Hi, I recently bought a prusa i3 from makerfarm. As a complete newbie to 3D printers, I was looking for an affordable kit which contains everything needed to build it and good instructions. I didn't run into any big problems while building it and if I had a quesiton Colin (from makerfarm) responded to my mails within a couple of hours... After building it, it was running the test prints withoutby Hobbit85 - General
Quotehsiegel Erfahrung ist das, was jeder selbst machen muss. ganau auf das freu ich mich... Wissen ist das eine, Erfahrung sein grosser Bruder!by Hobbit85 - Elektrik & Elektronik
Vielen Dank für eure Tipps und Erklärungen!! Ein Freund hatte noch ein Netzteil übrig - deshalb versuch ichs damit mal! Mit 2x 18A auf 12V sollte es reichen, denke ich. Und den Kabelsalat muss ich halt mal ordnen... Wenns aber nicht klappt, versuch ichs dann mal mit dem von euch vorgeschlagenen Teil! Gruss und nochmals Danke für die Unterstützung, Martinby Hobbit85 - Elektrik & Elektronik
Vielen Dank für eure Vorschläge. Sieht interessant aus. Was ist dann der Vorteil (ausser der passenden Form) gegenüber einem Netzteil mit guter Belüftung z.B. so wie ich sie vorgeschlagen habe? Platz habe ich, von demher muss ich das Netzgerät nicht dringend an den Drucker bauen, kann auch nebenan stehen... Gibt es noch andere Vorteile? Danke und Gruss, Martinby Hobbit85 - Elektrik & Elektronik
Hallo allerseits, nach langem hin und her habe ich mir kürzlich einen prusa i3 DIY kit von makerfarm.com gekauft. Der Kit beinhaltet alles, bis auf das Netzteil. Da ich bei Erhalt des Bausatzes gleich loslegen möchte, will ich das Netzteil bis dann besorgen. Aber da ich ein ziemlicher Neuling in diesem Gebiet bin, steh ich grad ein bisschen im Dschungel. Nach dem Lesen von vielen Seiten und Forenby Hobbit85 - Elektrik & Elektronik
Hi everyone, thank you very much for all the advice! Really apreciate it! I just ordered the kit with the jhead... if i need a all metal hotend later, I'll get it then... can't wait until the kit arrives!by Hobbit85 - General
Thank you all for the information! I guess, I'll take the J-head to start and then I'll see what's next... @uGen: I just bookmarked these two alternatives! Might absolutely be woth to have a look at as an alternative! And generally I prefer european based companies due to the cheaper shipping and environmental sustainability. @ShadowRam: wow thank you very much for your detailed explanation! Itby Hobbit85 - General
Ok thanks for the quick reply! QuoteOhmarinus J-head 0.5mm nozzle for 1.75mm filament. isn't the 0.5mm nozzle for the 3mm filament? or both? Sounds like a reasonable argumentation to start with a rock solid hotend which is commonly available and then upgrade if necessary... I just wonder why Colin recommended me the magma.by Hobbit85 - General
I'm going to order a prusa i3 from makerfarm as my first 3D printer. There are several options for the hotend and I'm not sure yet what I should order. The j-head seems to be a very good piece, many reprapers are using it and report good things about it. So I thought I'll go with this one, but then I heard about the new magma, which Colin recommended me as a beginner and I absolutely believe him,by Hobbit85 - General
Hi everyone, while thinking about buying a DIY 3D printer kit I searched the internet and read quite a lot about it on different blogs and forums. But still I can't figure out a couple of deciding factors on which printer kit I should buy. I'd like to use it manly as a hobby, printing some cool gadgeds I've in mind and maybe sometimes printing some architecture models for the office... I' won'tby Hobbit85 - General