Search results

Jump to: navigation, search

Create the page "%s" on this wiki! See also the search results found.

  • CartesianBOM
    = Bill of Materials (BOM) for Darwin's Cartesian Robot = * Darwin's design houses both metric and imperial equivalents:
    3 KB (518 words) - 06:23, 27 November 2011
  • DC Motor Driver 1 0
    | GND || It's recommended to connect this to the ground on your Arduino to share a common | PWM_A || This pin controls the speed of your motor's rotation. You need to supply it a PWM signal, which determines the speed.
    16 KB (2,496 words) - 10:31, 8 June 2013
  • DC Motor Driver 1 1
    | GND || It's recommended to connect this to the ground on your Arduino to share a common | PWM_A || This pin controls the speed of your motor's rotation. You need to supply it a PWM signal, which determines the speed.
    17 KB (2,658 words) - 13:05, 24 June 2014
  • Darlington power transistor
    This little guy is great for powering devices with an IC. it's basically two transistors in the same package; one connects to the low-powe
    484 bytes (72 words) - 09:46, 30 December 2014
  • DarwinConceptImprovements
    | eD/Vik || Bolts || Replace M3's with standard M5's? | Vik || Opto bracket || A bit more of a gap for the opto's legs wouldn't hurt
    2 KB (374 words) - 09:37, 26 November 2011
  • DarwinDesignFaults
    Hi, if there's any design faults you've discovered on the way to building your Darwin, ple
    1 KB (203 words) - 09:37, 26 November 2011
  • DarwinExtruderBOM
    The AoI files for all the extruder's rapid prototyped parts can be found in the [http://reprap.svn.sourceforge.n
    2 KB (272 words) - 00:18, 12 September 2013
  • DarwinExtruderController
    ...rkspace</tt> directory is the one created by Eclipse) to set the capacitor's value in the line By Ohm's law, V=IR or equivalently R=V/I. So R = 12V / 2A = 6&Omega; (ohms). So th
    12 KB (1,936 words) - 00:20, 12 September 2013
  • Extruder Controller Board v1.2
    ...ey happen to be listed pretty much in order of height above board, so that's not a bad order to install them in. ...rom the <tt>File</tt> menu. Select the extruder tab and set the capacitor's value:
    14 KB (2,352 words) - 17:21, 29 October 2015
  • Opto Endstop v1.0
    ...sition. This page tells you how to wire one up to a bracket used in Darwin's design (below). ...les from Sourceforge]. This zip file contains the Kicad source files, PDF's, as well as the GERBER files you can use to [[MakePCBInstructions|build it
    7 KB (1,036 words) - 15:24, 23 July 2015
  • DarwinPartDevelopment
    ...terim page is designed to host the developments required to achieve Darwin's replication. Darwin was originally designed with a support material write h
    6 KB (577 words) - 09:39, 26 November 2011
  • DarwinPowerAndCommunicationsCard
    ...p (G) and its associated capacitors. The data from (G) to and from RepRap's communications ring is sent and received by the connectors at (E). (F) is ..."none". If in doubt for the other settings, use the following (though it's not too important at this stage): 19200 baud, 8 bits, no parity, one stop
    16 KB (2,457 words) - 09:39, 26 November 2011
  • DarwinPowerAndCommunicationsCardTest
    ...p (G) and its associated capacitors. The data from (G) to and from RepRap's communications ring is sent and received by the connectors at (E). (F) is ..."none". If in doubt for the other settings, use the following (though it's not too important at this stage): 19200 baud, 8 bits, no parity, one stop
    13 KB (2,131 words) - 09:40, 26 November 2011
  • Power Distribution and Communications Board v1.2
    ...p (G) and its associated capacitors. The data from (G) to and from RepRap's communications ring is sent and received by the connectors at (E). (F) is This was our first experience with ordering bulk PCB's. There were a couple mistakes. We've very sorry. None are a big deal, mo
    15 KB (2,450 words) - 04:46, 25 July 2015
  • DarwinStepperController
    ...each one, then to write X, Y, or Z on that when it's dry. (Mystery: there's hardly a typewriter left on the planet; so how is it that everywhere still
    3 KB (430 words) - 20:08, 26 November 2011
  • Stepper Motor Controller Card v1.2
    ...each one, then to write X, Y, or Z on that when it's dry. (Mystery: there's hardly a typewriter left on the planet; so how is it that everywhere still
    6 KB (890 words) - 04:51, 25 July 2015
  • DarwinZD1901Opto
    That's it. Mount it as per the standard [[Opto Endstop v1.0|endstop]] assembly ins
    2 KB (334 words) - 09:47, 14 December 2014
  • DarwinZStageConstruction
    ...ns of 4x440mm M8 screw threads placed vertically along the edges of Darwin's cubic framework.
    1 KB (223 words) - 09:41, 26 November 2011
  • Darwin's Successful Elements, Worldwide
    available worldwide. Elements of Darwin's design which achieved this are listed below: * The caged PTFE section in Ian's extruder
    754 bytes (106 words) - 05:37, 18 July 2015
  • Design
    ==Adrian Bowyer's Concise Hardware Guide: == ...so broadly a principle high on the list trumps one below. But remember it's a ''guide'' not a moral absolute...
    1 KB (185 words) - 15:42, 4 January 2015

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)

Retrieved from "https://reprap.org/wiki/Special:Search"