Welcome! Log In Create A New Profile

Firmware - Marlin

Everything about Marlin firmware : Discussions, questions, support and feature requests...

Page 4 of 77 Pages:

1 2 345

Forum List New Topic RSS

	Views	Posts	Last Post
G29 Auto bed leveling extreme squish by NovaHuta	247	3	02/14/2021 11:04AM Last Post by NovaHuta
Layer Shift 2.0.5.3 & 2.0.7.2 MAKE IT STOP!!!! by ngen33r	226	1	02/13/2021 10:13PM Last Post by ngen33r
Help understanding SD printing Code by FiftyFive	233	3	02/12/2021 08:53PM Last Post by FiftyFive
About heating failed system stopped heater_id 0 by cthsieh	4,498	13	02/11/2021 11:36PM Last Post by mahesh joshi
Interfacing with the Wanhao i3 LCD by rgov	770	6	02/10/2021 05:35PM Last Post by JacobIpsen
Confusing Stepper Motor Behavior by ethanguidry	279	2	02/09/2021 03:59PM Last Post by VDX
Linear Advance not Working, M900 not Recognized by Mj48	371	5	02/09/2021 09:20AM Last Post by Mj48
M32 command problem by softfoot	298	3	02/09/2021 05:49AM Last Post by softfoot
Playing music at end of print ... by softfoot	472	3	02/08/2021 05:01AM Last Post by softfoot
Marlin 2.0.7.2 - Printer Stops with "Thermal Runaway Protection" by speedup	323	3	02/07/2021 03:04PM Last Post by Mj48
RE existing Marlin bug #14470 on SKR 1.3 by dant220	277	2	02/07/2021 12:56AM Last Post by dant220
Temperature reading is about twice actual temp by ivanstein	291	2	02/06/2021 06:27PM Last Post by Dust
Ender 5 plus marlin build by shish0000	305	1	02/05/2021 03:05PM Last Post by shish0000
4 motors for axis Z by n1cr0z	329	5	02/05/2021 12:53PM Last Post by dant220
[SKR 1.4] WiFi upload: "Please use 8.3 filename only." by Ohmarinus	814	8	02/05/2021 04:27AM Last Post by noobontour024
Question about 2nd Z-driver and IO for ANET A6 by DutchForeigner	238	1	02/04/2021 04:26PM Last Post by DutchForeigner
Another servo question by Mustang66	235	2	02/04/2021 04:00PM Last Post by Mustang66
Need advice for SKR V1.4 and PWM by Mustang66	287	3	02/04/2021 09:20AM Last Post by Mustang66
Issue with the service internvals by philm001	171	2	02/02/2021 09:35AM Last Post by philm001
SMART RAMPS w. Mega 2560 and AZSMZ_12864 - no SD card by NovaHuta	222	1	02/02/2021 01:01AM Last Post by NovaHuta
LCD2004 Keypad LCD - Messages don't show up correctly (Marlin 2.0.x) by malachik	249	3	02/01/2021 12:54PM Last Post by malachik
Dual Extruder on a Servo, Probe on same servo in Marlin 2.x by L3D	192	2	02/01/2021 05:45AM Last Post by L3D
Creating .h and .cpp files for device by andy2605	197	1	01/31/2021 03:25PM Last Post by andy2605
Conditionals in GCODE ??? by softfoot	207	4	01/31/2021 10:28AM Last Post by VDX
TOUCH_MI_PROBE by DrumClock	486	4	01/30/2021 09:21AM Last Post by ielorriaga
Bootloader initiation via USB - how? by etherbrat	154	3	01/30/2021 06:52AM Last Post by etherbrat
Marlin operation and connection to other boards by dquerol	315	5	01/29/2021 01:07PM Last Post by Traumflug
Commands for turning on the extruder at a particular print speed and then turning off? by fahad_ahmed89	133	4	01/28/2021 10:23AM Last Post by VDX
New serial packing protocol MEATPACK by Dust	260	1	01/28/2021 03:39AM Last Post by Dust
Serial connection timeout after a while by apfelsaftbaum	293	5	01/26/2021 08:05PM Last Post by Dust

Page 4 of 77 Pages:

1 2 345