User contributions
(newest | oldest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)
- 16:15, 21 October 2019 (diff | hist) . . (+34) . . G-code (→M133: Set PID I limit value)
- 16:14, 21 October 2019 (diff | hist) . . (+34) . . G-code (→M132: Set PID D value)
- 16:13, 21 October 2019 (diff | hist) . . (+52) . . G-code (→M131: Set PID I value)
- 16:13, 21 October 2019 (diff | hist) . . (+52) . . G-code (→M130: Set PID P value)
- 16:11, 21 October 2019 (diff | hist) . . (-232) . . G-code (M710 is defunct unless others implement it)
- 16:01, 21 October 2019 (diff | hist) . . (-92) . . G-code (→M703: Get Board Type / Configure Filament: bq is non-standard)
- 15:58, 21 October 2019 (diff | hist) . . (+339) . . G-code (→M702: Unload filament: Add Marlin M702 parameters)
- 15:52, 21 October 2019 (diff | hist) . . (+137) . . G-code (→M701: Load filament: Add Marlin parameters)
- 15:31, 21 October 2019 (diff | hist) . . (-9) . . G-code (→M700: Level plate: Strictly, no)
- 15:29, 21 October 2019 (diff | hist) . . (+48) . . G-code (→M675: Find center of cavity)
- 15:29, 21 October 2019 (diff | hist) . . (+48) . . G-code (→M674: Set Z to center point)
- 15:28, 21 October 2019 (diff | hist) . . (+48) . . G-code (→M673: Align plane on rotary axis)
- 15:28, 21 October 2019 (diff | hist) . . (+48) . . G-code (→M672: Program Z probe)
- 15:27, 21 October 2019 (diff | hist) . . (+53) . . G-code (→M671: Define positions of Z leadscrews or bed leveling screws)
- 15:26, 21 October 2019 (diff | hist) . . (+48) . . G-code (→M670: Set IO port bit mapping)
- 15:25, 21 October 2019 (diff | hist) . . (+48) . . G-code (→M669: Set kinematics type and kinematics parameters)
- 15:24, 21 October 2019 (diff | hist) . . (+48) . . G-code (→M668: Set Z-offset compensations polynomial)
- 15:23, 21 October 2019 (diff | hist) . . (+18) . . G-code (→M665: Set delta configuration)
- 15:23, 21 October 2019 (diff | hist) . . (+48) . . G-code (→M666: Set delta endstop adjustment)
- 15:22, 21 October 2019 (diff | hist) . . (+45) . . G-code (→M665: Set delta configuration)
- 15:21, 21 October 2019 (diff | hist) . . (+47) . . G-code (→M651: execute peel move)
- 15:21, 21 October 2019 (diff | hist) . . (+47) . . G-code (→M650: Set peel move parameters)
- 15:19, 21 October 2019 (diff | hist) . . (+15) . . G-code (→M605: Set dual x-carriage movement mode)
- 15:19, 21 October 2019 (diff | hist) . . (+1) . . G-code (→M600: Filament change pause)
- 15:17, 21 October 2019 (diff | hist) . . (+16) . . G-code (→M600: Filament change pause)
- 16:12, 19 October 2019 (diff | hist) . . (+15) . . G-code (→M600: Set line cross section)
- 16:11, 19 October 2019 (diff | hist) . . (+63) . . G-code (→M575: Set serial comms parameters)
- 16:10, 19 October 2019 (diff | hist) . . (-2,076) . . G-code (Oops.Try that again.)
- 16:06, 19 October 2019 (diff | hist) . . (+2,664) . . G-code (Update some RepRapFirmware codes)
- 16:04, 19 October 2019 (diff | hist) . . (+49) . . G-code (→M559: Upload configuration file)
- 16:04, 19 October 2019 (diff | hist) . . (+50) . . G-code (→M558: Set Z probe type)
- 16:04, 19 October 2019 (diff | hist) . . (+49) . . G-code (→M557: Set Z probe point or define probing grid)
- 16:03, 19 October 2019 (diff | hist) . . (+49) . . G-code (→M556: Axis compensation)
- 16:03, 19 October 2019 (diff | hist) . . (+49) . . G-code (→M555: Set compatibility)
- 16:02, 19 October 2019 (diff | hist) . . (+49) . . G-code (→M554: Set Gateway)
- 16:02, 19 October 2019 (diff | hist) . . (+49) . . G-code (→M553: Set Netmask)
- 16:02, 19 October 2019 (diff | hist) . . (+49) . . G-code (→M552: Set IP address, enable/disable network interface)
- 16:01, 19 October 2019 (diff | hist) . . (+49) . . G-code (→M551: Set Password)
- 16:01, 19 October 2019 (diff | hist) . . (+49) . . G-code (→M550: Set Name)
- 16:01, 19 October 2019 (diff | hist) . . (+63) . . G-code (→M540 in Marlin: Enable/Disable "Stop SD Print on Endstop Hit")
- 16:00, 19 October 2019 (diff | hist) . . (+32) . . G-code (→M540: Set MAC address)
- 15:59, 19 October 2019 (diff | hist) . . (+51) . . G-code (→M532: Set print progress)
- 15:56, 19 October 2019 (diff | hist) . . (+15) . . G-code (→M531: Set print name)
- 15:55, 19 October 2019 (diff | hist) . . (+32) . . G-code (→M530: Enable printing mode)
- 15:54, 19 October 2019 (diff | hist) . . (+15) . . G-code (→M530: Enable printing mode)
- 15:54, 19 October 2019 (diff | hist) . . (+47) . . G-code (→M524: Abort SD Printing)
- 15:53, 19 October 2019 (diff | hist) . . (+16) . . G-code (→M524: Abort SD Printing)
- 15:52, 19 October 2019 (diff | hist) . . (+48) . . G-code (→M504: Validate EEPROM)
- 15:52, 19 October 2019 (diff | hist) . . (+39) . . G-code (→M503: Print settings)
- 15:51, 19 October 2019 (diff | hist) . . (+17) . . G-code (→M502: Read parameters from "configuration.h")
(newest | oldest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)