Search results
Create the page "Stripboard" on this wiki! See also the search results found.
- ...l 7 Segment LCD displays '''And a [[PCB Heatbed | Prusa HBP board]] Note: Stripboard shown in the photo is only a placeholder. I'll get the HBP ordered soon.12 KB (1,833 words) - 07:35, 2 January 2015
- ...opto interrupter gebruiken (meestal het zuidelijk halfrond) is een simpel stripboard assembly benodigd. Details [[OptoEndstop_2_1#ZD1901_Opto_Switch|zijn hier t15 KB (2,342 words) - 09:54, 14 December 2014
- | [[Heated_Bed#Stripboard_PCB_as_a_heating_Element|Stripboard PCB heating element]] (cheap, but effective) || [http://www.veroboard.com/444 KB (6,727 words) - 11:30, 29 April 2020
- ...uits.agustinaandreoletti.com/temperature/pcb-heater/ "PCB heater"] using a stripboard PCB and a bit of soldering.4 KB (581 words) - 14:00, 7 November 2015
- There's an Arduino Due on the left feeding into a stripboard to shift levels to/from 3V3 from/to 5V in the middle. That feeds into a stripboard pretend-ATmega644P-chip in a [[Sanguinololu]] on the15 KB (2,402 words) - 11:18, 3 July 2020
- ==Stripboard PCB as a heating Element== ...thingiverse is an example, with a link to one supplier of large (10x4 inch)stripboard for $2.65 each. So about $5 plus S&H for a HPB circuit board.26 KB (3,397 words) - 10:35, 2 November 2018
- #REDIRECT [[Stripboard JDM PIC Programmer]]43 bytes (5 words) - 05:10, 25 July 2015
- #REDIRECT [[Build A Stripboard Bipolar Slave Stepper Controller]]65 bytes (8 words) - 05:08, 25 July 2015
- ==Stripboard PCB as a heating Element==30 KB (5,032 words) - 08:30, 20 October 2015
- ==Stripboard PCB as a heating Element==31 KB (5,063 words) - 11:02, 2 November 2018
- ...irst unless it is brand, spanking new with a mirror finish (see section on stripboard). Before ever connecting power to a newly made stripboard it is essential to test the board. One common problem is flakes of copper19 KB (397 words) - 16:57, 2 August 2019
- ...le electronics that can be printed by RepRap itself. Can also be built on stripboard. Fully tested, and supported by the standard RepRap software. ...ew%20Front%20Page/Documentation/Tools/Stripboard%20designer.htm]. See the "Stripboard Designer" section of [[Useful Software Packages]].18 KB (2,604 words) - 08:58, 6 May 2020
- ...le electronics that can be printed by RepRap itself. Can also be built on stripboard. Fully tested, and supported by the standard RepRap software. ...ew%20Front%20Page/Documentation/Tools/Stripboard%20designer.htm]. See the "Stripboard Designer" section of [[Useful Software Packages]].18 KB (2,604 words) - 08:59, 6 May 2020
- ...le electronics that can be printed by RepRap itself. Can also be built on stripboard. Fully tested, and supported by the standard RepRap software. ...ew%20Front%20Page/Documentation/Tools/Stripboard%20designer.htm]. See the "Stripboard Designer" section of [[Useful Software Packages]].18 KB (2,604 words) - 08:59, 6 May 2020
- ...holes. The end of the connector should be just flush with the edge of the stripboard.<br clear="all">[[Image:Usb-pcb-connections.jpg]][[Image:Usb-wire.jpg]] ...on the left view. Use a thin cable tie to attach the ribbon cable to the stripboard via the smaller holes. Leave a small loop free to give strain relief. Jum5 KB (921 words) - 21:29, 24 November 2023
- ...holes. The end of the connector should be just flush with the edge of the stripboard.<br clear="all">[[Image:Usb-pcb-connections.jpg]][[Image:Usb-wire.jpg]] ...on the left view. Use a thin cable tie to attach the ribbon cable to the stripboard via the smaller holes. Leave a small loop free to give strain relief. Jum5 KB (921 words) - 21:29, 24 November 2023
