You need to set thermstor type to 5 to use the USER_THERMISTORTABLE0 table.von repetier - Repetier
Pi 3 is cool, just got mine:-) Getbot is not supported and will not be supported. Controller boards have more then just stepper driver and these things are missing here.von repetier - Repetier
8825 sind bekanntermaßen langsam (1,7 us high/low signal nötig). Vergiss also nicht genug pausen beim RADDS einzubauen. Ohne stepper high delay und double step delay wird er Schritte verlieren weil die nicht erkannt werden.von repetier - Elektrik & Elektronik
What is the reported crash reason. Eventually needs to check windows events to find the message if it does not show up directly. One reason could be low memory, but other reasons are possible.von repetier - Repetier
You need to fix this Marlin error 19:23:58.733 : : Extruder switched off. MINTEMP triggered ! 19:23:58.764 : Errortongue sticking out smileyrinter stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting) some thermistors are not connected or configured wrong.von repetier - Repetier
There is no prebuild combination melzi board - RRD GLCD display. So it uses pins never proposed to be used in that combination and in that case even do not exist on melzi board. Tweak ui.h to use the correct pins for that combination.von repetier - Repetier
On the right bottom is a close button. Hitting Esc key also would close the window. If you have a other DPI resuultion then 100% the button may be not visible. If so let me know - my displays all have 100% so I do not see such problems.von repetier - Repetier
Sure, read for how to use the app. You must setup server and configure host to use the server connector instead of serial connector to print over the server instead. Both ways work, so it is your preference and if you need the advantages of a server doing everything in background.von repetier - Repetier
No, wirePrint is not supported.von repetier - Repetier
24 switches per revolution = 12 cycles? Anyhow I assume this. So one cycle is 47/12 = 3,92 mm => 3,92 * 98 steps per mm = 383 steps per cycle = 100% on ideal condition. Now you could set 70% for slip detection so once it reaches 383/0.7 = 547 you will slow down to 70% Take 766 for jam detection and let the print stop. Best is of course to check in log how many steps per cycle are normal andvon repetier - Repetier
Check log and enable commands to see what gets send. The commands look right and normally sending the right command has the desired effect unless firmware has an issue, but then pronterface would not work. So maybe the solution is in the log showing an other command send. In case you have repetier-firmware also check if dry run is enabled. Should be disabled for extruder to work.von repetier - Repetier
How did you heat? Changing temperature is not enough if the icon shows disabled nothing will happen. Clock on extruder icon to toggle heating on/off.von repetier - Repetier
Yes, but only by sending G28 X0 Y0 instead of G28 which does home all axis.von repetier - Repetier
1,89V sound not so wrong. Remember the pin we read is between 4.7K and your 6.5K so just not in the center of 2.5V. So maybe the thermistor is just a different type. Have you measured resistance at room temperature? Should be near 100K at 25°C.von repetier - Repetier
It's stored in registry HKCU/Software/repetier/3Dvon repetier - Repetier
Looks like a hard one. Also no idea what goes wrong. Things to try 1. use M105 X0 so you get raw values as well. These should change with temperature 2. Try T1 instead in case there is something wrong with the pin it self on the due.von repetier - Repetier
No, the thermistor controls the fan. That's the idea. You can only define the limits with M460 X Y : Set temperature range for thermistor controlled fan the rest is temperature dependent, otherwise it makes no sense.von repetier - Repetier
You can not simply use controller 11. Also that uses u8g it uses a different chip. #ifdef U8GLIB_SSD1306_I2C u8g_InitI2C(&u8g,&u8g_dev_ssd1306_128x64_i2c,U8G_I2C_OPT_NONE); #endif #ifdef U8GLIB_SSD1306_SW_SPI u8g_InitSPI(&u8g,&u8g_dev_ssd1306_128x64_sw_spi, UI_DISPLAY_D4_PIN, UI_DISPLAY_ENABLE_PIN, UI_DISPLAY_RS_PIN, U8G_PIN_NONE, U8G_PIN_NONE); #endif Are the 2 ways tovon repetier - Repetier
You are right. Host sends it on connect with serial connector. And there is no run on connect script. So the only solution for now is to use the repetier-server as printer spooler. That would not send M80 and also has a run on connect script. Then use the server connector in host to connect with printer instead. Then it would not turn on.von repetier - Repetier
Your real problem is System.Windows.Forms.SplitContainer doesn't implement interface System.ComponentModel.ISupportInitialize which means your mono version is too old.von repetier - Repetier
We have no step by step tutorial, but we have which explains most things.von repetier - Repetier
Find in ui.h the section for your board/display combination #define UI_ENCODER_A 61 #define UI_ENCODER_B 59 #define UI_ENCODER_CLICK 43 #define UI_RESET_PIN 66 // was 41 //AE3 was here and added this line 1/25/2014 (Note pin 41 is Y- endstop!) #define UI_INVERT_MENU_DIRECTION 1 Switch encode a/b to switch all directions or UI_INVERT_MENU_DIRECTION if you only want to have different menu directvon repetier - Repetier
We are working an making bed distortion correction also work for cartesian printers. Should come the next days as version 0.92.8 together with new bed leveling implementation allowing also regression planes for better fitting without extra correction.von repetier - Repetier
It seemed that older 0.92 versions would switch to dry run without notice if the bed returns a wrong value outside allowed range. Latest 0.92.7 should require 10 such hits makeing it more unlikely plus that it now issues a message why it goes into dry run. So if it still happens with latest version check the log for the reason.von repetier - Repetier
In the editor you can jump to any layer. Use this to mark printed gcode and delete it. Stop just before the g0 Zx where you stopped. Then create start conditions like temperature and homing (hope you have zmax homing or have a place to home z without hitting print). Then just print the rest.von repetier - Repetier
You define this in your slicer. Slic3r can do it directly, for CuraEngine I use the tool change script. Kisslicer has also a option for this.von repetier - Repetier
Actually it is ROD_RADIUS that is used for horizontal distance. If you do not define it, it will be computed from PRINT_RADIUS--END_EFFECTOR_HORIZONTAL_OFFSET-CARRIAGE_HORIZONTAL_OFFSET which i sthen the horizontal radius in eeprom. Ajax is only used for online tool to reconfigure. So you will loose all changed data with next update if you change the values only in the #defines and you need tovon repetier - Repetier
The file containing u8g_com_null_fn is not included. Copy it to u8glib_ex.h and it will compile.von repetier - Repetier
Please use a more recent version of repetier. u8g was extended by many new devices and yours seems also to be included now. As well as rotate function.von repetier - Repetier
You can send any gcode even negative, that is not a problem. If I understood your comment correctly you want this to be the new z=0, whcih you can do with G92 Z0 Then firmware takes it as Z=0. Host will still show it as correct values since it adds the offset to output. Print will work none the less as expected. Correct solution is of couse to adjust your zmin endstop to correct position. WIthvon repetier - Repetier