Subject		Views	Posts	Last Post
	Ramps 1.4 Mk1 heatbed atx power supply stops by willinilli	1,200	8	12/05/2013 01:09PM Last Post by uncle_bob
	Heatbed/Hotend cool off before hitting ABS temps   (Pages: 1 2) by Nununugent	1,949	32	12/05/2013 01:01PM Last Post by uncle_bob
	Reprap calibration, gcode and units by aegis1980	1,103	6	12/05/2013 10:36AM Last Post by neilrudd
	Are (most) all 1 KG filament spools a standard size? by Maxx Mayhem	13,197	17	12/04/2013 05:55PM Last Post by uncle_bob
	completed an old Techzone Mendel (firmware?) by richw8341	449	4	12/04/2013 03:13PM Last Post by Yvan
	Can't level bed on Prusa i2 by devonv	1,788	8	12/04/2013 12:46PM Last Post by uncle_bob
	Z Axis wont go down in ponterface!!! by Versone	685	4	12/04/2013 07:42AM Last Post by uncle_bob
	Ord Hadron - Z Axis won't move down   (Pages: 1 2) by goochy	6,150	52	12/04/2013 07:40AM Last Post by uncle_bob
	Extruder help by Rooski	602	3	12/04/2013 07:33AM Last Post by uncle_bob
	OLED Display by OliverP611	1,595	6	12/03/2013 03:55PM Last Post by mekmekmek
	extrusion, layer hight, feed rate, what to do? by cat.farmer	1,204	7	12/03/2013 12:39PM Last Post by uncle_bob
	Choosing a first printer by aknapp	572	7	12/03/2013 12:22PM Last Post by uncle_bob
	How to calibrate the print center?? by matrix4721	1,690	7	12/03/2013 09:03AM Last Post by matrix4721
	Do you print unattended: overnight or away? by sciome	14,121	18	12/02/2013 10:12AM Last Post by twitch
	Multi-colour hotend hits the bulldog clip. by ottovdv	936	5	12/02/2013 06:47AM Last Post by plexer
	RAMBO Board Problem Printing Circles by ralphferro	671	4	12/01/2013 10:15PM Last Post by uncle_bob
	Best 3D printer control board to upgrade to! by bardiaesm	1,110	10	12/01/2013 06:12PM Last Post by ralphferro
	Gah. Fried Power Supply - defective? by bryancostanich	648	7	11/30/2013 03:14PM Last Post by bryancostanich
	Redefining G28 by JeMor	735	5	11/30/2013 02:57PM Last Post by JeMor
	Help i need to use my 3D printer with Out hotbed by hectoralbertosoto	528	5	11/30/2013 02:50PM Last Post by uncle_bob
	Pronterface missing buttons in MacBookPro Retina by bryancostanich	1,026	2	11/30/2013 11:28AM Last Post by uncle_bob
	Using 3d printer without hotbed by hectoralbertosoto	775	2	11/30/2013 07:38AM Last Post by woodencase01
	New RepRapPro Mono - Only moves for a few seconds, then stops by bryancostanich	349	5	11/29/2013 05:12PM Last Post by bryancostanich
	Can i use kapton to wrap the 100k thermistor? by bryancostanich	969	7	11/29/2013 08:02AM Last Post by plexer
	Orienting the Print by NewPrintMan	1,130	8	11/28/2013 11:18PM Last Post by uncle_bob
	Too small holes ! by Berra	751	7	11/28/2013 03:28AM Last Post by Berra
	Printer electronics tripping out my computer????? by matrix4721	1,046	15	11/27/2013 09:55PM Last Post by uncle_bob
	can I use hook 2 power supplies in parallel? by sciome	1,110	12	11/27/2013 05:57PM Last Post by BlackDragon
	3d Artist looking to build 3d printer by mojon	1,008	13	11/26/2013 07:42AM Last Post by uncle_bob
	RepRapPro Mendel, correct axis movement by vandborg	391	5	11/26/2013 07:40AM Last Post by uncle_bob