File list

Jump to: navigation, search

This special page shows all uploaded files.

File list
 
First pagePrevious pageNext pageLast page
Date Name Thumbnail Size Description Versions
16:17, 12 June 2010 ElasticCurve.png (file) 4 KB   1
13:40, 18 July 2010 TrigearsExample4.png (file) 5 KB example output of MATLAB gear center distance program 1
13:50, 9 November 2013 Nut and bolt drawing.png (file) 7 KB   1
14:28, 22 January 2011 Switch circuit.png (file) 8 KB   1
01:17, 31 May 2010 CompliantMechanismSheetmetal.zip (file) 11 KB Compliant mechanism 2D sheet metal pattern in svg, pdf, and dxf formats (all generated with InkScape) 1
18:06, 10 May 2013 Depositing poled PVDF.JPG (file) 12 KB   1
18:05, 10 May 2013 Printed PVDF bimorph actuator.JPG (file) 18 KB   1
15:46, 31 May 2013 GoogleTrendsReprap.PNG (file) 22 KB   1
20:40, 13 October 2013 MinimugSTL.jpg (file) 24 KB OpenSCAD render of the minimug object, a RepRap's traditional first print. 1
01:05, 25 May 2010 Link-cartoon2.PNG (file) 25 KB Compressed, equilibrium, and extended cases of planar compliant mechanism. 1
02:03, 10 November 2013 ReprapBounty 02.jpg (file) 27 KB   1
16:37, 7 June 2010 BendingExample.PNG (file) 34 KB added expression for maximum deflection 2
00:23, 15 September 2013 My Parts 0.jpg (file) 38 KB   1
02:16, 25 May 2010 CompliantMechanismFiles.zip (file) 40 KB pdf, dwg, and openSCAD for prototype compliant linear mechanism 1
18:00, 21 January 2011 PaperInstructions.JPG (file) 41 KB order of gluing operations for assembling a compliant mechanism 1
12:14, 5 November 2013 Edm for drilling nozzle.png (file) 42 KB   1
12:46, 18 July 2010 Motor.jpg (file) 46 KB motor assembly with gears simultaneously meshing with rack 1
01:32, 10 November 2013 ReprapBounty 13.jpg (file) 51 KB   1
02:12, 10 November 2013 ReprapBounty 10.jpg (file) 51 KB   1
13:10, 16 November 2013 Edm schematic.png (file) 53 KB   2
14:20, 22 January 2011 Example2.JPG (file) 64 KB metal extruder test 2 1
13:00, 18 July 2010 AngleDefinitions.png (file) 64 KB Diagram of gear angles to accompany page on simultaneous gear meshing 1
00:24, 15 September 2013 Piezo Testing 01.jpg (file) 68 KB   1
01:26, 15 September 2013 PiezoPlates2.jpg (file) 69 KB   1
13:42, 9 November 2013 Nut and bolt assembled.jpg (file) 72 KB   1
16:53, 10 April 2010 WaxVacuum3.jpg (file) 74 KB wax vacuum image 1
13:54, 22 January 2011 MetalSyringeParts.zip (file) 75 KB stl and dxf format CAD files for syringe pump metal extruder 1
01:40, 11 April 2010 Waxuum1.jpg (file) 78 KB First attempt. This is just a single-tube needle with a heater and thermistor. The air tube is stuck in place with caulk. The lid, heater, ports, etc are held in place with JB-weld. This design did not work at all because there was not sufficient heat 1
14:20, 22 January 2011 Example1.jpg (file) 78 KB metal extruder test 1 1
13:49, 9 November 2013 Nut and bolt unassembled.jpg (file) 79 KB   1
16:54, 10 April 2010 Waxuum case parts.zip (file) 80 KB waxuum case parts 1
02:06, 10 November 2013 ReprapBounty 03.jpg (file) 81 KB   1
01:45, 11 April 2010 Waxuum5.jpg (file) 81 KB Push-to-connect fitting visible on back. 1
12:48, 18 July 2010 Multigear.zip (file) 82 KB This is MATLAB code that calculates center locations for two gears that are in simultaneous mesh with a third gear and a straight rack. 1
01:46, 11 April 2010 Waxuum9.jpg (file) 82 KB Closeup view of nested drain and vent tubes at the cutting tip. 1
02:10, 10 November 2013 ReprapBounty 07.jpg (file) 88 KB   1
01:42, 11 April 2010 Waxuum3.jpg (file) 90 KB Second attempt. Vent and drain tubes run in parallel, with a sort of notch at the tip to allow molten wax to be replaced with air from the vent, then moved up the drain tube into the case. Push-to-connect fitting (visible behind case) is used to connect 1
23:59, 31 August 2013 Drops After Print 02.png (file) 91 KB   1
14:28, 22 January 2011 NozzleParts.jpg (file) 92 KB   1
19:22, 9 November 2013 WikiHowTo 02.JPG (file) 97 KB   1
00:38, 31 May 2010 EtchScriber11.jpg (file) 97 KB   1
02:08, 10 November 2013 ReprapBounty 06.jpg (file) 97 KB   1
00:50, 31 May 2010 EtchScriber12.jpg (file) 98 KB   1
00:49, 31 May 2010 EtchScriber10.jpg (file) 103 KB   2
19:21, 9 November 2013 WikiHowTo 01.JPG (file) 108 KB   1
00:37, 31 May 2010 EtchScriber9.jpg (file) 110 KB   1
01:43, 11 April 2010 Waxuum6.jpg (file) 113 KB Third attempt. This one worked well enough to test. Solidified wax forms a film on the inside of the case. This design uses a nested drain and vent. The cutting tip exits to the left in the picture. The vent exits to the right. An eight-ohm heater i 1
19:22, 9 November 2013 WikiHowTo 04.JPG (file) 116 KB   1
22:47, 1 August 2012 MetalMandrel01.jpg (file) 116 KB   1
00:32, 31 May 2010 EtchScriber1.jpg (file) 118 KB   1
First pagePrevious pageNext pageLast page