User contributions
- 14:53, 21 March 2020 (diff | hist) . . (+18) . . G-code (→M117: Display Message: Klipper supports this)
- 22:50, 20 March 2020 (diff | hist) . . (+254) . . G-code (→M300: Play beep sound: Add info on M300 on Klipper)
- 22:43, 20 March 2020 (diff | hist) . . (+17) . . G-code (→M205: Advanced settings: Unsupported by klipper)
- 09:38, 18 March 2020 (diff | hist) . . (+133) . . G-code (→G2 & G3: Controlled Arc Move: Klipper supports this)
- 09:35, 18 March 2020 (diff | hist) . . (+666) . . G-code (Add all Klipper virtual SD card commands support)
- 09:27, 18 March 2020 (diff | hist) . . (+117) . . G-code (→M20: List SD card: Klipper supports this)
- 09:21, 18 March 2020 (diff | hist) . . (+18) . . G-code (→M115: Get Firmware Version and Capabilities: Klipper supports this)
- 09:20, 18 March 2020 (diff | hist) . . (+18) . . G-code (→M114: Get Current Position: Klipper supports this)
- 09:18, 18 March 2020 (diff | hist) . . (+17) . . G-code (→M112: Full (Emergency) Stop: Klipper supports this)
- 09:16, 18 March 2020 (diff | hist) . . (+18) . . G-code (→M107: Fan Off: Klipper supports this)
- 09:14, 18 March 2020 (diff | hist) . . (+18) . . G-code (→M106: Fan On: Klipper supports this)
- 09:13, 18 March 2020 (diff | hist) . . (+18) . . G-code (→M190: Wait for bed temperature to reach target temp: Klipper supports this)
- 09:12, 18 March 2020 (diff | hist) . . (+18) . . G-code (→M140: Set Bed Temperature (Fast): Klipper supports this)
- 09:11, 18 March 2020 (diff | hist) . . (+362) . . G-code (→M109: Set Extruder Temperature and Wait: Klipper supports this)
- 09:06, 18 March 2020 (diff | hist) . . (+30) . . G-code (→M104: Set Extruder Temperature)
- 09:04, 18 March 2020 (diff | hist) . . (+18) . . G-code (→M105: Get Extruder Temperature: Klipper supports this)
- 09:03, 18 March 2020 (diff | hist) . . (+18) . . G-code (→M204: Set default acceleration: Klipper supports this)
- 09:01, 18 March 2020 (diff | hist) . . (+18) . . G-code (→M83: Set extruder to relative mode: Klipper supports this)
- 09:00, 18 March 2020 (diff | hist) . . (+18) . . G-code (→M82: Set extruder to absolute mode: Klipper supports this)
- 08:59, 18 March 2020 (diff | hist) . . (+331) . . User talk:Adrianbowyer (→reprap.org SMTP is in a SPAM blacklist: new section)
- 08:54, 18 March 2020 (diff | hist) . . (+18) . . G-code (→M220: Set speed factor override percentage: Klipper supports M220)
- 08:53, 18 March 2020 (diff | hist) . . (+18) . . G-code (→M400: Wait for current moves to finish: Klipper supports M400)
- 08:49, 18 March 2020 (diff | hist) . . (+131) . . G-code (→M84: Stop idle hold: Klipper supports M84)
- 08:46, 18 March 2020 (diff | hist) . . (+18) . . G-code (→M18: Disable all stepper motors: Klipper supports M18)
- 08:45, 18 March 2020 (diff | hist) . . (+18) . . G-code (→G0 & G1: Move: Klipper supports G0/G1)
- 08:43, 18 March 2020 (diff | hist) . . (+17) . . G-code (→M205: EEPROM Report: No repetier EEPROM stuff in Klipper (M205))
- 08:42, 18 March 2020 (diff | hist) . . (+17) . . G-code (→M203: Set maximum feedrate: Klipper does not support M203)
- 08:40, 18 March 2020 (diff | hist) . . (+17) . . G-code (→M201: Set max printing acceleration: Klipper does not support M201)