mendel commisioning - need help February 23, 2014 10:18PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help February 24, 2014 02:38AM |
Registered: 12 years ago Posts: 1,592 |
Re: mendel commisioning - need help February 24, 2014 08:07PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help February 24, 2014 08:20PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help February 24, 2014 11:49PM |
Registered: 11 years ago Posts: 241 |
Quote
Basicblacklabel.com
notice the bed isnt centered in the frame. is this a problem?
Re: mendel commisioning - need help February 25, 2014 02:07AM |
Registered: 12 years ago Posts: 1,592 |
Quote
Basicblacklabel.com
here is my sprinter arduino sketch
Re: mendel commisioning - need help February 25, 2014 11:58AM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help February 25, 2014 12:33PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help February 25, 2014 09:02PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help February 25, 2014 10:21PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help February 26, 2014 12:11AM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help February 26, 2014 01:17AM |
Registered: 12 years ago Posts: 1,592 |
Re: mendel commisioning - need help February 26, 2014 05:02PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help February 27, 2014 04:34AM |
Registered: 12 years ago Posts: 1,592 |
Re: mendel commisioning - need help February 27, 2014 05:30PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help February 27, 2014 05:51PM |
Registered: 12 years ago Posts: 1,592 |
Re: mendel commisioning - need help February 28, 2014 02:05PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help February 28, 2014 02:45PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help March 01, 2014 12:06AM |
Registered: 12 years ago Posts: 1,592 |
Re: mendel commisioning - need help March 01, 2014 12:33PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help March 01, 2014 11:57PM |
Registered: 12 years ago Posts: 1,592 |
Re: mendel commisioning - need help March 02, 2014 01:48PM |
Registered: 11 years ago Posts: 167 |
Re: mendel commisioning - need help March 03, 2014 03:33PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help March 03, 2014 06:52PM |
Registered: 12 years ago Posts: 1,592 |
Re: mendel commisioning - need help March 03, 2014 06:52PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help March 05, 2014 01:39AM |
Registered: 12 years ago Posts: 1,592 |
Re: mendel commisioning - need help March 05, 2014 05:42PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help March 05, 2014 10:23PM |
Admin Registered: 16 years ago Posts: 1,470 |
The mechanical endstop boards require 3 wires to be connected. 1 for signal, 1 each for + and - for power. My guess is that you have + and - connected, which is why the LED on the board works, but do not have the signal wire connected.Quote
Basicblacklabel.com
I used [www.mendelcraft.com] to install my endstops. It says to use a 3 wire cable and cut one wire. My LED does light up when depressed but m119 reports no change.
Help improve the RepRap wiki!
Just click "Edit" in the top-right corner of the page and start typing. Anyone can edit the wiki! |
Re: mendel commisioning - need help March 06, 2014 12:35PM |
Registered: 10 years ago Posts: 18 |
Re: mendel commisioning - need help March 06, 2014 09:18PM |
Registered: 12 years ago Posts: 1,592 |
Quote
Basicblacklabel.com
I was able to get all endstops to know when they where being depressed but all of them were saying the opposite of what they were so I inverted endstops in sprinter firmware and they register what they should now. however my motors are not moving in a negative direction now. this seems to be an endless cycle of problems.