* [[Clone_wars:_Tiendas_en_valencia|Valencia]]<br />
* [[Clone_wars:_Tiendas_en_zaragoza|Zaragoza]]<br />
[http://goo.gl/maps/Md32Y Mapa] de tiendas y talleres<br />
<br />
=== Lista negra de tiendas ===<br />
Tiendas con las que hemos tenido malas experiencias:<br />
* [http://myworld.ebay.es/drumas09/ drumas09] (UK). Este vendedor no envía los pedidos. Pedro tuvo un problema con este vendedor.<br />
<br />
== Servicios de Corte ==<br />
<br />
'''Cortenfrio'''<br />
*Empresa de corte en frio ubicada en Zaragoza.<br />
*[http://cortenfrio.com/index.htm Cortenfrio]<br />
<br />
'''Laserebro'''<br />
*Son un grupo de empresas con muchas sedes, tienes una cerca de casa seguro :D mira en el mapa de localizacion, en su web, en el apartado: Grupo Láser Ebro.<br />
*[http://www.laserebro.com/frame1.htm Laserebro]<br />
<br />
'''Naivan'''<br />
*Empresa de corte por Laser y otros servicios en Vitoria.<br />
*[http://www.naivan.com/ Naivan]<br />
*Email para enviar los planos de corte: naivan@naivan.com (enviar en dxf o pdf acotado)<br />
*Teléfono:945 259 857<br />
<br />
'''HJL'''<br />
*Empresa de corte por Laser y otros servicios en Murcia.<br />
*[http://www.hjl.es/ HJL]<br />
*Teléfono:968 802 044<br />
<br />
'''ThingiBOX'''<br />
*Corte por Laser en Viladecans (Barcelona).<br />
*[http://www.thingibox.com/ ThingiBOX]<br />
*Teléfono: 93 590 39 39<br />
<br />
{| class="wikitable"<br />
|-<br />
|<br />
[[File:Clone-Wars-logo.png|border|100px|link=Proyecto Clone Wars]]<br />
| [[Proyecto Clone Wars]]<br />
|}<br />
<br />
[[Category:Clone wars/es]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Clone_Wars:_Tiendas/es&diff=130937Clone Wars: Tiendas/es2014-08-06T09:43:57Z<p>Merlucin: /* Servicios de Corte */</p>
<hr />
<div>{{Languages|Clone_Wars:_Tiendas}} <br />
== Tiendas ==<br />
Sección donde se listan por orden alfabético las tiendas donde es posible encontrar componentes para tu impresora 3d:<br />
=== On-line España ===<br />
* [http://3dinvasion.com/ '''3Dinvasion'''] (España - Canarias) Venta de todos los componentes y filamento para impresoras 3D y talleres 3D. Envio 24h/48h a Canarias<br />
* [http://www.3dorobotics.com/tienda/ '''3DoRobotics'''] (España) Todo lo relacionado con la impresión 3D. Distribución de las mejores marcas. Servicio de impresión 3D bajo demanda.<br />
* [http://shop.createc3d.com '''Createc 3D shop''']: Lab y Makerspace en Granada con tienda física y online donde poder comprar cualquier cosa relacionada con la impresión 3D y tecnología Open Source. Cursos y talleres con formación continua. '''Nuestros clientes están 100% satisfechos con la calidad y servicio técnico que ofrecemos'''. Entra y compruébalo tu mismo [http://www.createc3d.com Createc 3D]<br />
* [http://filamentoabs.com/ FilamentoABS] (España). Envíos gratis a Madrid [filamento]<br />
* [http://formate21.es/impresoras-3d/ Formate 21] (España) Venta de todos los componentes para impresoras 3D. Talleres 3D por toda España.<br />
* [http://ifusionshop.com/index.php iFusionShop] Todo lo básico para tu impresora 3D en la tienda mas molona! ;). Servicio de impresión y prototipado en 3D. También puedes solicitar la recogida en mano si eres de Tarragona, llamándonos al teléfono de la web<br />
* [http://www.igus.es/default.asp Igus] (España) Tienda especializada en rodamientos lineales sin bolas, cadenas porta cables en sistemas plásticas de alto rendimiento y mesas con husillo.<br />
* [http://impresoras3dlowcost.com Impresoras3DLowCost.com] (España)(Andalucía) Tenemos todo lo que necesitas para montar tu impresora 3D a los mejores precios, con atención personalizada y respuesta en menos de 24 horas.<br />
* [http://www.imprimiendoen3d.es IMPRIMIENDO EN 3D] (España) Tienda online con todo lo necesario para construir tu impresora 3d. Rodamientos, motores, electronica, varillas, filamento. Prusa I3 369€ IVA incluido<br />
* [http://www.iniciativas3d.com/ '''Iniciativas3D''' ](España) Tu tienda de impresión 3D en Córdoba. '''Kits desde 340€''', '''ABS/PLA desde 17€''', descubre porque la '''mejor calidad''' y el '''mejor precio''' no tienen que estar reñidos. '''Sin costes de envío''' o recoge tu pedido en nuestra delegación en '''Córdoba''' o '''Málaga'''.<br />
* [http://www.kitprinter3d.com KITPRINTER3D ] '''Prusa i3 a 399 € (IVA incluido)''', '''P3Steel por 409 € (IVA incluido)''', ABS y PLA. Tienda física en el centro de Madrid.<br />
* [http://leapto3d.com/ LeapTo3D] (España) - Kits completos con TODO incluido. Recogida gratuita en Madrid. [filamento]<br />
* [http://www.lemonmaker.es/ LemonMaker] (España) Diseño & Impresión 3D. Kits impresoras 3D, workshops, componentes y filamento. Albacete, Madrid y Murcia. [CUALQUIER COSA ES POSIBLE].<br />
* [http://www.http://shop.menextech.com/index.php '''MENEXTECH'''] (España)'''Tienda renovada de Impresion 3d'''. Todo lo necesario para que construyas tu impresora y componentes informaticos. Una de las pioneras en impresion 3D en España. Visitanos y no te arrepentiras. '''Kit Prusa 390€.'''<br />
* [http://www.moebyus.com/ Moebyus Machines ](España) Sólo vendemos si tenemos stock. Entrega en 24h. Kits, marcos de metacrilato, filamento y todos los componentes necesarios para la prusa i3. Precios excelentes.<br />
* [http://printallthethings.com Print All the Things!!!] (España) Multitud de colores PLA/ABS del bueno en tu casa al día siguiente. También fabrican injectores jhead de gran calidad, y tienen camas calientes mk2b espectaculares.<br />
* [http://www.printeddreams.es Printed Dreams] (España) Servicio 360° sobre impresión 3D. ¡La mejor calidad al mejor precio! Kit impresora 3D, ABS/PLA 16,95 € (IVA inc) el kilo con '''+ de 18 colores diferentes'''. Y muchas otras cosas. info@printeddreams.es<br />
* [http://printhatshit.com PRINTHATSHIT - Easy 3D Printing -] (España) Tienda online y física en Barcelona. Todo lo que necesitas para montar tu Impresora 3D. Envío 24 horas y recogida en tienda.<br />
* [http://www.plabs3d.com PLABS 3D] (España) Gran servicio y calidad en todo tipo de materiales al mejor precio; PLA, ABS, HIPS, Nylon, Laywood, Laybrick, PVA, TPE, PS, Poikilothermal, Conductivo, Glow in the dark, etc!! mail: plabs3d@gmail.com.<br />
* [http://www.rationalstock.es/ Rational Stock] (España) Ferretería online. Variedad y buenos precios para tornillería. Permite comprar por unidades. Envío económico en 24-48 horas.<br />
* [http://www.thingibox.com/ '''ThingiBOX'''] (España) Componentes y filamentos para impresoras 3D y otros proyectos opensource.<br />
* [http://wi3dprint.com/ '''wi3Dprint'''] (España) '''KIT PRUSA i3 HEPHESTOS: 449 Euros IVA Incl.''' Venta impresoras 3D, talleres, componentes y filamentos. Servicio de impresión<br />
<br />
=== On-line ===<br />
Europa:<br />
* [http://www.mendel-parts.com/ Mendel parts] (Holanda)<br />
* [http://www.xyzprinters.com/ http://www.xyzprinters.com/] (Holanda)<br />
* [http://shop.arcol.hu/ arcol.hu] (Hungría) <br />
* [https://shop.grrf.de/ German RepRap fundation] (Alemania)<br />
* [http://reprapsource.com/ reprapsource.com]<br />
* [http://reprapworld.com/ Reprap world] (Holanda) [filamento]<br />
* [https://0xfb.com/shop.html Future Bits] La tienda de Kliment! (Alemania)<br />
* [http://www.hotends.com/ hotends]<br />
* [http://www.orbi-tech.de/index_english.htm Orbi-tech]. Plástico (Alemania)<br />
* [http://reprap-3d-printer.com/ Reprap-3D-printer] (Francia)<br />
<br />
EEUU / América (ojo aduanas)<br />
* [http://www.makergear.com/ Makergear] (EEUU)<br />
* [http://www.lulzbot.com/en/ Lulzbot] (EEUU)<br />
* [http://gala-automation.com/ Gala automation] (EEUU)<br />
* [http://techpaladin.com/ techpaladin] (EEUU)<br />
* [http://www.centralreprap.com/prestashop/ CentralReprap]<br />
* [http://ultimachine.com/ Ultimachine] (EEUU)<br />
* [http://www.makermex.com/ MakerMex] (México)<br />
<br />
Otros <br />
* [http://www.3dacessorieshub.com/ 3D Acessories Hub ].Una ventanilla única para todos los componentes de RepRap y las impresoras 3D<br />
* [http://www.goodluckbuy.com/ http://www.goodluckbuy.com/]. Tienda en china donde venden motores, varillas roscadas...<br />
* [http://www.futurlec.com/ Futurlec] Electrónica en general<br />
* [http://www.taydaelectronics.com/ Tayda Electronics] Electrónica en general<br />
* [http://www.dealextreme.com/ Dealextreme] Tienda china con prácticamente cualquier cosa. (contrasta precios antes de comprar)<br />
* [http://www.bitsbox.co.uk/ BitsBox] Componentes electrónicos, algunos especialmente baratos. Envía por ~3€<br />
* [http://www.emakershop.com/ eMAKERshop] Tienda online que vende productos de varios vendedores externos, como un portal de venta.<br />
* [http://www.zappautomation.co.uk/index.php?language=ES Zappautomation] Tienda con todo tipo de productos para CNCs (UK)<br />
* [http://makemendel.com/ Makemendel]<br />
* [http://www.ebay.com/itm/1pc-200mm-X-100ft-High-Temperature-Resistant-Kapton-Tape-/170864710486?ssPageName=ADME:L:OU:ES:3160 Kapton en eBay]: Cinta kapton de 20cm de ancho<br />
* [http://www.reprap.cc/ Reprap Austria] Tienda de todo tipo de material para Reprap tambien en ebay: [http://www.ebay.es/sch/reprapper/m.html?_nkw=&_armrs=1&_from=&_ipg=&_trksid=p3686 reprapper]<br />
<br />
=== Físicas ===<br />
* [[Clone_wars:_Tiendas_en_Andalucia|Andalucía]]<br />
* [[Clone_wars:_Tiendas_en_asturias|Asturias]]<br />
* [[Clone_wars:_Tiendas_en_castellon|Castellón]]<br />
* [[Clone_wars:_Tiendas_en_galicia|Galicia]]<br />
* [[Clone_wars:_Tiendas_en_barcelona|Barcelona]]<br />
* [[Clone_wars:_Tiendas_en_madrid|Madrid]]<br />
* [[Clone_wars:_Tiendas_en_navarra|Navarra]]<br />
* [[Clone_wars:_Tiendas_en_valencia|Valencia]]<br />
* [[Clone_wars:_Tiendas_en_zaragoza|Zaragoza]]<br />
[http://goo.gl/maps/Md32Y Mapa] de tiendas y talleres<br />
<br />
=== Lista negra de tiendas ===<br />
Tiendas con las que hemos tenido malas experiencias:<br />
* [http://myworld.ebay.es/drumas09/ drumas09] (UK). Este vendedor no envía los pedidos. Pedro tuvo un problema con este vendedor.<br />
<br />
== Servicios de Corte ==<br />
<br />
'''Cortenfrio'''<br />
*Empresa de corte en frio ubicada en Zaragoza.<br />
*[http://cortenfrio.com/index.htm Cortenfrio]<br />
<br />
'''Laserebro'''<br />
*Son un grupo de empresas con muchas sedes, tienes una cerca de casa seguro :D mira en el mapa de localizacion, en su web, en el apartado: Grupo Láser Ebro.<br />
*[http://www.laserebro.com/frame1.htm Laserebro]<br />
<br />
'''Naivan'''<br />
*Empresa de corte por Laser y otros servicios en Vitoria.<br />
*[http://www.naivan.com/ Naivan]<br />
*Email para enviar los planos de corte: naivan@naivan.com (enviar en dxf o pdf acotado)<br />
*Teléfono:945 259 857<br />
<br />
'''HJL'''<br />
*Empresa de corte por Laser y otros servicios en Murcia.<br />
*[http://www.hjl.es/ HJL]<br />
*Teléfono:968 802 044<br />
<br />
'''ThingiBOX'''<br />
*Corte por Laser en Viladecans (Barcelona).<br />
*[http://www.thingibox.com/ ThingiBOX]<br />
*Teléfono: 93 590 39 39<br />
<br />
{| class="wikitable"<br />
|-<br />
|<br />
[[File:Clone-Wars-logo.png|border|100px|link=Proyecto Clone Wars]]<br />
| [[Proyecto Clone Wars]]<br />
|}<br />
<br />
[[Category:Clone wars/es]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Clone_Wars:_Tiendas/es&diff=130936Clone Wars: Tiendas/es2014-08-06T09:41:51Z<p>Merlucin: /* On-line España */</p>
<hr />
<div>{{Languages|Clone_Wars:_Tiendas}} <br />
== Tiendas ==<br />
Sección donde se listan por orden alfabético las tiendas donde es posible encontrar componentes para tu impresora 3d:<br />
=== On-line España ===<br />
* [http://3dinvasion.com/ '''3Dinvasion'''] (España - Canarias) Venta de todos los componentes y filamento para impresoras 3D y talleres 3D. Envio 24h/48h a Canarias<br />
* [http://www.3dorobotics.com/tienda/ '''3DoRobotics'''] (España) Todo lo relacionado con la impresión 3D. Distribución de las mejores marcas. Servicio de impresión 3D bajo demanda.<br />
* [http://shop.createc3d.com '''Createc 3D shop''']: Lab y Makerspace en Granada con tienda física y online donde poder comprar cualquier cosa relacionada con la impresión 3D y tecnología Open Source. Cursos y talleres con formación continua. '''Nuestros clientes están 100% satisfechos con la calidad y servicio técnico que ofrecemos'''. Entra y compruébalo tu mismo [http://www.createc3d.com Createc 3D]<br />
* [http://filamentoabs.com/ FilamentoABS] (España). Envíos gratis a Madrid [filamento]<br />
* [http://formate21.es/impresoras-3d/ Formate 21] (España) Venta de todos los componentes para impresoras 3D. Talleres 3D por toda España.<br />
* [http://ifusionshop.com/index.php iFusionShop] Todo lo básico para tu impresora 3D en la tienda mas molona! ;). Servicio de impresión y prototipado en 3D. También puedes solicitar la recogida en mano si eres de Tarragona, llamándonos al teléfono de la web<br />
* [http://www.igus.es/default.asp Igus] (España) Tienda especializada en rodamientos lineales sin bolas, cadenas porta cables en sistemas plásticas de alto rendimiento y mesas con husillo.<br />
* [http://impresoras3dlowcost.com Impresoras3DLowCost.com] (España)(Andalucía) Tenemos todo lo que necesitas para montar tu impresora 3D a los mejores precios, con atención personalizada y respuesta en menos de 24 horas.<br />
* [http://www.imprimiendoen3d.es IMPRIMIENDO EN 3D] (España) Tienda online con todo lo necesario para construir tu impresora 3d. Rodamientos, motores, electronica, varillas, filamento. Prusa I3 369€ IVA incluido<br />
* [http://www.iniciativas3d.com/ '''Iniciativas3D''' ](España) Tu tienda de impresión 3D en Córdoba. '''Kits desde 340€''', '''ABS/PLA desde 17€''', descubre porque la '''mejor calidad''' y el '''mejor precio''' no tienen que estar reñidos. '''Sin costes de envío''' o recoge tu pedido en nuestra delegación en '''Córdoba''' o '''Málaga'''.<br />
* [http://www.kitprinter3d.com KITPRINTER3D ] '''Prusa i3 a 399 € (IVA incluido)''', '''P3Steel por 409 € (IVA incluido)''', ABS y PLA. Tienda física en el centro de Madrid.<br />
* [http://leapto3d.com/ LeapTo3D] (España) - Kits completos con TODO incluido. Recogida gratuita en Madrid. [filamento]<br />
* [http://www.lemonmaker.es/ LemonMaker] (España) Diseño & Impresión 3D. Kits impresoras 3D, workshops, componentes y filamento. Albacete, Madrid y Murcia. [CUALQUIER COSA ES POSIBLE].<br />
* [http://www.http://shop.menextech.com/index.php '''MENEXTECH'''] (España)'''Tienda renovada de Impresion 3d'''. Todo lo necesario para que construyas tu impresora y componentes informaticos. Una de las pioneras en impresion 3D en España. Visitanos y no te arrepentiras. '''Kit Prusa 390€.'''<br />
* [http://www.moebyus.com/ Moebyus Machines ](España) Sólo vendemos si tenemos stock. Entrega en 24h. Kits, marcos de metacrilato, filamento y todos los componentes necesarios para la prusa i3. Precios excelentes.<br />
* [http://printallthethings.com Print All the Things!!!] (España) Multitud de colores PLA/ABS del bueno en tu casa al día siguiente. También fabrican injectores jhead de gran calidad, y tienen camas calientes mk2b espectaculares.<br />
* [http://www.printeddreams.es Printed Dreams] (España) Servicio 360° sobre impresión 3D. ¡La mejor calidad al mejor precio! Kit impresora 3D, ABS/PLA 16,95 € (IVA inc) el kilo con '''+ de 18 colores diferentes'''. Y muchas otras cosas. info@printeddreams.es<br />
* [http://printhatshit.com PRINTHATSHIT - Easy 3D Printing -] (España) Tienda online y física en Barcelona. Todo lo que necesitas para montar tu Impresora 3D. Envío 24 horas y recogida en tienda.<br />
* [http://www.plabs3d.com PLABS 3D] (España) Gran servicio y calidad en todo tipo de materiales al mejor precio; PLA, ABS, HIPS, Nylon, Laywood, Laybrick, PVA, TPE, PS, Poikilothermal, Conductivo, Glow in the dark, etc!! mail: plabs3d@gmail.com.<br />
* [http://www.rationalstock.es/ Rational Stock] (España) Ferretería online. Variedad y buenos precios para tornillería. Permite comprar por unidades. Envío económico en 24-48 horas.<br />
* [http://www.thingibox.com/ '''ThingiBOX'''] (España) Componentes y filamentos para impresoras 3D y otros proyectos opensource.<br />
* [http://wi3dprint.com/ '''wi3Dprint'''] (España) '''KIT PRUSA i3 HEPHESTOS: 449 Euros IVA Incl.''' Venta impresoras 3D, talleres, componentes y filamentos. Servicio de impresión<br />
<br />
=== On-line ===<br />
Europa:<br />
* [http://www.mendel-parts.com/ Mendel parts] (Holanda)<br />
* [http://www.xyzprinters.com/ http://www.xyzprinters.com/] (Holanda)<br />
* [http://shop.arcol.hu/ arcol.hu] (Hungría) <br />
* [https://shop.grrf.de/ German RepRap fundation] (Alemania)<br />
* [http://reprapsource.com/ reprapsource.com]<br />
* [http://reprapworld.com/ Reprap world] (Holanda) [filamento]<br />
* [https://0xfb.com/shop.html Future Bits] La tienda de Kliment! (Alemania)<br />
* [http://www.hotends.com/ hotends]<br />
* [http://www.orbi-tech.de/index_english.htm Orbi-tech]. Plástico (Alemania)<br />
* [http://reprap-3d-printer.com/ Reprap-3D-printer] (Francia)<br />
<br />
EEUU / América (ojo aduanas)<br />
* [http://www.makergear.com/ Makergear] (EEUU)<br />
* [http://www.lulzbot.com/en/ Lulzbot] (EEUU)<br />
* [http://gala-automation.com/ Gala automation] (EEUU)<br />
* [http://techpaladin.com/ techpaladin] (EEUU)<br />
* [http://www.centralreprap.com/prestashop/ CentralReprap]<br />
* [http://ultimachine.com/ Ultimachine] (EEUU)<br />
* [http://www.makermex.com/ MakerMex] (México)<br />
<br />
Otros <br />
* [http://www.3dacessorieshub.com/ 3D Acessories Hub ].Una ventanilla única para todos los componentes de RepRap y las impresoras 3D<br />
* [http://www.goodluckbuy.com/ http://www.goodluckbuy.com/]. Tienda en china donde venden motores, varillas roscadas...<br />
* [http://www.futurlec.com/ Futurlec] Electrónica en general<br />
* [http://www.taydaelectronics.com/ Tayda Electronics] Electrónica en general<br />
* [http://www.dealextreme.com/ Dealextreme] Tienda china con prácticamente cualquier cosa. (contrasta precios antes de comprar)<br />
* [http://www.bitsbox.co.uk/ BitsBox] Componentes electrónicos, algunos especialmente baratos. Envía por ~3€<br />
* [http://www.emakershop.com/ eMAKERshop] Tienda online que vende productos de varios vendedores externos, como un portal de venta.<br />
* [http://www.zappautomation.co.uk/index.php?language=ES Zappautomation] Tienda con todo tipo de productos para CNCs (UK)<br />
* [http://makemendel.com/ Makemendel]<br />
* [http://www.ebay.com/itm/1pc-200mm-X-100ft-High-Temperature-Resistant-Kapton-Tape-/170864710486?ssPageName=ADME:L:OU:ES:3160 Kapton en eBay]: Cinta kapton de 20cm de ancho<br />
* [http://www.reprap.cc/ Reprap Austria] Tienda de todo tipo de material para Reprap tambien en ebay: [http://www.ebay.es/sch/reprapper/m.html?_nkw=&_armrs=1&_from=&_ipg=&_trksid=p3686 reprapper]<br />
<br />
=== Físicas ===<br />
* [[Clone_wars:_Tiendas_en_Andalucia|Andalucía]]<br />
* [[Clone_wars:_Tiendas_en_asturias|Asturias]]<br />
* [[Clone_wars:_Tiendas_en_castellon|Castellón]]<br />
* [[Clone_wars:_Tiendas_en_galicia|Galicia]]<br />
* [[Clone_wars:_Tiendas_en_barcelona|Barcelona]]<br />
* [[Clone_wars:_Tiendas_en_madrid|Madrid]]<br />
* [[Clone_wars:_Tiendas_en_navarra|Navarra]]<br />
* [[Clone_wars:_Tiendas_en_valencia|Valencia]]<br />
* [[Clone_wars:_Tiendas_en_zaragoza|Zaragoza]]<br />
[http://goo.gl/maps/Md32Y Mapa] de tiendas y talleres<br />
<br />
=== Lista negra de tiendas ===<br />
Tiendas con las que hemos tenido malas experiencias:<br />
* [http://myworld.ebay.es/drumas09/ drumas09] (UK). Este vendedor no envía los pedidos. Pedro tuvo un problema con este vendedor.<br />
<br />
== Servicios de Corte ==<br />
<br />
'''Cortenfrio'''<br />
*Empresa de corte en frio ubicada en Zaragoza.<br />
*[http://cortenfrio.com/index.htm Cortenfrio]<br />
<br />
'''Laserebro'''<br />
*Son un grupo de empresas con muchas sedes, tienes una cerca de casa seguro :D mira en el mapa de localizacion, en su web, en el apartado: Grupo Láser Ebro.<br />
*[http://www.laserebro.com/frame1.htm Laserebro]<br />
<br />
'''Naivan'''<br />
*Empresa de corte por Laser y otros servicios en Vitoria.<br />
*[http://www.naivan.com/ Naivan]<br />
*Email para enviar los planos de corte: naivan@naivan.com (enviar en dxf o pdf acotado)<br />
*Teléfono:945 259 857<br />
<br />
'''HJL'''<br />
*Empresa de corte por Laser y otros servicios en Murcia.<br />
*[http://www.hjl.es/ HJL]<br />
*Teléfono:968 802 044<br />
<br />
{| class="wikitable"<br />
|-<br />
|<br />
[[File:Clone-Wars-logo.png|border|100px|link=Proyecto Clone Wars]]<br />
| [[Proyecto Clone Wars]]<br />
|}<br />
<br />
[[Category:Clone wars/es]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Clone_Wars:_Tiendas/es&diff=130935Clone Wars: Tiendas/es2014-08-06T09:41:23Z<p>Merlucin: /* On-line España */</p>
<hr />
<div>{{Languages|Clone_Wars:_Tiendas}} <br />
== Tiendas ==<br />
Sección donde se listan por orden alfabético las tiendas donde es posible encontrar componentes para tu impresora 3d:<br />
=== On-line España ===<br />
* [http://3dinvasion.com/ '''3Dinvasion'''] (España - Canarias) Venta de todos los componentes y filamento para impresoras 3D y talleres 3D. Envio 24h/48h a Canarias<br />
* [http://www.3dorobotics.com/tienda/ '''3DoRobotics'''] (España) Todo lo relacionado con la impresión 3D. Distribución de las mejores marcas. Servicio de impresión 3D bajo demanda.<br />
* [http://shop.createc3d.com '''Createc 3D shop''']: Lab y Makerspace en Granada con tienda física y online donde poder comprar cualquier cosa relacionada con la impresión 3D y tecnología Open Source. Cursos y talleres con formación continua. '''Nuestros clientes están 100% satisfechos con la calidad y servicio técnico que ofrecemos'''. Entra y compruébalo tu mismo [http://www.createc3d.com Createc 3D]<br />
* [http://filamentoabs.com/ FilamentoABS] (España). Envíos gratis a Madrid [filamento]<br />
* [http://formate21.es/impresoras-3d/ Formate 21] (España) Venta de todos los componentes para impresoras 3D. Talleres 3D por toda España.<br />
* [http://ifusionshop.com/index.php iFusionShop] Todo lo básico para tu impresora 3D en la tienda mas molona! ;). Servicio de impresión y prototipado en 3D. También puedes solicitar la recogida en mano si eres de Tarragona, llamándonos al teléfono de la web<br />
* [http://www.igus.es/default.asp Igus] (España) Tienda especializada en rodamientos lineales sin bolas, cadenas porta cables en sistemas plásticas de alto rendimiento y mesas con husillo.<br />
* [http://impresoras3dlowcost.com Impresoras3DLowCost.com] (España)(Andalucía) Tenemos todo lo que necesitas para montar tu impresora 3D a los mejores precios, con atención personalizada y respuesta en menos de 24 horas.<br />
* [http://www.imprimiendoen3d.es IMPRIMIENDO EN 3D] (España) Tienda online con todo lo necesario para construir tu impresora 3d. Rodamientos, motores, electronica, varillas, filamento. Prusa I3 369€ IVA incluido<br />
* [http://www.iniciativas3d.com/ '''Iniciativas3D''' ](España) Tu tienda de impresión 3D en Córdoba. '''Kits desde 340€''', '''ABS/PLA desde 17€''', descubre porque la '''mejor calidad''' y el '''mejor precio''' no tienen que estar reñidos. '''Sin costes de envío''' o recoge tu pedido en nuestra delegación en '''Córdoba''' o '''Málaga'''.<br />
* [http://www.kitprinter3d.com KITPRINTER3D ] '''Prusa i3 a 399 € (IVA incluido)''', '''P3Steel por 409 € (IVA incluido)''', ABS y PLA. Tienda física en el centro de Madrid.<br />
* [http://leapto3d.com/ LeapTo3D] (España) - Kits completos con TODO incluido. Recogida gratuita en Madrid. [filamento]<br />
* [http://www.lemonmaker.es/ LemonMaker] (España) Diseño & Impresión 3D. Kits impresoras 3D, workshops, componentes y filamento. Albacete, Madrid y Murcia. [CUALQUIER COSA ES POSIBLE].<br />
* [http://www.http://shop.menextech.com/index.php '''MENEXTECH'''] (España)'''Tienda renovada de Impresion 3d'''. Todo lo necesario para que construyas tu impresora y componentes informaticos. Una de las pioneras en impresion 3D en España. Visitanos y no te arrepentiras. '''Kit Prusa 390€.'''<br />
* [http://www.moebyus.com/ Moebyus Machines ](España) Sólo vendemos si tenemos stock. Entrega en 24h. Kits, marcos de metacrilato, filamento y todos los componentes necesarios para la prusa i3. Precios excelentes.<br />
* [http://printallthethings.com Print All the Things!!!] (España) Multitud de colores PLA/ABS del bueno en tu casa al día siguiente. También fabrican injectores jhead de gran calidad, y tienen camas calientes mk2b espectaculares.<br />
* [http://www.printeddreams.es Printed Dreams] (España) Servicio 360° sobre impresión 3D. ¡La mejor calidad al mejor precio! Kit impresora 3D, ABS/PLA 16,95 € (IVA inc) el kilo con '''+ de 18 colores diferentes'''. Y muchas otras cosas. info@printeddreams.es<br />
* [http://printhatshit.com PRINTHATSHIT - Easy 3D Printing -] (España) Tienda online y física en Barcelona. Todo lo que necesitas para montar tu Impresora 3D. Envío 24 horas y recogida en tienda.<br />
* [http://www.plabs3d.com PLABS 3D] (España) Gran servicio y calidad en todo tipo de materiales al mejor precio; PLA, ABS, HIPS, Nylon, Laywood, Laybrick, PVA, TPE, PS, Poikilothermal, Conductivo, Glow in the dark, etc!! mail: plabs3d@gmail.com.<br />
* [http://www.rationalstock.es/ Rational Stock] (España) Ferretería online. Variedad y buenos precios para tornillería. Permite comprar por unidades. Envío económico en 24-48 horas.<br />
* [http://www.thingibox.com/ ""ThingiBOX""] (España) Componentes y filamentos para impresoras 3D y otros proyectos opensource.<br />
* [http://wi3dprint.com/ '''wi3Dprint'''] (España) '''KIT PRUSA i3 HEPHESTOS: 449 Euros IVA Incl.''' Venta impresoras 3D, talleres, componentes y filamentos. Servicio de impresión<br />
<br />
=== On-line ===<br />
Europa:<br />
* [http://www.mendel-parts.com/ Mendel parts] (Holanda)<br />
* [http://www.xyzprinters.com/ http://www.xyzprinters.com/] (Holanda)<br />
* [http://shop.arcol.hu/ arcol.hu] (Hungría) <br />
* [https://shop.grrf.de/ German RepRap fundation] (Alemania)<br />
* [http://reprapsource.com/ reprapsource.com]<br />
* [http://reprapworld.com/ Reprap world] (Holanda) [filamento]<br />
* [https://0xfb.com/shop.html Future Bits] La tienda de Kliment! (Alemania)<br />
* [http://www.hotends.com/ hotends]<br />
* [http://www.orbi-tech.de/index_english.htm Orbi-tech]. Plástico (Alemania)<br />
* [http://reprap-3d-printer.com/ Reprap-3D-printer] (Francia)<br />
<br />
EEUU / América (ojo aduanas)<br />
* [http://www.makergear.com/ Makergear] (EEUU)<br />
* [http://www.lulzbot.com/en/ Lulzbot] (EEUU)<br />
* [http://gala-automation.com/ Gala automation] (EEUU)<br />
* [http://techpaladin.com/ techpaladin] (EEUU)<br />
* [http://www.centralreprap.com/prestashop/ CentralReprap]<br />
* [http://ultimachine.com/ Ultimachine] (EEUU)<br />
* [http://www.makermex.com/ MakerMex] (México)<br />
<br />
Otros <br />
* [http://www.3dacessorieshub.com/ 3D Acessories Hub ].Una ventanilla única para todos los componentes de RepRap y las impresoras 3D<br />
* [http://www.goodluckbuy.com/ http://www.goodluckbuy.com/]. Tienda en china donde venden motores, varillas roscadas...<br />
* [http://www.futurlec.com/ Futurlec] Electrónica en general<br />
* [http://www.taydaelectronics.com/ Tayda Electronics] Electrónica en general<br />
* [http://www.dealextreme.com/ Dealextreme] Tienda china con prácticamente cualquier cosa. (contrasta precios antes de comprar)<br />
* [http://www.bitsbox.co.uk/ BitsBox] Componentes electrónicos, algunos especialmente baratos. Envía por ~3€<br />
* [http://www.emakershop.com/ eMAKERshop] Tienda online que vende productos de varios vendedores externos, como un portal de venta.<br />
* [http://www.zappautomation.co.uk/index.php?language=ES Zappautomation] Tienda con todo tipo de productos para CNCs (UK)<br />
* [http://makemendel.com/ Makemendel]<br />
* [http://www.ebay.com/itm/1pc-200mm-X-100ft-High-Temperature-Resistant-Kapton-Tape-/170864710486?ssPageName=ADME:L:OU:ES:3160 Kapton en eBay]: Cinta kapton de 20cm de ancho<br />
* [http://www.reprap.cc/ Reprap Austria] Tienda de todo tipo de material para Reprap tambien en ebay: [http://www.ebay.es/sch/reprapper/m.html?_nkw=&_armrs=1&_from=&_ipg=&_trksid=p3686 reprapper]<br />
<br />
=== Físicas ===<br />
* [[Clone_wars:_Tiendas_en_Andalucia|Andalucía]]<br />
* [[Clone_wars:_Tiendas_en_asturias|Asturias]]<br />
* [[Clone_wars:_Tiendas_en_castellon|Castellón]]<br />
* [[Clone_wars:_Tiendas_en_galicia|Galicia]]<br />
* [[Clone_wars:_Tiendas_en_barcelona|Barcelona]]<br />
* [[Clone_wars:_Tiendas_en_madrid|Madrid]]<br />
* [[Clone_wars:_Tiendas_en_navarra|Navarra]]<br />
* [[Clone_wars:_Tiendas_en_valencia|Valencia]]<br />
* [[Clone_wars:_Tiendas_en_zaragoza|Zaragoza]]<br />
[http://goo.gl/maps/Md32Y Mapa] de tiendas y talleres<br />
<br />
=== Lista negra de tiendas ===<br />
Tiendas con las que hemos tenido malas experiencias:<br />
* [http://myworld.ebay.es/drumas09/ drumas09] (UK). Este vendedor no envía los pedidos. Pedro tuvo un problema con este vendedor.<br />
<br />
== Servicios de Corte ==<br />
<br />
'''Cortenfrio'''<br />
*Empresa de corte en frio ubicada en Zaragoza.<br />
*[http://cortenfrio.com/index.htm Cortenfrio]<br />
<br />
'''Laserebro'''<br />
*Son un grupo de empresas con muchas sedes, tienes una cerca de casa seguro :D mira en el mapa de localizacion, en su web, en el apartado: Grupo Láser Ebro.<br />
*[http://www.laserebro.com/frame1.htm Laserebro]<br />
<br />
'''Naivan'''<br />
*Empresa de corte por Laser y otros servicios en Vitoria.<br />
*[http://www.naivan.com/ Naivan]<br />
*Email para enviar los planos de corte: naivan@naivan.com (enviar en dxf o pdf acotado)<br />
*Teléfono:945 259 857<br />
<br />
'''HJL'''<br />
*Empresa de corte por Laser y otros servicios en Murcia.<br />
*[http://www.hjl.es/ HJL]<br />
*Teléfono:968 802 044<br />
<br />
{| class="wikitable"<br />
|-<br />
|<br />
[[File:Clone-Wars-logo.png|border|100px|link=Proyecto Clone Wars]]<br />
| [[Proyecto Clone Wars]]<br />
|}<br />
<br />
[[Category:Clone wars/es]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Clone_Wars:_Tiendas/es&diff=130934Clone Wars: Tiendas/es2014-08-06T09:40:22Z<p>Merlucin: /* On-line España */</p>
<hr />
<div>{{Languages|Clone_Wars:_Tiendas}} <br />
== Tiendas ==<br />
Sección donde se listan por orden alfabético las tiendas donde es posible encontrar componentes para tu impresora 3d:<br />
=== On-line España ===<br />
* [http://3dinvasion.com/ '''3Dinvasion'''] (España - Canarias) Venta de todos los componentes y filamento para impresoras 3D y talleres 3D. Envio 24h/48h a Canarias<br />
* [http://www.3dorobotics.com/tienda/ '''3DoRobotics'''] (España) Todo lo relacionado con la impresión 3D. Distribución de las mejores marcas. Servicio de impresión 3D bajo demanda.<br />
* [http://shop.createc3d.com '''Createc 3D shop''']: Lab y Makerspace en Granada con tienda física y online donde poder comprar cualquier cosa relacionada con la impresión 3D y tecnología Open Source. Cursos y talleres con formación continua. '''Nuestros clientes están 100% satisfechos con la calidad y servicio técnico que ofrecemos'''. Entra y compruébalo tu mismo [http://www.createc3d.com Createc 3D]<br />
* [http://filamentoabs.com/ FilamentoABS] (España). Envíos gratis a Madrid [filamento]<br />
* [http://formate21.es/impresoras-3d/ Formate 21] (España) Venta de todos los componentes para impresoras 3D. Talleres 3D por toda España.<br />
* [http://ifusionshop.com/index.php iFusionShop] Todo lo básico para tu impresora 3D en la tienda mas molona! ;). Servicio de impresión y prototipado en 3D. También puedes solicitar la recogida en mano si eres de Tarragona, llamándonos al teléfono de la web<br />
* [http://www.igus.es/default.asp Igus] (España) Tienda especializada en rodamientos lineales sin bolas, cadenas porta cables en sistemas plásticas de alto rendimiento y mesas con husillo.<br />
* [http://impresoras3dlowcost.com Impresoras3DLowCost.com] (España)(Andalucía) Tenemos todo lo que necesitas para montar tu impresora 3D a los mejores precios, con atención personalizada y respuesta en menos de 24 horas.<br />
* [http://www.imprimiendoen3d.es IMPRIMIENDO EN 3D] (España) Tienda online con todo lo necesario para construir tu impresora 3d. Rodamientos, motores, electronica, varillas, filamento. Prusa I3 369€ IVA incluido<br />
* [http://www.iniciativas3d.com/ '''Iniciativas3D''' ](España) Tu tienda de impresión 3D en Córdoba. '''Kits desde 340€''', '''ABS/PLA desde 17€''', descubre porque la '''mejor calidad''' y el '''mejor precio''' no tienen que estar reñidos. '''Sin costes de envío''' o recoge tu pedido en nuestra delegación en '''Córdoba''' o '''Málaga'''.<br />
* [http://www.kitprinter3d.com KITPRINTER3D ] '''Prusa i3 a 399 € (IVA incluido)''', '''P3Steel por 409 € (IVA incluido)''', ABS y PLA. Tienda física en el centro de Madrid.<br />
* [http://leapto3d.com/ LeapTo3D] (España) - Kits completos con TODO incluido. Recogida gratuita en Madrid. [filamento]<br />
* [http://www.lemonmaker.es/ LemonMaker] (España) Diseño & Impresión 3D. Kits impresoras 3D, workshops, componentes y filamento. Albacete, Madrid y Murcia. [CUALQUIER COSA ES POSIBLE].<br />
* [http://www.http://shop.menextech.com/index.php '''MENEXTECH'''] (España)'''Tienda renovada de Impresion 3d'''. Todo lo necesario para que construyas tu impresora y componentes informaticos. Una de las pioneras en impresion 3D en España. Visitanos y no te arrepentiras. '''Kit Prusa 390€.'''<br />
* [http://www.moebyus.com/ Moebyus Machines ](España) Sólo vendemos si tenemos stock. Entrega en 24h. Kits, marcos de metacrilato, filamento y todos los componentes necesarios para la prusa i3. Precios excelentes.<br />
* [http://printallthethings.com Print All the Things!!!] (España) Multitud de colores PLA/ABS del bueno en tu casa al día siguiente. También fabrican injectores jhead de gran calidad, y tienen camas calientes mk2b espectaculares.<br />
* [http://www.printeddreams.es Printed Dreams] (España) Servicio 360° sobre impresión 3D. ¡La mejor calidad al mejor precio! Kit impresora 3D, ABS/PLA 16,95 € (IVA inc) el kilo con '''+ de 18 colores diferentes'''. Y muchas otras cosas. info@printeddreams.es<br />
* [http://printhatshit.com PRINTHATSHIT - Easy 3D Printing -] (España) Tienda online y física en Barcelona. Todo lo que necesitas para montar tu Impresora 3D. Envío 24 horas y recogida en tienda.<br />
* [http://www.plabs3d.com PLABS 3D] (España) Gran servicio y calidad en todo tipo de materiales al mejor precio; PLA, ABS, HIPS, Nylon, Laywood, Laybrick, PVA, TPE, PS, Poikilothermal, Conductivo, Glow in the dark, etc!! mail: plabs3d@gmail.com.<br />
* [http://www.rationalstock.es/ Rational Stock] (España) Ferretería online. Variedad y buenos precios para tornillería. Permite comprar por unidades. Envío económico en 24-48 horas.<br />
* [http://www.thingibox.com/ ThingiBOX] (España) Componentes y filamentos para impresoras 3D y otros proyectos opensource.<br />
* [http://wi3dprint.com/ '''wi3Dprint'''] (España) '''KIT PRUSA i3 HEPHESTOS: 449 Euros IVA Incl.''' Venta impresoras 3D, talleres, componentes y filamentos. Servicio de impresión<br />
<br />
=== On-line ===<br />
Europa:<br />
* [http://www.mendel-parts.com/ Mendel parts] (Holanda)<br />
* [http://www.xyzprinters.com/ http://www.xyzprinters.com/] (Holanda)<br />
* [http://shop.arcol.hu/ arcol.hu] (Hungría) <br />
* [https://shop.grrf.de/ German RepRap fundation] (Alemania)<br />
* [http://reprapsource.com/ reprapsource.com]<br />
* [http://reprapworld.com/ Reprap world] (Holanda) [filamento]<br />
* [https://0xfb.com/shop.html Future Bits] La tienda de Kliment! (Alemania)<br />
* [http://www.hotends.com/ hotends]<br />
* [http://www.orbi-tech.de/index_english.htm Orbi-tech]. Plástico (Alemania)<br />
* [http://reprap-3d-printer.com/ Reprap-3D-printer] (Francia)<br />
<br />
EEUU / América (ojo aduanas)<br />
* [http://www.makergear.com/ Makergear] (EEUU)<br />
* [http://www.lulzbot.com/en/ Lulzbot] (EEUU)<br />
* [http://gala-automation.com/ Gala automation] (EEUU)<br />
* [http://techpaladin.com/ techpaladin] (EEUU)<br />
* [http://www.centralreprap.com/prestashop/ CentralReprap]<br />
* [http://ultimachine.com/ Ultimachine] (EEUU)<br />
* [http://www.makermex.com/ MakerMex] (México)<br />
<br />
Otros <br />
* [http://www.3dacessorieshub.com/ 3D Acessories Hub ].Una ventanilla única para todos los componentes de RepRap y las impresoras 3D<br />
* [http://www.goodluckbuy.com/ http://www.goodluckbuy.com/]. Tienda en china donde venden motores, varillas roscadas...<br />
* [http://www.futurlec.com/ Futurlec] Electrónica en general<br />
* [http://www.taydaelectronics.com/ Tayda Electronics] Electrónica en general<br />
* [http://www.dealextreme.com/ Dealextreme] Tienda china con prácticamente cualquier cosa. (contrasta precios antes de comprar)<br />
* [http://www.bitsbox.co.uk/ BitsBox] Componentes electrónicos, algunos especialmente baratos. Envía por ~3€<br />
* [http://www.emakershop.com/ eMAKERshop] Tienda online que vende productos de varios vendedores externos, como un portal de venta.<br />
* [http://www.zappautomation.co.uk/index.php?language=ES Zappautomation] Tienda con todo tipo de productos para CNCs (UK)<br />
* [http://makemendel.com/ Makemendel]<br />
* [http://www.ebay.com/itm/1pc-200mm-X-100ft-High-Temperature-Resistant-Kapton-Tape-/170864710486?ssPageName=ADME:L:OU:ES:3160 Kapton en eBay]: Cinta kapton de 20cm de ancho<br />
* [http://www.reprap.cc/ Reprap Austria] Tienda de todo tipo de material para Reprap tambien en ebay: [http://www.ebay.es/sch/reprapper/m.html?_nkw=&_armrs=1&_from=&_ipg=&_trksid=p3686 reprapper]<br />
<br />
=== Físicas ===<br />
* [[Clone_wars:_Tiendas_en_Andalucia|Andalucía]]<br />
* [[Clone_wars:_Tiendas_en_asturias|Asturias]]<br />
* [[Clone_wars:_Tiendas_en_castellon|Castellón]]<br />
* [[Clone_wars:_Tiendas_en_galicia|Galicia]]<br />
* [[Clone_wars:_Tiendas_en_barcelona|Barcelona]]<br />
* [[Clone_wars:_Tiendas_en_madrid|Madrid]]<br />
* [[Clone_wars:_Tiendas_en_navarra|Navarra]]<br />
* [[Clone_wars:_Tiendas_en_valencia|Valencia]]<br />
* [[Clone_wars:_Tiendas_en_zaragoza|Zaragoza]]<br />
[http://goo.gl/maps/Md32Y Mapa] de tiendas y talleres<br />
<br />
=== Lista negra de tiendas ===<br />
Tiendas con las que hemos tenido malas experiencias:<br />
* [http://myworld.ebay.es/drumas09/ drumas09] (UK). Este vendedor no envía los pedidos. Pedro tuvo un problema con este vendedor.<br />
<br />
== Servicios de Corte ==<br />
<br />
'''Cortenfrio'''<br />
*Empresa de corte en frio ubicada en Zaragoza.<br />
*[http://cortenfrio.com/index.htm Cortenfrio]<br />
<br />
'''Laserebro'''<br />
*Son un grupo de empresas con muchas sedes, tienes una cerca de casa seguro :D mira en el mapa de localizacion, en su web, en el apartado: Grupo Láser Ebro.<br />
*[http://www.laserebro.com/frame1.htm Laserebro]<br />
<br />
'''Naivan'''<br />
*Empresa de corte por Laser y otros servicios en Vitoria.<br />
*[http://www.naivan.com/ Naivan]<br />
*Email para enviar los planos de corte: naivan@naivan.com (enviar en dxf o pdf acotado)<br />
*Teléfono:945 259 857<br />
<br />
'''HJL'''<br />
*Empresa de corte por Laser y otros servicios en Murcia.<br />
*[http://www.hjl.es/ HJL]<br />
*Teléfono:968 802 044<br />
<br />
{| class="wikitable"<br />
|-<br />
|<br />
[[File:Clone-Wars-logo.png|border|100px|link=Proyecto Clone Wars]]<br />
| [[Proyecto Clone Wars]]<br />
|}<br />
<br />
[[Category:Clone wars/es]]</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Belts_and_Pulleys&diff=124685Belts and Pulleys2014-05-02T08:49:34Z<p>Merlucin: /* Pulleys */</p>
<hr />
<div>{{Merge|GT2_Timing_Belt}}<br />
[[Category:Suppliers_by_Part]]<br />
<br />
See also [[Choosing_Belts_and_Pulleys]]<br />
<br />
==Belts==<br />
<br />
See also [[GT2 Timing Belt]]<br />
<br />
{| class="wikitable sortable"<br />
|+ <br />
|- style="background-color:#f0f0f0;"<br />
! Supplier !! From !! Type available !! Pitch !! Width !! Length !! Material !! Additional notes <br />
|-<br />
| [http://www.3distributed.com/collections/frontpage/products/gt2-timing-belt 3Distributed] || UK || GT2 || 2mm || 6mm || Sold by the metre || Fiberglass reinforced neoprene rubber. || Delivers Worldwide <br />
|-<br />
| [http://www.think3dprint3d.com/Hardware Think3DPrint3D] || UK || GT2, T2.5 || 2 mm, 2.5 mm || 6 mm || sold by the meter || fiberglass reinforced rubber, steel-reinforced polyurethane|| fast world-wide delivery and excellent customer service<br />
|-<br />
|[http://3dacessorieshub.com/ 3D Acessories Hub] || India || GT2 <BR> T2.5 || 2 mm <BR> 2 mm || 660mm closed <BR> as per your requirement || || Rubber <BR> <br />
polyurethane || -<br />
|-<br />
|[http://3dprinterczar.com/shop/hardware/gt2-pulley-belt/ 3D Printer Czar] || US || GT2 || 2 mm || 6 mm || at your choice|| Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://www.robotdigg.com/category/9/Timing-Pulley&Belt 3DCracker] || CN ||[http://www.robotdigg.com/category/9/Timing-Pulley&Belt GT2] || 2 mm || 6 mm || 900mm, 976mm, 1220mm, 1350mm|New-add '''1524mm closed-loop''', etc and open ended || Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://www.reprap.cn/ He3D] || CN || GT2, MXL, T2.5, T5 || 2.5 mm || 6 mm || 1350mm 990mm and open ended || Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://reprapuniverse.com/catalog/product_info.php?cPath=30_73&products_id=67 ReprapUniverse.com] || Netherlands || T2.5 || 2.5 mm || 5 mm || sold by the meter || Open ended Neoprene Rubber with Fiberglass Reinforced|| Perfect timing belt for Prusa Mendel i2, Prusa i3, MendelMax 1.5. Cheap International Shipping.<br />
|-<br />
| [http://www.3dmakerworld.com 3DMakerWorld] || US || GT2 || 2 mm || 6 mm || 1164 mm || Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://www.charlies3dtechnologies.eu/Belts_and_Pulleys/cat1675912_1594189.aspx Charlie's 3D Technologies] || Belgium || MXL and GT2 || - || - || - || - || -<br />
|-<br />
| [http://www.cubic-print.com Cubic Print] || Germany || T2.5 <BR> T5 || 2.5 mm <BR> 5 mm|| 6 mm || as you wish || PU + steel || open belts<br />
|-<br />
| [http://www.bbman.com/ BBMan] || US || Imperial/Metric<br />
|-<br />
| [http://www.beltingonline.com/ Belting Online] || UK || GT2, MXL, T2.5, T5 || 2 mm 2.5 & 5mm|| As you wish || As you wish|| PU & Neoprene Rubber || Genuine Branded Quality Products <br />
|-<br />
<br />
| [http://easyreprap.com/shop/article_19/GT2-Belt-_-Pulley-Set.html Easy RepRap] || USA ||Precision GT2 || 2 mm || 6 mm || 1150mm || Fiberglass Reinforced || GT2 Belt/Pulley Sets<br />
|-<br />
<br />
| [http://www.ebay.com/sch/yellowvirtualsales/m.html eBay: Yellowvirtualsales] || USA ||Precision GT2 || 2 mm || 6 mm || Cut To Length || Fiberglass Reinforced || Fast Worldwide Shipping<br />
|-<br />
| [http://www.econobelt.com/Timing_Belts.htm Econobelt] || US || many<br />
|-<br />
| [http://www.timing-belt-manufacturer.com/contact.html Eke] || China || many<br />
|-<br />
| [http://www.indiamart.com/bm-beltings-company/industrial-belts.html#open-end-polyurethane Indiamart] || India || many<br />
|-<br />
| [https://www.inventables.com/categories/frame-rail/belting Inventables] || US|| MXL || - || - || 1 foot increments || - || -<br />
|-<br />
| [http://www.kainabelt.com KainaBelt] || China || many<br />
|-<br />
| [http://makemendel.com/mechanical-parts/t2-5-timing-belt Makemendel] || India || GT2 <BR> T2.5 || 2mm <BR> 2.5 mm || 7 mm <BR> 7mm || Open Belt || PU || Open Belts for all Reprap and other 3D printers. Available in custom length.<br />
|-<br />
| [http://www.megadyne.it/ Megadyne] || Italy || many<br />
|-<br />
| [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1175 Misumi] || multiple<br />
|-<br />
| [http://www.paoparts.com/fr/15-courroies Paoparts] || France || T2.5 <br> T5 || 2,5mm <br> 5mm || 5mm || - || PU ||<br />
|-<br />
| [http://shop.polybelt.com/Metirc-Pitch-Open-End-Belt-Roll_c29.htm PolyBelt] || US || T2.5 <br> T5 || 5 mm || 6 mm || - || polyurethane + steel || -<br />
|-<br />
| [http://reprapworld.com/?searchresults&cPath=1595_1611 RepRapWorld] || Netherlands || T2.5 <br> T5 || 2,5 mm <br> 5 mm || 5 mm <br> 5 mm || 1 m || neoprene<br>polyurethane + steel || -<br />
|-<br />
| [http://www.robotdigg.com RobotDigg] || China || [http://www.robotdigg.com/product/10/Open-Ended-6mm-Width-GT2-Belt GT2], MXL, T2.5 || 2 mm || 6mm, 6.35mm or 9mm || 20M or 50M per roll ,[http://www.robotdigg.com/product/38/Closed-loop-GT2-Belt,-101-Teeth-202mm-Long Closed-loop GT2]|| Neoprene Rubber, Fiberglass Reinforced. MOQ 50M<br />
|<br />
|-<br />
| [http://www.royalsupply.com/store/pc/Gates-2MR-1164-06-PowerGrip-GT2-V-Belt-2MR-and-3MR-93901582-1036p17193.htm Royal supply] || US || GT2 || 2 mm || 6 mm || 1164 mm || fiberglass / nylon / neoprene || -<br />
|-<br />
| [https://sdp-si.com SDP-SI] || US || Imperial/Metric<br />
|-<br />
| [http://techpaladin.com/store/#ecwid:category=1941327&mode=product&product=9001827 TechPaladin] || US || GT2 || 2 mm || 5 mm || 1160 mm || neoprene || -<br />
|-<br />
| [http://www.tanals.com/fr/courroies-dentees-neoprene/ Tanals] || France || many || - || - || - || - || don't sell to individuals<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || Spain || GT2 || 2mm || 5 or 6 mm || Sold by the meter, open ended || Neoprene Rubber || Worldwide shipping<br />
|-<br />
| [http://www.tridprinting.com/Mechanical-Parts/ TriDPrinting.com] || US || GT2 || 2 mm || 6 mm || Sold by the meter, open ended || Neoprene, Fiberglass Reinforced || 50 m max, Worldwide Delivery<br />
|-<br />
| [http://www.RepRap-India.com RepRap-India.com] || IN || GT2 || 2 mm || 6 mm || open ended || Neoprene, fiberglass reinforced || 50 m max<br />
|-<br />
|}<br />
<br />
<br />
<br />
{| class="wikitable sortable"<br />
|- style="background-color:#f0f0f0;"<br />
! Vendor !! Loc. !! Product !! Width !! Pitch !! Length !! class="unsortable" | Additional notes<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/collections/frontpage/products/gt2-timing-belt GT2 Belt] || 6mm || 2.00mm || Multiples of 1000mm || &nbsp;<br />
|-<br />
| Think3DPrint3D || UK || [http://www.think3dprint3d.com/Hardware/GT2-Timing-Belt GT2 Belt] || 6 mm || 2.00 mm || multiples of 1000 mm || &nbsp;<br />
|-<br />
| 3D Acessories Hub || IN|| [http://www.3dacessorieshub.com GT2 Belt] || 7 mm || 2.00 mm || 660 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ 3DCracker&RobotDigg]|| CN || [http://www.robotdigg.com/product/160/1524mm-long-762-teeth-closed-loop-gt2-belt-for-rostock 1524mm Endless GT2 Belt] || 6 mm || 2.00 mm || 1524 mm || &nbsp;<br />
|-<br />
| 3DCracker || CN || [http://www.3dcracker.com GT2 Belt] || 6 mm || 2.00 mm || Open ended and closed-loop || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/xy-gt2-timing-belt-pulley-kit-1 Prusa Kit] || 6 mm || 2.00 mm || 1000 mm || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/d-gt2-timing-belt-pulley-kit Rostock/Delta Kit] || 6 mm || 2.00 mm || 1000 mm || &nbsp;<br />
|-<br />
| 3DMakerWorld || US || [http://www.3dmakerworld.com/store/parts-accessories/hardware/gt2-timing-belt Belt] || 6 mm || 2.00 mm || 1164 mm || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_belts Belt] || 3 mm || 2.00 mm || 54-1910 mm || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_belts Belt] || 6 mm || 2.00 mm || 54-1910 mm || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_belts Belt] || 9 mm || 2.00 mm || 54-1910 mm || &nbsp;<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-900mm-x-6mm-450-teeth-11958 Separate Belt at 900mm length] || 6&nbsp;mm || 2.00 mm || 900 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-976mm-x-6mm-488-teeth-11959 Separate Belt at 976mm length] || 6&nbsp;mm || 2.00 mm || 976 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1032mm-x-6mm-516-teeth-12179 Separate Belt at 1032mm length] || 6&nbsp;mm || 2.00 mm || 1032 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1164mm-x-6mm-582-teeth-11960 Separate Belt at 1164mm length] || 6&nbsp;mm || 2.00 mm || 1164 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1386mm-x-6mm-693-teeth-12181 Separate Belt at 1386mm length] || 6&nbsp;mm || 2.00 mm || 1386 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1524mm-x-6mm-762-teeth-12180 Separate Belt at 1524mm length] || 6&nbsp;mm || 2.00 mm || 1524 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/universal-gt2-belts-pulleys-kit-for-reprap-other-3d-printers-11954 Universal Kit for RepRap/Other 3D Printers] || 6 mm || 2.00 mm || 1032 & 1164 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-reprap-prusa-11950 Kit for RepRap Prusa] || 6 mm || 2.00 mm || 900 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-delta-robot-11953 Kit for Rostock Delta Robot] || 6 mm || 2.00 mm || 1524 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-mini-11952 Kit for Rostock Mini] || 6&nbsp;mm || 2.00 mm || 1032 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Charlie's 3D Technologies || BE || [http://www.charlies3dtechnologies.eu/GT2_Belt_1_m/p1675911_9494987.aspx Belt] || 6 mm || 2.03 mm || 1000 mm || &nbsp;<br />
|-<br />
| Cubic-Print || DE || [http://www.cubic-print.de GT2 Belt kit] || 6 mm || 2.00 mm || cut to length || &nbsp;<br />
|-<br />
| eBay: fabster3d || CN || [http://www.ebay.com/sch/fabster3d/m.html Belt] || 6 mm || &nbsp; || 974-1164 mm || &nbsp;<br />
|-<br />
| eBay: yellowvirtualsales || US || [http://www.ebay.com/sch/yellowvirtualsales/m.html Precision GT2 Belt] || 6 mm || 2.00 mm || Cut To Length || &nbsp;<br />
|-<br />
| EmotionTech || FR || [http://www.reprap-france.com/68-kit-de-courroies-gt2.html Belt] || 6 mm || 2.00 mm || 850 mm || &nbsp;<br />
|-<br />
| Fabberworld || CH || [http://www.fabberworld.com/Pulleys-and-Timing-Belts/GT2-Timing-Belt-by-the-meter::39.html Belt] || 6 mm || 2.00 mm || 1000+ mm || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=74 Kit for RepRap Prusa 2] || 6 mm || &nbsp; || 976 mm x 3 || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=75 Kit for Rostock Mini] || 6 mm || &nbsp; || 900 mm x 3 || &nbsp;<br />
|-<br />
| Makemendel || IN|| [http://makemendel.com/mechanical-parts/mechanical-parts-1/pulleys-and-belts/gt2-open-belt GT2 Belt] || 7 mm || 2.00 mm || 1000 mm and more || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302190510/ 2GT Belt] || 4 mm || 2.00 mm || 662-9942 mm || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302190510/ 2GT Belt] || 6 mm || 2.00 mm || 662-9942 mm || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302190510/ 2GT Belt] || 9 mm || 2.00 mm || 662-9942 mm || &nbsp;<br />
|-<br />
| ReprapWorld.com || EU || [http://reprapworld.com/?searchresults&cPath=1655] || 6 mm || 2.00 mm || 1000-75000 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/38/Closed-loop-GT2-Belt,-101-Teeth-202mm-Long 202mm Closed-loop GT2 Belt] || 6 mm || 2.00 mm || 202 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/48/760mm-380-teeth-Closed-loop-6mm-Width-GT2-Belt 760mm Closed-loop GT2 Belt] || 6 mm || 2.00 mm || 760 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/160/1524mm-long-762-teeth-closed-loop-gt2-belt-for-rostock 1524mm Endless GT2 Belt] || 6 mm || 2.00 mm || 1524 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/10/Open-Ended-6mm-Width-GT2-Belt GT2 Belt Open Ended] || 6 mm || 2.00 mm || 1000-50000 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/22/MXL-Belt,-6mm-Width-Open-Ended MXL Belt] || 6 mm || 2.00 mm || 1000-50000 mm || &nbsp;<br />
|-<br />
| RoyalSupply || US || [http://www.royalsupply.com/store/pc/Gates-2MR-1164-06-PowerGrip-GT2-V-Belt-2MR-and-3MR-93901582-1036p17193.htm#details Belt] || 6 mm || 2.00 mm || 1164 mm || &nbsp;<br />
|-<br />
| TechPaladin Printing || US || [http://techpaladin.com/store/#!/~/product/id=9001827 Belt] || 6 mm || 2.00 mm || 1380 mm || &nbsp;<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || ES || [http://store.thingibox.com/en/powertransmission/7-gt2_timing_belt.html GT2 Belt] || 5 or 6 mm || 2.00 mm || Multiples of 1m || Worldwide shipping<br />
|-<br />
|[http://www.TriDPrinting.com/ TriDPrinting.com]|| US || [http://www.TriDPrinting.com/Mechanical-Parts/ GT2 Belt Open Ended] || 6 mm || 2.00 mm || 1000-50000 mm || Worldwide Delivery;<br />
|-<br />
| Ultibots || US || [http://www.ultibots.com/gt2-timing-belt-1164mm/ Belt] || 6 mm || 2.00 mm || 1164 mm || &nbsp;<br />
|}<br />
<br />
<br />
<br />
There is also some on ebay.<br />
<br />
*beside GT2 belts, there is also 2M that have a 2mm round pitch (like [http://www.powerdrive-belt.com/new/products.asp?x=1&id=16&id2=69&id4=2&t=1] and many other suppliers)<br />
<br />
==Pulleys==<br />
<br />
See also [[GT2 Timing Belt]].<br />
<br />
{| class="wikitable sortable"<br />
|+ <br />
|- style="background-color:#f0f0f0;"<br />
! Supplier !! From !! Type available !! Pitch !! Tooth !! Size (bore, OD,...) !! Max belt width !! Material !! Additional notes <br />
|-<br />
| [http://www.3distributed.com/products/gt2-pulley 3Distributed] || UK || GT2 || 2mm || 20 || 5mm || 6mm || Aluminium with grub screws || Delivers Worldwide<br />
|-<br />
| [http://www.think3dprint3d.com/Hardware/t2.5-16-ToothTimingPulley-M4GrubScrews Think3DPrint3D] || UK || T2.5 || 2.5 mm || 16 || 5 mm || 7 mm || Aluminum with zinc plated steel flanges|| fast delivery and excellent customer service!<br />
|-<br />
| [http://www.robotdigg.com/category/9/Timing-Pulley&Belt 3DCracker&RobotDigg] || CN || GT2 || 2 mm || 16, 20, 36 || 5 mm or 8mm || 7 mm || All Aluminum || -<br />
|-<br />
| [http://www.3dmakerworld.com 3DMakerWorld] || US || GT2 || 2 mm || 20 & 36 || 5 mm || 6 mm || Aluminium & Polycarbonate with brass insert || -<br />
|-<br />
| [http://reprapuniverse.com/catalog/product_info.php?products_id=68 ReprapUniverse.com] || Netherlands || T2.5 || 2.5mm || 16 || 5 mm || 6 mm || Aluminum + M3 grub screws || Quality Aluminum Pulleys. Perfect for Reprap 3D Printers: Prusa Mendel i2, Prusa i3, MendelMax 1.5 & others. Cheap International Shipping.<br />
|-<br />
| [http://www.charlies3dtechnologies.eu/Belts_and_Pulleys/cat1675912_1594189.aspx Charlie's 3D Technologies] || Belgium || MXL and GT2 || - || 15 or 20 || -|| - || - || -<br />
|-<br />
| [http://www.cubic-print.com Cubic Print] || Germany || T2.5 <BR> T5 || 2.5mm <BR> 5 mm || 8, 16 || 5 mm || 7 mm || alu + steel grub screws || -<br />
|-<br />
| [http://www.bbman.com/ BBMan] || US || many<br />
|-<br />
| [http://www.beltingonline.com/timing-pulleys-272/ Belting Online] || UK || GT2, T2.5, T5 & MXL || 2mm, 2.5mm, 2.03mm & 5mm ||16, 18, 20, 36 <BR> Also Special Made to order if required || 5mm <BR> Specials sizes are possible. || 6mm || Alu + Grub Screws || Quality Pulleys Manufactured in the UK. <br />
|-<br />
| [http://www.econobelt.com/e-store/Pulleys.htm Econobelt] || US || many<br />
|-<br />
| [http://www.ebay.com/sch/m.html?_odkw=&item=181168182751&pt=BI_Heavy_Equipment_Parts&_osacat=0&hash=item2a2e7715df&_ssn=yellowvirtualsales&_trksid=p2046732.m570.l1313&_nkw=pulley&_sacat=0&_from=R40 eBay: Yellowvirtualsales] || USA || GT2, HDT3M || 2MM / 3MM|| 12-36 || 5 mm || 6-10MM mm || Fiberglass Reinforced || Fast Worldwide Shipping<br />
|-<br />
| [https://www.inventables.com/categories/frame-rail/pulleys Inventables] || US|| MXL || - || - || - || - || - || - <br />
|-<br />
| [http://makemendel.com/mechanical-parts/t2-5-pulley MakeMendel] || India || GT2 <BR> T2.5 || 2 <BR> 2.5 mm || 20 <BR> 12 or 16 || 5 mm || 7mm || Aluminium with grub screws || T2.5 pulley is available in 12 teeth and 16 teeth as well. Suitable for all 3D printers. Shipping is worldwide<br />
|-<br />
| [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1097 Misumi] || multiple<br />
|-<br />
| [http://www.paoparts.com/fr/15-courroies Paoparts] || France || T2,5 <br> T5<br />
|-<br />
| [http://reprapworld.com/?products_details&products_id=247 RepRapWorld] || Netherlands || T5 || 5 mm || 8 || 5 mm x 17 mm x 20 mm || ? || Alu || Pulley profile has play resulting in lash when reversing<br />
|-|-<br />
| [http://www.robotdigg.com/ RobotDigg] || China || [http://www.robotdigg.com/category/9/Timing-Pulley&Belt GT2], T2.5 and MXL || 2mm, 2.5mm, 2.03mm || 16, 18, 20, 36 || 5*17.5*18 mm || 7mm || Alu || SKYPE: robotdigg<br />
|-<br />
| [http://www.royalsupply.com/store/pc/Gates-2MR-18S-06-PowerGrip-GT2-Sprockets-2MR-and-3MR-78426007-1555p42023.htm#details Royal Supply] || US || GT2 || 2 mm || 18 || 4,7 mm || 6 mm || Alu || you'll need to redrill the bore (3/16") to fit usual 5 mm motor shaft<br />
|-<br />
| [https://sdp-si.com SDP-SI] || US || many<br />
|-<br />
| [http://techpaladin.com/store/#ecwid:category=1941327&mode=product&product=9188440 TechPaladin] || US || GT2 || 2 mm || 36 || 5 mm || 6 mm || plastic/bronze || -<br />
|-<br />
| [http://www.TriDPrinting.com/Mechanical-Parts/ TriDPrinting.com] || US || GT2 || 2 mm || 16, 20 || 5 mm || 6 mm || Aluminium with grub screws || Uses two set screws, Worldwide Delivery<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || Spain || GT2 || 2 mm || 16, 20 || 5 mm || 4-6 mm || Aluminium + grub screws || Worldwide shipping<br />
|-<br />
| [http://ultimachine.com/content/timing-pulley-gt2-20-tooth Ultimachine] || US || GT2 || 2 mm || 20 || 5 mm || 6 mm || Alu || use two set screws<br />
|-<br />
| [http://RepRap-India.com RepRap-India.com] || US || GT2 || 2 mm || 20 || 5 mm || 6 mm || Alu || use two set screws<br />
|-<br />
| [http://RepRap-India.com RepRap-India.com] || US || T2.5 || 2 mm || 20 || 5 mm || 6 mm || Alu || use two set screws<br />
|-<br />
<br />
|}<br />
<br />
<br />
<br />
{| class="wikitable sortable"<br />
|- style="background-color:#f0f0f0;"<br />
! Vendor !! Loc. !! Product !! Material !! Belt width !! Bore !! Tooth !! Flange !! class="unsortable" | Additional notes<br />
|-<br />
| 3D Acessories Hub || IN || [http://www.3dacessorieshub.com GT2 Pulley] || Aluminium || 7 mm || 5.00 mm || 20 || - || &nbsp;<br />
|-<br />
| 3DCracker || CN || [http://www.3dcracker.com GT2 Pulley] || &nbsp; || 7 mm || 5, 8mm || 16, 20, 36 || double || &nbsp;<br />
|-<br />
| eBay: Yellowvirtualsales|| US || [http://www.ebay.com/sch/m.html?_odkw=gt2&_osacat=0&_from=R40&_ssn=yellowvirtualsales&_trksid=p2046732.m570.l1313.TR11.TRC1.A0.Xpulley.TRS0&_nkw=pulley&_sacat=0 Timing Pulleys] || Aluminum, Metal || 6mm - 10mm || 5.00 mm || 12-36 || Vary || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/collections/frontpage/products/gt2-pulley Pulley] || &nbsp; || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/xy-gt2-timing-belt-pulley-kit-1 Prusa Kit] || &nbsp; || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/d-gt2-timing-belt-pulley-kit Rostock/Delta Kit] || &nbsp; || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| 3DMakerWorld || US || [http://www.3dmakerworld.com/store/parts-accessories/hardware GT2 Timing Pulley] || Aluminium & Polycarbonate with brass insert || 6 mm || 5.00 mm || 20 & 36 || double || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_pulley Pulley] || Aluminium || 3 mm || 5.00 mm || 12-20 || double || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_pulley Pulley] || Aluminium || 6 mm || 5.00 mm || 12-20 || double || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_pulley Pulley] || Aluminium || 9 mm || 5.00 mm || 12-20 || double || &nbsp;<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-pitch-pulley-20-tooth-c-w-5mm-h7-bore-2-x-m3-g-s-11970 Separate Timing Pulley (sold each)] || Aluminium || 6 mm || 5.00 mm || 20 || double || UK Manufactured Precision Pulley<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/universal-gt2-belts-pulleys-kit-for-reprap-other-3d-printers-11954 Universal Kit for RepRap/Other 3D Printers] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-reprap-prusa-11950 Kit for RepRap Prusa] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-delta-robot-11953 Kit for Rostock Delta Robot] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-mini-11952 Kit for Rostock Mini] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Charlie's 3D Technologies || BE || [http://www.charlies3dtechnologies.eu/GT2_Pulley_Deluxe_1_pcs/p1675911_9495003.aspx Pulley] || Aluminium, nylon || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Charlie's 3D Technologies || BE || [http://www.charlies3dtechnologies.eu/GT2_Alu_Pulley_Deluxe_1_pcs/p1675911_9652574.aspx Pulley] || Aluminium || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Cubic-Print || DE || [http://www.cubic-print.com Pulley / Kit] || Aluminium || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| eBay: fabster3d || CN || [http://www.ebay.com/sch/fabster3d/m.html Pulley] || Aluminium (black) || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| EmotionTech || FR || [http://www.reprap-france.com/69-poulie-gt2.html Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Fabberworld || CH || [http://www.fabberworld.com/Pulleys-and-Timing-Belts/GT2-Pulley-20-Tooth-Aluminium::40.html Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=74 Kit for RepRap Prusa 2] || Aluminium (black) || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=75 Kit for Rostock Mini] || Aluminium (black) || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Makemendel || IN || [http://makemendel.com/mechanical-parts/mechanical-parts-1/gt2-pulley GT2 Pulley] || Aluminium || 7 mm || 5.00 mm || 20 || - || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302193470/ 2GT Pulley] || Aluminium || 4 mm || 5.00 mm || 32 || double || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302193470/ 2GT Pulley] || Aluminium || 6 mm || 5.00 mm || 32 || double || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302193470/ 2GT Pulley] || Aluminium || 9 mm || 5.00 mm || 32 || double || &nbsp;<br />
|-<br />
| Misumi || Japan || [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=metric2010&page=1095 Misumi's pulley introduction] || ? || ? || ? || ? || ?<br />
|<br />
Another good source for GT2 pulleys and belts is Misumi. They carry a huge variety of suitable pulleys, including several that are closer to out ideal diameter. In addition, Misumi has offices around the globe so they are a better choice for international customers (though some regions will only sell to businesses).<br />
<br />
Their website does not make it easy to browse for belts and pulleys, but here are the relevent pages in their catalog:<br />
<br />
* [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1097 Pulleys]<br />
* [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1175 Belts]<br />
* [http://www.sdp-si.com/D265/HTML/D265T003.html Handbook of Timing Belts and Pulleys]<br />
<br />
Note: Misumi calls theirs 2GT (2mm pitch) and 3GT (3mm pitch). As far as I know they are compatible with GT2, but both offer the same benefits. Misumi's pulleys seem expensive, but they are metal pulleys. We don't really need metal pulleys for our needs, but they are fine.<br />
<br />
<br />
|-<br />
| ReprapWorld.com || EU || [http://reprapworld.com/?searchresults&cPath=1655 Multiple types of Pulley] || Aluminium || 5-6 mm || 5mm || Multiple || double || &nbsp;<br />
|-<br />
| [http://www.robotdigg.com/ Robotdigg] || CN || [http://www.robotdigg.com/product/59/Rostock-16-Teeth-5mm-Bore-GT2-Pulley 16Teeth 2GT Pulley] || Aluminium || 7 mm || 5mm, 8mm || 16 || double || &nbsp;<br />
|-<br />
| [http://www.robotdigg.com/ Robotdigg] || CN || [http://www.robotdigg.com/product/9/GT2-Pulley-20-Teeth-5mm-Bore GT2 Pulley] || Aluminium || 7 mm || 5mm, 8mm || 20 || double || &nbsp;<br />
|-<br />
| [http://www.robotdigg.com/ Robotdigg] || CN || [http://www.robotdigg.com/product/24/GT2-Pulley-36-Teeth-5mm-Bore GT2 Pulley] || Aluminium || 7 mm || 5mm || 36 || double || &nbsp;<br />
|-<br />
| RoyalSupply || US || [http://www.royalsupply.com/store/pc/Gates-2MR-18S-06-PowerGrip-GT2-Sprockets-2MR-and-3MR-78426007-1555p42023.htm#details Pulley] || Aluminium || 4-6 mm || 4.76 mm || 18 || double || You'll need to redrill them to fit on the usual 5mm motor shaft<br />
|-<br />
| Stock Drive Products || US || https://sdp-si.com/ || &nbsp; || &nbsp; || 5.00 mm || [https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=22736&GroupID=347 36], [https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=8545&GroupID=347 40], [https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=55836&GroupID=347 42] || &nbsp;<br />
| In the US, a popular source is SDP/SI. They sell a huge variety of belts and pulleys that meet our needs. Always call SDP/SI for stock, their website is always out of date.<br />
<br />
* [https://sdp-si.com/eStore/Direct.asp?GroupID=347 Pulleys (bad link)]<br />Filter for GT2, 2mm pitch, then choose the bore size needed for your steppers.<br />
* [https://sdp-si.com/eStore/Direct.asp?GroupID=342 Belts (bad link)]<br />Filter on GT2, 2mm Pitch, and get 2 belts as close to 1m long as possible.<br />
<br />
Note, unfortunately, SDP/SI does not carry a smaller diameter GT2 pulley with a 5mm bore, so to buy your pulleys here you need a larger pulley than in strictly ideal. These are fine, though. I ([[User:Virtlink|Virtlink]] ?) use the 36 tooth pulleys on my printer and they work great.<br />
|-<br />
| TechPaladin Printing || US || [http://techpaladin.com/store/#!/~/product/category=1941327&id=18833859 Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || ES || [http://store.thingibox.com/en/powertransmission/8-pulleys.html GT2 Pulley] || Aluminium || 4-6 mm || 5.00 mm || 16 || double || Length: 7mm; Worldwide shipping<br />
|-<br />
| [http://www.TriDPrinting.com/ TriDPrinting.com] || US || [http://www.TriDPrinting.com/Mechanical-Parts/ GT2 Pulley] || Aluminium || 6 mm || 5.00 mm || 16, 20 || double || Worldwide Delivery<br />
|-<br />
| Ultibots || US || [http://www.ultibots.com/gt2-timing-pulley-20-tooth/ Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| UltiMachine || US || [https://ultimachine.com/content/timing-pulley-gt2-20-tooth Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|}<br />
<br />
=== RobotDigg ===<br />
China manufacturer of T2.5 pulley, MXL pulley, GT2 pulleys. T2.5 belt, MXL belt and GT2 belt in different width, open ended and endless or closed-loop timing belt provider.<br />
T2.5 pulley 16 tooth 5mm bore<br />
T5 pulley 12 tooth 8mm bore<br />
MXL pulley 18 teeth 5mm bore<br />
MXL pulley 20 teeth 6.35mm bore<br />
MXL pulley 36 teeth 5mm bore<br />
MXL pulley 36 teeth 8mm bore<br />
GT2 pulley 16 teeth 5mm bore<br />
GT2 pulley 18 tooth 6.35mm bore<br />
GT2 pulley 20 teeth 5mm, 6.35mm bore and 8mm bore<br />
GT2 pulley 32 tooth 10mm bore<br />
GT2 pulley 36 teeth 5mm bore and 8mm bore<br />
GT2 pulley 40 tooth 5mm, 6.35mm 8mm bore n 10mm bore<br />
* [http://www.robotdigg.com/product/25/T2.5-pulley,-16-teeth,-5mm-bore T2.5 pulley, 16 tooth, 5mm bore]<br />
* [http://www.robotdigg.com/product/26/MXL-pulley,-18-tooth,-5mm-bore MXL pulley 18 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/147/36-Tooth-MXL-Pulley-with-5mm-Bore MXL pulley 36 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/148/36-Tooth-MXL-Pulley-with-8mm-Bore MXL pulley 36 teeth, 8mm bore]<br />
* [http://www.robotdigg.com/product/59/Rostock-16-Teeth-5mm-Bore-GT2-Pulley 2GT pulley 16 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/9/GT2-Pulley-20-Teeth-5mm-Bore 2GT pulley 20 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/23/GT2-Pulley-20-Teeth-8mm-Bore 2GT pulley 20 teeth, 8mm bore]<br />
* [http://www.robotdigg.com/product/149/10mm-bore-32-teeth-gt2-pulley GT2 pulley 32 tooth 10mm bore]<br />
* [http://www.robotdigg.com/product/24/GT2-Pulley-36-Teeth-5mm-Bore 2GT pulley 36 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/66/2gt-pulley-36-teeth-8mm-bore 2GT pulley 36 teeth, 8mm bore]<br />
* [http://www.robotdigg.com/product/116/2gt-pulley-40-teeth-5mm-bore 2GT pulley 40 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/66/2gt-pulley-36-teeth-8mm-bore 2GT pulley 40 teeth, 6.35mm bore]<br />
* [http://www.robotdigg.com/product/146/GT2-40-Tooth-8mm-Bore-Pulley 2GTpulley 40 teeth, 8mm bore]<br />
MOQ 50pcs for Custom Pulleys.<br />
<br />
== Cable ==<br />
*Synchromesh<br />
**https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=5503&GroupID=312<br />
**https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=84751&GroupID=768</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Belts_and_Pulleys&diff=124684Belts and Pulleys2014-05-02T08:48:29Z<p>Merlucin: /* Belts */</p>
<hr />
<div>{{Merge|GT2_Timing_Belt}}<br />
[[Category:Suppliers_by_Part]]<br />
<br />
See also [[Choosing_Belts_and_Pulleys]]<br />
<br />
==Belts==<br />
<br />
See also [[GT2 Timing Belt]]<br />
<br />
{| class="wikitable sortable"<br />
|+ <br />
|- style="background-color:#f0f0f0;"<br />
! Supplier !! From !! Type available !! Pitch !! Width !! Length !! Material !! Additional notes <br />
|-<br />
| [http://www.3distributed.com/collections/frontpage/products/gt2-timing-belt 3Distributed] || UK || GT2 || 2mm || 6mm || Sold by the metre || Fiberglass reinforced neoprene rubber. || Delivers Worldwide <br />
|-<br />
| [http://www.think3dprint3d.com/Hardware Think3DPrint3D] || UK || GT2, T2.5 || 2 mm, 2.5 mm || 6 mm || sold by the meter || fiberglass reinforced rubber, steel-reinforced polyurethane|| fast world-wide delivery and excellent customer service<br />
|-<br />
|[http://3dacessorieshub.com/ 3D Acessories Hub] || India || GT2 <BR> T2.5 || 2 mm <BR> 2 mm || 660mm closed <BR> as per your requirement || || Rubber <BR> <br />
polyurethane || -<br />
|-<br />
|[http://3dprinterczar.com/shop/hardware/gt2-pulley-belt/ 3D Printer Czar] || US || GT2 || 2 mm || 6 mm || at your choice|| Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://www.robotdigg.com/category/9/Timing-Pulley&Belt 3DCracker] || CN ||[http://www.robotdigg.com/category/9/Timing-Pulley&Belt GT2] || 2 mm || 6 mm || 900mm, 976mm, 1220mm, 1350mm|New-add '''1524mm closed-loop''', etc and open ended || Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://www.reprap.cn/ He3D] || CN || GT2, MXL, T2.5, T5 || 2.5 mm || 6 mm || 1350mm 990mm and open ended || Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://reprapuniverse.com/catalog/product_info.php?cPath=30_73&products_id=67 ReprapUniverse.com] || Netherlands || T2.5 || 2.5 mm || 5 mm || sold by the meter || Open ended Neoprene Rubber with Fiberglass Reinforced|| Perfect timing belt for Prusa Mendel i2, Prusa i3, MendelMax 1.5. Cheap International Shipping.<br />
|-<br />
| [http://www.3dmakerworld.com 3DMakerWorld] || US || GT2 || 2 mm || 6 mm || 1164 mm || Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://www.charlies3dtechnologies.eu/Belts_and_Pulleys/cat1675912_1594189.aspx Charlie's 3D Technologies] || Belgium || MXL and GT2 || - || - || - || - || -<br />
|-<br />
| [http://www.cubic-print.com Cubic Print] || Germany || T2.5 <BR> T5 || 2.5 mm <BR> 5 mm|| 6 mm || as you wish || PU + steel || open belts<br />
|-<br />
| [http://www.bbman.com/ BBMan] || US || Imperial/Metric<br />
|-<br />
| [http://www.beltingonline.com/ Belting Online] || UK || GT2, MXL, T2.5, T5 || 2 mm 2.5 & 5mm|| As you wish || As you wish|| PU & Neoprene Rubber || Genuine Branded Quality Products <br />
|-<br />
<br />
| [http://easyreprap.com/shop/article_19/GT2-Belt-_-Pulley-Set.html Easy RepRap] || USA ||Precision GT2 || 2 mm || 6 mm || 1150mm || Fiberglass Reinforced || GT2 Belt/Pulley Sets<br />
|-<br />
<br />
| [http://www.ebay.com/sch/yellowvirtualsales/m.html eBay: Yellowvirtualsales] || USA ||Precision GT2 || 2 mm || 6 mm || Cut To Length || Fiberglass Reinforced || Fast Worldwide Shipping<br />
|-<br />
| [http://www.econobelt.com/Timing_Belts.htm Econobelt] || US || many<br />
|-<br />
| [http://www.timing-belt-manufacturer.com/contact.html Eke] || China || many<br />
|-<br />
| [http://www.indiamart.com/bm-beltings-company/industrial-belts.html#open-end-polyurethane Indiamart] || India || many<br />
|-<br />
| [https://www.inventables.com/categories/frame-rail/belting Inventables] || US|| MXL || - || - || 1 foot increments || - || -<br />
|-<br />
| [http://www.kainabelt.com KainaBelt] || China || many<br />
|-<br />
| [http://makemendel.com/mechanical-parts/t2-5-timing-belt Makemendel] || India || GT2 <BR> T2.5 || 2mm <BR> 2.5 mm || 7 mm <BR> 7mm || Open Belt || PU || Open Belts for all Reprap and other 3D printers. Available in custom length.<br />
|-<br />
| [http://www.megadyne.it/ Megadyne] || Italy || many<br />
|-<br />
| [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1175 Misumi] || multiple<br />
|-<br />
| [http://www.paoparts.com/fr/15-courroies Paoparts] || France || T2.5 <br> T5 || 2,5mm <br> 5mm || 5mm || - || PU ||<br />
|-<br />
| [http://shop.polybelt.com/Metirc-Pitch-Open-End-Belt-Roll_c29.htm PolyBelt] || US || T2.5 <br> T5 || 5 mm || 6 mm || - || polyurethane + steel || -<br />
|-<br />
| [http://reprapworld.com/?searchresults&cPath=1595_1611 RepRapWorld] || Netherlands || T2.5 <br> T5 || 2,5 mm <br> 5 mm || 5 mm <br> 5 mm || 1 m || neoprene<br>polyurethane + steel || -<br />
|-<br />
| [http://www.robotdigg.com RobotDigg] || China || [http://www.robotdigg.com/product/10/Open-Ended-6mm-Width-GT2-Belt GT2], MXL, T2.5 || 2 mm || 6mm, 6.35mm or 9mm || 20M or 50M per roll ,[http://www.robotdigg.com/product/38/Closed-loop-GT2-Belt,-101-Teeth-202mm-Long Closed-loop GT2]|| Neoprene Rubber, Fiberglass Reinforced. MOQ 50M<br />
|<br />
|-<br />
| [http://www.royalsupply.com/store/pc/Gates-2MR-1164-06-PowerGrip-GT2-V-Belt-2MR-and-3MR-93901582-1036p17193.htm Royal supply] || US || GT2 || 2 mm || 6 mm || 1164 mm || fiberglass / nylon / neoprene || -<br />
|-<br />
| [https://sdp-si.com SDP-SI] || US || Imperial/Metric<br />
|-<br />
| [http://techpaladin.com/store/#ecwid:category=1941327&mode=product&product=9001827 TechPaladin] || US || GT2 || 2 mm || 5 mm || 1160 mm || neoprene || -<br />
|-<br />
| [http://www.tanals.com/fr/courroies-dentees-neoprene/ Tanals] || France || many || - || - || - || - || don't sell to individuals<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || Spain || GT2 || 2mm || 5 or 6 mm || Sold by the meter, open ended || Neoprene Rubber || Worldwide shipping<br />
|-<br />
| [http://www.tridprinting.com/Mechanical-Parts/ TriDPrinting.com] || US || GT2 || 2 mm || 6 mm || Sold by the meter, open ended || Neoprene, Fiberglass Reinforced || 50 m max, Worldwide Delivery<br />
|-<br />
| [http://www.RepRap-India.com RepRap-India.com] || IN || GT2 || 2 mm || 6 mm || open ended || Neoprene, fiberglass reinforced || 50 m max<br />
|-<br />
|}<br />
<br />
<br />
<br />
{| class="wikitable sortable"<br />
|- style="background-color:#f0f0f0;"<br />
! Vendor !! Loc. !! Product !! Width !! Pitch !! Length !! class="unsortable" | Additional notes<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/collections/frontpage/products/gt2-timing-belt GT2 Belt] || 6mm || 2.00mm || Multiples of 1000mm || &nbsp;<br />
|-<br />
| Think3DPrint3D || UK || [http://www.think3dprint3d.com/Hardware/GT2-Timing-Belt GT2 Belt] || 6 mm || 2.00 mm || multiples of 1000 mm || &nbsp;<br />
|-<br />
| 3D Acessories Hub || IN|| [http://www.3dacessorieshub.com GT2 Belt] || 7 mm || 2.00 mm || 660 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ 3DCracker&RobotDigg]|| CN || [http://www.robotdigg.com/product/160/1524mm-long-762-teeth-closed-loop-gt2-belt-for-rostock 1524mm Endless GT2 Belt] || 6 mm || 2.00 mm || 1524 mm || &nbsp;<br />
|-<br />
| 3DCracker || CN || [http://www.3dcracker.com GT2 Belt] || 6 mm || 2.00 mm || Open ended and closed-loop || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/xy-gt2-timing-belt-pulley-kit-1 Prusa Kit] || 6 mm || 2.00 mm || 1000 mm || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/d-gt2-timing-belt-pulley-kit Rostock/Delta Kit] || 6 mm || 2.00 mm || 1000 mm || &nbsp;<br />
|-<br />
| 3DMakerWorld || US || [http://www.3dmakerworld.com/store/parts-accessories/hardware/gt2-timing-belt Belt] || 6 mm || 2.00 mm || 1164 mm || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_belts Belt] || 3 mm || 2.00 mm || 54-1910 mm || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_belts Belt] || 6 mm || 2.00 mm || 54-1910 mm || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_belts Belt] || 9 mm || 2.00 mm || 54-1910 mm || &nbsp;<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-900mm-x-6mm-450-teeth-11958 Separate Belt at 900mm length] || 6&nbsp;mm || 2.00 mm || 900 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-976mm-x-6mm-488-teeth-11959 Separate Belt at 976mm length] || 6&nbsp;mm || 2.00 mm || 976 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1032mm-x-6mm-516-teeth-12179 Separate Belt at 1032mm length] || 6&nbsp;mm || 2.00 mm || 1032 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1164mm-x-6mm-582-teeth-11960 Separate Belt at 1164mm length] || 6&nbsp;mm || 2.00 mm || 1164 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1386mm-x-6mm-693-teeth-12181 Separate Belt at 1386mm length] || 6&nbsp;mm || 2.00 mm || 1386 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1524mm-x-6mm-762-teeth-12180 Separate Belt at 1524mm length] || 6&nbsp;mm || 2.00 mm || 1524 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/universal-gt2-belts-pulleys-kit-for-reprap-other-3d-printers-11954 Universal Kit for RepRap/Other 3D Printers] || 6 mm || 2.00 mm || 1032 & 1164 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-reprap-prusa-11950 Kit for RepRap Prusa] || 6 mm || 2.00 mm || 900 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-delta-robot-11953 Kit for Rostock Delta Robot] || 6 mm || 2.00 mm || 1524 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-mini-11952 Kit for Rostock Mini] || 6&nbsp;mm || 2.00 mm || 1032 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Charlie's 3D Technologies || BE || [http://www.charlies3dtechnologies.eu/GT2_Belt_1_m/p1675911_9494987.aspx Belt] || 6 mm || 2.03 mm || 1000 mm || &nbsp;<br />
|-<br />
| Cubic-Print || DE || [http://www.cubic-print.de GT2 Belt kit] || 6 mm || 2.00 mm || cut to length || &nbsp;<br />
|-<br />
| eBay: fabster3d || CN || [http://www.ebay.com/sch/fabster3d/m.html Belt] || 6 mm || &nbsp; || 974-1164 mm || &nbsp;<br />
|-<br />
| eBay: yellowvirtualsales || US || [http://www.ebay.com/sch/yellowvirtualsales/m.html Precision GT2 Belt] || 6 mm || 2.00 mm || Cut To Length || &nbsp;<br />
|-<br />
| EmotionTech || FR || [http://www.reprap-france.com/68-kit-de-courroies-gt2.html Belt] || 6 mm || 2.00 mm || 850 mm || &nbsp;<br />
|-<br />
| Fabberworld || CH || [http://www.fabberworld.com/Pulleys-and-Timing-Belts/GT2-Timing-Belt-by-the-meter::39.html Belt] || 6 mm || 2.00 mm || 1000+ mm || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=74 Kit for RepRap Prusa 2] || 6 mm || &nbsp; || 976 mm x 3 || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=75 Kit for Rostock Mini] || 6 mm || &nbsp; || 900 mm x 3 || &nbsp;<br />
|-<br />
| Makemendel || IN|| [http://makemendel.com/mechanical-parts/mechanical-parts-1/pulleys-and-belts/gt2-open-belt GT2 Belt] || 7 mm || 2.00 mm || 1000 mm and more || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302190510/ 2GT Belt] || 4 mm || 2.00 mm || 662-9942 mm || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302190510/ 2GT Belt] || 6 mm || 2.00 mm || 662-9942 mm || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302190510/ 2GT Belt] || 9 mm || 2.00 mm || 662-9942 mm || &nbsp;<br />
|-<br />
| ReprapWorld.com || EU || [http://reprapworld.com/?searchresults&cPath=1655] || 6 mm || 2.00 mm || 1000-75000 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/38/Closed-loop-GT2-Belt,-101-Teeth-202mm-Long 202mm Closed-loop GT2 Belt] || 6 mm || 2.00 mm || 202 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/48/760mm-380-teeth-Closed-loop-6mm-Width-GT2-Belt 760mm Closed-loop GT2 Belt] || 6 mm || 2.00 mm || 760 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/160/1524mm-long-762-teeth-closed-loop-gt2-belt-for-rostock 1524mm Endless GT2 Belt] || 6 mm || 2.00 mm || 1524 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/10/Open-Ended-6mm-Width-GT2-Belt GT2 Belt Open Ended] || 6 mm || 2.00 mm || 1000-50000 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/22/MXL-Belt,-6mm-Width-Open-Ended MXL Belt] || 6 mm || 2.00 mm || 1000-50000 mm || &nbsp;<br />
|-<br />
| RoyalSupply || US || [http://www.royalsupply.com/store/pc/Gates-2MR-1164-06-PowerGrip-GT2-V-Belt-2MR-and-3MR-93901582-1036p17193.htm#details Belt] || 6 mm || 2.00 mm || 1164 mm || &nbsp;<br />
|-<br />
| TechPaladin Printing || US || [http://techpaladin.com/store/#!/~/product/id=9001827 Belt] || 6 mm || 2.00 mm || 1380 mm || &nbsp;<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || ES || [http://store.thingibox.com/en/powertransmission/7-gt2_timing_belt.html GT2 Belt] || 5 or 6 mm || 2.00 mm || Multiples of 1m || Worldwide shipping<br />
|-<br />
|[http://www.TriDPrinting.com/ TriDPrinting.com]|| US || [http://www.TriDPrinting.com/Mechanical-Parts/ GT2 Belt Open Ended] || 6 mm || 2.00 mm || 1000-50000 mm || Worldwide Delivery;<br />
|-<br />
| Ultibots || US || [http://www.ultibots.com/gt2-timing-belt-1164mm/ Belt] || 6 mm || 2.00 mm || 1164 mm || &nbsp;<br />
|}<br />
<br />
<br />
<br />
There is also some on ebay.<br />
<br />
*beside GT2 belts, there is also 2M that have a 2mm round pitch (like [http://www.powerdrive-belt.com/new/products.asp?x=1&id=16&id2=69&id4=2&t=1] and many other suppliers)<br />
<br />
==Pulleys==<br />
<br />
See also [[GT2 Timing Belt]].<br />
<br />
{| class="wikitable sortable"<br />
|+ <br />
|- style="background-color:#f0f0f0;"<br />
! Supplier !! From !! Type available !! Pitch !! Tooth !! Size (bore, OD,...) !! Max belt width !! Material !! Additional notes <br />
|-<br />
| [http://www.3distributed.com/products/gt2-pulley 3Distributed] || UK || GT2 || 2mm || 20 || 5mm || 6mm || Aluminium with grub screws || Delivers Worldwide<br />
|-<br />
| [http://www.think3dprint3d.com/Hardware/t2.5-16-ToothTimingPulley-M4GrubScrews Think3DPrint3D] || UK || T2.5 || 2.5 mm || 16 || 5 mm || 7 mm || Aluminum with zinc plated steel flanges|| fast delivery and excellent customer service!<br />
|-<br />
| [http://www.robotdigg.com/category/9/Timing-Pulley&Belt 3DCracker&RobotDigg] || CN || GT2 || 2 mm || 16, 20, 36 || 5 mm or 8mm || 7 mm || All Aluminum || -<br />
|-<br />
| [http://www.3dmakerworld.com 3DMakerWorld] || US || GT2 || 2 mm || 20 & 36 || 5 mm || 6 mm || Aluminium & Polycarbonate with brass insert || -<br />
|-<br />
| [http://reprapuniverse.com/catalog/product_info.php?products_id=68 ReprapUniverse.com] || Netherlands || T2.5 || 2.5mm || 16 || 5 mm || 6 mm || Aluminum + M3 grub screws || Quality Aluminum Pulleys. Perfect for Reprap 3D Printers: Prusa Mendel i2, Prusa i3, MendelMax 1.5 & others. Cheap International Shipping.<br />
|-<br />
| [http://www.charlies3dtechnologies.eu/Belts_and_Pulleys/cat1675912_1594189.aspx Charlie's 3D Technologies] || Belgium || MXL and GT2 || - || 15 or 20 || -|| - || - || -<br />
|-<br />
| [http://www.cubic-print.com Cubic Print] || Germany || T2.5 <BR> T5 || 2.5mm <BR> 5 mm || 8, 16 || 5 mm || 7 mm || alu + steel grub screws || -<br />
|-<br />
| [http://www.bbman.com/ BBMan] || US || many<br />
|-<br />
| [http://www.beltingonline.com/timing-pulleys-272/ Belting Online] || UK || GT2, T2.5, T5 & MXL || 2mm, 2.5mm, 2.03mm & 5mm ||16, 18, 20, 36 <BR> Also Special Made to order if required || 5mm <BR> Specials sizes are possible. || 6mm || Alu + Grub Screws || Quality Pulleys Manufactured in the UK. <br />
|-<br />
| [http://www.econobelt.com/e-store/Pulleys.htm Econobelt] || US || many<br />
|-<br />
| [http://www.ebay.com/sch/m.html?_odkw=&item=181168182751&pt=BI_Heavy_Equipment_Parts&_osacat=0&hash=item2a2e7715df&_ssn=yellowvirtualsales&_trksid=p2046732.m570.l1313&_nkw=pulley&_sacat=0&_from=R40 eBay: Yellowvirtualsales] || USA || GT2, HDT3M || 2MM / 3MM|| 12-36 || 5 mm || 6-10MM mm || Fiberglass Reinforced || Fast Worldwide Shipping<br />
|-<br />
| [https://www.inventables.com/categories/frame-rail/pulleys Inventables] || US|| MXL || - || - || - || - || - || - <br />
|-<br />
| [http://makemendel.com/mechanical-parts/t2-5-pulley MakeMendel] || India || GT2 <BR> T2.5 || 2 <BR> 2.5 mm || 20 <BR> 12 or 16 || 5 mm || 7mm || Aluminium with grub screws || T2.5 pulley is available in 12 teeth and 16 teeth as well. Suitable for all 3D printers. Shipping is worldwide<br />
|-<br />
| [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1097 Misumi] || multiple<br />
|-<br />
| [http://www.paoparts.com/fr/15-courroies Paoparts] || France || T2,5 <br> T5<br />
|-<br />
| [http://reprapworld.com/?products_details&products_id=247 RepRapWorld] || Netherlands || T5 || 5 mm || 8 || 5 mm x 17 mm x 20 mm || ? || Alu || Pulley profile has play resulting in lash when reversing<br />
|-|-<br />
| [http://www.robotdigg.com/ RobotDigg] || China || [http://www.robotdigg.com/category/9/Timing-Pulley&Belt GT2], T2.5 and MXL || 2mm, 2.5mm, 2.03mm || 16, 18, 20, 36 || 5*17.5*18 mm || 7mm || Alu || SKYPE: robotdigg<br />
|-<br />
| [http://www.royalsupply.com/store/pc/Gates-2MR-18S-06-PowerGrip-GT2-Sprockets-2MR-and-3MR-78426007-1555p42023.htm#details Royal Supply] || US || GT2 || 2 mm || 18 || 4,7 mm || 6 mm || Alu || you'll need to redrill the bore (3/16") to fit usual 5 mm motor shaft<br />
|-<br />
| [https://sdp-si.com SDP-SI] || US || many<br />
|-<br />
| [http://techpaladin.com/store/#ecwid:category=1941327&mode=product&product=9188440 TechPaladin] || US || GT2 || 2 mm || 36 || 5 mm || 6 mm || plastic/bronze || -<br />
|-<br />
| [http://www.TriDPrinting.com/Mechanical-Parts/ TriDPrinting.com] || US || GT2 || 2 mm || 16, 20 || 5 mm || 6 mm || Aluminium with grub screws || Uses two set screws, Worldwide Delivery<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || Spain || GT2 || 2 mm || 16 || 5 mm || 4-6 mm || Aluminium + grub screws || Worldwide shipping<br />
|-<br />
| [http://ultimachine.com/content/timing-pulley-gt2-20-tooth Ultimachine] || US || GT2 || 2 mm || 20 || 5 mm || 6 mm || Alu || use two set screws<br />
|-<br />
| [http://RepRap-India.com RepRap-India.com] || US || GT2 || 2 mm || 20 || 5 mm || 6 mm || Alu || use two set screws<br />
|-<br />
| [http://RepRap-India.com RepRap-India.com] || US || T2.5 || 2 mm || 20 || 5 mm || 6 mm || Alu || use two set screws<br />
|-<br />
<br />
|}<br />
<br />
<br />
<br />
{| class="wikitable sortable"<br />
|- style="background-color:#f0f0f0;"<br />
! Vendor !! Loc. !! Product !! Material !! Belt width !! Bore !! Tooth !! Flange !! class="unsortable" | Additional notes<br />
|-<br />
| 3D Acessories Hub || IN || [http://www.3dacessorieshub.com GT2 Pulley] || Aluminium || 7 mm || 5.00 mm || 20 || - || &nbsp;<br />
|-<br />
| 3DCracker || CN || [http://www.3dcracker.com GT2 Pulley] || &nbsp; || 7 mm || 5, 8mm || 16, 20, 36 || double || &nbsp;<br />
|-<br />
| eBay: Yellowvirtualsales|| US || [http://www.ebay.com/sch/m.html?_odkw=gt2&_osacat=0&_from=R40&_ssn=yellowvirtualsales&_trksid=p2046732.m570.l1313.TR11.TRC1.A0.Xpulley.TRS0&_nkw=pulley&_sacat=0 Timing Pulleys] || Aluminum, Metal || 6mm - 10mm || 5.00 mm || 12-36 || Vary || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/collections/frontpage/products/gt2-pulley Pulley] || &nbsp; || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/xy-gt2-timing-belt-pulley-kit-1 Prusa Kit] || &nbsp; || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/d-gt2-timing-belt-pulley-kit Rostock/Delta Kit] || &nbsp; || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| 3DMakerWorld || US || [http://www.3dmakerworld.com/store/parts-accessories/hardware GT2 Timing Pulley] || Aluminium & Polycarbonate with brass insert || 6 mm || 5.00 mm || 20 & 36 || double || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_pulley Pulley] || Aluminium || 3 mm || 5.00 mm || 12-20 || double || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_pulley Pulley] || Aluminium || 6 mm || 5.00 mm || 12-20 || double || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_pulley Pulley] || Aluminium || 9 mm || 5.00 mm || 12-20 || double || &nbsp;<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-pitch-pulley-20-tooth-c-w-5mm-h7-bore-2-x-m3-g-s-11970 Separate Timing Pulley (sold each)] || Aluminium || 6 mm || 5.00 mm || 20 || double || UK Manufactured Precision Pulley<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/universal-gt2-belts-pulleys-kit-for-reprap-other-3d-printers-11954 Universal Kit for RepRap/Other 3D Printers] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-reprap-prusa-11950 Kit for RepRap Prusa] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-delta-robot-11953 Kit for Rostock Delta Robot] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-mini-11952 Kit for Rostock Mini] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Charlie's 3D Technologies || BE || [http://www.charlies3dtechnologies.eu/GT2_Pulley_Deluxe_1_pcs/p1675911_9495003.aspx Pulley] || Aluminium, nylon || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Charlie's 3D Technologies || BE || [http://www.charlies3dtechnologies.eu/GT2_Alu_Pulley_Deluxe_1_pcs/p1675911_9652574.aspx Pulley] || Aluminium || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Cubic-Print || DE || [http://www.cubic-print.com Pulley / Kit] || Aluminium || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| eBay: fabster3d || CN || [http://www.ebay.com/sch/fabster3d/m.html Pulley] || Aluminium (black) || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| EmotionTech || FR || [http://www.reprap-france.com/69-poulie-gt2.html Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Fabberworld || CH || [http://www.fabberworld.com/Pulleys-and-Timing-Belts/GT2-Pulley-20-Tooth-Aluminium::40.html Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=74 Kit for RepRap Prusa 2] || Aluminium (black) || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=75 Kit for Rostock Mini] || Aluminium (black) || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Makemendel || IN || [http://makemendel.com/mechanical-parts/mechanical-parts-1/gt2-pulley GT2 Pulley] || Aluminium || 7 mm || 5.00 mm || 20 || - || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302193470/ 2GT Pulley] || Aluminium || 4 mm || 5.00 mm || 32 || double || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302193470/ 2GT Pulley] || Aluminium || 6 mm || 5.00 mm || 32 || double || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302193470/ 2GT Pulley] || Aluminium || 9 mm || 5.00 mm || 32 || double || &nbsp;<br />
|-<br />
| Misumi || Japan || [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=metric2010&page=1095 Misumi's pulley introduction] || ? || ? || ? || ? || ?<br />
|<br />
Another good source for GT2 pulleys and belts is Misumi. They carry a huge variety of suitable pulleys, including several that are closer to out ideal diameter. In addition, Misumi has offices around the globe so they are a better choice for international customers (though some regions will only sell to businesses).<br />
<br />
Their website does not make it easy to browse for belts and pulleys, but here are the relevent pages in their catalog:<br />
<br />
* [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1097 Pulleys]<br />
* [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1175 Belts]<br />
* [http://www.sdp-si.com/D265/HTML/D265T003.html Handbook of Timing Belts and Pulleys]<br />
<br />
Note: Misumi calls theirs 2GT (2mm pitch) and 3GT (3mm pitch). As far as I know they are compatible with GT2, but both offer the same benefits. Misumi's pulleys seem expensive, but they are metal pulleys. We don't really need metal pulleys for our needs, but they are fine.<br />
<br />
<br />
|-<br />
| ReprapWorld.com || EU || [http://reprapworld.com/?searchresults&cPath=1655 Multiple types of Pulley] || Aluminium || 5-6 mm || 5mm || Multiple || double || &nbsp;<br />
|-<br />
| [http://www.robotdigg.com/ Robotdigg] || CN || [http://www.robotdigg.com/product/59/Rostock-16-Teeth-5mm-Bore-GT2-Pulley 16Teeth 2GT Pulley] || Aluminium || 7 mm || 5mm, 8mm || 16 || double || &nbsp;<br />
|-<br />
| [http://www.robotdigg.com/ Robotdigg] || CN || [http://www.robotdigg.com/product/9/GT2-Pulley-20-Teeth-5mm-Bore GT2 Pulley] || Aluminium || 7 mm || 5mm, 8mm || 20 || double || &nbsp;<br />
|-<br />
| [http://www.robotdigg.com/ Robotdigg] || CN || [http://www.robotdigg.com/product/24/GT2-Pulley-36-Teeth-5mm-Bore GT2 Pulley] || Aluminium || 7 mm || 5mm || 36 || double || &nbsp;<br />
|-<br />
| RoyalSupply || US || [http://www.royalsupply.com/store/pc/Gates-2MR-18S-06-PowerGrip-GT2-Sprockets-2MR-and-3MR-78426007-1555p42023.htm#details Pulley] || Aluminium || 4-6 mm || 4.76 mm || 18 || double || You'll need to redrill them to fit on the usual 5mm motor shaft<br />
|-<br />
| Stock Drive Products || US || https://sdp-si.com/ || &nbsp; || &nbsp; || 5.00 mm || [https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=22736&GroupID=347 36], [https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=8545&GroupID=347 40], [https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=55836&GroupID=347 42] || &nbsp;<br />
| In the US, a popular source is SDP/SI. They sell a huge variety of belts and pulleys that meet our needs. Always call SDP/SI for stock, their website is always out of date.<br />
<br />
* [https://sdp-si.com/eStore/Direct.asp?GroupID=347 Pulleys (bad link)]<br />Filter for GT2, 2mm pitch, then choose the bore size needed for your steppers.<br />
* [https://sdp-si.com/eStore/Direct.asp?GroupID=342 Belts (bad link)]<br />Filter on GT2, 2mm Pitch, and get 2 belts as close to 1m long as possible.<br />
<br />
Note, unfortunately, SDP/SI does not carry a smaller diameter GT2 pulley with a 5mm bore, so to buy your pulleys here you need a larger pulley than in strictly ideal. These are fine, though. I ([[User:Virtlink|Virtlink]] ?) use the 36 tooth pulleys on my printer and they work great.<br />
|-<br />
| TechPaladin Printing || US || [http://techpaladin.com/store/#!/~/product/category=1941327&id=18833859 Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || ES || [http://store.thingibox.com/en/powertransmission/8-pulleys.html GT2 Pulley] || Aluminium || 4-6 mm || 5.00 mm || 16 || double || Length: 7mm; Worldwide shipping<br />
|-<br />
| [http://www.TriDPrinting.com/ TriDPrinting.com] || US || [http://www.TriDPrinting.com/Mechanical-Parts/ GT2 Pulley] || Aluminium || 6 mm || 5.00 mm || 16, 20 || double || Worldwide Delivery<br />
|-<br />
| Ultibots || US || [http://www.ultibots.com/gt2-timing-pulley-20-tooth/ Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| UltiMachine || US || [https://ultimachine.com/content/timing-pulley-gt2-20-tooth Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|}<br />
<br />
=== RobotDigg ===<br />
China manufacturer of T2.5 pulley, MXL pulley, GT2 pulleys. T2.5 belt, MXL belt and GT2 belt in different width, open ended and endless or closed-loop timing belt provider.<br />
T2.5 pulley 16 tooth 5mm bore<br />
T5 pulley 12 tooth 8mm bore<br />
MXL pulley 18 teeth 5mm bore<br />
MXL pulley 20 teeth 6.35mm bore<br />
MXL pulley 36 teeth 5mm bore<br />
MXL pulley 36 teeth 8mm bore<br />
GT2 pulley 16 teeth 5mm bore<br />
GT2 pulley 18 tooth 6.35mm bore<br />
GT2 pulley 20 teeth 5mm, 6.35mm bore and 8mm bore<br />
GT2 pulley 32 tooth 10mm bore<br />
GT2 pulley 36 teeth 5mm bore and 8mm bore<br />
GT2 pulley 40 tooth 5mm, 6.35mm 8mm bore n 10mm bore<br />
* [http://www.robotdigg.com/product/25/T2.5-pulley,-16-teeth,-5mm-bore T2.5 pulley, 16 tooth, 5mm bore]<br />
* [http://www.robotdigg.com/product/26/MXL-pulley,-18-tooth,-5mm-bore MXL pulley 18 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/147/36-Tooth-MXL-Pulley-with-5mm-Bore MXL pulley 36 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/148/36-Tooth-MXL-Pulley-with-8mm-Bore MXL pulley 36 teeth, 8mm bore]<br />
* [http://www.robotdigg.com/product/59/Rostock-16-Teeth-5mm-Bore-GT2-Pulley 2GT pulley 16 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/9/GT2-Pulley-20-Teeth-5mm-Bore 2GT pulley 20 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/23/GT2-Pulley-20-Teeth-8mm-Bore 2GT pulley 20 teeth, 8mm bore]<br />
* [http://www.robotdigg.com/product/149/10mm-bore-32-teeth-gt2-pulley GT2 pulley 32 tooth 10mm bore]<br />
* [http://www.robotdigg.com/product/24/GT2-Pulley-36-Teeth-5mm-Bore 2GT pulley 36 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/66/2gt-pulley-36-teeth-8mm-bore 2GT pulley 36 teeth, 8mm bore]<br />
* [http://www.robotdigg.com/product/116/2gt-pulley-40-teeth-5mm-bore 2GT pulley 40 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/66/2gt-pulley-36-teeth-8mm-bore 2GT pulley 40 teeth, 6.35mm bore]<br />
* [http://www.robotdigg.com/product/146/GT2-40-Tooth-8mm-Bore-Pulley 2GTpulley 40 teeth, 8mm bore]<br />
MOQ 50pcs for Custom Pulleys.<br />
<br />
== Cable ==<br />
*Synchromesh<br />
**https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=5503&GroupID=312<br />
**https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=84751&GroupID=768</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Belts_and_Pulleys&diff=124683Belts and Pulleys2014-05-02T08:47:46Z<p>Merlucin: /* Belts */</p>
<hr />
<div>{{Merge|GT2_Timing_Belt}}<br />
[[Category:Suppliers_by_Part]]<br />
<br />
See also [[Choosing_Belts_and_Pulleys]]<br />
<br />
==Belts==<br />
<br />
See also [[GT2 Timing Belt]]<br />
<br />
{| class="wikitable sortable"<br />
|+ <br />
|- style="background-color:#f0f0f0;"<br />
! Supplier !! From !! Type available !! Pitch !! Width !! Length !! Material !! Additional notes <br />
|-<br />
| [http://www.3distributed.com/collections/frontpage/products/gt2-timing-belt 3Distributed] || UK || GT2 || 2mm || 6mm || Sold by the metre || Fiberglass reinforced neoprene rubber. || Delivers Worldwide <br />
|-<br />
| [http://www.think3dprint3d.com/Hardware Think3DPrint3D] || UK || GT2, T2.5 || 2 mm, 2.5 mm || 6 mm || sold by the meter || fiberglass reinforced rubber, steel-reinforced polyurethane|| fast world-wide delivery and excellent customer service<br />
|-<br />
|[http://3dacessorieshub.com/ 3D Acessories Hub] || India || GT2 <BR> T2.5 || 2 mm <BR> 2 mm || 660mm closed <BR> as per your requirement || || Rubber <BR> <br />
polyurethane || -<br />
|-<br />
|[http://3dprinterczar.com/shop/hardware/gt2-pulley-belt/ 3D Printer Czar] || US || GT2 || 2 mm || 6 mm || at your choice|| Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://www.robotdigg.com/category/9/Timing-Pulley&Belt 3DCracker] || CN ||[http://www.robotdigg.com/category/9/Timing-Pulley&Belt GT2] || 2 mm || 6 mm || 900mm, 976mm, 1220mm, 1350mm|New-add '''1524mm closed-loop''', etc and open ended || Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://www.reprap.cn/ He3D] || CN || GT2, MXL, T2.5, T5 || 2.5 mm || 6 mm || 1350mm 990mm and open ended || Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://reprapuniverse.com/catalog/product_info.php?cPath=30_73&products_id=67 ReprapUniverse.com] || Netherlands || T2.5 || 2.5 mm || 5 mm || sold by the meter || Open ended Neoprene Rubber with Fiberglass Reinforced|| Perfect timing belt for Prusa Mendel i2, Prusa i3, MendelMax 1.5. Cheap International Shipping.<br />
|-<br />
| [http://www.3dmakerworld.com 3DMakerWorld] || US || GT2 || 2 mm || 6 mm || 1164 mm || Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://www.charlies3dtechnologies.eu/Belts_and_Pulleys/cat1675912_1594189.aspx Charlie's 3D Technologies] || Belgium || MXL and GT2 || - || - || - || - || -<br />
|-<br />
| [http://www.cubic-print.com Cubic Print] || Germany || T2.5 <BR> T5 || 2.5 mm <BR> 5 mm|| 6 mm || as you wish || PU + steel || open belts<br />
|-<br />
| [http://www.bbman.com/ BBMan] || US || Imperial/Metric<br />
|-<br />
| [http://www.beltingonline.com/ Belting Online] || UK || GT2, MXL, T2.5, T5 || 2 mm 2.5 & 5mm|| As you wish || As you wish|| PU & Neoprene Rubber || Genuine Branded Quality Products <br />
|-<br />
<br />
| [http://easyreprap.com/shop/article_19/GT2-Belt-_-Pulley-Set.html Easy RepRap] || USA ||Precision GT2 || 2 mm || 6 mm || 1150mm || Fiberglass Reinforced || GT2 Belt/Pulley Sets<br />
|-<br />
<br />
| [http://www.ebay.com/sch/yellowvirtualsales/m.html eBay: Yellowvirtualsales] || USA ||Precision GT2 || 2 mm || 6 mm || Cut To Length || Fiberglass Reinforced || Fast Worldwide Shipping<br />
|-<br />
| [http://www.econobelt.com/Timing_Belts.htm Econobelt] || US || many<br />
|-<br />
| [http://www.timing-belt-manufacturer.com/contact.html Eke] || China || many<br />
|-<br />
| [http://www.indiamart.com/bm-beltings-company/industrial-belts.html#open-end-polyurethane Indiamart] || India || many<br />
|-<br />
| [https://www.inventables.com/categories/frame-rail/belting Inventables] || US|| MXL || - || - || 1 foot increments || - || -<br />
|-<br />
| [http://www.kainabelt.com KainaBelt] || China || many<br />
|-<br />
| [http://makemendel.com/mechanical-parts/t2-5-timing-belt Makemendel] || India || GT2 <BR> T2.5 || 2mm <BR> 2.5 mm || 7 mm <BR> 7mm || Open Belt || PU || Open Belts for all Reprap and other 3D printers. Available in custom length.<br />
|-<br />
| [http://www.megadyne.it/ Megadyne] || Italy || many<br />
|-<br />
| [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1175 Misumi] || multiple<br />
|-<br />
| [http://www.paoparts.com/fr/15-courroies Paoparts] || France || T2.5 <br> T5 || 2,5mm <br> 5mm || 5mm || - || PU ||<br />
|-<br />
| [http://shop.polybelt.com/Metirc-Pitch-Open-End-Belt-Roll_c29.htm PolyBelt] || US || T2.5 <br> T5 || 5 mm || 6 mm || - || polyurethane + steel || -<br />
|-<br />
| [http://reprapworld.com/?searchresults&cPath=1595_1611 RepRapWorld] || Netherlands || T2.5 <br> T5 || 2,5 mm <br> 5 mm || 5 mm <br> 5 mm || 1 m || neoprene<br>polyurethane + steel || -<br />
|-<br />
| [http://www.robotdigg.com RobotDigg] || China || [http://www.robotdigg.com/product/10/Open-Ended-6mm-Width-GT2-Belt GT2], MXL, T2.5 || 2 mm || 6mm, 6.35mm or 9mm || 20M or 50M per roll ,[http://www.robotdigg.com/product/38/Closed-loop-GT2-Belt,-101-Teeth-202mm-Long Closed-loop GT2]|| Neoprene Rubber, Fiberglass Reinforced. MOQ 50M<br />
|<br />
|-<br />
| [http://www.royalsupply.com/store/pc/Gates-2MR-1164-06-PowerGrip-GT2-V-Belt-2MR-and-3MR-93901582-1036p17193.htm Royal supply] || US || GT2 || 2 mm || 6 mm || 1164 mm || fiberglass / nylon / neoprene || -<br />
|-<br />
| [https://sdp-si.com SDP-SI] || US || Imperial/Metric<br />
|-<br />
| [http://techpaladin.com/store/#ecwid:category=1941327&mode=product&product=9001827 TechPaladin] || US || GT2 || 2 mm || 5 mm || 1160 mm || neoprene || -<br />
|-<br />
| [http://www.tanals.com/fr/courroies-dentees-neoprene/ Tanals] || France || many || - || - || - || - || don't sell to individuals<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || Spain || GT2 || 2mm || 5 or 6 mm || Sold by the meter, open ended || Neoprene Rubber || Worldwide shipping<br />
|-<br />
| [http://www.tridprinting.com/Mechanical-Parts/ TriDPrinting.com] || US || GT2 || 2 mm || 6 mm || Sold by the meter, open ended || Neoprene, Fiberglass Reinforced || 50 m max, Worldwide Delivery<br />
|-<br />
| [http://www.RepRap-India.com RepRap-India.com] || IN || GT2 || 2 mm || 6 mm || open ended || Neoprene, fiberglass reinforced || 50 m max<br />
|-<br />
|}<br />
<br />
<br />
<br />
{| class="wikitable sortable"<br />
|- style="background-color:#f0f0f0;"<br />
! Vendor !! Loc. !! Product !! Width !! Pitch !! Length !! class="unsortable" | Additional notes<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/collections/frontpage/products/gt2-timing-belt GT2 Belt] || 6mm || 2.00mm || Multiples of 1000mm || &nbsp;<br />
|-<br />
| Think3DPrint3D || UK || [http://www.think3dprint3d.com/Hardware/GT2-Timing-Belt GT2 Belt] || 6 mm || 2.00 mm || multiples of 1000 mm || &nbsp;<br />
|-<br />
| 3D Acessories Hub || IN|| [http://www.3dacessorieshub.com GT2 Belt] || 7 mm || 2.00 mm || 660 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ 3DCracker&RobotDigg]|| CN || [http://www.robotdigg.com/product/160/1524mm-long-762-teeth-closed-loop-gt2-belt-for-rostock 1524mm Endless GT2 Belt] || 6 mm || 2.00 mm || 1524 mm || &nbsp;<br />
|-<br />
| 3DCracker || CN || [http://www.3dcracker.com GT2 Belt] || 6 mm || 2.00 mm || Open ended and closed-loop || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/xy-gt2-timing-belt-pulley-kit-1 Prusa Kit] || 6 mm || 2.00 mm || 1000 mm || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/d-gt2-timing-belt-pulley-kit Rostock/Delta Kit] || 6 mm || 2.00 mm || 1000 mm || &nbsp;<br />
|-<br />
| 3DMakerWorld || US || [http://www.3dmakerworld.com/store/parts-accessories/hardware/gt2-timing-belt Belt] || 6 mm || 2.00 mm || 1164 mm || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_belts Belt] || 3 mm || 2.00 mm || 54-1910 mm || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_belts Belt] || 6 mm || 2.00 mm || 54-1910 mm || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_belts Belt] || 9 mm || 2.00 mm || 54-1910 mm || &nbsp;<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-900mm-x-6mm-450-teeth-11958 Separate Belt at 900mm length] || 6&nbsp;mm || 2.00 mm || 900 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-976mm-x-6mm-488-teeth-11959 Separate Belt at 976mm length] || 6&nbsp;mm || 2.00 mm || 976 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1032mm-x-6mm-516-teeth-12179 Separate Belt at 1032mm length] || 6&nbsp;mm || 2.00 mm || 1032 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1164mm-x-6mm-582-teeth-11960 Separate Belt at 1164mm length] || 6&nbsp;mm || 2.00 mm || 1164 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1386mm-x-6mm-693-teeth-12181 Separate Belt at 1386mm length] || 6&nbsp;mm || 2.00 mm || 1386 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1524mm-x-6mm-762-teeth-12180 Separate Belt at 1524mm length] || 6&nbsp;mm || 2.00 mm || 1524 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/universal-gt2-belts-pulleys-kit-for-reprap-other-3d-printers-11954 Universal Kit for RepRap/Other 3D Printers] || 6 mm || 2.00 mm || 1032 & 1164 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-reprap-prusa-11950 Kit for RepRap Prusa] || 6 mm || 2.00 mm || 900 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-delta-robot-11953 Kit for Rostock Delta Robot] || 6 mm || 2.00 mm || 1524 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-mini-11952 Kit for Rostock Mini] || 6&nbsp;mm || 2.00 mm || 1032 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Charlie's 3D Technologies || BE || [http://www.charlies3dtechnologies.eu/GT2_Belt_1_m/p1675911_9494987.aspx Belt] || 6 mm || 2.03 mm || 1000 mm || &nbsp;<br />
|-<br />
| Cubic-Print || DE || [http://www.cubic-print.de GT2 Belt kit] || 6 mm || 2.00 mm || cut to length || &nbsp;<br />
|-<br />
| eBay: fabster3d || CN || [http://www.ebay.com/sch/fabster3d/m.html Belt] || 6 mm || &nbsp; || 974-1164 mm || &nbsp;<br />
|-<br />
| eBay: yellowvirtualsales || US || [http://www.ebay.com/sch/yellowvirtualsales/m.html Precision GT2 Belt] || 6 mm || 2.00 mm || Cut To Length || &nbsp;<br />
|-<br />
| EmotionTech || FR || [http://www.reprap-france.com/68-kit-de-courroies-gt2.html Belt] || 6 mm || 2.00 mm || 850 mm || &nbsp;<br />
|-<br />
| Fabberworld || CH || [http://www.fabberworld.com/Pulleys-and-Timing-Belts/GT2-Timing-Belt-by-the-meter::39.html Belt] || 6 mm || 2.00 mm || 1000+ mm || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=74 Kit for RepRap Prusa 2] || 6 mm || &nbsp; || 976 mm x 3 || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=75 Kit for Rostock Mini] || 6 mm || &nbsp; || 900 mm x 3 || &nbsp;<br />
|-<br />
| Makemendel || IN|| [http://makemendel.com/mechanical-parts/mechanical-parts-1/pulleys-and-belts/gt2-open-belt GT2 Belt] || 7 mm || 2.00 mm || 1000 mm and more || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302190510/ 2GT Belt] || 4 mm || 2.00 mm || 662-9942 mm || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302190510/ 2GT Belt] || 6 mm || 2.00 mm || 662-9942 mm || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302190510/ 2GT Belt] || 9 mm || 2.00 mm || 662-9942 mm || &nbsp;<br />
|-<br />
| ReprapWorld.com || EU || [http://reprapworld.com/?searchresults&cPath=1655] || 6 mm || 2.00 mm || 1000-75000 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/38/Closed-loop-GT2-Belt,-101-Teeth-202mm-Long 202mm Closed-loop GT2 Belt] || 6 mm || 2.00 mm || 202 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/48/760mm-380-teeth-Closed-loop-6mm-Width-GT2-Belt 760mm Closed-loop GT2 Belt] || 6 mm || 2.00 mm || 760 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/160/1524mm-long-762-teeth-closed-loop-gt2-belt-for-rostock 1524mm Endless GT2 Belt] || 6 mm || 2.00 mm || 1524 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/10/Open-Ended-6mm-Width-GT2-Belt GT2 Belt Open Ended] || 6 mm || 2.00 mm || 1000-50000 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/22/MXL-Belt,-6mm-Width-Open-Ended MXL Belt] || 6 mm || 2.00 mm || 1000-50000 mm || &nbsp;<br />
|-<br />
| RoyalSupply || US || [http://www.royalsupply.com/store/pc/Gates-2MR-1164-06-PowerGrip-GT2-V-Belt-2MR-and-3MR-93901582-1036p17193.htm#details Belt] || 6 mm || 2.00 mm || 1164 mm || &nbsp;<br />
|-<br />
| TechPaladin Printing || US || [http://techpaladin.com/store/#!/~/product/id=9001827 Belt] || 6 mm || 2.00 mm || 1380 mm || &nbsp;<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || ES || [http://store.thingibox.com/en/powertransmission/7-gt2_timing_belt.html GT2 Belt] || 5 or 6 mm || 2.00 mm || Any || Worldwide shipping<br />
|-<br />
|[http://www.TriDPrinting.com/ TriDPrinting.com]|| US || [http://www.TriDPrinting.com/Mechanical-Parts/ GT2 Belt Open Ended] || 6 mm || 2.00 mm || 1000-50000 mm || Worldwide Delivery;<br />
|-<br />
| Ultibots || US || [http://www.ultibots.com/gt2-timing-belt-1164mm/ Belt] || 6 mm || 2.00 mm || 1164 mm || &nbsp;<br />
|}<br />
<br />
<br />
<br />
There is also some on ebay.<br />
<br />
*beside GT2 belts, there is also 2M that have a 2mm round pitch (like [http://www.powerdrive-belt.com/new/products.asp?x=1&id=16&id2=69&id4=2&t=1] and many other suppliers)<br />
<br />
==Pulleys==<br />
<br />
See also [[GT2 Timing Belt]].<br />
<br />
{| class="wikitable sortable"<br />
|+ <br />
|- style="background-color:#f0f0f0;"<br />
! Supplier !! From !! Type available !! Pitch !! Tooth !! Size (bore, OD,...) !! Max belt width !! Material !! Additional notes <br />
|-<br />
| [http://www.3distributed.com/products/gt2-pulley 3Distributed] || UK || GT2 || 2mm || 20 || 5mm || 6mm || Aluminium with grub screws || Delivers Worldwide<br />
|-<br />
| [http://www.think3dprint3d.com/Hardware/t2.5-16-ToothTimingPulley-M4GrubScrews Think3DPrint3D] || UK || T2.5 || 2.5 mm || 16 || 5 mm || 7 mm || Aluminum with zinc plated steel flanges|| fast delivery and excellent customer service!<br />
|-<br />
| [http://www.robotdigg.com/category/9/Timing-Pulley&Belt 3DCracker&RobotDigg] || CN || GT2 || 2 mm || 16, 20, 36 || 5 mm or 8mm || 7 mm || All Aluminum || -<br />
|-<br />
| [http://www.3dmakerworld.com 3DMakerWorld] || US || GT2 || 2 mm || 20 & 36 || 5 mm || 6 mm || Aluminium & Polycarbonate with brass insert || -<br />
|-<br />
| [http://reprapuniverse.com/catalog/product_info.php?products_id=68 ReprapUniverse.com] || Netherlands || T2.5 || 2.5mm || 16 || 5 mm || 6 mm || Aluminum + M3 grub screws || Quality Aluminum Pulleys. Perfect for Reprap 3D Printers: Prusa Mendel i2, Prusa i3, MendelMax 1.5 & others. Cheap International Shipping.<br />
|-<br />
| [http://www.charlies3dtechnologies.eu/Belts_and_Pulleys/cat1675912_1594189.aspx Charlie's 3D Technologies] || Belgium || MXL and GT2 || - || 15 or 20 || -|| - || - || -<br />
|-<br />
| [http://www.cubic-print.com Cubic Print] || Germany || T2.5 <BR> T5 || 2.5mm <BR> 5 mm || 8, 16 || 5 mm || 7 mm || alu + steel grub screws || -<br />
|-<br />
| [http://www.bbman.com/ BBMan] || US || many<br />
|-<br />
| [http://www.beltingonline.com/timing-pulleys-272/ Belting Online] || UK || GT2, T2.5, T5 & MXL || 2mm, 2.5mm, 2.03mm & 5mm ||16, 18, 20, 36 <BR> Also Special Made to order if required || 5mm <BR> Specials sizes are possible. || 6mm || Alu + Grub Screws || Quality Pulleys Manufactured in the UK. <br />
|-<br />
| [http://www.econobelt.com/e-store/Pulleys.htm Econobelt] || US || many<br />
|-<br />
| [http://www.ebay.com/sch/m.html?_odkw=&item=181168182751&pt=BI_Heavy_Equipment_Parts&_osacat=0&hash=item2a2e7715df&_ssn=yellowvirtualsales&_trksid=p2046732.m570.l1313&_nkw=pulley&_sacat=0&_from=R40 eBay: Yellowvirtualsales] || USA || GT2, HDT3M || 2MM / 3MM|| 12-36 || 5 mm || 6-10MM mm || Fiberglass Reinforced || Fast Worldwide Shipping<br />
|-<br />
| [https://www.inventables.com/categories/frame-rail/pulleys Inventables] || US|| MXL || - || - || - || - || - || - <br />
|-<br />
| [http://makemendel.com/mechanical-parts/t2-5-pulley MakeMendel] || India || GT2 <BR> T2.5 || 2 <BR> 2.5 mm || 20 <BR> 12 or 16 || 5 mm || 7mm || Aluminium with grub screws || T2.5 pulley is available in 12 teeth and 16 teeth as well. Suitable for all 3D printers. Shipping is worldwide<br />
|-<br />
| [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1097 Misumi] || multiple<br />
|-<br />
| [http://www.paoparts.com/fr/15-courroies Paoparts] || France || T2,5 <br> T5<br />
|-<br />
| [http://reprapworld.com/?products_details&products_id=247 RepRapWorld] || Netherlands || T5 || 5 mm || 8 || 5 mm x 17 mm x 20 mm || ? || Alu || Pulley profile has play resulting in lash when reversing<br />
|-|-<br />
| [http://www.robotdigg.com/ RobotDigg] || China || [http://www.robotdigg.com/category/9/Timing-Pulley&Belt GT2], T2.5 and MXL || 2mm, 2.5mm, 2.03mm || 16, 18, 20, 36 || 5*17.5*18 mm || 7mm || Alu || SKYPE: robotdigg<br />
|-<br />
| [http://www.royalsupply.com/store/pc/Gates-2MR-18S-06-PowerGrip-GT2-Sprockets-2MR-and-3MR-78426007-1555p42023.htm#details Royal Supply] || US || GT2 || 2 mm || 18 || 4,7 mm || 6 mm || Alu || you'll need to redrill the bore (3/16") to fit usual 5 mm motor shaft<br />
|-<br />
| [https://sdp-si.com SDP-SI] || US || many<br />
|-<br />
| [http://techpaladin.com/store/#ecwid:category=1941327&mode=product&product=9188440 TechPaladin] || US || GT2 || 2 mm || 36 || 5 mm || 6 mm || plastic/bronze || -<br />
|-<br />
| [http://www.TriDPrinting.com/Mechanical-Parts/ TriDPrinting.com] || US || GT2 || 2 mm || 16, 20 || 5 mm || 6 mm || Aluminium with grub screws || Uses two set screws, Worldwide Delivery<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || Spain || GT2 || 2 mm || 16 || 5 mm || 4-6 mm || Aluminium + grub screws || Worldwide shipping<br />
|-<br />
| [http://ultimachine.com/content/timing-pulley-gt2-20-tooth Ultimachine] || US || GT2 || 2 mm || 20 || 5 mm || 6 mm || Alu || use two set screws<br />
|-<br />
| [http://RepRap-India.com RepRap-India.com] || US || GT2 || 2 mm || 20 || 5 mm || 6 mm || Alu || use two set screws<br />
|-<br />
| [http://RepRap-India.com RepRap-India.com] || US || T2.5 || 2 mm || 20 || 5 mm || 6 mm || Alu || use two set screws<br />
|-<br />
<br />
|}<br />
<br />
<br />
<br />
{| class="wikitable sortable"<br />
|- style="background-color:#f0f0f0;"<br />
! Vendor !! Loc. !! Product !! Material !! Belt width !! Bore !! Tooth !! Flange !! class="unsortable" | Additional notes<br />
|-<br />
| 3D Acessories Hub || IN || [http://www.3dacessorieshub.com GT2 Pulley] || Aluminium || 7 mm || 5.00 mm || 20 || - || &nbsp;<br />
|-<br />
| 3DCracker || CN || [http://www.3dcracker.com GT2 Pulley] || &nbsp; || 7 mm || 5, 8mm || 16, 20, 36 || double || &nbsp;<br />
|-<br />
| eBay: Yellowvirtualsales|| US || [http://www.ebay.com/sch/m.html?_odkw=gt2&_osacat=0&_from=R40&_ssn=yellowvirtualsales&_trksid=p2046732.m570.l1313.TR11.TRC1.A0.Xpulley.TRS0&_nkw=pulley&_sacat=0 Timing Pulleys] || Aluminum, Metal || 6mm - 10mm || 5.00 mm || 12-36 || Vary || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/collections/frontpage/products/gt2-pulley Pulley] || &nbsp; || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/xy-gt2-timing-belt-pulley-kit-1 Prusa Kit] || &nbsp; || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/d-gt2-timing-belt-pulley-kit Rostock/Delta Kit] || &nbsp; || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| 3DMakerWorld || US || [http://www.3dmakerworld.com/store/parts-accessories/hardware GT2 Timing Pulley] || Aluminium & Polycarbonate with brass insert || 6 mm || 5.00 mm || 20 & 36 || double || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_pulley Pulley] || Aluminium || 3 mm || 5.00 mm || 12-20 || double || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_pulley Pulley] || Aluminium || 6 mm || 5.00 mm || 12-20 || double || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_pulley Pulley] || Aluminium || 9 mm || 5.00 mm || 12-20 || double || &nbsp;<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-pitch-pulley-20-tooth-c-w-5mm-h7-bore-2-x-m3-g-s-11970 Separate Timing Pulley (sold each)] || Aluminium || 6 mm || 5.00 mm || 20 || double || UK Manufactured Precision Pulley<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/universal-gt2-belts-pulleys-kit-for-reprap-other-3d-printers-11954 Universal Kit for RepRap/Other 3D Printers] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-reprap-prusa-11950 Kit for RepRap Prusa] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-delta-robot-11953 Kit for Rostock Delta Robot] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-mini-11952 Kit for Rostock Mini] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Charlie's 3D Technologies || BE || [http://www.charlies3dtechnologies.eu/GT2_Pulley_Deluxe_1_pcs/p1675911_9495003.aspx Pulley] || Aluminium, nylon || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Charlie's 3D Technologies || BE || [http://www.charlies3dtechnologies.eu/GT2_Alu_Pulley_Deluxe_1_pcs/p1675911_9652574.aspx Pulley] || Aluminium || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Cubic-Print || DE || [http://www.cubic-print.com Pulley / Kit] || Aluminium || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| eBay: fabster3d || CN || [http://www.ebay.com/sch/fabster3d/m.html Pulley] || Aluminium (black) || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| EmotionTech || FR || [http://www.reprap-france.com/69-poulie-gt2.html Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Fabberworld || CH || [http://www.fabberworld.com/Pulleys-and-Timing-Belts/GT2-Pulley-20-Tooth-Aluminium::40.html Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=74 Kit for RepRap Prusa 2] || Aluminium (black) || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=75 Kit for Rostock Mini] || Aluminium (black) || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Makemendel || IN || [http://makemendel.com/mechanical-parts/mechanical-parts-1/gt2-pulley GT2 Pulley] || Aluminium || 7 mm || 5.00 mm || 20 || - || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302193470/ 2GT Pulley] || Aluminium || 4 mm || 5.00 mm || 32 || double || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302193470/ 2GT Pulley] || Aluminium || 6 mm || 5.00 mm || 32 || double || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302193470/ 2GT Pulley] || Aluminium || 9 mm || 5.00 mm || 32 || double || &nbsp;<br />
|-<br />
| Misumi || Japan || [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=metric2010&page=1095 Misumi's pulley introduction] || ? || ? || ? || ? || ?<br />
|<br />
Another good source for GT2 pulleys and belts is Misumi. They carry a huge variety of suitable pulleys, including several that are closer to out ideal diameter. In addition, Misumi has offices around the globe so they are a better choice for international customers (though some regions will only sell to businesses).<br />
<br />
Their website does not make it easy to browse for belts and pulleys, but here are the relevent pages in their catalog:<br />
<br />
* [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1097 Pulleys]<br />
* [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1175 Belts]<br />
* [http://www.sdp-si.com/D265/HTML/D265T003.html Handbook of Timing Belts and Pulleys]<br />
<br />
Note: Misumi calls theirs 2GT (2mm pitch) and 3GT (3mm pitch). As far as I know they are compatible with GT2, but both offer the same benefits. Misumi's pulleys seem expensive, but they are metal pulleys. We don't really need metal pulleys for our needs, but they are fine.<br />
<br />
<br />
|-<br />
| ReprapWorld.com || EU || [http://reprapworld.com/?searchresults&cPath=1655 Multiple types of Pulley] || Aluminium || 5-6 mm || 5mm || Multiple || double || &nbsp;<br />
|-<br />
| [http://www.robotdigg.com/ Robotdigg] || CN || [http://www.robotdigg.com/product/59/Rostock-16-Teeth-5mm-Bore-GT2-Pulley 16Teeth 2GT Pulley] || Aluminium || 7 mm || 5mm, 8mm || 16 || double || &nbsp;<br />
|-<br />
| [http://www.robotdigg.com/ Robotdigg] || CN || [http://www.robotdigg.com/product/9/GT2-Pulley-20-Teeth-5mm-Bore GT2 Pulley] || Aluminium || 7 mm || 5mm, 8mm || 20 || double || &nbsp;<br />
|-<br />
| [http://www.robotdigg.com/ Robotdigg] || CN || [http://www.robotdigg.com/product/24/GT2-Pulley-36-Teeth-5mm-Bore GT2 Pulley] || Aluminium || 7 mm || 5mm || 36 || double || &nbsp;<br />
|-<br />
| RoyalSupply || US || [http://www.royalsupply.com/store/pc/Gates-2MR-18S-06-PowerGrip-GT2-Sprockets-2MR-and-3MR-78426007-1555p42023.htm#details Pulley] || Aluminium || 4-6 mm || 4.76 mm || 18 || double || You'll need to redrill them to fit on the usual 5mm motor shaft<br />
|-<br />
| Stock Drive Products || US || https://sdp-si.com/ || &nbsp; || &nbsp; || 5.00 mm || [https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=22736&GroupID=347 36], [https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=8545&GroupID=347 40], [https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=55836&GroupID=347 42] || &nbsp;<br />
| In the US, a popular source is SDP/SI. They sell a huge variety of belts and pulleys that meet our needs. Always call SDP/SI for stock, their website is always out of date.<br />
<br />
* [https://sdp-si.com/eStore/Direct.asp?GroupID=347 Pulleys (bad link)]<br />Filter for GT2, 2mm pitch, then choose the bore size needed for your steppers.<br />
* [https://sdp-si.com/eStore/Direct.asp?GroupID=342 Belts (bad link)]<br />Filter on GT2, 2mm Pitch, and get 2 belts as close to 1m long as possible.<br />
<br />
Note, unfortunately, SDP/SI does not carry a smaller diameter GT2 pulley with a 5mm bore, so to buy your pulleys here you need a larger pulley than in strictly ideal. These are fine, though. I ([[User:Virtlink|Virtlink]] ?) use the 36 tooth pulleys on my printer and they work great.<br />
|-<br />
| TechPaladin Printing || US || [http://techpaladin.com/store/#!/~/product/category=1941327&id=18833859 Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || ES || [http://store.thingibox.com/en/powertransmission/8-pulleys.html GT2 Pulley] || Aluminium || 4-6 mm || 5.00 mm || 16 || double || Length: 7mm; Worldwide shipping<br />
|-<br />
| [http://www.TriDPrinting.com/ TriDPrinting.com] || US || [http://www.TriDPrinting.com/Mechanical-Parts/ GT2 Pulley] || Aluminium || 6 mm || 5.00 mm || 16, 20 || double || Worldwide Delivery<br />
|-<br />
| Ultibots || US || [http://www.ultibots.com/gt2-timing-pulley-20-tooth/ Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| UltiMachine || US || [https://ultimachine.com/content/timing-pulley-gt2-20-tooth Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|}<br />
<br />
=== RobotDigg ===<br />
China manufacturer of T2.5 pulley, MXL pulley, GT2 pulleys. T2.5 belt, MXL belt and GT2 belt in different width, open ended and endless or closed-loop timing belt provider.<br />
T2.5 pulley 16 tooth 5mm bore<br />
T5 pulley 12 tooth 8mm bore<br />
MXL pulley 18 teeth 5mm bore<br />
MXL pulley 20 teeth 6.35mm bore<br />
MXL pulley 36 teeth 5mm bore<br />
MXL pulley 36 teeth 8mm bore<br />
GT2 pulley 16 teeth 5mm bore<br />
GT2 pulley 18 tooth 6.35mm bore<br />
GT2 pulley 20 teeth 5mm, 6.35mm bore and 8mm bore<br />
GT2 pulley 32 tooth 10mm bore<br />
GT2 pulley 36 teeth 5mm bore and 8mm bore<br />
GT2 pulley 40 tooth 5mm, 6.35mm 8mm bore n 10mm bore<br />
* [http://www.robotdigg.com/product/25/T2.5-pulley,-16-teeth,-5mm-bore T2.5 pulley, 16 tooth, 5mm bore]<br />
* [http://www.robotdigg.com/product/26/MXL-pulley,-18-tooth,-5mm-bore MXL pulley 18 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/147/36-Tooth-MXL-Pulley-with-5mm-Bore MXL pulley 36 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/148/36-Tooth-MXL-Pulley-with-8mm-Bore MXL pulley 36 teeth, 8mm bore]<br />
* [http://www.robotdigg.com/product/59/Rostock-16-Teeth-5mm-Bore-GT2-Pulley 2GT pulley 16 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/9/GT2-Pulley-20-Teeth-5mm-Bore 2GT pulley 20 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/23/GT2-Pulley-20-Teeth-8mm-Bore 2GT pulley 20 teeth, 8mm bore]<br />
* [http://www.robotdigg.com/product/149/10mm-bore-32-teeth-gt2-pulley GT2 pulley 32 tooth 10mm bore]<br />
* [http://www.robotdigg.com/product/24/GT2-Pulley-36-Teeth-5mm-Bore 2GT pulley 36 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/66/2gt-pulley-36-teeth-8mm-bore 2GT pulley 36 teeth, 8mm bore]<br />
* [http://www.robotdigg.com/product/116/2gt-pulley-40-teeth-5mm-bore 2GT pulley 40 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/66/2gt-pulley-36-teeth-8mm-bore 2GT pulley 40 teeth, 6.35mm bore]<br />
* [http://www.robotdigg.com/product/146/GT2-40-Tooth-8mm-Bore-Pulley 2GTpulley 40 teeth, 8mm bore]<br />
MOQ 50pcs for Custom Pulleys.<br />
<br />
== Cable ==<br />
*Synchromesh<br />
**https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=5503&GroupID=312<br />
**https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=84751&GroupID=768</div>Merlucinhttps://reprap.org/mediawiki/index.php?title=Belts_and_Pulleys&diff=124682Belts and Pulleys2014-05-02T08:45:36Z<p>Merlucin: /* Belts */</p>
<hr />
<div>{{Merge|GT2_Timing_Belt}}<br />
[[Category:Suppliers_by_Part]]<br />
<br />
See also [[Choosing_Belts_and_Pulleys]]<br />
<br />
==Belts==<br />
<br />
See also [[GT2 Timing Belt]]<br />
<br />
{| class="wikitable sortable"<br />
|+ <br />
|- style="background-color:#f0f0f0;"<br />
! Supplier !! From !! Type available !! Pitch !! Width !! Length !! Material !! Additional notes <br />
|-<br />
| [http://www.3distributed.com/collections/frontpage/products/gt2-timing-belt 3Distributed] || UK || GT2 || 2mm || 6mm || Sold by the metre || Fiberglass reinforced neoprene rubber. || Delivers Worldwide <br />
|-<br />
| [http://www.think3dprint3d.com/Hardware Think3DPrint3D] || UK || GT2, T2.5 || 2 mm, 2.5 mm || 6 mm || sold by the meter || fiberglass reinforced rubber, steel-reinforced polyurethane|| fast world-wide delivery and excellent customer service<br />
|-<br />
|[http://3dacessorieshub.com/ 3D Acessories Hub] || India || GT2 <BR> T2.5 || 2 mm <BR> 2 mm || 660mm closed <BR> as per your requirement || || Rubber <BR> <br />
polyurethane || -<br />
|-<br />
|[http://3dprinterczar.com/shop/hardware/gt2-pulley-belt/ 3D Printer Czar] || US || GT2 || 2 mm || 6 mm || at your choice|| Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://www.robotdigg.com/category/9/Timing-Pulley&Belt 3DCracker] || CN ||[http://www.robotdigg.com/category/9/Timing-Pulley&Belt GT2] || 2 mm || 6 mm || 900mm, 976mm, 1220mm, 1350mm|New-add '''1524mm closed-loop''', etc and open ended || Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://www.reprap.cn/ He3D] || CN || GT2, MXL, T2.5, T5 || 2.5 mm || 6 mm || 1350mm 990mm and open ended || Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://reprapuniverse.com/catalog/product_info.php?cPath=30_73&products_id=67 ReprapUniverse.com] || Netherlands || T2.5 || 2.5 mm || 5 mm || sold by the meter || Open ended Neoprene Rubber with Fiberglass Reinforced|| Perfect timing belt for Prusa Mendel i2, Prusa i3, MendelMax 1.5. Cheap International Shipping.<br />
|-<br />
| [http://www.3dmakerworld.com 3DMakerWorld] || US || GT2 || 2 mm || 6 mm || 1164 mm || Neoprene, fiberglass reinforced || -<br />
|-<br />
| [http://www.charlies3dtechnologies.eu/Belts_and_Pulleys/cat1675912_1594189.aspx Charlie's 3D Technologies] || Belgium || MXL and GT2 || - || - || - || - || -<br />
|-<br />
| [http://www.cubic-print.com Cubic Print] || Germany || T2.5 <BR> T5 || 2.5 mm <BR> 5 mm|| 6 mm || as you wish || PU + steel || open belts<br />
|-<br />
| [http://www.bbman.com/ BBMan] || US || Imperial/Metric<br />
|-<br />
| [http://www.beltingonline.com/ Belting Online] || UK || GT2, MXL, T2.5, T5 || 2 mm 2.5 & 5mm|| As you wish || As you wish|| PU & Neoprene Rubber || Genuine Branded Quality Products <br />
|-<br />
<br />
| [http://easyreprap.com/shop/article_19/GT2-Belt-_-Pulley-Set.html Easy RepRap] || USA ||Precision GT2 || 2 mm || 6 mm || 1150mm || Fiberglass Reinforced || GT2 Belt/Pulley Sets<br />
|-<br />
<br />
| [http://www.ebay.com/sch/yellowvirtualsales/m.html eBay: Yellowvirtualsales] || USA ||Precision GT2 || 2 mm || 6 mm || Cut To Length || Fiberglass Reinforced || Fast Worldwide Shipping<br />
|-<br />
| [http://www.econobelt.com/Timing_Belts.htm Econobelt] || US || many<br />
|-<br />
| [http://www.timing-belt-manufacturer.com/contact.html Eke] || China || many<br />
|-<br />
| [http://www.indiamart.com/bm-beltings-company/industrial-belts.html#open-end-polyurethane Indiamart] || India || many<br />
|-<br />
| [https://www.inventables.com/categories/frame-rail/belting Inventables] || US|| MXL || - || - || 1 foot increments || - || -<br />
|-<br />
| [http://www.kainabelt.com KainaBelt] || China || many<br />
|-<br />
| [http://makemendel.com/mechanical-parts/t2-5-timing-belt Makemendel] || India || GT2 <BR> T2.5 || 2mm <BR> 2.5 mm || 7 mm <BR> 7mm || Open Belt || PU || Open Belts for all Reprap and other 3D printers. Available in custom length.<br />
|-<br />
| [http://www.megadyne.it/ Megadyne] || Italy || many<br />
|-<br />
| [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1175 Misumi] || multiple<br />
|-<br />
| [http://www.paoparts.com/fr/15-courroies Paoparts] || France || T2.5 <br> T5 || 2,5mm <br> 5mm || 5mm || - || PU ||<br />
|-<br />
| [http://shop.polybelt.com/Metirc-Pitch-Open-End-Belt-Roll_c29.htm PolyBelt] || US || T2.5 <br> T5 || 5 mm || 6 mm || - || polyurethane + steel || -<br />
|-<br />
| [http://reprapworld.com/?searchresults&cPath=1595_1611 RepRapWorld] || Netherlands || T2.5 <br> T5 || 2,5 mm <br> 5 mm || 5 mm <br> 5 mm || 1 m || neoprene<br>polyurethane + steel || -<br />
|-<br />
| [http://www.robotdigg.com RobotDigg] || China || [http://www.robotdigg.com/product/10/Open-Ended-6mm-Width-GT2-Belt GT2], MXL, T2.5 || 2 mm || 6mm, 6.35mm or 9mm || 20M or 50M per roll ,[http://www.robotdigg.com/product/38/Closed-loop-GT2-Belt,-101-Teeth-202mm-Long Closed-loop GT2]|| Neoprene Rubber, Fiberglass Reinforced. MOQ 50M<br />
|<br />
|-<br />
| [http://www.royalsupply.com/store/pc/Gates-2MR-1164-06-PowerGrip-GT2-V-Belt-2MR-and-3MR-93901582-1036p17193.htm Royal supply] || US || GT2 || 2 mm || 6 mm || 1164 mm || fiberglass / nylon / neoprene || -<br />
|-<br />
| [https://sdp-si.com SDP-SI] || US || Imperial/Metric<br />
|-<br />
| [http://techpaladin.com/store/#ecwid:category=1941327&mode=product&product=9001827 TechPaladin] || US || GT2 || 2 mm || 5 mm || 1160 mm || neoprene || -<br />
|-<br />
| [http://www.tanals.com/fr/courroies-dentees-neoprene/ Tanals] || France || many || - || - || - || - || don't sell to individuals<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || Spain || GT2 || 2mm || 5 mm || 1 m || Neoprene Rubber || Worldwide shipping<br />
|-<br />
| [http://www.tridprinting.com/Mechanical-Parts/ TriDPrinting.com] || US || GT2 || 2 mm || 6 mm || Sold by the meter, open ended || Neoprene, Fiberglass Reinforced || 50 m max, Worldwide Delivery<br />
|-<br />
| [http://www.RepRap-India.com RepRap-India.com] || IN || GT2 || 2 mm || 6 mm || open ended || Neoprene, fiberglass reinforced || 50 m max<br />
|-<br />
|}<br />
<br />
<br />
<br />
{| class="wikitable sortable"<br />
|- style="background-color:#f0f0f0;"<br />
! Vendor !! Loc. !! Product !! Width !! Pitch !! Length !! class="unsortable" | Additional notes<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/collections/frontpage/products/gt2-timing-belt GT2 Belt] || 6mm || 2.00mm || Multiples of 1000mm || &nbsp;<br />
|-<br />
| Think3DPrint3D || UK || [http://www.think3dprint3d.com/Hardware/GT2-Timing-Belt GT2 Belt] || 6 mm || 2.00 mm || multiples of 1000 mm || &nbsp;<br />
|-<br />
| 3D Acessories Hub || IN|| [http://www.3dacessorieshub.com GT2 Belt] || 7 mm || 2.00 mm || 660 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ 3DCracker&RobotDigg]|| CN || [http://www.robotdigg.com/product/160/1524mm-long-762-teeth-closed-loop-gt2-belt-for-rostock 1524mm Endless GT2 Belt] || 6 mm || 2.00 mm || 1524 mm || &nbsp;<br />
|-<br />
| 3DCracker || CN || [http://www.3dcracker.com GT2 Belt] || 6 mm || 2.00 mm || Open ended and closed-loop || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/xy-gt2-timing-belt-pulley-kit-1 Prusa Kit] || 6 mm || 2.00 mm || 1000 mm || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/d-gt2-timing-belt-pulley-kit Rostock/Delta Kit] || 6 mm || 2.00 mm || 1000 mm || &nbsp;<br />
|-<br />
| 3DMakerWorld || US || [http://www.3dmakerworld.com/store/parts-accessories/hardware/gt2-timing-belt Belt] || 6 mm || 2.00 mm || 1164 mm || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_belts Belt] || 3 mm || 2.00 mm || 54-1910 mm || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_belts Belt] || 6 mm || 2.00 mm || 54-1910 mm || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_belts Belt] || 9 mm || 2.00 mm || 54-1910 mm || &nbsp;<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-900mm-x-6mm-450-teeth-11958 Separate Belt at 900mm length] || 6&nbsp;mm || 2.00 mm || 900 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-976mm-x-6mm-488-teeth-11959 Separate Belt at 976mm length] || 6&nbsp;mm || 2.00 mm || 976 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1032mm-x-6mm-516-teeth-12179 Separate Belt at 1032mm length] || 6&nbsp;mm || 2.00 mm || 1032 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1164mm-x-6mm-582-teeth-11960 Separate Belt at 1164mm length] || 6&nbsp;mm || 2.00 mm || 1164 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1386mm-x-6mm-693-teeth-12181 Separate Belt at 1386mm length] || 6&nbsp;mm || 2.00 mm || 1386 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-timing-belt-1524mm-x-6mm-762-teeth-12180 Separate Belt at 1524mm length] || 6&nbsp;mm || 2.00 mm || 1524 mm || Genuine Gates/Unitta GT2 belting.<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/universal-gt2-belts-pulleys-kit-for-reprap-other-3d-printers-11954 Universal Kit for RepRap/Other 3D Printers] || 6 mm || 2.00 mm || 1032 & 1164 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-reprap-prusa-11950 Kit for RepRap Prusa] || 6 mm || 2.00 mm || 900 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-delta-robot-11953 Kit for Rostock Delta Robot] || 6 mm || 2.00 mm || 1524 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-mini-11952 Kit for Rostock Mini] || 6&nbsp;mm || 2.00 mm || 1032 mm || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Charlie's 3D Technologies || BE || [http://www.charlies3dtechnologies.eu/GT2_Belt_1_m/p1675911_9494987.aspx Belt] || 6 mm || 2.03 mm || 1000 mm || &nbsp;<br />
|-<br />
| Cubic-Print || DE || [http://www.cubic-print.de GT2 Belt kit] || 6 mm || 2.00 mm || cut to length || &nbsp;<br />
|-<br />
| eBay: fabster3d || CN || [http://www.ebay.com/sch/fabster3d/m.html Belt] || 6 mm || &nbsp; || 974-1164 mm || &nbsp;<br />
|-<br />
| eBay: yellowvirtualsales || US || [http://www.ebay.com/sch/yellowvirtualsales/m.html Precision GT2 Belt] || 6 mm || 2.00 mm || Cut To Length || &nbsp;<br />
|-<br />
| EmotionTech || FR || [http://www.reprap-france.com/68-kit-de-courroies-gt2.html Belt] || 6 mm || 2.00 mm || 850 mm || &nbsp;<br />
|-<br />
| Fabberworld || CH || [http://www.fabberworld.com/Pulleys-and-Timing-Belts/GT2-Timing-Belt-by-the-meter::39.html Belt] || 6 mm || 2.00 mm || 1000+ mm || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=74 Kit for RepRap Prusa 2] || 6 mm || &nbsp; || 976 mm x 3 || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=75 Kit for Rostock Mini] || 6 mm || &nbsp; || 900 mm x 3 || &nbsp;<br />
|-<br />
| Makemendel || IN|| [http://makemendel.com/mechanical-parts/mechanical-parts-1/pulleys-and-belts/gt2-open-belt GT2 Belt] || 7 mm || 2.00 mm || 1000 mm and more || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302190510/ 2GT Belt] || 4 mm || 2.00 mm || 662-9942 mm || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302190510/ 2GT Belt] || 6 mm || 2.00 mm || 662-9942 mm || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302190510/ 2GT Belt] || 9 mm || 2.00 mm || 662-9942 mm || &nbsp;<br />
|-<br />
| ReprapWorld.com || EU || [http://reprapworld.com/?searchresults&cPath=1655] || 6 mm || 2.00 mm || 1000-75000 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/38/Closed-loop-GT2-Belt,-101-Teeth-202mm-Long 202mm Closed-loop GT2 Belt] || 6 mm || 2.00 mm || 202 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/48/760mm-380-teeth-Closed-loop-6mm-Width-GT2-Belt 760mm Closed-loop GT2 Belt] || 6 mm || 2.00 mm || 760 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/160/1524mm-long-762-teeth-closed-loop-gt2-belt-for-rostock 1524mm Endless GT2 Belt] || 6 mm || 2.00 mm || 1524 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/10/Open-Ended-6mm-Width-GT2-Belt GT2 Belt Open Ended] || 6 mm || 2.00 mm || 1000-50000 mm || &nbsp;<br />
|-<br />
|[http://www.robotdigg.com/ RobotDigg]|| CN || [http://www.robotdigg.com/product/22/MXL-Belt,-6mm-Width-Open-Ended MXL Belt] || 6 mm || 2.00 mm || 1000-50000 mm || &nbsp;<br />
|-<br />
| RoyalSupply || US || [http://www.royalsupply.com/store/pc/Gates-2MR-1164-06-PowerGrip-GT2-V-Belt-2MR-and-3MR-93901582-1036p17193.htm#details Belt] || 6 mm || 2.00 mm || 1164 mm || &nbsp;<br />
|-<br />
| TechPaladin Printing || US || [http://techpaladin.com/store/#!/~/product/id=9001827 Belt] || 6 mm || 2.00 mm || 1380 mm || &nbsp;<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || ES || [http://store.thingibox.com/en/powertransmission/7-gt2_timing_belt.html GT2 Belt] || 5 or 6 mm || 2.00 mm || any || Worldwide shipping<br />
|-<br />
|[http://www.TriDPrinting.com/ TriDPrinting.com]|| US || [http://www.TriDPrinting.com/Mechanical-Parts/ GT2 Belt Open Ended] || 6 mm || 2.00 mm || 1000-50000 mm || Worldwide Delivery;<br />
|-<br />
| Ultibots || US || [http://www.ultibots.com/gt2-timing-belt-1164mm/ Belt] || 6 mm || 2.00 mm || 1164 mm || &nbsp;<br />
|}<br />
<br />
<br />
<br />
There is also some on ebay.<br />
<br />
*beside GT2 belts, there is also 2M that have a 2mm round pitch (like [http://www.powerdrive-belt.com/new/products.asp?x=1&id=16&id2=69&id4=2&t=1] and many other suppliers)<br />
<br />
==Pulleys==<br />
<br />
See also [[GT2 Timing Belt]].<br />
<br />
{| class="wikitable sortable"<br />
|+ <br />
|- style="background-color:#f0f0f0;"<br />
! Supplier !! From !! Type available !! Pitch !! Tooth !! Size (bore, OD,...) !! Max belt width !! Material !! Additional notes <br />
|-<br />
| [http://www.3distributed.com/products/gt2-pulley 3Distributed] || UK || GT2 || 2mm || 20 || 5mm || 6mm || Aluminium with grub screws || Delivers Worldwide<br />
|-<br />
| [http://www.think3dprint3d.com/Hardware/t2.5-16-ToothTimingPulley-M4GrubScrews Think3DPrint3D] || UK || T2.5 || 2.5 mm || 16 || 5 mm || 7 mm || Aluminum with zinc plated steel flanges|| fast delivery and excellent customer service!<br />
|-<br />
| [http://www.robotdigg.com/category/9/Timing-Pulley&Belt 3DCracker&RobotDigg] || CN || GT2 || 2 mm || 16, 20, 36 || 5 mm or 8mm || 7 mm || All Aluminum || -<br />
|-<br />
| [http://www.3dmakerworld.com 3DMakerWorld] || US || GT2 || 2 mm || 20 & 36 || 5 mm || 6 mm || Aluminium & Polycarbonate with brass insert || -<br />
|-<br />
| [http://reprapuniverse.com/catalog/product_info.php?products_id=68 ReprapUniverse.com] || Netherlands || T2.5 || 2.5mm || 16 || 5 mm || 6 mm || Aluminum + M3 grub screws || Quality Aluminum Pulleys. Perfect for Reprap 3D Printers: Prusa Mendel i2, Prusa i3, MendelMax 1.5 & others. Cheap International Shipping.<br />
|-<br />
| [http://www.charlies3dtechnologies.eu/Belts_and_Pulleys/cat1675912_1594189.aspx Charlie's 3D Technologies] || Belgium || MXL and GT2 || - || 15 or 20 || -|| - || - || -<br />
|-<br />
| [http://www.cubic-print.com Cubic Print] || Germany || T2.5 <BR> T5 || 2.5mm <BR> 5 mm || 8, 16 || 5 mm || 7 mm || alu + steel grub screws || -<br />
|-<br />
| [http://www.bbman.com/ BBMan] || US || many<br />
|-<br />
| [http://www.beltingonline.com/timing-pulleys-272/ Belting Online] || UK || GT2, T2.5, T5 & MXL || 2mm, 2.5mm, 2.03mm & 5mm ||16, 18, 20, 36 <BR> Also Special Made to order if required || 5mm <BR> Specials sizes are possible. || 6mm || Alu + Grub Screws || Quality Pulleys Manufactured in the UK. <br />
|-<br />
| [http://www.econobelt.com/e-store/Pulleys.htm Econobelt] || US || many<br />
|-<br />
| [http://www.ebay.com/sch/m.html?_odkw=&item=181168182751&pt=BI_Heavy_Equipment_Parts&_osacat=0&hash=item2a2e7715df&_ssn=yellowvirtualsales&_trksid=p2046732.m570.l1313&_nkw=pulley&_sacat=0&_from=R40 eBay: Yellowvirtualsales] || USA || GT2, HDT3M || 2MM / 3MM|| 12-36 || 5 mm || 6-10MM mm || Fiberglass Reinforced || Fast Worldwide Shipping<br />
|-<br />
| [https://www.inventables.com/categories/frame-rail/pulleys Inventables] || US|| MXL || - || - || - || - || - || - <br />
|-<br />
| [http://makemendel.com/mechanical-parts/t2-5-pulley MakeMendel] || India || GT2 <BR> T2.5 || 2 <BR> 2.5 mm || 20 <BR> 12 or 16 || 5 mm || 7mm || Aluminium with grub screws || T2.5 pulley is available in 12 teeth and 16 teeth as well. Suitable for all 3D printers. Shipping is worldwide<br />
|-<br />
| [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1097 Misumi] || multiple<br />
|-<br />
| [http://www.paoparts.com/fr/15-courroies Paoparts] || France || T2,5 <br> T5<br />
|-<br />
| [http://reprapworld.com/?products_details&products_id=247 RepRapWorld] || Netherlands || T5 || 5 mm || 8 || 5 mm x 17 mm x 20 mm || ? || Alu || Pulley profile has play resulting in lash when reversing<br />
|-|-<br />
| [http://www.robotdigg.com/ RobotDigg] || China || [http://www.robotdigg.com/category/9/Timing-Pulley&Belt GT2], T2.5 and MXL || 2mm, 2.5mm, 2.03mm || 16, 18, 20, 36 || 5*17.5*18 mm || 7mm || Alu || SKYPE: robotdigg<br />
|-<br />
| [http://www.royalsupply.com/store/pc/Gates-2MR-18S-06-PowerGrip-GT2-Sprockets-2MR-and-3MR-78426007-1555p42023.htm#details Royal Supply] || US || GT2 || 2 mm || 18 || 4,7 mm || 6 mm || Alu || you'll need to redrill the bore (3/16") to fit usual 5 mm motor shaft<br />
|-<br />
| [https://sdp-si.com SDP-SI] || US || many<br />
|-<br />
| [http://techpaladin.com/store/#ecwid:category=1941327&mode=product&product=9188440 TechPaladin] || US || GT2 || 2 mm || 36 || 5 mm || 6 mm || plastic/bronze || -<br />
|-<br />
| [http://www.TriDPrinting.com/Mechanical-Parts/ TriDPrinting.com] || US || GT2 || 2 mm || 16, 20 || 5 mm || 6 mm || Aluminium with grub screws || Uses two set screws, Worldwide Delivery<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || Spain || GT2 || 2 mm || 16 || 5 mm || 4-6 mm || Aluminium + grub screws || Worldwide shipping<br />
|-<br />
| [http://ultimachine.com/content/timing-pulley-gt2-20-tooth Ultimachine] || US || GT2 || 2 mm || 20 || 5 mm || 6 mm || Alu || use two set screws<br />
|-<br />
| [http://RepRap-India.com RepRap-India.com] || US || GT2 || 2 mm || 20 || 5 mm || 6 mm || Alu || use two set screws<br />
|-<br />
| [http://RepRap-India.com RepRap-India.com] || US || T2.5 || 2 mm || 20 || 5 mm || 6 mm || Alu || use two set screws<br />
|-<br />
<br />
|}<br />
<br />
<br />
<br />
{| class="wikitable sortable"<br />
|- style="background-color:#f0f0f0;"<br />
! Vendor !! Loc. !! Product !! Material !! Belt width !! Bore !! Tooth !! Flange !! class="unsortable" | Additional notes<br />
|-<br />
| 3D Acessories Hub || IN || [http://www.3dacessorieshub.com GT2 Pulley] || Aluminium || 7 mm || 5.00 mm || 20 || - || &nbsp;<br />
|-<br />
| 3DCracker || CN || [http://www.3dcracker.com GT2 Pulley] || &nbsp; || 7 mm || 5, 8mm || 16, 20, 36 || double || &nbsp;<br />
|-<br />
| eBay: Yellowvirtualsales|| US || [http://www.ebay.com/sch/m.html?_odkw=gt2&_osacat=0&_from=R40&_ssn=yellowvirtualsales&_trksid=p2046732.m570.l1313.TR11.TRC1.A0.Xpulley.TRS0&_nkw=pulley&_sacat=0 Timing Pulleys] || Aluminum, Metal || 6mm - 10mm || 5.00 mm || 12-36 || Vary || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/collections/frontpage/products/gt2-pulley Pulley] || &nbsp; || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/xy-gt2-timing-belt-pulley-kit-1 Prusa Kit] || &nbsp; || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| 3Distributed || UK || [http://www.3distributed.com/products/d-gt2-timing-belt-pulley-kit Rostock/Delta Kit] || &nbsp; || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| 3DMakerWorld || US || [http://www.3dmakerworld.com/store/parts-accessories/hardware GT2 Timing Pulley] || Aluminium & Polycarbonate with brass insert || 6 mm || 5.00 mm || 20 & 36 || double || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_pulley Pulley] || Aluminium || 3 mm || 5.00 mm || 12-20 || double || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_pulley Pulley] || Aluminium || 6 mm || 5.00 mm || 12-20 || double || &nbsp;<br />
|-<br />
| B&B Manufacturing || US || [http://www.bbman.com/catalog/category/timing_pulley Pulley] || Aluminium || 9 mm || 5.00 mm || 12-20 || double || &nbsp;<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-2mm-pitch-pulley-20-tooth-c-w-5mm-h7-bore-2-x-m3-g-s-11970 Separate Timing Pulley (sold each)] || Aluminium || 6 mm || 5.00 mm || 20 || double || UK Manufactured Precision Pulley<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/universal-gt2-belts-pulleys-kit-for-reprap-other-3d-printers-11954 Universal Kit for RepRap/Other 3D Printers] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-reprap-prusa-11950 Kit for RepRap Prusa] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-delta-robot-11953 Kit for Rostock Delta Robot] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Beltingonline || UK || [http://www.beltingonline.com/gt2-timing-belts-pulleys-kit-for-rostock-mini-11952 Kit for Rostock Mini] || Aluminium || &nbsp; || 5.00 mm || 20 || double || Genuine Gates/Unitta GT2 belting & UK Manufactured Pulleys<br />
|-<br />
| Charlie's 3D Technologies || BE || [http://www.charlies3dtechnologies.eu/GT2_Pulley_Deluxe_1_pcs/p1675911_9495003.aspx Pulley] || Aluminium, nylon || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Charlie's 3D Technologies || BE || [http://www.charlies3dtechnologies.eu/GT2_Alu_Pulley_Deluxe_1_pcs/p1675911_9652574.aspx Pulley] || Aluminium || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Cubic-Print || DE || [http://www.cubic-print.com Pulley / Kit] || Aluminium || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| eBay: fabster3d || CN || [http://www.ebay.com/sch/fabster3d/m.html Pulley] || Aluminium (black) || 7 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| EmotionTech || FR || [http://www.reprap-france.com/69-poulie-gt2.html Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Fabberworld || CH || [http://www.fabberworld.com/Pulleys-and-Timing-Belts/GT2-Pulley-20-Tooth-Aluminium::40.html Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=74 Kit for RepRap Prusa 2] || Aluminium (black) || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Gadgets 3D || PL || [http://gadgets3d.com/index.php?route=product/product&path=62&product_id=75 Kit for Rostock Mini] || Aluminium (black) || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| Makemendel || IN || [http://makemendel.com/mechanical-parts/mechanical-parts-1/gt2-pulley GT2 Pulley] || Aluminium || 7 mm || 5.00 mm || 20 || - || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302193470/ 2GT Pulley] || Aluminium || 4 mm || 5.00 mm || 32 || double || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302193470/ 2GT Pulley] || Aluminium || 6 mm || 5.00 mm || 32 || double || &nbsp;<br />
|-<br />
| Misumi || US || [http://us.misumi-ec.com/vona2/detail/110302193470/ 2GT Pulley] || Aluminium || 9 mm || 5.00 mm || 32 || double || &nbsp;<br />
|-<br />
| Misumi || Japan || [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=metric2010&page=1095 Misumi's pulley introduction] || ? || ? || ? || ? || ?<br />
|<br />
Another good source for GT2 pulleys and belts is Misumi. They carry a huge variety of suitable pulleys, including several that are closer to out ideal diameter. In addition, Misumi has offices around the globe so they are a better choice for international customers (though some regions will only sell to businesses).<br />
<br />
Their website does not make it easy to browse for belts and pulleys, but here are the relevent pages in their catalog:<br />
<br />
* [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1097 Pulleys]<br />
* [http://us.misumi-ec.com/pdf/fa/PDFViewer.html?catalog=Metric2010&page=1175 Belts]<br />
* [http://www.sdp-si.com/D265/HTML/D265T003.html Handbook of Timing Belts and Pulleys]<br />
<br />
Note: Misumi calls theirs 2GT (2mm pitch) and 3GT (3mm pitch). As far as I know they are compatible with GT2, but both offer the same benefits. Misumi's pulleys seem expensive, but they are metal pulleys. We don't really need metal pulleys for our needs, but they are fine.<br />
<br />
<br />
|-<br />
| ReprapWorld.com || EU || [http://reprapworld.com/?searchresults&cPath=1655 Multiple types of Pulley] || Aluminium || 5-6 mm || 5mm || Multiple || double || &nbsp;<br />
|-<br />
| [http://www.robotdigg.com/ Robotdigg] || CN || [http://www.robotdigg.com/product/59/Rostock-16-Teeth-5mm-Bore-GT2-Pulley 16Teeth 2GT Pulley] || Aluminium || 7 mm || 5mm, 8mm || 16 || double || &nbsp;<br />
|-<br />
| [http://www.robotdigg.com/ Robotdigg] || CN || [http://www.robotdigg.com/product/9/GT2-Pulley-20-Teeth-5mm-Bore GT2 Pulley] || Aluminium || 7 mm || 5mm, 8mm || 20 || double || &nbsp;<br />
|-<br />
| [http://www.robotdigg.com/ Robotdigg] || CN || [http://www.robotdigg.com/product/24/GT2-Pulley-36-Teeth-5mm-Bore GT2 Pulley] || Aluminium || 7 mm || 5mm || 36 || double || &nbsp;<br />
|-<br />
| RoyalSupply || US || [http://www.royalsupply.com/store/pc/Gates-2MR-18S-06-PowerGrip-GT2-Sprockets-2MR-and-3MR-78426007-1555p42023.htm#details Pulley] || Aluminium || 4-6 mm || 4.76 mm || 18 || double || You'll need to redrill them to fit on the usual 5mm motor shaft<br />
|-<br />
| Stock Drive Products || US || https://sdp-si.com/ || &nbsp; || &nbsp; || 5.00 mm || [https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=22736&GroupID=347 36], [https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=8545&GroupID=347 40], [https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=55836&GroupID=347 42] || &nbsp;<br />
| In the US, a popular source is SDP/SI. They sell a huge variety of belts and pulleys that meet our needs. Always call SDP/SI for stock, their website is always out of date.<br />
<br />
* [https://sdp-si.com/eStore/Direct.asp?GroupID=347 Pulleys (bad link)]<br />Filter for GT2, 2mm pitch, then choose the bore size needed for your steppers.<br />
* [https://sdp-si.com/eStore/Direct.asp?GroupID=342 Belts (bad link)]<br />Filter on GT2, 2mm Pitch, and get 2 belts as close to 1m long as possible.<br />
<br />
Note, unfortunately, SDP/SI does not carry a smaller diameter GT2 pulley with a 5mm bore, so to buy your pulleys here you need a larger pulley than in strictly ideal. These are fine, though. I ([[User:Virtlink|Virtlink]] ?) use the 36 tooth pulleys on my printer and they work great.<br />
|-<br />
| TechPaladin Printing || US || [http://techpaladin.com/store/#!/~/product/category=1941327&id=18833859 Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| [http://store.thingibox.com/en/ Thingibox] || ES || [http://store.thingibox.com/en/powertransmission/8-pulleys.html GT2 Pulley] || Aluminium || 4-6 mm || 5.00 mm || 16 || double || Length: 7mm; Worldwide shipping<br />
|-<br />
| [http://www.TriDPrinting.com/ TriDPrinting.com] || US || [http://www.TriDPrinting.com/Mechanical-Parts/ GT2 Pulley] || Aluminium || 6 mm || 5.00 mm || 16, 20 || double || Worldwide Delivery<br />
|-<br />
| Ultibots || US || [http://www.ultibots.com/gt2-timing-pulley-20-tooth/ Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|-<br />
| UltiMachine || US || [https://ultimachine.com/content/timing-pulley-gt2-20-tooth Pulley] || Aluminium || 6 mm || 5.00 mm || 20 || double || &nbsp;<br />
|}<br />
<br />
=== RobotDigg ===<br />
China manufacturer of T2.5 pulley, MXL pulley, GT2 pulleys. T2.5 belt, MXL belt and GT2 belt in different width, open ended and endless or closed-loop timing belt provider.<br />
T2.5 pulley 16 tooth 5mm bore<br />
T5 pulley 12 tooth 8mm bore<br />
MXL pulley 18 teeth 5mm bore<br />
MXL pulley 20 teeth 6.35mm bore<br />
MXL pulley 36 teeth 5mm bore<br />
MXL pulley 36 teeth 8mm bore<br />
GT2 pulley 16 teeth 5mm bore<br />
GT2 pulley 18 tooth 6.35mm bore<br />
GT2 pulley 20 teeth 5mm, 6.35mm bore and 8mm bore<br />
GT2 pulley 32 tooth 10mm bore<br />
GT2 pulley 36 teeth 5mm bore and 8mm bore<br />
GT2 pulley 40 tooth 5mm, 6.35mm 8mm bore n 10mm bore<br />
* [http://www.robotdigg.com/product/25/T2.5-pulley,-16-teeth,-5mm-bore T2.5 pulley, 16 tooth, 5mm bore]<br />
* [http://www.robotdigg.com/product/26/MXL-pulley,-18-tooth,-5mm-bore MXL pulley 18 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/147/36-Tooth-MXL-Pulley-with-5mm-Bore MXL pulley 36 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/148/36-Tooth-MXL-Pulley-with-8mm-Bore MXL pulley 36 teeth, 8mm bore]<br />
* [http://www.robotdigg.com/product/59/Rostock-16-Teeth-5mm-Bore-GT2-Pulley 2GT pulley 16 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/9/GT2-Pulley-20-Teeth-5mm-Bore 2GT pulley 20 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/23/GT2-Pulley-20-Teeth-8mm-Bore 2GT pulley 20 teeth, 8mm bore]<br />
* [http://www.robotdigg.com/product/149/10mm-bore-32-teeth-gt2-pulley GT2 pulley 32 tooth 10mm bore]<br />
* [http://www.robotdigg.com/product/24/GT2-Pulley-36-Teeth-5mm-Bore 2GT pulley 36 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/66/2gt-pulley-36-teeth-8mm-bore 2GT pulley 36 teeth, 8mm bore]<br />
* [http://www.robotdigg.com/product/116/2gt-pulley-40-teeth-5mm-bore 2GT pulley 40 teeth, 5mm bore]<br />
* [http://www.robotdigg.com/product/66/2gt-pulley-36-teeth-8mm-bore 2GT pulley 40 teeth, 6.35mm bore]<br />
* [http://www.robotdigg.com/product/146/GT2-40-Tooth-8mm-Bore-Pulley 2GTpulley 40 teeth, 8mm bore]<br />
MOQ 50pcs for Custom Pulleys.<br />
<br />
== Cable ==<br />
*Synchromesh<br />
**https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=5503&GroupID=312<br />
**https://sdp-si.com/eStore/PartDetail.asp?Opener=Group&PartID=84751&GroupID=768</div>Merlucin