Sanguinololu with at1284p June 21, 2016 09:07AM |
Registered: 11 years ago Posts: 13 |
root@nostromo:~# /home/jabss/Desktop/arduino-1.6.9/hardware/tools/avr/bin/avrdude -C/home/jabss/Desktop/arduino-1.6.9/hardware/tools/avr/etc/avrdude.conf -v -patmega1284p -carduino -P/dev/ttyUSB0 -b115200 -D -Uflash:w:/tmp/build7541ecec97c971a10b8d6f10b8688134.tmp/Marlin.ino.hex:i avrdude: Version 6.0.1, compiled on Apr 14 2015 at 19:04:16 Copyright (c) 2000-2005 Brian Dean, [www.bdmicro.com] Copyright (c) 2007-2009 Joerg Wunsch System wide configuration file is "/home/jabss/Desktop/arduino-1.6.9/hardware/tools/avr/etc/avrdude.conf" User configuration file is "/root/.avrduderc" User configuration file does not exist or is not a regular file, skipping Using Port : /dev/ttyUSB0 Using Programmer : arduino Overriding Baud Rate : 115200 AVR Part : ATmega1284P Chip Erase delay : 55000 us PAGEL : PD7 BS2 : PA0 RESET disposition : dedicated RETRY pulse : SCK serial program mode : yes parallel program mode : yes Timeout : 200 StabDelay : 100 CmdexeDelay : 25 SyncLoops : 32 ByteDelay : 0 PollIndex : 3 PollValue : 0x53 Memory Detail : Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- --------- eeprom 65 10 128 0 no 4096 8 0 9000 9000 0xff 0xff flash 65 10 256 0 yes 131072 256 512 4500 4500 0xff 0xff lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 Programmer Type : Arduino Description : Arduino Hardware Version: 3 Firmware Version: 5.0 Vtarget : 0.3 V Varef : 0.3 V Oscillator : 28.800 kHz SCK period : 3.3 us avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.00s avrdude: Device signature = 0x1e9705 avrdude: safemode: lfuse reads as 0 avrdude: safemode: hfuse reads as 0 avrdude: safemode: efuse reads as 0 avrdude: reading input file "/tmp/build7541ecec97c971a10b8d6f10b8688134.tmp/Marlin.ino.hex" avrdude: writing flash (98234 bytes): Writing | ## | 4% 0.46s avrdude: stk500_paged_write(): (a) protocol error, expect=0x14, resp=0x62 Writing | ### | 5% 0.55savrdude: stk500_recv(): programmer is not responding
Re: Sanguinololu with at1284p June 21, 2016 10:05AM |
Registered: 11 years ago Posts: 13 |
/home/jabss/Desktop/arduino-1.6.9/hardware/tools/avr/bin/avrdude -C/home/jabss/Desktop/arduino-1.6.9/hardware/tools/avr/etc/avrdude.conf -v -patmega1284p -cstk500v1 -P/dev/ttyUSB0 -b19200 -Uflash:w:/root/.arduino15/packages/Sanguino/hardware/avr/1.0.0/bootloaders/optiboot/optiboot_atmega1284p.hex:i -Ulock:w:0x0F:m
avrdude -p atmega1284p -c stk500v1 -b 19200 -V -e -U lfuse:w:0xD6:m -U hfuse:w:0xDA:m -U efuse:w:0xFD:m -U flash:w:ATmegaBOOT_168_atmega1284p.hex:i
/home/jabss/Desktop/arduino-1.6.9/hardware/tools/avr/bin/avrdude -C/home/jabss/Desktop/arduino-1.6.9/hardware/tools/avr/etc/avrdude.conf -v -patmega1284p -cstk500v1 -P/dev/ttyUSB0 -b19200 -Uflash:w:/root/.arduino15/packages/Sanguino/hardware/avr/1.0.0/bootloaders/optiboot/optiboot_atmega1284p.hex:i -Ulock:w:0x0F:m -V -e -U lfuse:w:0xD6:m -U hfuse:w:0xDA:m -U efuse:w:0xFD:m