ToyREP Buyers Guide
From RepRap
Revision as of 18:29, 5 August 2015 by
Thorgal
(
talk
|
contribs
)
(Created page with "{| class="wikitable sortable" border="1" ! scope="col" class="unsortable" | Picture ! scope="col" | Quantity ! scope="col" | Description ! scope="col" class="unsortable" | Com...")
(diff) ← Older revision |
Latest revision
(
diff
) |
Newer revision →
(
diff
)
Jump to:
navigation
,
search
Picture
Quantity
Description
Comments
1
PSU Cover
Chose PSU1.stl (111x78x36mm big PSU) or PSU2.stl (129x99x38mm big PSU)
1
1.8m Power Supply cable with plug
cca 1.5-2mm long PC cable would be just fine - cut of the computer Euro connector, keep power socket plug.
1
200mm Dual Line cable
Should be able to withstand at least 12V 4A, Insulation with two colours to distinguish +12V and -12V
1
Power supply switch (250V, 1A)
Installation into panel with mounting hole 13x19mm
4
Ø6mmx25 Heat Shrink
1
3X13 Round-pan Wood Screw
1
Cable Tie
1
PCB Mount
Chose PCB1-1.stl for PSU1 or PCB2-1.stl PSU2.stl for PSU2
1
PCB Mount
Chose PCB1-2.stl for PSU1 or PCB2-2.stl PSU2.stl for PSU2
2
M8x255mm Threaded Rod
Alternatively 265mm long for PSU2 and/or 125x125mm print area or 240mm for printer with 100x100mm print area and without PSU.
1
M8x245mm Threaded Rod
Alternatively 265mm long for PSU2 and/or 125x125mm print area or 230mm for printer with 100x100mm print area and without PSU.
6
M8 Hex Nut
6
M8 Washer
3
M3X10 Countersunk Screw
1
Left Z Motor Mount
1
Right Z Motor Mount
2
28BYJ-48 Stepper Motor
Length of wire c. 120mm and 180mm
2
Ø8x295mm Smooth Rod
1
M8x245mm Threaded Rod
Alternatively 265mm long for PSU2 and/or 125x125mm print area or 230mm for printer with 100x100mm print area and without PSU.
8
M8 Hex Nut
38
M8 Washer
Additional washer are used to set correct distance between plastic parts. The amount can vary.
1
M3x90mm Threaded Rod
4
M3 Hex Nut
1
M3 Washer
4
3X13 Round-pan Wood Screw
1
Rear Y Axis Bearing Mount
2
Y Frame Corner Leg
1
624ZZ Ball Bearing
2
M8x170mm Threaded Rod
Alternatively 180mm long for PSU2 and/or 125x125mm print area or 155mm for printer with 100x100mm print area and without PSU.
12
M8 Hex Nut
12
M8 Washer
1
M4x20mm Round-pan Screw
1
M4 Hex Nut
3
M4 Washers
1
M6 Mudgard Washer
1
Front Y Axis Motor Mount
2
Y Frame Corner Leg
1
T2.5 Timing Belt Pulley
1
28BYJ-48 Stepper Motor
Length of wire c. 250mm
1
Micro Switch
Mounting holes Ø2.5mm 11mm apart, length of wire c. 300mm
2
M8x170mm Threaded Rod
Alternatively 180mm long for PSU2 and/or 125x125mm print area or 155mm for printer with 100x100mm print area and without PSU.
12
M8 Hex Nut
12
M8 Washer
2
3X13 Round-pan Wood Screw
2
2.5X10 Round-pan Wood Screw
8
M8 Hex Nut
8
M8 Washer
1
Frog base
2
Frog extenders. Use Frog_100 for 100x100mm print area or Frog_125 for 125x125mm print area
4
LM8UU Bearing
4
M4 Hex Nut
4
M4x50 Countersunk Screws
4
M3 Nylock Nut
8
Cable Tie
2
Ø8x225mm Smooth Rod
Alternatively 245mm long for PSU2 and/or 125x125mm print area or 220mm for printer with 100x100mm print area and without PSU.
1
T2.5x500mm Timing belt
Alternatively 520mm long for PSU2 and/or 125x125mm print area or 470mm for printer with 100x100mm print area and without PSU.
1
Frog base
1
Left X Axis
1
Right X Axis
2
Z Axis Top Bracing
2
Z Axis Motor Joint
1
T2.5 Timing Belt Pulley
1
28BYJ-48 Stepper Motor
Length of wire c. 500mm
2
Micro Switch
Mounting holes Ø2.5mm 11mm apart, length of wire c. 850mm
7
LM8UU Bearing
1
624ZZ Ball Bearing
2
Ø8x245mm Smooth Rod
Alternatively 255mm long for PSU2 and/or 125x125mm print area or 230mm for printer with 100x100mm print area and without PSU.
1
M8x255mm Threaded Rod
Alternatively 265mm long for PSU2 and/or 125x125mm print area or 240mm for printer with 100x100mm print area and without PSU.
2
M5x250mm Threaded Rod
1
T2.5x480mm Timing belt
Alternatively 500mm long for PSU2 and/or 125x125mm print area or 450mm for printer with 100x100mm print area and without PSU.
2
Ø8/5x20mm PVC Tube
4
M8 Hex Nut
4
M8 Washer
2
M5 Hex Nut
1
M4x20mm Round-pan Screw
1
M4 Hex Nut
3
M4 Washers
1
M6 Mudgard Washer
4
M3x20mm Countersunk Screw
4
M3 Hex Nut
2
3X13 Round-pan Wood Screw
4
2.5X10 Round-pan Wood Screw
14
Cable Tie
1
Extruder body
1
Extruder Idler
1
Big Gear With 36 Teeth
1
Small Gear With 9 Teeth
1
Fan And Hotend Mount
1
28BYJ-48 Stepper Motor
Length of wire c. 850mm
1
E3D Clone
With 12V 40W ceramic heat cartridge and 100k Ohm thermistor, length of wire c. 950mm
1
40x40x10mm Fan
Small 12V fan, length of wire c. 950mm
3
608ZZ Bearing
1
M8 Hobbed bolt
for eg. Hyena hobbed bolt.
1
Ø8x15mm Smooth Rod
1
M8 Nylock Nut
4
M8 Washer
2
M4x50mm Round-pan Screw
2
M4 Hex Nut
4
M4 Washers
2
Ø7/5x15mm Spring
4
M3x35mm Round-pan Screw
2
M3x30mm Countersunk Screw
2
M3x25mm Countersunk Screw
4
M3x16mm Round-pan Screw
2
M3 Nylock Nut
1
M3 Hex Nut
4
M3x12 Hex Nut
If long hex nut not available glue into each hole of fan mount two M3 nuts. Keep them apart.
7
M3 washer
2
3X13 Round-pan Wood Screw
10
Cable Tie
1
120x120x3mm Polycarbonate Plate
Mounting holes in corners 105x105mm apart. Bigger bed is 145x145x3mm with mounting holes 130x130mm apart.
4
Ø7/5x15mm Spring
4
M3x25mm Countersunk Screw
8
M3 washer
Eventually M4 Washers
Navigation menu
Personal tools
Create account
Log in
Namespaces
Page
Discussion
Variants
Views
Read
View source
View history
More
Search
Navigation
Main Page
Build a RepRap
Glossary
Reference
Participation
Recent Changes
Get a Wiki account
Create a new page
Policy
Community
RepRap Forum
RepRap IRC
Development Index
RepRap User Groups
Community Portal
Licence
Tools
What links here
Related changes
Special pages
Printable version
Permanent link
Page information
Cite this page