Show all posts by user
Page 3 of 5
Pages: 12345
Results 61 — 90 of 137
I tried
import ("bunny_editV1
.stl", convexity = 4);
but I didn't see anything ?
Where's the file supposed to be located ?
Thanks
by
bianchi
-
Reprappers
I try OpenScad, it can not open stl file ??
by
bianchi
-
Reprappers
For example I have 2 stl files, I can import both of them with OpenSCad and combine it ?
Thanks
by
bianchi
-
Reprappers
Guys,
I got some designs from thingverse, the file format is stl.....how can I edit and combine it with 123d design?
I need to do boolean meshmixer which is too long, is there any better way ?
Any clues ?
Thanks
by
bianchi
-
Reprappers
Yes it has a shaft, a normal bicycle pedal...
by
bianchi
-
Reprappers
do you reckon carbon inforced PLA is strong enough for a functional component ? for example a bicycle pedal ?...
thanks
by
bianchi
-
Reprappers
Guys,
I read about this :
...
Particles
As well as emitting fumes, heating ABS and PLA also emits particles. The problem with these particles is that they’re tiny, often well below 100 nm in diameter. Particles of this size are called Ultra Fine Particles (UFPDs).
When we inhale UFPs they can end up deep inside our bodies and even make their way to our brains. They can then cause inflammation
by
bianchi
-
Reprappers
Guys,
I want to print a part,
Which one is stronger between nylon and carbon reinforced PLA ?
What's the positive and negative side between of two ?
Thanks
by
bianchi
-
Reprappers
How about PLA, is the particle safe ? and nylon ?
by
bianchi
-
Reprappers
I fixed the flicker LCD with external regulator for LCD, I used LM2596......
by
bianchi
-
Reprappers
Guys,
Is the fume from nylon n abs safe enough for health?
Thanks
by
bianchi
-
Reprappers
I guess my part fan is broken I tested with battery and there's no response....and at the fan connector is 12.98V...I ll buy new fan...
What does part fan do?
by
bianchi
-
Reprappers
I have the same problem, it seems my part fan never runs, how to make it start ? thanks
by
bianchi
-
Reprappers
Guys,
Why does the second fan of my Prusa i3 never rotate ?
Where can I find the setting for it ?
Thanks
by
bianchi
-
Reprappers
What's the different between PLA and ABS ? which one is better ? thanks
by
bianchi
-
Reprappers
I have prepared 1.6mm galvanized plate, it's stiff and I'm gonna stick Builtalk on it and give a test....
by
bianchi
-
Reprappers
Guys,
Does Buildtalk have a much better sticking quality than painting mask ?
I had printed with painting mask, the result was not bad at all...
If I want to change to buildtak, it means I need to recalibrate the Z limit again.....don't I ?
Thanks
by
bianchi
-
Reprappers
I took it too close, I'll take it again later on...but if I take from far, we can not see the detail....may be zoom can help...
by
bianchi
-
Reprappers
I tried to print a square wall with the thickness 2mm with the height = 5mm and it was good...please see the photo,
I used feedrate speed 25......
And a solid cube 1cm x 1cm x 1cm.....with the speed 100mm/s
by
bianchi
-
Reprappers
Try 25 for the speed.
I will
Have you calibrated the extruder?
Yes I have, please have a look at the picture
Does the diameter of the filament match the setting in Slic3r?
Yes it does, 0.4 mm
Do single wall objects print at the correct size?
How can I make single wall object ? is it 1 mm wall ?
Have you calibrated the hot end temperature?
Yes I have, attached
What type of filament are you us
by
bianchi
-
Reprappers
I tried reducing the speed, it's tidier but still I can see the edge is not tidy, is it matter of infill or something else,
Please have a look on the result,
Thanks
by
bianchi
-
Reprappers
Where can I find feedrate in slic3r setting ?thanks
by
bianchi
-
Reprappers
Ok, I will, currently I'm using 100 as my feed rate.....try using with 90, it's abit better.....can it work on 50 ? thanks
by
bianchi
-
Reprappers
Guys,
Is this the source code for melzi board ?
Source code
I'm interested buying this board :
Melzi board
Thanks
by
bianchi
-
Reprappers
Ok, thanks for your suggestions, why the edge is not consistent ? Please have a look on the photo...
by
bianchi
-
Reprappers
Guys,
What's the different between rectlinear, line, honey comb ?
I see it at slic3r "Infill" option, which is best ? or it depends on the object I print ?
I printed a star shape but the edge is not sticking properly to the center area..
The edge looks loose....
Why is that ?
Thanks
by
bianchi
-
Reprappers
This one is hard...thin but hard...stiff
Mini Sheet 0.55 Galvabond 600x300mm
by
bianchi
-
Reprappers
I'm in Perth Australia, may be galvanized metal would be enough ? it's thin but hard....
by
bianchi
-
Reprappers
Can I use this ?metalbsheet
by
bianchi
-
Reprappers
Page 3 of 5
Pages: 12345