Search results
Create the page "%s" on this wiki! See also the search results found.
File:Schematic power supply.pdf Power Supply shematic of how the different PCB,s connect(274 KB) - 09:50, 2 June 2014File:Rampage gear.png Direct Drive Gear for Stoutwind's Rampage Universal Single Extruder(481 × 415 (249 KB)) - 15:54, 24 November 2014File:Y-axis carriage 13a.jpg Only 3mm left for this rod. M-u-s-t--t-a-p--m-o-r-e...(1,280 × 962 (457 KB)) - 14:19, 11 December 2014File:Josef-Prusa-Vanilla-X-motor-end-1a.png Josef Prusa's original Prusa i3 vanilla X motor end.(725 × 690 (11 KB)) - 15:04, 17 December 2014File:Misan-X-motor-end.png Misan's improved Prusa i3 X motor end.(651 × 690 (10 KB)) - 15:14, 17 December 2014File:Misan-Improved-X-motor-end.png Misan's version of the X motor end with a few added cutouts.(651 × 690 (10 KB)) - 15:42, 17 December 2014File:Mecan0-X-motor-end-1a.png Mecan0's version of the Prusa i3 X motor end.(742 × 717 (13 KB)) - 15:55, 17 December 2014File:BQ-X-motor-end-1a.png This is bq's version of the Prusa i3 X motor end for their Prusa i3 Hephestos.(733 × 717 (8 KB)) - 16:48, 17 December 2014File:ATX cable extension 24 fem to male 2a.jpg ...emale connector of our 24-pin ATX extension cable plugged into the ATX PSU's male connector, after I yanked out all the lines that are not going to be u(1,280 × 1,581 (752 KB)) - 07:49, 26 December 2014File:Molestock S-3D printer.jpg Molestock 3D delta printer (Molestock S, ver. 2)(1,200 × 1,701 (157 KB)) - 17:00, 24 July 2015File:V3D Powerful Extruder MK1.jpeg Eftimie's Powerful Extruder experiment. First try.(2,448 × 1,748 (1.32 MB)) - 10:28, 8 February 2015File:GregsWadeV2 1a.jpg Greg's Wade's Accessible Extruder, version 2.(729 × 654 (80 KB)) - 18:59, 7 March 2015File:Screenshot from 2015-03-06 21-11-09.jpg Greg's Wade's reloaded, extruder body and guidler.(719 × 640 (85 KB)) - 16:42, 6 March 2015File:Fishbone gears 1a.jpg Greg's Wade's reloaded fishbone gears.(712 × 641 (122 KB)) - 00:49, 7 March 2015File:GearsGregs 1b.jpg Greg's gears for his Accessible Extruder. Gear ratio is 10:43.(729 × 653 (115 KB)) - 19:35, 7 March 2015File:Gregs V1 1b.jpg Greg's accessible extruder, Version 1.(734 × 649 (73 KB)) - 20:12, 7 March 2015File:Gregs hinged 1b.jpg Greg's Hinged Accessible Extruder, body and idler.(693 × 563 (79 KB)) - 20:27, 7 March 2015File:GregsGuidler 1b.jpg Wade's Greg's Geared Extruder with a Guidler. And what is a guidler, you may ask?(618 × 549 (90 KB)) - 22:26, 7 March 2015File:Misan bobsyouruncle 1b.jpg Misan's version of Greg's Wade's Geared Extruder.(750 × 684 (103 KB)) - 23:10, 7 March 2015File:I3 rework 1a.jpg i3 Rework extruder derived from ch1t0's design, STLs imported in OpenSCAD.(600 × 537 (109 KB)) - 04:33, 18 August 2015