dc42 thank you, I searched for math formula to calculate maximum angel that Rod Ends have at very end of Bed to verify if Traxxas can provide that kid of Swivel. I did not find any, Do you now how ? Rods are OK,and Traxxas have no play, despite being 4 years old, that is quite supriseing as Delta is enclosed and heated to about 50C to print ABSby novio8 - Delta Machines
dc42, yes bed diameter is 250mm, sorry. As I understang one has to change rod lenghts, to compensate for shorter Effector offset. I have 6mm OD Carbon rods and Traxxas Rod ends. Does new Rod lenght change stabillity or performance ? Is smaller effector less prone to tilt ?by novio8 - Delta Machines
dc42, thank you for replay distance from the mid point of the joints on the carriages to the centre is 193mm Marioby novio8 - Delta Machines
Hi, I just got second hand Kossel xl with replacement rods and effector So I have to replace rods and effector. Print Hight is 280mm and radius around 250mm. Towers are 223mm from center and Rods (Traxxas joints) are 320mm long Original effector has 40mm arm spacing and 33mm offset, replacement has the same 40mm arms pace and shorter 22mm offset Here are my questions: Should I replace Effector wby novio8 - Delta Machines
yes I tried with Superglue but bond is weak and parts can be easily separated by hand. Any other suggestion ? Marioby novio8 - General
Hi, did anyone succesfully glued PETG parts together? Which glue did you use? Any suggestions are welcomed. Regards Marioby novio8 - General
yes I did enable EEPROM and settings are Storedby novio8 - Delta Machines
By not leveled I mean when I print Bed is Convex so edges are lower than the center so extrusion on the edges is higher than in the center. I jus run M48 on several points and results are as follows 21:39:47.008 : X:0.00 Y:0.00 Z:259.24 E:0.00 Count X:54234 Y:54234 Z:54234 21:39:56.335 : M48 Z-Probe Repeatability Test 21:40:11.273 : Finished! 21:40:11.274 : Mean: 0.053735 Min: 0.049 Max: 0.05by novio8 - Delta Machines
First, when I manually leveled the Bed was Delta Radius 161,42 and I manually adjusted x,y,z endsops The bed was leveled to a certain degree. When I run G33 Delta Radius is around 164 and Bed is not leveled. I'v run G33 P3 V2 , here is code from Repetier: 13:47:30.613 : G33 Auto Calibrate 13:47:31.615 : Checking... AC 13:47:31.618 : .Height:259.42 Ex:+0.00 Ey:+0.00 Ez:+0.00 Radius:161.by novio8 - Delta Machines
what inormation you need to solve this problem? I'm more than happy to give any ingo you needby novio8 - Delta Machines
I have latest Marlin 1.1.3 I enabeled delta Calibration wit fixed Z probe. I run G33 P7, everything goes well M500, but the Bed is not leveled if I check it manually, about a millimetre or so in the center from the corners Am I doing something wrong or ? Please advise Marioby novio8 - Delta Machines
LVD Thank You, I already reduced DELTA_CALIBRATION_RADIUS. to 80 After your replay I reduced ro 60 and now it works I have one more question regardin G33, do I have to execute any other command after running G33 or are the new measurements already saved to EEPROM Regards and thanks MArioby novio8 - Delta Machines
Hi, I'm struggeling with G33 too, when I send G33 I get message M665 Bed radius implausible I'v increased or lowered #define DELTA_PRINTABLE_RADIUS 130 but I'm always getting M665 Bed radius implausible If I run Delta Calibration from LCD I can only run set Delta Hight and X,Y Z separatelly and not Auto Calibration I'm stuck Any advise will be most welcome Regards Marioby novio8 - Delta Machines