File list
This special page shows all uploaded files.
| Date | Name | Thumbnail | Size | Description | Versions |
|---|---|---|---|---|---|
| 15:53, 11 December 2014 | Y-axis motor end 8a.JPG (file) |  |
374 KB | If you look carefully at where the arrow is pointing you can see the interference between the stepper and the nyloc nut, and where the stepper body has been filed away slightly. | 1 |
| 02:19, 11 December 2014 | Y-axis motor end 7a.JPG (file) |  |
458 KB | The Y-axis stepper and GT2 pulley installed. | 1 |
| 07:18, 22 November 2014 | Y-axis motor end 4a.JPG (file) |  |
462 KB | Use 2 x 8mm M3 screws to attach the stepper to the support part. Insert the pulley oriented as shown but do not screw it yet. | 1 |
| 06:56, 22 November 2014 | Y-axis motor end 3a.JPG (file) |  |
723 KB | The wrong way to do it (by trial and error, where each try means filing away some more of the stepper). | 1 |
| 18:48, 21 November 2014 | Y-axis motor end 2a.JPG (file) |  |
577 KB | This nut interferes with the stepper. | 1 |
| 18:37, 21 November 2014 | Y-axis motor end 1a.JPG (file) |  |
366 KB | The left Y motor end support installed. | 1 |
| 03:47, 8 December 2014 | Y-axis idler end 1a.JPG (file) |  |
582 KB | The P3Steel Y-axis idler assembly. | 1 |
| 17:20, 21 November 2014 | Y-axis done 1a.JPG (file) |  |
1,004 KB | Y-axis assembly minus the GT2 belt. | 1 |
| 08:19, 11 December 2014 | Y-axis carriage 9a.jpg (file) |  |
831 KB | Continuing with the tapping, the rods will progressively move into the frame. | 1 |
| 06:48, 11 December 2014 | Y-axis carriage 8a.jpg (file) |  |
827 KB | Tapping the rod ends gently with the hammer, push them through their supports on the P3Steel frame. We can slide out the Y-carriage now. | 1 |
| 05:04, 11 December 2014 | Y-axis carriage 4a.jpg (file) |  |
697 KB | While holding the Y carriage horizontal, manually engage the two smooth rods in the back supports. | 1 |
| 16:05, 11 December 2014 | Y-axis carriage 3a.jpg (file) |  |
581 KB | Y-axis carriage assembled, top view. | 1 |
| 03:09, 11 December 2014 | Y-axis carriage 1a.jpg (file) |  |
633 KB | The Y-carriage with the 8mm smooth rods and the GT2 belt holder installed. | 1 |
| 14:43, 11 December 2014 | Y-axis carriage 16a.jpg (file) |  |
398 KB | Done tapping here too (front right). | 1 |
| 14:33, 11 December 2014 | Y-axis carriage 15a.jpg (file) |  |
372 KB | Back left rod seems OK. We are definitely done tapping here! | 1 |
| 14:25, 11 December 2014 | Y-axis carriage 14a.jpg (file) |  |
424 KB | We are done here (front left)! | 1 |
| 14:52, 11 December 2014 | Y-axis carriage 13b.jpg (file) |  |
472 KB | Guiding the smooth rod into the frame support, detail. | 1 |
| 14:19, 11 December 2014 | Y-axis carriage 13a.jpg (file) |  |
457 KB | Only 3mm left for this rod. M-u-s-t--t-a-p--m-o-r-e... | 1 |
| 13:51, 11 December 2014 | Y-axis carriage 12a.jpg (file) |  |
541 KB | We must guide the smooth rods into their corresponding slots manually as we tap them in for the last few millimeters. | 1 |
| 08:34, 11 December 2014 | Y-axis carriage 11a.jpg (file) |  |
553 KB | We can slide the Y-carriage back in place once the smooth rods have been pushed in far enough. | 1 |
| 08:27, 11 December 2014 | Y-axis carriage 10a.jpg (file) |  |
689 KB | Patience! Go on tapping with the hammer... | 1 |
| 08:16, 13 December 2014 | Y-axis belt holder 5a.JPG (file) |  |
396 KB | The GT2 belt and holder properly installed under the heatbed and Y-carriage. | 1 |
| 12:51, 9 August 2015 | UGWG extruder Gears 1a.jpg (file) |  |
119 KB | Fishbone gears for the Ultimate Greg's Wade's Geared Extruder, August 2015. | 1 |
| 12:44, 9 August 2015 | UGWG extruder Body 1a.jpg (file) |  |
107 KB | Ultimate Greg's Wade's Geared Extruder, 30mm version, OpenSCAD render. | 1 |
| 17:18, 21 November 2014 | Tools 3a.JPG (file) |  |
459 KB | A small hammer. | 1 |
| 17:18, 21 November 2014 | Tools 2a.JPG (file) |  |
754 KB | M8 hex key and 14mm wrench. | 1 |
| 17:14, 21 November 2014 | Tools 1a.JPG (file) |  |
470 KB | A small metal file and M3 hex key. | 1 |
| 09:49, 6 August 2015 | Stoffel15 Wade Gears.jpg (file) |  |
118 KB | Herringbone aka fishbone gears for Wade's geared extruder by Stoffel15. | 1 |
| 09:40, 22 December 2014 | Stepper drivers mixed a4988 drv8825 RAMPS 1a.jpg (file) |  |
612 KB | Mixing A4988 and DRV8825 stepper drivers on the same RAMPS 1.4? Yes, you can! | 1 |
| 07:05, 21 December 2014 | Stepper drivers a4988 drv8825 4a.jpg (file) |  |
467 KB | A4988 and DRV8825 stepper driver boards, underside. | 1 |
| 21:41, 19 December 2014 | Stepper drivers a4988 drv8825 3a.jpg (file) |  |
413 KB | A4988 and DRV8825 stepper driver boards side by side. | 1 |
| 16:42, 6 March 2015 | Screenshot from 2015-03-06 21-11-09.jpg (file) |  |
85 KB | Cropped. | 2 |
| 15:26, 22 February 2015 | Screenshot OctoPrint.jpg (file) |  |
298 KB | A partial screenshot of OctoPrint running on an OctoGoatBox. | 1 |
| 04:28, 29 January 2015 | Rostock Delta Kinematics 3.pdf (file) |  |
3.19 MB | A simple, clear explanation of the forward and reverse kinematics for linear delta printers, by Steve Graves. | 1 |
| 13:15, 10 August 2015 | Reloaded Bowden 2a.jpg (file) |  |
50 KB | Bottom side showing Bowden connector mount. | 1 |
| 13:12, 10 August 2015 | Reloaded Bowden 1a.jpg (file) |  |
93 KB | Greg's Wade's Geared Extruder Reloaded, Bowden remix by Alberto Valero, November 2012. | 1 |
| 06:36, 11 December 2014 | Ramps fan bracket2a.jpg (file) |  |
390 KB | Arduino Mega 2560 + RAMPS 1.4 + 80mm fan stack powered on. | 1 |
| 20:57, 19 December 2014 | RAMPS 1.4 1b.jpg (file) |  |
535 KB | Inexpensive "Made in China" RAMPS 1.4 board without stepper driver boards. | 1 |
| 22:05, 22 June 2015 | PRUSA i3 steel 3mm lasercut 2.5DXL e irobri color.jpg (file) |  |
262 KB | P3Steel version 2.5 | 1 |
| 22:11, 22 June 2015 | PRUSA i3 steel 3mm lasercut 2.5DXL e irobri.dwg.zip (file) |  |
85 KB | DWG CAD source file for P3Steel V2.5 DXL (zipped) | 1 |
| 23:54, 13 December 2014 | PRUSA i3 steel 3mm lasercut 2.01d irobri color.jpg (file) |  |
301 KB | For reference only. Low-res drawing of P3Steel version 2.01. | 1 |
| 21:13, 3 December 2014 | PRUSA i3 steel 3mm lasercut 2.01d irobri.dwg (file) | |
104 KB | CAD file for Prusa P3Steel, version 2.01. This is released under the same license as Irobri's original .dwg CAD file for version 2.0. | 1 |
| 21:23, 3 December 2014 | PRUSA i3 steel 3mm lasercut 2.01 irobri.jpg (file) |  |
115 KB | Prusa P3Steel version 2.01. | 1 |
| 18:04, 17 December 2014 | P3Steel x-axis motor end 2a.jpg (file) |  |
754 KB | P3Steel Improved X motor end by AndrewBCN. | 1 |
| 17:06, 17 December 2014 | P3Steel x-axis motor end 1a.jpg (file) |  |
688 KB | X motor end complete. | 1 |
| 19:03, 13 December 2014 | P3Steel x-axis 1a.jpg (file) |  |
244 KB | The P3Steel X-axis assembly with a specific combination of Vitamins (the printed parts). | 1 |
| 22:32, 13 December 2014 | P3Steel useless part 1a.jpg (file) |  |
441 KB | Useless part removed in version 2.01 of the P3Steel frame. | 1 |
| 16:32, 28 October 2014 | P3Steel small m3 thumbwheels 1.jpg (file) |  |
732 KB | Small, low profile m3 thumbwheels here fitted with niloc nuts. | 1 |
| 07:31, 21 December 2014 | P3Steel ramps printing 2a.jpg (file) |  |
515 KB | Arduino Mega 2560 + RAMPS 1.4 + 4 x A4988 stepper drivers + 80mm fan stack, during a print. | 1 |
| 05:07, 24 October 2014 | P3Steel painted parts 1.jpg (file) |  |
776 KB | After many days, all the P3Steel frame parts are painted. I gave up on yellow and used dark blue for some parts. | 1 |
