Search results

Create the page "Useful Software Package" on this wiki! See also the search results found.

• Gen L Electronics
  ...lectronics is an in-development electronics package optimized for cost and software hackability == Software ==
  3 KB (490 words) - 12:39, 14 December 2014
• User:Bsutton
  I have one of these fitted to my printer (the first useful thing that I printed and I love it). Getting the bed height just right and This also looks useful
  24 KB (4,225 words) - 02:08, 1 November 2011
• Ppa install
  Here is Jonathan Marsden's personal package archive with the RepRap Debian/Ubuntu packages: To get the software for loading firmware into the Sanguino chip, issue the following commands (
  1 KB (143 words) - 17:17, 24 November 2011
• Debian package
  These are my notes on getting a debian package operational for reprap. I'm starting of using the debian package in the reprap hosts project.
  651 bytes (94 words) - 18:52, 26 March 2014
• RUG/Pennsylvania/State College/RepRap Media Timeline
  Summary: A 3D printing enthusiast set out to prove that useful items can be created by RepRaps by designing and printing all necessary par ...ty of Nevada, Reno has added two 3D printers, a 3D scanner, and supporting software available for general use to the school community. Thanks to professor Tod
  152 KB (22,645 words) - 01:20, 30 August 2019
• LongboatPrusa
  * A Dremel is useful for trimming the M8 mudguard washers ...tensioned so that there is little or no slack. (a second pair of hands is useful for this)
  49 KB (8,221 words) - 09:42, 26 March 2014
• User talk:Traumflug
  ...people who are not developers, the electronics is much more difficult than software. But I agree with you -- firmware and slicer are the most complex parts of ...eprap projects, to add information about Smoothie where it is relevant and useful to wiki users. I am perfectly ok with discussing those edits with somebody
  28 KB (4,490 words) - 23:13, 5 February 2015
• PrusaBuildNotesBraino
  I'm not do good with electronics (I'm more of a software guy), and saved my self at least a couple weeks with the solidoodle part. == Software ==
  59 KB (9,978 words) - 17:05, 12 April 2015
• LulzBot/AssembledPrusaMendel/gettingstarted
  ...setting up your printer make sure all of the items on the list are in your package. =Getting software=
  14 KB (2,517 words) - 12:37, 14 March 2012
• Stepper motor driver
  ! Package ...s 1/16 microstepping, and some people prefer this TSSOP package over a QFN package.
  23 KB (3,496 words) - 07:24, 1 May 2018
• USBasp
  ...ore'' the 10pin header, made sure there were no solder-bridges and ran the software.<br> =Software=
  4 KB (664 words) - 01:01, 23 August 2015
• FilamentEsunplaReviews
  From the time I sent the money via paypal, it took 13 days to receive the package in Pennsylvania, USA. ...ite a bit when idle in the extruder. After that, and adjusting my extruder/software for the 1.7mm filament, I started Printing.
  5 KB (883 words) - 11:51, 19 March 2014
• Printrboard
  ==Software== ...ac/Linux: packaged with [http://www.atmel.com/tools/FLIP.aspx Atmel's FLIP software].
  23 KB (3,566 words) - 13:32, 11 March 2020
• Gen7 Board 1.4.1
  * Download and unpack or install the [http://arduino.cc/en/Main/Software Arduino IDE]. You need v1.0.3 or later. If you insist on v0023 or earlier f ...bootloader. Bootloader binaries come with the [[Gen7 Arduino IDE Support]] package, so upload instructions can also be found [[Gen7 Arduino IDE Support#Bootlo
  52 KB (8,394 words) - 15:13, 14 November 2015
• Talk:Comparison of Electronics
  ...at look at this as a complete newcomer. And while the spreadsheet has some useful information (and a LOT of question marks), I can see how this table will st 1) Total cost of electronics package, including a minimum of 4 stepper drivers, 2 temperature, and two heater po
  13 KB (2,117 words) - 08:29, 6 March 2016
• Azteeg X1
  ...t 12v power supply of yours). You need to use a higher rated TVS diode(SMB package) if using a higher voltage power supply.}} === Software ===
  13 KB (2,228 words) - 18:42, 18 November 2014
• XtruBot
  ...xpress/ PTC Creo Elements/Direct Modeling Express 4.0] as the CAD software package to develop custom 3D RepRap parts and assemblies for XtruBot<br> * Conducted a cursory review of available G-Code software and tentatively selected [http://replicat.org/ ReplicatorG] for use with Xt
  7 KB (1,109 words) - 15:08, 22 March 2012
• Gen7 Board 1.4.1/fr
  * Téléchargez, décompressez et installez [http://arduino.cc/en/Main/Software|Arduino IDE].Vous devez utiliser la version 2.0 ou celle suivante. Si vous ...%20Arduino%20IDE%20Support%202.0.zip?raw=true Gen7 Arduino IDE Support 2.0 package].
  72 KB (11,247 words) - 21:00, 31 January 2013
• WPI Rostock Distro
  ...WPI [[Rostock]] distribution is a complete software and hardware sourcing package. In order ease the construction and support of the Rostock at WPI.
  537 bytes (71 words) - 09:01, 23 January 2016
• User:Kpb5069
  ...er nerds. We have people who develop firewall programs and other security software which try to prevent these viruses from entering your computer itself. I t ...rspace of this nature would definitely be utilized by students and be very useful for academic advancement as well as personal growth.
  41 KB (7,008 words) - 01:10, 13 December 2012

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)