File list
This special page shows all uploaded files.
| Date | Name | Thumbnail | Size | Description | Versions |
|---|---|---|---|---|---|
| 12:53, 8 June 2006 | RPOrders-railed poly-holder.stl (file) |  |
126 KB | Poly holder with a couple of 0.6mm barriers on it. | 1 |
| 06:16, 4 June 2006 | BlogPhotosFromVik-polymorph feedstock jam sml.jpg (file) |  |
33 KB | Polymorph feedstock jamming up and wrapping around the threaded rod. | 1 |
| 12:16, 23 May 2006 | Screw-drivenLinearStage-stage linkage 1 of.stl (file) | |
40 KB | STL file for Stage/table linkage. Make 1. (Same model as linear axis) | 1 |
| 04:15, 23 May 2006 | VikOlliver-electric screwdriver extruder.jpg (file) |  |
69 KB | Electric screwdriver used to drive extruder, held with Polymorph | 1 |
| 14:03, 14 May 2006 | VikOlliver-first extruded recognisablesquare and hexagon sml.jpg (file) |  |
40 KB | This is the first recognisable extrusion by the RepRap. A square and hexagon. | 1 |
| 11:34, 14 May 2006 | VikOlliver-repraptwo.png (file) |  |
215 KB | Plot of single Produce layer using a pen instead of extruder. | 1 |
| 14:47, 13 May 2006 | VikOlliver-first attempt at produce sml.jpg (file) |  |
60 KB | First crack at Produce test. Hexagon on left, square on right. Y axis underscaled. | 1 |
| 14:08, 11 May 2006 | VikOlliver-first run of x and y deposition sml.jpg (file) |  |
32 KB | The first run of the X-Y axes with extrusion and java-levelled Z axis. | 1 |
| 02:07, 8 May 2006 | BuildingAStripboardStepperController-StepperStripboardTop.png (file) |  |
158 KB | Component side of board | 1 |
| 01:56, 8 May 2006 | BuildingAStripboardStepperController-xaxis 2803.png (file) |  |
11 KB | Schematic for axis controller using ULN2803 octal driver | 1 |
| 03:55, 7 May 2006 | MeasuringThermistorBeta-ThermistorBeta.ods (file) | |
7 KB | OpenDocument Spreadsheet for calculating thermistor Beta and Rz | 1 |
| 01:31, 25 March 2006 | BuildingAStripboardExtruderController-ExtruderStripboardTop SN754410.svg (file) |  |
495 KB | Source for extruder stripboard layout | 1 |
| 01:27, 25 March 2006 | BuildingAStripboardExtruderController-ExtruderStripboardTop SN754410.png (file) |  |
313 KB | Extruder stripboard layout, component side. | 1 |
| 06:09, 13 March 2006 | StepperDriverWithUDN2559-2559 Stepper Stripboard top.png (file) |  |
153 KB | Top view of 2559 Stepper Motor on Stripboard | 1 |
| 06:05, 13 March 2006 | StepperDriverWithUDN2559-xaxis-2559.png (file) |  |
9 KB | Schematic of 2559-based stepper driver. | 1 |
| 13:51, 26 February 2006 | StepperDriverWithUDN2559-2559 Stepper board prototype.jpg (file) |  |
78 KB | First attempt at UDN2559 steppr driver. | 1 |
| 13:54, 24 February 2006 | Screw-drivenLinearStage-screw-driven stage4.aoi (file) | |
1.74 MB | Complete AoI files for the MK3 stage | 1 |
| 13:49, 24 February 2006 | Screw-drivenLinearStage-stage table 1 of.stl (file) | |
410 KB | STL File for stage table. Make 1. Large part (120x105mm approx) | 1 |
| 13:43, 24 February 2006 | Screw-drivenLinearStage-Stage base 1 of.stl (file) | |
438 KB | STL File for base of stage. Make 1. | 1 |
| 07:25, 18 February 2006 | VikOlliver-concrete extrusion body iunder test sml.jpg (file) |  |
79 KB | The concrete insulator fitted to an extruder under test @107C | 1 |
| 13:42, 10 February 2006 | HighTemperatureMaterials-first concrete insulator.jpg (file) |  |
43 KB | The first concrete insulator just out of its mould. | 1 |
| 04:45, 31 January 2006 | Screw-drivenLinearStage-screw-driven stage3.aoi (file) | |
1.47 MB | Old AoI File for the complete Mk2 stage | 1 |
| 04:39, 31 January 2006 | Screw-drivenLinearStage-spreader 2 of.stl (file) | |
663 KB | STL file for spreader to space rails on stage. Make 2. | 1 |
| 01:14, 30 January 2006 | VikOlliver-Mk1 Stage Assembled.jpg (file) |  |
97 KB | Mk 1 FDM !Stage assembled without limit switches | 1 |
| 01:14, 30 January 2006 | Screw-drivenLinearStage-Mk1 Stage Assembled.jpg (file) |  |
97 KB | Mk 1 FDM !Stage assembled without limit switches | 1 |
| 23:42, 29 January 2006 | AlreadyDoneList-reprap 2005.odp (file) | |
10.13 MB | Presentation on RepRap to !LinuxConf Australia 2006 by Vik Olliver | 1 |
| 05:18, 8 January 2006 | InterchangeableNozzleMk2-detatchable nozzle assy sml.jpg (file) |  |
22 KB | The detatchable nozzle concept. This one has been reduced in diameter with solder around a piece of nichrome wire, which is then removed to leave the vital hole. | 1 |
| 01:44, 5 January 2006 | Half-roundWasherBearing-half-washer bearings installed.jpg (file) |  |
28 KB | Half-washer bearings installed in the extruder. | 1 |
| 01:44, 5 January 2006 | Half-roundWasherBearing-stack of half-washers.jpg (file) |  |
24 KB | Completed stack of half-washers | 1 |
| 01:43, 5 January 2006 | Half-roundWasherBearing-stacking half-washers.jpg (file) |  |
28 KB | Stacking half-washers in the bearing well | 1 |
| 01:59, 3 January 2006 | Screw-drivenLinearStage-screw-driven stage2.aoi (file) | |
1.11 MB | DO NOT USE - AoI files for the complete Mk1 stage | 1 |
| 08:38, 28 December 2005 | VikOlliver-reprap first 3D cartesian sml.jpg (file) |  |
89 KB | First 3D Cartesian reprap axis | 1 |
| 08:36, 28 December 2005 | VikOlliver-reprap first 3D cartesian.jpg (file) |  |
1.25 MB | First 3D Cartesian reprap axis | 1 |
| 04:22, 18 December 2005 | VerticalPlatform-complete vertical axis gear end sml.jpg (file) |  |
38 KB | Vertical axis showing gear end | 1 |
| 04:21, 18 December 2005 | VerticalPlatform-complete vertical axis smg.jpg (file) |  |
52 KB | The vertical axis main component assembled. | 1 |
| 20:50, 16 December 2005 | Screw-drivenLinearAxis-linear axis with meccano carriage sml.jpg (file) |  |
28 KB | Assembled linear axis with Meccano carriage and spider for scale. | 1 |
| 20:34, 15 December 2005 | Screw-drivenLinearAxis-linear screw axis clamp collage.jpg (file) |  |
42 KB | Collage showing rail clamp, bearing and spider mechanism. | 1 |
| 09:46, 1 December 2005 | Screw-drivenLinearAxis-carriage2.aoi (file) | |
1.25 MB | Carriage ArtOfIllusion source file, complete with workings. | 1 |
| 09:39, 1 December 2005 | Screw-drivenLinearAxis-nut holder 3 of.stl (file) | |
155 KB | Nut holder. Attaches vertical axis. | 1 |
| 09:38, 1 December 2005 | Screw-drivenLinearAxis-linkage 2 of.stl (file) | |
76 KB | Linkage joining the carriage to the driving threaded rod. | 1 |
| 09:36, 1 December 2005 | Screw-drivenLinearAxis-Carriage 1 of.stl (file) | |
1.87 MB | Carriage model - probably best oriented the other way up. | 1 |
| 09:28, 1 December 2005 | Screw-drivenLinearAxis-Carriage parts.jpg (file) |  |
123 KB | How the parts of the carriage correspond to the spider (orange) | 1 |
| 11:04, 29 November 2005 | Screw-drivenLinearAxis-rail clamp.stl (file) | |
1.01 MB | 8mm Rail and bearing clamping block for screw-driven linear axis. | 1 |
| 11:02, 29 November 2005 | Screw-drivenLinearAxis-rail clamping block2.aoi (file) | |
683 KB | MkII Rail clamping block, designed for 8mm rails. | 1 |
| 00:32, 27 November 2005 | Screw-drivenLinearAxis-rail clamping block.aoi (file) | |
490 KB | DO NOT USE - Clamping block has wrong diameter clamps | 1 |
| 03:41, 26 November 2005 | VerticalPlatform-spider rendering.jpg (file) |  |
18 KB | AoI Rendering of the spider designed to hold the gears | 1 |
| 22:19, 25 November 2005 | VerticalPlatform-lower spider2.aoi (file) | |
499 KB | Second version of the spider used to hold the vertical axis gears | 1 |
| 06:29, 17 November 2005 | GearDesignInAoI-set cog smoothness.png (file) |  |
25 KB | Setting the smoothness of the cog teeth | 1 |
| 01:49, 17 November 2005 | GearDesignInAoI-aoi cog window.png (file) |  |
5 KB | The AoI Cog creation dialogue | 1 |
| 08:31, 5 November 2005 | PrototypePrinter-carriage w vert stepper.jpg (file) |  |
54 KB | Meccano carriage showing turntable and vertical stepper motor | 1 |
