Subject		Views	Posts	Last Post
	My temperature sensors aren't temperature sensing. by Prancytime	591	1	01/05/2013 11:00PM Last Post by Prancytime
	Heatbed ? by Berra	522	1	01/05/2013 09:46AM Last Post by Berra
	Reflective sensor by hinge	1,067	6	01/04/2013 08:22AM Last Post by bobc
	Filament knotting in extruder by leadinglights	1,061	7	01/04/2013 06:22AM Last Post by leadinglights
	abs zits and extraneous material by mpmumau	1,095	5	01/03/2013 02:42PM Last Post by HansPeterHaastrup
	Hey, I'm new here and I have a few questions by GofiLorD	660	4	01/02/2013 04:46PM Last Post by juergen99
	Does heatbed thermister size matter? by cstolpe	554	2	01/02/2013 04:17PM Last Post by xiando
	Heated bed - need to be turned on for entire print? by dslc	5,434	13	12/28/2012 06:36PM Last Post by xiando
	East london rep-rapraper's by BowHendy	737	4	12/28/2012 05:31AM Last Post by BowHendy
	MK2A changing bed height while heating up by joestefano	751	2	12/27/2012 12:44PM Last Post by Dirty Steve
	ABS juice by gerv	1,928	8	12/27/2012 12:29PM Last Post by gerv
	What are firmware updates? by wety	564	2	12/27/2012 09:47AM Last Post by jbernardis
	Is this a good deal? by Asger	1,705	29	12/26/2012 11:33AM Last Post by nophead
	Lubricating LM8UU/LM10UU bearings by jbernardis	3,954	7	12/24/2012 01:14PM Last Post by uGen
	My print has mange by leadinglights	876	7	12/24/2012 11:45AM Last Post by nophead
	Testing photo sensor by monocultured	6,940	11	12/23/2012 03:35AM Last Post by medical istrumentation engineering
	Please Help with Layer Smash... by Komb'	1,076	11	12/21/2012 06:25AM Last Post by imecproto
	Makergear hot end woes by Mazaw	1,082	5	12/20/2012 03:46PM Last Post by dean448
	Trying to run an Orca 0.4, with wade's by Uglerimosen	791	2	12/20/2012 12:10PM Last Post by Uglerimosen
	lcd and smart controller not working by cwalker1960	2,460	5	12/20/2012 08:39AM Last Post by zacbot
	Complex problem with new prusa please help by That_new_guy_223	1,122	15	12/18/2012 09:34PM Last Post by Salil Kadam
	How to connect power supply to gen6? by Pixbae	832	2	12/17/2012 09:24PM Last Post by Pixbae
	wades extruder install by fahraynk	652	2	12/17/2012 03:57PM Last Post by Komb'
	filament feed problems need help! by aduy	1,961	7	12/17/2012 03:33PM Last Post by coelestinian
	Sparking ramps board and hot bed loosing temp by duttonw	873	3	12/15/2012 08:23PM Last Post by duttonw
	Reprap Mondo, just made one if anyone needs advice by sealdogfish	1,016	4	12/14/2012 10:40PM Last Post by antithisestablishmentsterrorism
	Another success story! by Phizinza	880	6	12/13/2012 04:08AM Last Post by konwiddak
	Layer shift on Y axis by thecrazy	868	8	12/12/2012 02:16PM Last Post by Polygonhell
	What power supply to use by joestefano	918	3	12/11/2012 05:07PM Last Post by thecrazy
	Annoying silk-like ooze by Physics_Dude	1,579	14	12/11/2012 04:59PM Last Post by thecrazy