Search results

Jump to: navigation, search

Create the page "Useful Software Package" on this wiki! See also the search results found.

  • Basic Starter Working Configurations
    So make this as useful as possible we need to define a standard method to define the basic configu Each configuration below specifies working combinations of electronics and software. The mechanical aspects of the machine (i.e. Darwin, Mendle, etc) are omit
    5 KB (506 words) - 20:34, 8 August 2011
  • RAMPS 1.3
    ...is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino MEGA with the powerful Arduino ME You will need the Arduino software at http://www.arduino.cc/en/Main/Software to upload the firmware to Arduino Mega.
    23 KB (3,768 words) - 18:06, 7 March 2019
  • Azteeg X3
    We've combined the RAMPS and the Arduino Mega into one sleek package, added lots of cool stuff, beefed up power handling and made the Azteeg X3 ;*Compact and sleek package. 4.35" x 2.85" Board size
    16 KB (2,667 words) - 11:27, 9 July 2015
  • Gen7 Board 1.3.1
    This allows talking to the ATmega only and may be useful for firmware programming. Leave the ATX24 and both Disk Power headers empty ...end is close to the ATX24 header. Done right, you can read the text on the package from the ATX24 header side correctly.
    37 KB (5,868 words) - 15:08, 14 November 2015
  • RAMPS 1.2
    ...is designed to fit the entire electronics needed for a RepRap in one small package for low cost. It is a "1.5 layer" designed board (i.e. it's double sided bo Here's the Arduino website: http://www.arduino.cc/en/Main/Software
    33 KB (5,279 words) - 13:40, 1 May 2013
  • Printrun
    sudo yum install printrun # for the whole package, or: Note: The previous package, 'printrun-gui' is currently broken on Ubuntu 'precise', but may work on pr
    9 KB (1,319 words) - 13:46, 17 September 2019
  • Installing RepRap on your computer/fr
    {{Alternative Toolchain Notice|software|install}} * [[Useful Software Packages]]
    14 KB (2,213 words) - 07:09, 16 January 2015
  • Gen L Electronics
    ...lectronics is an in-development electronics package optimized for cost and software hackability == Software ==
    3 KB (490 words) - 12:39, 14 December 2014
  • Ppa install
    Here is Jonathan Marsden's personal package archive with the RepRap Debian/Ubuntu packages: To get the software for loading firmware into the Sanguino chip, issue the following commands (
    1 KB (143 words) - 17:17, 24 November 2011
  • Debian package
    These are my notes on getting a debian package operational for reprap. I'm starting of using the debian package in the reprap hosts project.
    651 bytes (94 words) - 18:52, 26 March 2014
  • RUG/Pennsylvania/State College/RepRap Media Timeline
    Summary: A 3D printing enthusiast set out to prove that useful items can be created by RepRaps by designing and printing all necessary par ...ty of Nevada, Reno has added two 3D printers, a 3D scanner, and supporting software available for general use to the school community. Thanks to professor Tod
    152 KB (22,645 words) - 01:20, 30 August 2019
  • LongboatPrusa
    * A Dremel is useful for trimming the M8 mudguard washers ...tensioned so that there is little or no slack. (a second pair of hands is useful for this)
    49 KB (8,221 words) - 09:42, 26 March 2014
  • PrusaBuildNotesBraino
    I'm not do good with electronics (I'm more of a software guy), and saved my self at least a couple weeks with the solidoodle part. == Software ==
    59 KB (9,978 words) - 17:05, 12 April 2015
  • LulzBot/AssembledPrusaMendel/gettingstarted
    ...setting up your printer make sure all of the items on the list are in your package. =Getting software=
    14 KB (2,517 words) - 12:37, 14 March 2012
  • Stepper motor driver
    ! Package ...s 1/16 microstepping, and some people prefer this TSSOP package over a QFN package.
    23 KB (3,496 words) - 07:24, 1 May 2018
  • USBasp
    ...ore'' the 10pin header, made sure there were no solder-bridges and ran the software.<br> =Software=
    4 KB (664 words) - 01:01, 23 August 2015
  • FilamentEsunplaReviews
    From the time I sent the money via paypal, it took 13 days to receive the package in Pennsylvania, USA. ...ite a bit when idle in the extruder. After that, and adjusting my extruder/software for the 1.7mm filament, I started Printing.
    5 KB (883 words) - 11:51, 19 March 2014
  • Printrboard
    ==Software== ...ac/Linux: packaged with [http://www.atmel.com/tools/FLIP.aspx Atmel's FLIP software].
    23 KB (3,566 words) - 13:32, 11 March 2020
  • Gen7 Board 1.4.1
    * Download and unpack or install the [http://arduino.cc/en/Main/Software Arduino IDE]. You need v1.0.3 or later. If you insist on v0023 or earlier f ...bootloader. Bootloader binaries come with the [[Gen7 Arduino IDE Support]] package, so upload instructions can also be found [[Gen7 Arduino IDE Support#Bootlo
    52 KB (8,394 words) - 15:13, 14 November 2015
  • Azteeg X1
    ...t 12v power supply of yours). You need to use a higher rated TVS diode(SMB package) if using a higher voltage power supply.}} === Software ===
    13 KB (2,228 words) - 18:42, 18 November 2014

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)

Retrieved from "https://reprap.org/wiki/Special:Search"