All public logs

Combined display of all available logs of RepRap. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).

Logs

All public logs Abuse filter log Block log Content model change log Deletion log Import log Merge log Move log Patrol log Protection log Tag log Tag management log Upload log User creation log User rights log Performer:  Target (title or User:username for user):   Search titles starting with this text

From year (and earlier): From month (and earlier): all January February March April May June July August September October November December

Tag filter: 

Hide tag log

(newest | oldest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)

• 01:51, 11 April 2010 MattMoses (talk | contribs) uploaded File:Waxuum10.jpg (Wax master, silicone mold, polyurethane part.)
• 01:50, 11 April 2010 MattMoses (talk | contribs) uploaded File:Waxuum13.jpg (The finished wax master. The part is just a little do-nothing brick - it is not really a functional item.)
• 01:49, 11 April 2010 MattMoses (talk | contribs) uploaded File:Waxuum12.jpg (Later in the machining process. Note more wax has been collected.)
• 01:49, 11 April 2010 MattMoses (talk | contribs) uploaded File:Waxuum11.jpg (Closeup of case at beginning of test. The wax inside is molten so the interior is visible. Near the top of the case interior, note the slanted cut in the drain tube, where the thinner vent tube passes out and outside. Molten wax exits from the slanted )
• 01:47, 11 April 2010 MattMoses (talk | contribs) uploaded File:Waxuum8.jpg (A view of the test setup. Of course, this tool is meant to be installed on an automatic XYZ table (like RepRap or MakerBot) but for a quick test it was installed on the little manual Sherline. The waxuum was simply clamped to the vertical stage of the m)
• 01:46, 11 April 2010 MattMoses (talk | contribs) uploaded File:Waxuum9.jpg (Closeup view of nested drain and vent tubes at the cutting tip.)
• 01:45, 11 April 2010 MattMoses (talk | contribs) uploaded File:Waxuum5.jpg (Push-to-connect fitting visible on back.)
• 01:43, 11 April 2010 MattMoses (talk | contribs) uploaded File:Waxuum6.jpg (Third attempt. This one worked well enough to test. Solidified wax forms a film on the inside of the case. This design uses a nested drain and vent. The cutting tip exits to the left in the picture. The vent exits to the right. An eight-ohm heater i)
• 01:42, 11 April 2010 MattMoses (talk | contribs) uploaded File:Waxuum3.jpg (Second attempt. Vent and drain tubes run in parallel, with a sort of notch at the tip to allow molten wax to be replaced with air from the vent, then moved up the drain tube into the case. Push-to-connect fitting (visible behind case) is used to connect)
• 01:40, 11 April 2010 MattMoses (talk | contribs) uploaded File:Waxuum1.jpg (First attempt. This is just a single-tube needle with a heater and thermistor. The air tube is stuck in place with caulk. The lid, heater, ports, etc are held in place with JB-weld. This design did not work at all because there was not sufficient heat)
• 16:54, 10 April 2010 MattMoses (talk | contribs) uploaded File:Waxuum case parts.zip (waxuum case parts)
• 16:53, 10 April 2010 MattMoses (talk | contribs) uploaded File:WaxVacuum3.jpg (wax vacuum image)
• 21:40, 2 April 2010 User account MattMoses (talk | contribs) was created

(newest | oldest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)