Welcome! Log In Create A New Profile

Advanced

Firmware - Marlin

Everything about Marlin firmware : Discussions, questions, support and feature requests... 
Page 1 of 101    Pages: 12345NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

Upgrading marlin v1.0.0 to v.2.1.2.5 - Z offset to the Bed

by uuys007 		87 8 01/18/2025 04:52AM
Last Post by uuys007

can marlin share an SD card via WIFI on skr-2 board Attachments

by mtraven 		15 2 01/18/2025 01:37AM
Last Post by Dust

Upgrading marlin v1.0.0 to v.2.1.2.5 Attachments

by uuys007 		222 5 01/16/2025 06:57AM
Last Post by uuys007

esp32(esp3D) WIFI module wont talk to marlin (serial port config?)

by mtraven 		163 7 01/15/2025 05:22AM
Last Post by mtraven

Bed Leveling marlin 2.1.2.x upgrade from marlin 1.0.0 to 2.1.2 Attachments

by uuys007 		425 21 01/15/2025 04:35AM
Last Post by uuys007

12864 LCD whith ST7565 controller and MKS Robin Nano v1

by Lbz 		143 1 01/09/2025 03:38PM
Last Post by Lbz

make touch leveling handmade sensor for my 3d printer

by famitox 		383 3 01/09/2025 04:00AM
Last Post by Dust

problems met skr pro en endstops

by corvdberg2009 		222 1 01/04/2025 01:19PM
Last Post by corvdberg2009

Compensation of surface irregularities along the Z axis ...

by z34x66 		219 1 01/01/2025 09:02AM
Last Post by z34x66

Marlin: Pin assignment for ESP32

by godageprasad 		220 4 01/01/2025 04:52AM
Last Post by Dust

Z Servo not activating after marlin v1.0.0.to v2.1.2 upgrade reprap - prusa Attachments

by uuys007 		344 9 12/27/2024 03:02AM
Last Post by uuys007

Marlin - MPSCARA not homing

by sejkon 		391 3 12/25/2024 09:37PM
Last Post by Dust

Robin Nano v3.1 + 3Dtouch + SmartFilamentSensor, USB connection

by cysign 		2,185 22 12/09/2024 03:45PM
Last Post by cysign

Add suport for Arduino GIGA R1

by Flyer2000 		394 3 12/06/2024 05:35AM
Last Post by Flyer2000

Full Graphic Smart Controller - Button doesn't do anything Attachments

by InitialDima 		525 12 11/23/2024 09:57AM
Last Post by dustinoff

ATMegaGT 2560 A+on GeeeTech i3B with BLTouch ...AND Z Min endstop?

by NeilP 		411 1 11/21/2024 06:31AM
Last Post by NeilP

MPC setup

by dustinoff 		439 1 11/19/2024 02:05PM
Last Post by dustinoff

Print to WiFi

by DoctorDeath 		400 1 11/18/2024 06:17AM
Last Post by DoctorDeath

Marlin 2.0 and STM32F103C8

by ruyvieira 		4,448 12 11/16/2024 12:48AM
Last Post by Dust

DM556 = TB6600 Stepper driver issue Attachments

by jwd 		629 3 11/10/2024 09:07AM
Last Post by jwd

Stepper Current changing Attachments

by Mr Kroll 		502 1 11/02/2024 02:03PM
Last Post by Mr Kroll

Loadtime Marlin 5 minutes + Normal ?

by RadioRon 		516 3 10/30/2024 08:19PM
Last Post by Roberts_Clif

SKR 1.4 turbo dual X configuration (X motor low holding power)

by cidokz 		485 4 10/30/2024 04:45PM
Last Post by cidokz

Changing the direction of a motor

by v1talogy 		2,202 2 10/23/2024 11:34PM
Last Post by compita23

ADVANCED_PAUSE_FEATURE - is it dumb, or is my configuration dumb?

by Andke 		531 1 10/23/2024 10:20AM
Last Post by Andke

X motor will not bump after hitting Xmin endstop or move in positive direction.

by jwd 		674 4 10/21/2024 03:51PM
Last Post by jwd

mobo burned. Try to install new board. but earlier saved Marlin INO give me lots of errors now.. Attachments

by RadioRon 		554 3 10/20/2024 05:54PM
Last Post by RadioRon

Full Graphic Smart Controller - Blank Screen Attachments

by TimoFran 		1,494 14 10/20/2024 04:39PM
Last Post by Grayerbeard

Auto_Bed_Leveling_Bilinear Issues Attachments

by grimspyder 		650 11 10/18/2024 01:32AM
Last Post by Dust

Rotational feed rate with Marlin

by genef343 		554 1 10/14/2024 06:14PM
Last Post by genef343
Page 1 of 101    Pages: 12345NextLast