[STRANGE] echoEBUG: ?p??????a?@?? August 04, 2016 12:37PM |
Registered: 10 years ago Posts: 153 |
18:27:36.398 : Printer reset detected - initalizing 18:27:36.398 : start 18:27:36.402 : echo: External Reset 18:27:36.402 : Marlin 1.1.0-RC5 18:27:36.406 : echo: Last Updated: 2016-04-01 12:00 | Author: (none, default config) 18:27:36.410 : Compiled: Aug 4 2016 18:27:36.414 : echo: Free Memory: 4995 PlannerBufferBytes: 1232 18:27:36.418 : echo:V23 stored settings retrieved (396 bytes) 18:27:36.422 : echoteps per unit: 18:27:36.426 : echo: M92 X100.61 Y100.32 Z3996.00 E790.00 18:27:36.427 : echo:Maximum feedrates (mm/s): 18:27:36.430 : echo: M203 X350.00 Y350.00 Z3.00 E50.00 18:27:36.435 : echo:Maximum Acceleration (mm/s2): 18:27:36.435 : echo: M201 X900 Y900 Z50 E1000 18:27:36.443 : echo:Accelerations: P=printing, R=retract and T=travel 18:27:36.443 : echo: M204 P1000.00 R2000.00 T3000.00 18:27:36.459 : echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s), Z=maximum Z jerk (mm/s), E=maximum E jerk (mm/s) 18:27:36.463 : echo: M205 S0.00 T0.00 B20000 X20.00 Z0.40 E5.00 18:27:36.467 : echo:Home offset (mm): 18:27:36.467 : echo: M206 X0.00 Y0.00 Z0.00 18:27:36.472 : echoID settings: 18:27:36.476 : echo: M301 P22.20 I1.08 D114.00 C100.00 L20 18:27:36.476 : echo:Filament settings: Disabled 18:27:36.480 : echo: M200 D3.00 18:27:36.480 : echo: M200 D0 18:27:36.783 : FIRMWARE_NAME:Marlin 1.1.0-RC5 From Archive SOURCE_CODE_URL:[github.com] PROTOCOL_VERSION:1.0 MACHINE_TYPE:3D Printer EXTRUDER_COUNT:1 UUID:00000000-0000-0000-0000-000000000000 18:27:36.791 : X:0.00 Y:0.00 Z:0.00 E:0.00 Count X: 0 Y:0 Z:0 18:27:36.807 : echoEBUG: ?p??????a?@??P??`??p??????V?@??P??`??p??????K?/????????#A????|P??`??p??????a?@??P??`??p??????V?@??P??`??p??????K?/????????#A???? 18:27:36.807 : echo:Active Extruder: 0 18:27:36.828 : echoEBUG: ?p??????a?@??P??`??p??????V?@??P??`??p??????K?/????????#A????|P??`??p??????a?@??P??`??p??????V?@??P??`??p??????K?/????????#A???? 18:27:36.828 : echo:Active Extruder: 0