User contributions
(newest | oldest) View (newer 20 | older 20) (20 | 50 | 100 | 250 | 500)
- 19:30, 29 September 2015 (diff | hist) . . (+15) . . List of electronics (→Duet)
- 19:27, 29 September 2015 (diff | hist) . . (+137) . . List of electronics (→Duet)
- 19:21, 29 September 2015 (diff | hist) . . (+47) . . List of electronics (→Duet: - add new board 5 axis)
- 08:40, 26 September 2015 (diff | hist) . . (0) . . m Linear bearing (→Name) (current)
- 07:48, 26 September 2015 (diff | hist) . . (+116) . . Linear bearing (→Common Linear Bearing Dimensions: separate table for bearings and pillow blocks)
- 07:45, 26 September 2015 (diff | hist) . . (+244) . . Linear bearing (→Common Linear Bearing Dimensions: Add long bearings and 12 & 16 mm bearings)
- 07:38, 26 September 2015 (diff | hist) . . (+206) . . Linear bearing (→Name: add short and long denomination)
- 13:57, 22 September 2015 (diff | hist) . . (+49) . . Joints for Delta Printer (→DIY / RepRap Cardan Joint: add rotational stiffness in advantages)
- 16:53, 4 September 2015 (diff | hist) . . (+34) . . G-code (→M122: Diagnose: RRF yes on DC42 branch - may work on main branch)
- 16:47, 4 September 2015 (diff | hist) . . (+24) . . G-code (→M405: Filament Sensor on: RRF no test on DC42 branch)
- 16:44, 4 September 2015 (diff | hist) . . (+22) . . G-code (→G: List all G-codes)
- 16:41, 4 September 2015 (diff | hist) . . (+25) . . G-code (→M600: Filament change pause: RRF no test on DC42 branch)
- 16:38, 4 September 2015 (diff | hist) . . (+39) . . G-code (→M503: Print settings: yes - tested on DC42 branch - may work on main branch)
- 16:31, 4 September 2015 (diff | hist) . . (+25) . . G-code (→M360: Report firmware configuration: RRF no test on DC42 branch)
- 16:28, 4 September 2015 (diff | hist) . . (+24) . . G-code (→M230: Disable / Enable Wait for Temperature Change: RRF no test on DC42 branch)
- 16:20, 4 September 2015 (diff | hist) . . (+24) . . G-code (→M218: Set Hotend Offset: RRF no test on DC42 branch)
- 16:18, 4 September 2015 (diff | hist) . . (+24) . . G-code (→M209: Enable automatic retract: RRF no test on DC42 branch)
- 16:17, 4 September 2015 (diff | hist) . . (+24) . . G-code (→M207: Set retract length: RRF no test on DC42 branch)
- 16:15, 4 September 2015 (diff | hist) . . (+24) . . G-code (→M113: Set Extruder PWM: RRF no test on DC42 branch)
- 16:13, 4 September 2015 (diff | hist) . . (+24) . . G-code (→M108: Set Extruder Speed: no - test on DC42 branch)
(newest | oldest) View (newer 20 | older 20) (20 | 50 | 100 | 250 | 500)