Search results

Create the page "Stripboard" on this wiki! See also the search results found.

• ElectronicsFabricationGuide
  ...irst unless it is brand, spanking new with a mirror finish (see section on stripboard). Now you can start to solder stripboard. You did remember this is a practice run, right? Put the victim part in the
  11 KB (1,935 words) - 02:45, 29 December 2014
• ExtruderIO
  * [[BuildingAStripboardExtruderController|A Stripboard Extruder Controller]] - This includes some details on heater element sizing
  20 KB (3,214 words) - 02:37, 4 March 2014
• Old RepRap project FAQ
  ...t because there are so many wires to connect (they don't use a PCB or even stripboard). It works just fine though because I made mine as described, but it may b
  26 KB (4,452 words) - 14:31, 29 February 2012
• Generation 3 Electronics
  ...Mendel USB and power connector]] (no Eagle design - it's a simple piece of stripboard),
  10 KB (1,606 words) - 20:53, 19 February 2012
• MagServo
  I rapid prototyped a holder for a small piece of stripboard to go on the back of one of the geared motors that I used for the [[Thermop The larger part holds the stripboard for the electronics, and attaches using two 30 mm M3 cap screws to the hole
  11 KB (1,962 words) - 06:47, 13 May 2016
• OptoEndstop 2 0
  ...the ZD1901 opto interrupter prevalent in the Southern Hemisphere, a simple stripboard assembly is required. Details [[DarwinZD1901Opto|here]].
  6 KB (986 words) - 09:44, 2 October 2012
• OptoEndstop 2.1
  ...the ZD1901 opto interrupter prevalent in the Southern Hemisphere, a simple stripboard assembly is required. Details [[OptoEndstop_2_1#ZD1901_Opto_Switch|here]].
  16 KB (2,480 words) - 09:52, 14 December 2014
• Power Distribution and Communications Board v1.3
  * Which is based on the older, [[BuildingAStripboardCommsController|stripboard comms controller]] designed by Simon.
  22 KB (3,564 words) - 04:47, 25 July 2015
• ShowCase
  ...rap.org/mediawiki/index.php?title=Special%3ASearch&search=stripboard&go=Go stripboard].
  9 KB (1,479 words) - 18:30, 26 November 2011
• StepperDriverWithUDN2559
  * Top view of 2559 Stepper Motor on Stripboard: <br />
  900 bytes (130 words) - 06:13, 29 November 2014
• StepperTester Stripboard
  ...Rap controller boards. It is very simple to solder up on an old offcut of stripboard, or you can get a proper [http://parts.rrrf.org/product_info.php?products_i
  1 KB (230 words) - 20:05, 26 November 2011
• Stepper Motor Driver 1.2
  ...also cheap, only $5.00 USD. It is also apparently possible to build it on stripboard - if you do so, please share the instructions with us!
  24 KB (4,088 words) - 05:55, 29 November 2014
• Build A Stripboard Bipolar Slave Stepper Controller
  = HOWTO: Build A Stripboard Bipolar Slave Stepper Controller = * [[StripboardBipolarStepperController|HOWTO Build a Stripboard Bipolar Stepper Controller]]
  1 KB (158 words) - 05:08, 25 July 2015
• Build A Stripboard Bipolar Stepper Controller
  = HOWTO: Build A Stripboard Bipolar Stepper Controller = ...order repeatedly. The pinouts are 1 to 4 as seen from the top-down on the stripboard. Where you see 1->2 this means the voltage measured from pin 1 (negative p
  6 KB (906 words) - 05:09, 25 July 2015
• StripboardBipolarStepperController
  #REDIRECT [[Build A Stripboard Bipolar Stepper Controller]]
  59 bytes (7 words) - 05:09, 25 July 2015
• Stripboard JDM PIC Programmer
  ...ication on plain perforated board. The design outlined here uses the same stripboard methods as suggested for other modules and is simpler to build. This image shows the rear of the stripboard so you can see the points that were separated.
  7 KB (1,092 words) - 05:11, 25 July 2015
• ThermoplastExtruder
  ...made the circuit for driving the extrusion head conventionally on 2.54 mm stripboard. ...tomatically creating PCBs if you want to etch one, rather than building on stripboard. If you do that, put two 3 mm mounting holes on one edge of the PCB 32 mm
  52 KB (8,773 words) - 09:49, 5 January 2015
• ThermoplastExtruder 2 0 BoM
  ...I did not have a [[PWM_Driver_1_1|RepRap PWM PCB]] to hand, and it is that stripboard circuit that is shown.
  2 KB (344 words) - 14:19, 29 November 2011
• Universal Controller Board v1.1
  ...Rap controller boards. It is very simple to solder up on an old offcut of stripboard. ...u want to do this, put a 7-pin connector in for P11, make up your circuit (stripboard is probably easiest), and put a 7-way socket on the board that will plug in
  19 KB (3,040 words) - 04:53, 25 July 2015
• Universal Controller Board v1.2
  ...u want to do this, put a 7-pin connector in for P11, make up your circuit (stripboard is probably easiest), and put a 7-way socket on the board that will plug in
  31 KB (5,053 words) - 04:54, 25 July 2015

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)